首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
A method for the computation of phase velocities of surface waves from microtremor waveforms is shown. The technique starts from simultaneous three-component records obtained in a circular array without a central station. Then, Fourier spectra of vertical, radial and tangential components of motion are calculated for each station and considered as complex-valuated functions of the azimuthal coordinate. A couple of intermediate real physical quantities, B and C , can be defined from the 0- and ±1-order coefficients of the Fourier series expansion of such functions. Finally, phase velocities of Rayleigh and Love waves can be retrieved from B and C by solving respective one-unknown equations. The basic assumption is the possibility of expanding the wavefield as a sum of plane surface waves with Rayleigh and Love wavenumbers being univocal functions of the circular frequency. The method is tested in synthetic ambient noise wavefields confirming its reliability and robustness for passive seismic surveying.  相似文献   

2.
It has been demonstrated both theoretically and experimentally that the Green's function between two receivers can be retrieved from the cross-correlation of isotropic noise records. Since surface waves dominate noise records in geophysics, tomographic inversion using noise correlation techniques have been performed from Rayleigh waves so far. However, very few numerical studies implying surface waves have been conducted to confirm the extraction of the true dispersion curves from noise correlation in a complicated soil structure. In this paper, synthetic noise has been generated in a small-scale (<1 km) numerical realistic environment and classical processing techniques are applied to retrieve the phase velocity dispersion curves, first step toward an inversion. We compare results obtained from spatial autocorrelation method (SPAC), high-resolution frequency-wavenumber method (HRFK) and noise correlation slantstack techniques on a 10-sensor array. Two cases are presented in the (1–20 Hz) frequency band that corresponds to an isotropic or a directional noise wavefield. Results show that noise correlation slantstack provides very accurate phase velocity estimates of Rayleigh waves within a wider frequency band than classical techniques and is also suitable for accurately retrieving Love waves dispersion curves.  相似文献   

3.
On crustal corrections in surface wave tomography   总被引：1，自引：0，他引：1  
Mantle models from surface waves rely on good crustal corrections. We investigated how far ray theoretical and finite frequency approximations can predict crustal corrections for fundamental mode surface waves. Using a spectral element method, we calculated synthetic seismograms in transversely isotropic PREM and in the 3-D crustal model Crust2.0 on top of PREM, and measured the corresponding time-shifts as a function of period. We then applied phase corrections to the PREM seismograms using ray theory and finite frequency theory with exact local phase velocity perturbations from Crust2.0 and looked at the residual time-shifts. After crustal corrections, residuals fall within the uncertainty of measured phase velocities for periods longer than 60 and 80 s for Rayleigh and Love waves, respectively. Rayleigh and Love waves are affected in a highly non-linear way by the crustal type. Oceanic crust affects Love waves stronger, while Rayleigh waves change most in continental crust. As a consequence, we find that the imperfect crustal corrections could have a large impact on our inferences of radial anisotropy. If we want to map anisotropy correctly, we should invert simultaneously for mantle and crust. The latter can only be achieved by using perturbation theory from a good 3-D starting model, or implementing full non-linearity from a 1-D starting model.  相似文献   

4.
A new formulation for the propagation of surface waves in three-dimensionally varying media is developed in terms of modal interactions. A variety of assumptions can be made about the nature of the modal field: a single set of reference modes, a set of local modes for the structure beneath a point, or a set of local modes for a laterally varying reference structure. Each modal contribution is represented locally as a spectrum of plane waves propagating in different directions in the horizontal plane. The influence of 3-D structure is included by allowing coupling between different modal branches and propagation directions. For anisotropic models, with allowance for attenuation, the treatment leads to a set of coupled 2-D partial differential equations for the weight functions for different modal orders.
The representation of the guided wavefield requires the inclusion of a full set of modes, so that, even for isotropic models, both Love and Rayleigh modes appear as different polarization states of the modal spectrum. The coupling equations describe the interaction between the different polarizations induced by the presence of the 3-D structure.
The level of lateral variation within the 3-D model is not required to be small. Horizontal refraction or reflection of the surface wavefield can be included by allowing for transfer between modes travelling in different directions. Approximate forms of the coupled equation system can be employed when the level of heterogeneity is small, for example the coupling between the fundamental mode and higher modes can often be neglected, or forward propagation can be emphasized by restricting the interaction to a limited band of plane waves covering the expected direction of propagation.  相似文献   

5.
Summary. Surface wave behaviour in flat anisotropic structures is first illustrated by performing an exact computation on a simple two-layer model. The variational procedure of Smith & Dahlen is then used to compute the partial derivatives of surface wave phase velocities with respect to the elastic parameters in more realistic earth models. Linear relationships between the partial derivatives for a general anisotropic structure and those for a transversely isotropic structure are derived. When considering waves propagating in a fixed direction, there are only four independent derivatives for Rayleigh waves, and two for Love waves. To avoid the lack of resolution in an inverse method, we propose to use physically constrained models. These results are illustrated by using a model with hexagonal symmetry and a symmetry axis oriented either vertically or horizontally. Quasi-Love- and quasi-Rayleigh-wave partial derivatives are computed for both axis orientations. Modes up to the second overtone and periods ranging between 45 and 130 s have been considered. Finally, anomalies of phase velocity are computed in an oceanic model made of 1/6 oriented olivine crystals with horizontal or vertical preferred orientations of the a -axis.  相似文献   

6.
Array analysis is performed on surface waves recorded in the French Alps using a small‐aperture (25 km) temporary array of six broad‐band stations. The analysis shows that both Rayleigh and Love waves deviate relative to the great‐circle path. The deviations are particularly strong, up to 30°, between 20 and 40 s period. To interpret these observations, we first study the effect of large‐scale structures using ray tracing in a smooth, laterally heterogeneous model of the Earth. Second, we evaluate the local effect by considering a model for the French Alps including strong lateral heterogeneities around the array that were not taken into account in the ray tracing. By combining these two possible causes of the observed deviations, we propose an explanation for the general trend in the observed deviations. Finally, we show that by taking into account azimuthal deviations, phase velocities measured at a regional scale can be significantly improved.  相似文献   

7.
Summary. Asymptotic ray theory is applied to surface waves in a medium where the lateral variations of structure are very smooth. Using ray-centred coordinates, parabolic equations are obtained for lateral variations while vertical structural variations at a given point are specified by eigenfunctions of normal mode theory as for the laterally homogeneous case. Final results on wavefields close to a ray can be expressed by formulations similar to those for elastic body waves in 2-D laterally heterogeneous media, except that the vertical dependence is described by eigenfunctions of 'local' Love or Rayleigh waves. The transport equation is written in terms of geometrical-ray spreading, group velocity and an energy integral. For the horizontal components there are both principal and additional components to describe the curvature of rays along the surface, as in the case of elastic body waves. The vertical component is decoupled from the horizontal components. With complex parameters the solutions for the dynamic ray tracing system correspond to Gaussian beams: the amplitude distribution is bell-shaped along the direction perpendicular to the ray and the solution is regular everywhere, even at caustics. Most of the characteristics of Gaussian beams for 2-D elastic body waves are also applicable to the surface wave case. At each frequency the solution may be regarded as a set of eigenfunctions propagating over a 2-D surface according to the phase velocity mapping.  相似文献   

8.
In this study, we test the adequacy of 2-D sensitivity kernels for fundamental-mode Rayleigh waves based on the single-scattering (Born) approximation to account for the effects of heterogeneous structure on the wavefield in a regional surface wave study. The calculated phase and amplitude data using the 2-D sensitivity kernels are compared to phase and amplitude data obtained from seismic waveforms synthesized by the pseudo-spectral method for plane Rayleigh waves propagating through heterogeneous structure. We find that the kernels can accurately predict the perturbation of the wavefield even when the size of anomaly is larger than one wavelength. The only exception is a systematic bias in the amplitude within the anomaly itself due to a site response.
An inversion method of surface wave tomography based on the sensitivity kernels is developed and applied to synthesized data obtained from a numerical simulation modelling Rayleigh wave propagation over checkerboard structure. By comparing recovered images to input structure, we illustrate that the method can almost completely recover anomalies within an array of stations when the size of the anomalies is larger than or close to one wavelength of the surface waves. Surface wave amplitude contains important information about Earth structure and should be inverted together with phase data in surface wave tomography.  相似文献   

9.
We present the results of Rayleigh wave and Love wave phase velocity tomography in the western United States using ambient seismic noise observed at over 250 broad-band stations from the EarthScope/USArray Transportable Array and regional networks. All available three-component time-series for the 12-month span between 2005 November 1 and 2006 October 31 have been cross-correlated to yield estimated empirical Rayleigh and Love wave Green's functions. The Love wave signals were observed with higher average signal-to-noise ratio (SNR) than Rayleigh wave signals and hence cannot be fully explained by the scattering of Rayleigh waves. Phase velocity dispersion curves for both Rayleigh and Love waves between 5 and 40 speriod were measured for each interstation path by applying frequency–time analysis. The average uncertainty and systematic bias of the measurements are estimated using a method based on analysing thousands of nearly linearly aligned station-triplets. We find that empirical Green's functions can be estimated accurately from the negative time derivative of the symmetric component ambient noise cross-correlation without explicit knowledge of the source distribution. The average traveltime uncertainty is less than 1 s at periods shorter than 24 s. We present Rayleigh and Love wave phase speed maps at periods of 8, 12, 16,and 20 s. The maps show clear correlations with major geological structures and qualitative agreement with previous results based on Rayleigh wave group speeds.  相似文献   

10.
Summary. A parabolic approximation to the equation of motion of elastic waves as a sum of surface modes and discovering a parabolic approximation be applied directly to surface waves. The approximation depends on the material properties varying slowly within a wavelength, whereas surface waves may travel in a surface wave guide whose depth is of the same order of magnitude as a wavelength. This difficulty is overcome by representing the waves as a sum of surface modes and discovering a parabolic approximation for the amplitudes as a function of position on the surface. The theory is applicable to the propagation of Love or Rayleigh waves in a structure which is vertically stratified in an arbitrary way, but varies slowly in any horizontal direction.  相似文献   

11.
We show that most of the arguments in the above paper are either incorrect or irrelevant to the point the authors are trying to make. We show that their results have no bearing on the model proposed by our group, as they claim. They discuss the seismic response of a valley with a 2-D trapezoidal cross-section in a vertical plane, whereas we dealt with a closed basin with a 2-D cross-section but of arbitrary geometry and in the horizontal plane. Even more significantly, the width of the valley they use is much smaller than the wavelength of the horizontal P waves that can resonate, thereby precluding any possibility of them being trapped. Therefore, their arguments do not clarify the issue posed in the title of their article.  相似文献   

12.
It is well established that the Earth's uppermost mantle is anisotropic, but there are no clear observations of anisotropy in the deeper parts of the mantle. Surface waves are well suited to observe anisotropy since they carry information about both radial and azimuthal anisotropy. Fundamental mode surface waves, for commonly used periods up to 200 s, are sensitive to structure in the first few hundred kilometres, and therefore, do not provide information on anisotropy below. Higher mode surface waves have sensitivities that extend to and beyond the transition zone, and should thus give insight about azimuthal anisotropy at greater depths. We have measured higher mode Love and Rayleigh phase velocities using a model space search approach, which provides us with consistent relative uncertainties from measurement to measurement and from mode to mode. From these phase velocity measurements, we constructed global anisotropic phase velocity maps. Prior to inversion, we determine the optimum relative weighting for anisotropy. We present global azimuthal phase velocity maps for higher mode Rayleigh waves (up to the sixth higher mode) and Love waves (up to the fifth higher mode) with corresponding average model uncertainties. The anisotropy we derive is robust within the uncertainties for all modes. Given the ray theoretical sensitivity kernels of Rayleigh and Love wave modes, the source of anisotropy is complex, but mainly located in the asthenosphere and deeper. Our models show a good correspondence with other studies for the fundamental mode, but we have been able to achieve higher resolution.  相似文献   

13.
Summary. The propagation of surface waves in a laterally varying medium can be described by representing the wavetrain as a superposition of modal contributions for a reference structure. As the guided waves propagate through a heterogeneous zone the modal coefficients needed to describe the wavetrain vary with position, leading to interconversions between modes and reflection into backward travelling modes. The evolution of the modal terms may be described by a set of first-order differential equations which allow for coupling to both forward and backward travelling waves; the coefficients in these equations depend on the differences between the actual structure and the reference structure. This system is established using the orthogonality properties of the modal eigenfunctions and is valid for SH -waves, P - SV -waves and full anisotropy.
The reflected and transmitted wavefields for a region of heterogeneity can be related to the incident wave by introducing reflection and transmission matrices which connect the modal coefficients in these fields to those in the incident wavetrain. By considering a sequence of models with increasing width of heterogeneity we are able to derive a set of Ricatti equations for the reflection and transmission matrices which may be solved by initial value techniques. This avoids an awkward two-point boundary value problem for a large number of coupled equations. The method is demonstrated for 1 Hz Lg - and Sn -waves in a multilayered model for which there are 19 coupled modes.
The method is applicable to three-dimensional heterogeneity, and we are able to show that the interconversion between Love and Rayleigh waves, in the presence of gradients in seismic properties transverse to the propagation path, leads to a net rate of increase of the transverse components of the seismogram at the expense of the other components.  相似文献   

14.
The characteristics of a reflected spherical wave at a free surface are investigated by numerical methods; in particular, the polarization angles and amplitude coefficients of a reflected spherical wave are studied. The classical case of the reflection of a plane P wave from a free surface is revisited in order to establish our terminology, and the classical results are recast in a way which is more suited for the study undertaken. The polarization angle of a plane P wave, for a given angle of incidence, is shown to be 90° minus twice the angle of reflection of the reflected S wave. For a Poisson's ratio less than 1/3, there is a non-normal incident angle for which both amplification coefficients are 2 precisely; for this incident angle the direction of the particle motion at the free surface is also the direction of the incident wave. For a wave emanating from a spherical source, the polarization angle, for all angles of incidence, is always less than, or equal to, the polarization angle of a plane P wave. The vector amplification coefficient of a spherical wave, for all angles of incidence, is always greater than the vector amplification coefficient of a plane P wave. As expected, the results for a spherical wave approach the results for a plane P wave in the far field. Furthermore, there was a good agreement between the theoretical modelling and the numerical modelling using the dynamic finite element method (DFEM).  相似文献   

15.
The diffraction of P, S and Rayleigh waves by 3-D topographies in an elastic half-space is studied using a simplified indirect boundary element method (IBEM). This technique is based on the integral representation of the diffracted elastic fields in terms of single-layer boundary sources. It can be seen as a numerical realization of Huygens principle because diffracted waves are constructed at the boundaries from where they are radiated by means of boundary sources. A Fredholm integral equation of the second kind for such sources is obtained from the stress-free boundary conditions. A simplified discretization scheme for the numerical and analytical integration of the exact Green's functions, which employs circles of various sizes to cover most of the boundary surface, is used.
The incidence of elastic waves on 3-D topographical profiles is studied. We analyse the displacement amplitudes in the frequency, space and time domains. The results show that the vertical walls of a cylindrical cavity are strong diffractors producing emission of energy in all directions. In the case of a mountain and incident P, SV and SH waves the results show a great variability of the surface ground motion. These spatial variations are due to the interference between locally generated diffracted waves. A polarization analysis of the surface displacement at different locations shows that the diffracted waves are mostly surface and creeping waves.  相似文献   

16.
Summary. Analysis of NORSAR records and a number of Soviet microfilms reveals second-mode surface Caves propagating along paths covering a large part of Eurasia. These second modes in the 6–15-s period band are frequently disturbed by other surface-wave modes and by body-wave arrivals. However, in all cases, where the modes appear to be undisturbed and show normal dispersion, the Second Rayleigh modes have a slowly varying phase difference with the Second Love modes. This coupling has the particle motion of Inclined Rayleigh waves characteristic of surface-wave propagation in anisotropic media, where the anisotropy possesses a horizontal plane of symmetry. Numerical examination of surface wave propagating in Earth models, with an anisotropic layer in the upper mantle, demonstrate that comparatively small thicknesses of material with weak velocity anisotropy can produce large deviations in the polarizations of Inclined Rayleigh Second modes. In many structures, these inclinations are very sensitive to small changes in anisotropic orientation and to small changes in the surrounding isotropic structure. It is suggested that examination of second mode inclination anomalies of second mode surface waves may be a powerful technique for examining the detailed anisotropic structure of the upper mantle.  相似文献   

17.
High-frequency body waves recorded by a temporary seismic array across the surface rupture trace of the 1992 Landers, California, earthquake were used to determine fault-zone structures down to the seismogenic depth. We first developed a technique to use generalized ray theory to compute synthetic seismograms for arbitrarily oriented tabular low-velocity fault-zone models. We then generated synthetic waveform record sections of a linear array across a vertical fault zone. They show that both arrival times and waveforms of P and S waves vary systematically across the fault due to transmissions and reflections from boundaries of the low-velocity fault zone. The waveform characteristics and arrival-time patterns in the record sections allow us to locate the boundaries of the fault zone and to determine its P - and S -wave velocities independently as well as its depth extent. Therefore, the trade-off between the fault-zone width and velocities can be avoided. Applying the method to the Landers waveform data reveals a low-velocity zone with a width of 270–360 m and a 35–60 per cent reduction in P and S velocities relative to the host rock. The analysis suggests that the low-velocity zone extends to a depth of ∼7 km. The western boundary of the low-velocity zone coincides with the observed main surface rupture trace.  相似文献   

18.
Summary. Normal mode theory, extended to the slightly laterally heterogeneous earth by the first-order Born approximation, is applied to the waveform inversion of mantle Love wave (200–500 s) for the Earth's lateral heterogeneity at l = 2 and a spherically symmétric anelasticity ( Q μ) structure. The data are from the Global Digital Seismograph Network (GDSN). The l =2 pattern is very similar to the results of other studies that used either different méthods, such as phase velocity measurements and multiplet location measurements, or a different data set, such as mantle Rayleigh waves from different instruments. The results are carefully analysed for variance reduction and are most naturally explained by heterogeneity in the upper 420 km. Because of the poor resolution of the data set for the deep interior, however, a fairly large heterogeneity in the transition zones, of the order of up to 3.5 per cent in shear wave velocity, is allowed. It is noteworthy that Love waves of this period range cannot constrain the structure below 420 km and thus any model presented by similar studies below this depth are likely to be constrained by Rayleigh waves (spheroidal modes) only.
The calculated modal Q values for the obtained Q μ model fall within the error bars of the observations. The result demonstrates the discrepancy of Rayleigh wave Q and Love wave Q and indicates that care must be taken when both Rayleigh and Love wave data, including amplitude information, are inverted simultaneously.
Anomalous amplitude inversions of G2 and G3, for example, are observed for some source-receiver pairs. This is due to multipathing effects. One example near the epicentral region, which is modelled by the obtained l = 2 heterogeneity, is shown.  相似文献   

19.
When full 3-D modelling is too costly or cumbersome, computations of 3-D elastic wave propagation in laterally heterogeneous, multilayered 2-D geological structures may enhance considerably our ability to predict strong ground motion for seismological and engineering purposes. Towards this goal, we extend the method based on the combination of the thin-layer finite-element and boundary-element methods (TLFE-BEM) and calculate windowend f - k spectra of the 3-D wavefield. The windowed f - k spectra are spatially localized spectra from which the local properties of the wavefield can be extracted. The TLFE-BEM is particularly suited for calculating the complete wavefield where surface waves are dominant in multilayered media. The computations are performed in the frequency domain, providing the f - k spectra directly. From the results for the 3-D wavefield excited by a point source in a 2-D multilayered, sloped structure, it can be said that the phase velocity of the fundamental-mode Rayleigh wave in a laterally heterogeneous multilayered medium, estimated from the windowed f - k spectra, varies with the location of the point source. For the model calculated in this article, the phase velocity varies between the value for the flat layered structure of the thick-layer side and that for the structure just under the centre of the window. The exact subsurface structure just under the centre of an array in a laterally heterogeneous medium cannot be obtained if we use the f - k spectral analysis assuming a flat layered structure.  相似文献   

20.
We infer the lithospheric structure in eastern Turkey using teleseismic and regional events recorded by 29 broad-band stations from the Eastern Turkey Seismic Experiment (ETSE). We combine the surface wave group velocities (Rayleigh and Love) with telesesimic receiver functions to jointly invert for the S -wave velocity structure, Moho depth and mantle-lid (lithospheric mantle) thickness. We also estimated the transverse anisotropy due to Love and Rayleigh velocity discrepancies. We found anomalously low shear wave velocities underneath the Anatolian Plateau. Average crustal thickness is 36 km in the Arabian Plate, 44 km in Anatolian Block and 48 km in the Anatolian Plateau. We observe very low shear wave velocities at the crustal portion (30–38 km) of the northeastern part of the Anatolian Plateau. The lithospheric mantle thickness is either not thick enough to resolve it or it is completely removed underneath the Anatolian Plateau. The shear velocities and anisotropy down to 100 km depth suggest that the average lithosphere–asthenosphere boundary in the Arabian Plate is about 90 and 70 km in Anatolian block. Adding the surface waves to the receiver functions is necessary to constrain the trade-off between velocity and the thickness. We find slower velocities than with the receiver function data alone. The study reveals three different lithospheric structures in eastern Turkey: the Anatolian plateau (east of Karliova Triple Junction), the Anatolian block and the northernmost portion of the Arabian plate. The boundary of lithospheric structure differences coincides with the major tectonic boundaries.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号