共查询到20条相似文献，搜索用时 31 毫秒
1.
Terrestrial laser scanning (TLS) has been used to estimate a number of biophysical and structural vegetation parameters. Of these stem diameter is a primary input to traditional forest inventory. While many experimental studies have confirmed the potential for TLS to successfully extract stem diameter, the estimation accuracies differ strongly for these studies – due to differences in experimental design, data processing and test plot characteristics. In order to provide consistency and maximize estimation accuracy, a systematic study into the impact of these variables is required. To contribute to such an approach, 12 scans were acquired with a FARO photon 120 at two test plots (Beech, Douglas fir) to assess the effects of scan mode and circle fitting on the extraction of stem diameter and volume. An automated tree stem detection algorithm based on the range images of single scans was developed and applied to the data. Extraction of stem diameter was achieved by slicing the point cloud and fitting circles to the slices using three different algorithms (Lemen, Pratt and Taubin), resulting in diameter profiles for each detected tree. Diameter at breast height (DBH) was determined using both the single value for the diameter fitted at the nominal breast height and by a linear fit of the stem diameter vertical profile. The latter is intended to reduce the influence of outliers and errors in the ground level determination. TLS-extracted DBH was compared to tape-measured DBH. Results show that tree stems with an unobstructed view to the scanner can be successfully extracted automatically from range images of the TLS data with detection rates of 94% for Beech and 96% for Douglas fir. If occlusion of trees is accounted for stem detection rates decrease to 85% (Beech) and 84% (Douglas fir). As far as the DBH estimation is concerned, both DBH extraction methods yield estimates which agree with reference measurements, however, the linear fit based approach proved to be more robust for the single scan DBH extraction (RMSE range 1.39–1.74 cm compared to 1.47–2.43 cm). With regard to the different circle fit algorithms applied, the algorithm by Lemen showed the best overall performance (RMSE range 1.39–1.65 cm compared to 1.49–2.43 cm). The Lemen algorithm was also found to be more robust in case of noisy data. Compared to the single scans, the DBH extraction from the merged scan data proved to be superior with significant lower RMSE’s (0.66–1.21 cm). The influence of scan mode and circle fitting is reflected in the stem volume estimates, too. Stem volumes extracted from the single scans exhibit a large variability with deviations from the reference volumes ranging from −34% to 44%. By contrast volumes extracted from the merged scans only vary weakly (−2% to 6%) and show a marginal influence of circle fitting. 相似文献
2.
R. Suraj Reddy Chandra Shekhar Jha Krishnan Sundara Rajan 《Journal of the Indian Society of Remote Sensing》2018,46(6):937-943
Forest inventory parameters, primarily tree diameter and height, are required for several management and planning activities. Currently, Terrestrial Laser Scanning (TLS) is a promising technology in automated measurements of tree parameters using dense 3D point clouds. In comparison with conventional manual field inventory methods, TLS systems would supplement field data with detailed and relatively higher degree of accurate measurements and increased measurement frequency. Although, multiple scans from TLS captures more area, they are resource and time consuming to ensure proper co-registration between the scans. On the other hand, Single scans provide a fast and recording of the data but are often affected by occlusions between the trees. The current study evaluates potential of single scan TLS data to (1) develop an automatic method for tree stem identification and diameter estimation (diameter at breast height—DBH) using random sample consensus (RANSAC) based circle fitting algorithm, (2) validate using field based measurements to derive accuracy estimates and (3) assess the influence of distance to scanner on detection and measurement accuracies. Tree detection and diameter measurements were validated for 5 circular plots of 20 m radius using single scans in dry deciduous forests of Betul, Madhya Pradesh. An overall tree detection accuracy of 85 and 70% was observed in the scanner range of 15 and 20 m respectively. The tree detection accuracies decreased with increased distance to the scanner due to the decrease in visible area. Also, estimated stem diameter using TLS was found to be in agreement with the field measured diameter (R2 = 0.97). The RMSE of estimated DBH was found to be 3.5 cm (relative RMSE ~20%) over 202 trees detected over 5 plots. Results suggest that single scan approach suffices the cause of accuracy, reducing uncertainty and adds to increased sampling frequency in forest inventory and also implies that TLS has a seemingly high potential in forest management. 相似文献
3.
This study compares the accuracies of diameter at breast height (DBH) estimations by three initial (minimum bounding box, centroid, and maximum distance) and two refining (Monte Carlo and optimal circle) circle-fitting methods The circle-fitting algorithms were evaluated in multi-scan mode and a simulated single-scan mode on 157 European beech trees (Fagus sylvatica L.). DBH measured by a calliper was used as reference data. Most of the studied circle-fitting algorithms significantly underestimated the mean DBH in both scanning modes. Only the Monte Carlo method in the single-scan mode significantly overestimated the mean DBH. The centroid method proved to be the least suitable and showed significantly different results from the other circle-fitting methods in both scanning modes. In multi-scan mode, the accuracy of the minimum bounding box method was not significantly different from the accuracies of the refining methods The accuracy of the maximum distance method was significantly different from the accuracies of the refining methods in both scanning modes. The accuracy of the Monte Carlo method was significantly different from the accuracy of the optimal circle method in only single-scan mode. The optimal circle method proved to be the most accurate circle-fitting method for DBH estimation from point clouds in both scanning modes. 相似文献
4.
Diameter distribution is essential for calculating stem volume and timber assortments of forest stands. A new method was proposed in this study to improve the estimation of stem volume and timber assortments, by means of combining the Area-based approach (ABA) and individual tree detection (ITD), the two main approaches to deriving forest attributes from airborne laser scanning (ALS) data. Two methods, replacement, and histogram matching were employed to calibrate ABA-derived diameter distributions with ITD-derived diameter estimates at plot level. The results showed that more accurate estimates were obtained when calibrations were applied. In view of the highest accuracy between ABA and ITD, calibrated diameter distributions decreased its relative RMSE of the estimated entire growing stock, saw log and pulpwood fractions by 2.81%, 3.05% and 7.73% points at best, respectively. Calibration improved pulpwood fraction significantly, which contributed to the negligible bias of the estimated entire growing stock. 相似文献
5.
Site productivity is essential information for sustainable forest management and site index (SI) is the most common quantitative measure of it. The SI is usually determined for individual tree species based on tree height and the age of the 100 largest trees per hectare according to stem diameter. The present study aimed to demonstrate and validate a methodology for the determination of SI using remotely sensed data, in particular fused airborne laser scanning (ALS) and airborne hyperspectral data in a forest site in Norway. The applied approach was based on individual tree crown (ITC) delineation: tree species, tree height, diameter at breast height (DBH), and age were modelled and predicted at ITC level using 10-fold cross validation. Four dominant ITCs per 400 m2 plot were selected as input to predict SI at plot level for Norway spruce (Picea abies (L.) Karst.) and Scots pine (Pinus sylvestris L.). We applied an experimental setup with different subsets of dominant ITCs with different combinations of attributes (predicted or field-derived) for SI predictions. The results revealed that the selection of the dominant ITCs based on the largest DBH independent of tree species, predicted the SI with similar accuracy as ITCs matched with field-derived dominant trees (RMSE: 27.6% vs 23.3%). The SI accuracies were at the same level when dominant species were determined from the remotely sensed or field data (RMSE: 27.6% vs 27.8%). However, when the predicted tree age was used the SI accuracy decreased compared to field-derived age (RMSE: 27.6% vs 7.6%). In general, SI was overpredicted for both tree species in the mature forest, while there was an underprediction in the young forest. In conclusion, the proposed approach for SI determination based on ITC delineation and a combination of ALS and hyperspectral data is an efficient and stable procedure, which has the potential to predict SI in forest areas at various spatial scales and additionally to improve existing SI maps in Norway. 相似文献
6.
Impervious surface is an important environmental and socio-economic indicator for numerous urban studies. While a large number of researches have been conducted to estimate the area and distribution of impervious surface from satellite data, the accuracy for impervious surface estimation (ISE) is insufficient due to high diversity of urban land cover types. This study evaluated the use of panchromatic (PAN) data in very high resolution satellite image for improving the accuracy of ISE by various pan-sharpening approaches, with a further comprehensive analysis of its scale effects. Three benchmark pan-sharpening approaches, Gram-Schmidt (GS), PANSHARP and principal component analysis (PCA) were applied to WorldView-2 in three spots of Hong Kong. The on-screen digitization were carried out based on Google Map and the results were viewed as referenced impervious surfaces. The referenced impervious surfaces and the ISE results were then re-scaled to various spatial resolutions to obtain the percentage of impervious surfaces. The correlation coefficient (CC) and root mean square error (RMSE) were adopted as the quantitative indicator to assess the accuracy. The accuracy differences between three research areas were further illustrated by the average local variance (ALV) which was used for landscape pattern analysis. The experimental results suggested that 1) three research regions have various landscape patterns; 2) ISE accuracy extracted from pan-sharpened data was better than ISE from original multispectral (MS) data; and 3) this improvement has a noticeable scale effects with various resolutions. The improvement was reduced slightly as the resolution became coarser. 相似文献
7.
陆地总初级生产力遥感估算精度分析 总被引：1，自引：0，他引：1
准确估算陆地总初级生产力GPP(Gross Primary Productivity)数值对碳循环过程模拟有重要影响。本文介绍了多种基于植被指数以及基于光能利用率的遥感GPP算法,综述了不同算法在其研究区域的估算精度;并分析了MODIS/GPP以及BESS/GPP两种遥感GPP产品在不同植被类型的估算精度。通过对比全球碳通量站网络GPP数据表明,MODIS/GPP产品在全球估算结果具显著相关性(R2=0.59)及中等标准误差(RMSE=2.86 g C/m2/day),估算精度较高的植被类型有落叶阔叶林,草地等;估算精度较低类型包括常绿阔叶林,稀树草原等。本文对GPP产品中存在的不确定性进行分析,通过综述前人研究中发现的遥感估算GPP方法中存在的问题,指出可能的提高卫星遥感GPP产品估算精度的方法及发展趋势。 相似文献
8.
Recent research results have shown that the performance of digital surface model extraction using novel high-quality photogrammetric images and image matching is a highly competitive alternative to laser scanning. In this article, we proceed to compare the performance of these two methods in the estimation of plot-level forest variables. Dense point clouds extracted from aerial frame images were used to estimate the plot-level forest variables needed in a forest inventory covering 89 plots. We analyzed images with 60% and 80% forward overlaps and used test plots with off-nadir angles of between 0° and 20°. When compared to reference ground measurements, the airborne laser scanning (ALS) data proved to be the most accurate: it yielded root mean square error (RMSE) values of 6.55% for mean height, 11.42% for mean diameter, and 20.72% for volume. When we applied a forward overlap of 80%, the corresponding results from aerial images were 6.77% for mean height, 12.00% for mean diameter, and 22.62% for volume. A forward overlap of 60% resulted in slightly deteriorated RMSE values of 7.55% for mean height, 12.20% for mean diameter, and 22.77% for volume. According to our results, the use of higher forward overlap produced only slightly better results in the estimation of these forest variables. Additionally, we found that the estimation accuracy was not significantly impacted by the increase in the off-nadir angle. Our results confirmed that digital aerial photographs were about as accurate as ALS in forest resources estimation as long as a terrain model was available. 相似文献
9.
Predicting individual tree attributes from airborne laser point clouds based on the random forests technique 总被引：2，自引：0，他引：2
This paper depicts an approach for predicting individual tree attributes, i.e., tree height, diameter at breast height (DBH) and stem volume, based on both physical and statistical features derived from airborne laser-scanning data utilizing a new detection method for finding individual trees together with random forests as an estimation method. The random forests (also called regression forests) technique is a nonparametric regression method consisting of a set of individual regression trees. Tests of the method were performed, using 1476 trees in a boreal forest area in southern Finland and laser data with a density of 2.6 points per m2. Correlation coefficients (R) between the observed and predicted values of 0.93, 0.79 and 0.87 for individual tree height, DBH and stem volume, respectively, were achieved, based on 26 laser-derived features. The corresponding relative root-mean-squared errors (RMSEs) were 10.03%, 21.35% and 45.77% (38% in best cases), which are similar to those obtained with the linear regression method, with maximum laser heights, laser-estimated DBH or crown diameters as predictors. With random forests, however, the forest models currently used for deriving the tree attributes are not needed. Based on the results, we conclude that the method is capable of providing a stable and consistent solution for determining individual tree attributes using small-footprint laser data. 相似文献
10.
An empirical study was performed assessing the accuracy of land use change detection when using satellite image data acquired ten years apart by sensors with differing spatial resolutions. Landsat/Multi‐spectral Scanner (MSS) with Landsat/Thematic Mapper (TM) or SPOT/High Resolution Visible (HRV) multi‐spectral (XS) data were used as a multi‐data pair for detecting land use change. The primary objectives of the study were to: (1) compare standard change detection methods (e.g. multi‐date ratioing and principal components analysis) applied to image data of varying spatial resolution; (2) assess whether to transform the raster grid of the higher resolution image data to that of the lower resolution raster grid or vice‐versa in the registration process: and (3) determine if Landsat/TM or SPOT/ HRV(XS) data provides more accurate detection of land use changes when registered to historical Landsat/MSS data. Ratioing multi‐sensor, multi‐date satellite image data produced higher change detection accuracies than did principal components analysis and is useful as a land use change enhancement technique. Ratioing red and near infrared bands of a Landsat/MSS‐SPOT/HRV(XS) multi‐date pair produced substantially higher change detection accuracies (～10%) than ratioing similar bands of a Landsat/MSS ‐ Landsat/TM multi‐data pair. Using a higher‐resolution raster grid of 20 meters when registering Landsat/MSS and SPOTZHRV(XS) images produced a slightly higher change detection accuracy than when both images were registered to an 80 meter raster grid. Applying a “majority”; moving window filter whose size approximated a minimum mapping unit of 1 hectare increased change detection accuracies by 1–3% and reduced commission errors by 10–25%. 相似文献
11.
Zhengyang Hou Qing Xu Timo Tokola 《ISPRS Journal of Photogrammetry and Remote Sensing》2011,66(6):776-786
In this study, the potential of remote sensing in tropical forests is examined in relation to the diversification of sensors. We report here on the comparison of alternative methods that use multisource data from Airborne Laser Scanning (ALS), Airborne CIR and ALOS AVNIR-2 to estimate stem volume and basal area, in Laos. Multivariate linear regression analyses with stepwise selection of predictors were implemented for modelling. The predictors of ALS metrics were calculated by means of the canopy height distribution approach, while predictors from both spectral and textual features were respectively generated for Airborne CIR and ALOS AVNIR-2 data. With respect to the estimation capacity from individual data sources after leave-one-out cross-validation, the ALS data proved superior, with the lowest RMSE of 36.92% for stem volume and 47.35% for basal area, whereas Airborne CIR and ALOS AVNIR-2 remained at similar accuracy levels, but fell well behind the ALS data. By integrating ALS metrics with other predictors from Airborne CIR or ALOS AVNIR-2, hybrid modelling was further tested respectively. The results showed that only the hybrid model for stem volume involving ALS and Airborne CIR improved the accuracy of 1.9% in terms of relative RMSE than that of using ALS alone. 相似文献
12.
Measuring tree stem diameters using intensity profiles from ground-based scanning lidar from a fixed viewpoint 总被引：1，自引：0，他引：1
This paper presents a method for using the intensity of returns from a scanning light detection and ranging (lidar) system from a single viewing point to identify the location and measure the diameter of tree stems within a forest. Such instruments are being used for rapid forest inventory and to provide consistent supporting information for airborne lidars. The intensity transect across a tree stem is found to be consistent with a simple model parameterised by the range and diameter of the trunk. The stem diameter is calculated by fitting the model to transect data. The angular span of the stem can also be estimated by using a simple threshold where intensity values are tested against the expected intensity for a stem of given diameter. This is useful when data are insufficient to fit the model or the stem is partially obscured. The process of identifying tree positions and trunk diameters is fully automated and is shown to be successful in identifying a high proportion of trees, including some that are partially obscured from view. The range and bearing to trees are in excellent agreement with field data. Trunk angular span and diameter estimations are well correlated with field measurements at the plot scale. The accuracy of diameter estimation is found to decrease with range from the scanning position and is also reduced for stems subtending small angles (less than twice the scanning resolution) to the instrument. A method for adjusting survey results to compensate for trees missed due to obscuration from the scanning point and the use of angle count methods is found to improve basal area estimates and achieve agreement within 4% of field measurements. 相似文献
13.
由于地面三维激光扫描仪扫描精度对扫描距离、扫描分辨率及扫描方向具有很强的依赖性,因此研究其与扫描距离、扫描分辨率及扫描方向的关系对实验分析及工程应用具有很重要的意义。本文利用Faro Focus 3 D激光扫描仪从不同距离、扫描分辨率、扫描方向对不同形状的平面标靶进行实验,研究不同的扫描方式对平面标靶拟合精度的影响,并进一步判断扫描仪是否存在较大的轴系误差,为后期的自检校提供依据。 相似文献
14.
用地基激光雷达提取单木结构参数——以白皮松为例 总被引：6，自引：1，他引：5
以白皮松(Pinus bungeana Zucc)为研究对象,针对地基激光雷达TLS扫描的3维点云数据在单株木垂直方向的分布特征,提出了一种基于体元化方法的树干覆盖度变化检测方法,获取单木枝下高;然后根据获取的枝下高引入2维凸包算法获取垂直方向分层树冠轮廓,并计算树冠体积和冠幅;同时获取的单木参数还有胸径与树高。结果表明:单木枝下高的估测精度较高,R2与RMSE分别为0.97 m和0.21 m;胸径估测结果的R2与RMSE分别为0.79 cm和1.07 cm;采用逐步线性回归方法建立单木树冠体积与其他单木参数的相关关系,模型变量包括冠幅、叶子填充树冠长度和胸径,样本数为20,模型的R2与RMSE分别是0.967 m3和2.64 m3。本文方法能较准确地估测枝下高,TLS数据具有对树冠结构3维建模的潜力。 相似文献
15.
Land cover classification of finer resolution remote sensing data is always difficult to acquire high-frequency time series data which contains temporal features for improving classification accuracy. This paper proposed a method of land cover classification with finer resolution remote sensing data integrating temporal features extracted from time series coarser resolution data. The coarser resolution vegetation index data is first fused with finer resolution data to obtain time series finer resolution data. Temporal features are extracted from the fused data and added to improve classification accuracy. The result indicates that temporal features extracted from coarser resolution data have significant effect on improving classification accuracy of finer resolution data, especially for vegetation types. The overall classification accuracy is significantly improved approximately 4% from 90.4% to 94.6% and 89.0% to 93.7% for using Landsat 8 and Landsat 5 data, respectively. The user and producer accuracies for all land cover types have been improved. 相似文献
16.
The results of modeling the procedure of synthesizing data from an imaging spectrometer (IS) and a multispectral scanner (MSS) with low and high spatial resolutions, respectively, are presented. The synthesis method makes it possible to develop a classification and determine the spatial distribution of the sensed features at the high spatial resolution of MSS imagery and to retrieve their spectra with the spectroradiometric detail of IS measurements. It is shown that with an IS signal-to-noise ratio of no less than 50, a geometric matching of IS and MSS data with an accuracy of no less than 0.1 of an IS pixel along both axes, and with allowance for the IS real point-spread function, the spectral nonuniformity of the classes and the errors in retrieving the spectra fall within the range of several percentage points, with a ratio of the IS and MSS spatial resolutions of 4-8 and ～10% with a ratio of resolutions of 16-32. 相似文献
17.
18.
The effect of soil moisture content on vegetation and therefore on growth is well known. Information about the growth of forest stands is key in forest planning and management, and is the concern of various stakeholders. One way to assess moisture content and its impacts on forest growth is to apply the Topographic Wetness Index (TWI) and the derived terrain attributes from the Digital Terrain Model (DTM). The TWI is an important terrain attribute, used in various ecological studies. In the current study, a total of 9987 tally trees within 197 sample plots in southeastern Finland and LiDAR (Light Detection and Ranging) −based TWI were selected to examine: 1) the effect of cell resolutions and focal statistics of neighborhood cells of DTM, on tree diameter increment, and 2) possibilities to improve the prediction accuracy of an existing single-tree growth model using the terrain attributes and TWI with the combined effects of three characteristics (i.e., cell resolutions, neighborhood cells and terrain attributes). The results suggest that the TWI with terrain attributes improved the growth estimation significantly, and within different site types the Root Mean Square Errors (RMSE) were lowered substantially. The best results were obtained for birch trees. The higher resolution of the DTM and the lower focal neighborhood cells were found to be the best alternative in computing the TWI. 相似文献
19.
Forest plantations are an important source of terrestrial carbon sequestration. The forest of Robinia pseudoacacia in the Yellow River Delta (YRD) is the largest artificial ecological protection forest in China. However, more than half of the forest has appeared different degrees of dieback and even death since the 1990s. Timely and accurate estimation of the forest aboveground biomass (AGB) is a basis for studying the carbon cycle of forests. Light Detecting and Ranging (LiDAR) has been proved to be one of the most powerful methods for forest biomass estimation. However, because of an irregular and overlapping shape of the broadleaved forest canopy in a growing season, it is difficult to segment individual trees and estimate the tree biomass from airborne LiDAR data. In this study, a new method was proposed to solve this problem of individual tree detection in the Robinia pseudoacacia forest based on a combination of the Unmanned Aerial Vehicle-Light Detecting and Ranging (UAV-LiDAR) with the Backpack-LiDAR. The proposed method mainly consists of following steps: (i) at a plot level, trees in the UAV-LiDAR data were detected by seed points obtained by an individual tree segmentation (ITS) method from the Backpack-LiDAR data; (ii) height and diameter at breast height (DBH) of an individual tree would be extracted from UAV and Backpack LiDAR data, respectively; (iii) the individual tree AGB would be calculated through an allometric equation and the forest AGB at the plot level was accumulated; and (iv) the plot-level forest AGB was taken as a dependent variable, and various metrics extracted from UAV-LiDAR point cloud data as independent variables to estimate forest AGB distribution in the study area by using both multiple linear regression (MLR) and random forest (RF) models. The results demonstrate that: (1) the seed points extracted from Backpack-LiDAR could significantly improve the overall accuracy of individual tree detection (F = 0.99), and thus increase the forest AGB estimation accuracy; (2) compared with MLR model, the RF model led to a higher estimation accuracy (p < 0.05); and (3) LiDAR intensity information selected by both MLR and RF models and laser penetration rate (LP) played an important role in estimating healthy forest AGB. 相似文献
20.
Environmental factors influence the accuracy in stem volume retrieval using European Remote Sensing Satellite (ERS) tandem synthetic aperture radar (SAR) interferometry. Some forest stands are more sensitive than others to heterogeneity of environmental properties, forest properties, and noise. It is shown that the consistency of coherence observations between different image pairs or the consistency of the estimated stem volume can be used to sort forest stands according to increasing errors in stem volume estimates associated with varying forest properties. Fifteen ERS tandem pairs were used to determine the relative root mean square error (RMSE) of stem volume estimated from C-band SAR interferometry. The test site, Tuusula in Finland, contains 210 forest stands with stem volumes up to 539 m3/ha. RMSE varies between 17% and 63% depending on number and type of stands included in the retrieval accuracy analysis. The more homogeneous forest stands with larger area and higher stem volumes of spruce and pine are those with highest retrieval accuracy 相似文献