Geological controls on rock mass classification of coal from Huntly East Mine, New Zealand     

Vicki Moon  Trisha Roy 《Engineering Geology》2004,75(2):201-213

Rock Mass Rating (RMR) measurements from 65 sites within Huntly East underground coal mine are presented. All measurements are in coal, for which the dominant discontinuities are vertical cleat. Basic RMR values using two discontinuity spacings are presented: overall RMR based on the average spacing of all individual discontinuities; and cleat zone RMR based on the average spacing between zones of cleat. Cleat orientations are highly variable, but on average approximately parallel horizontal stress axes (face cleat follows maximum horizontal stress axis, butt cleat follows minimum horizontal stress axis).Contours of RMR variations throughout the mine are used to compare rock mass conditions with geological structure. It is apparent that: (1) RMR is least within downthrown fault blocks, and particularly immediately on the downthrown sides of faults, and greatest in upthrown fault blocks; and (2) RMR contours parallel horizontal stress axes within fault-bounded blocks, and bend to parallel faults at block boundaries. From similar contours for parameters contributing to RMR, the Rock Quality Designation (RQD), groundwater rating, and discontinuity condition rating create most of the observed variations in RMR. RQD is determined from the measured discontinuity frequency and hence is a measure of the degree of fracturing of the rock mass. This is interpreted as influencing the groundwater and condition parameters directly by allowing greater water ingress. Discontinuity frequency is greatest (least spacing) in the immediate vicinity of faults, and in downthrown fault blocks, generating low RMR values. Within fault blocks RQD varies little, so RMR contours align with cleat orientations.As RMR contours, faults, stress field and cleat orientation are clearly interrelated, there is unequivocally a connection between RMR and structural geology; this allows some predictive capacity in terms of ground conditions. If geological features can be accurately defined through either drilling programs or seismic surveys, then ground conditions may be predicted before panels are driven.  相似文献   

Magnetic fabrics and rock magnetism of Proterozoic dike swarm from the southern São Francisco Craton, Minas Gerais State, Brazil     

Maria Irene Bartolomeu Raposo  Alexandre O. Chaves  Paulo Lojkasek-Lima  Manoel Souza D'Agrella-Filho  Wilson Teixeira   《Tectonophysics》2004,378(1-2):43-63

Magnetic fabric and rock magnetism studies were performed on 32 mafic dikes of a Proterozoic dike swarm from the southern São Francisco Craton (SFC; Minas Gerais State, SE Brazil). Magnetic anisotropies were determined by applying anisotropy of low-field magnetic susceptibility (AMS) and anisotropy of remanent magnetization (ARM). The latter was performed imposing both anhysteretic (total (AAR) and partial pAAR)) and isothermal remanence magnetizations (AIRM). Partial anhysteretic remanence anisotropy was performed based on remanent coercivity spectra from a pilot specimen of each site. In most sites, AMS is dominantly carried by ferromagnetic minerals, however, in some sites, the paramagnetic contribution exceeds 70% of bulk susceptibility. Rock magnetism and thin section analysis allow classifying the dikes as non-hydrothermalized and hydrothermalized. Magnetic measurement shows that the mean magnetic susceptibility is usually lower than 5×10⁻³ (SI). Ti-poor titanomagnetites up to pure magnetite pseudo-single-domain (PSD) grain sizes carry the majority of magnetic fabrics for non-hydrothermalized dikes whereas coarse to fine grained Ti-poor titanomagnetites carry the majority of magnetic fabrics for hydrothermalized dikes.Three primary AMS fabrics are recognized which are coaxial with ARM fabric, except for two dikes, from both non-hydrothermalized and hydrothermalized dikes. Normal AMS fabric surprisingly is not dominant (31%). The parallelism between AMS, pAAR_0–30, pAAR_30–60 and pAAR_60–90 fabrics in the hydrothermalized dikes indicates that magnetic grains formed due to late-stage crystallization or to remobilization of iron oxides due to hydrothermal alteration after dike emplacement have acquired a mimetic fabric coaxial with the primary fabric given by coarse-grained early crystallized Ti-poor titanomagnetites. This fabric is interpreted as magma flow in which the analysis of K_max inclination permitted the inference that the dikes were fed by horizontal or subhorizontal fluxes (K_max<30°). Intermediate AMS fabric is the most important (41%) in the investigated swarm. It is interpreted as due to vertical compaction of a static magma column with the minimum stress along the dike strike. ARM determinations for these sites also remained intermediate except for two dikes. In one of them, AIRM fabric resulted in normal AMS fabric while for the other AAR fabric resulted in inverse AMS fabric. A combination of AMS and ARM fabrics suggest that magmatic fabric for both dikes were overprinted by some late local event, probably related to Brasiliano orogenic processes after dike emplacement. InverseInverse AMS fabric is a minority (four dikes). ARM determinations also remained inverse suggesting a primary origin for inverse AMS fabric.  相似文献   

Analysis of earth dams affected by the 2001 Bhuj Earthquake   总被引：3，自引：0，他引：3  

Raghvendra Singh  Debasis Roy  Sudhir K. Jain   《Engineering Geology》2005,80(3-4):282-291

An earthquake of magnitude of 7.6 (M_w 7.6) occurred in Bhuj, India on January 26, 2001. This event inflicted damages of varying extents to a large number of small to moderate size multi-zone earth dams in the vicinity of the epicenter. Some of the distress was due to the liquefaction of saturated alluvium in foundation. Liquefaction was relatively localized for the majority of these dams because the earthquake struck in the middle of a prolonged dry season when the reservoirs behind these dams were nearly empty and shallow alluvium soils underneath the downstream portions of the dams were partly dry. Otherwise, liquefaction of foundation soils would have been more extensive and damage to these dams more significant. Six such dams have been examined in this paper. Four of these facilities, Chang, Shivlakha, Suvi, and Tapar were within the 50 km of epicenter region. These dams underwent free-field ground motion with peak ground accelerations between 0.28g to 0.52g. Of these Chang Dam underwent severe slumping, whereas Shivlakha, Suvi, and Tapar Dams were affected severely especially over the upstream sections. Fatehgadh Dam and Kaswati Dam were affected relatively less severely. Foundation conditions underneath these dams were first examined for assessing liquefaction potential. A limited amount of subsurface information available from investigations undertaken prior to the earthquake indicates that, although the foundation soils within the top 2.0 to 2.5 m underneath these dams were susceptible to liquefaction, Bhuj Earthquake did not trigger liquefaction because of lack of saturation of these layers underneath the downstream portions of these dams. These dams were then analyzed using a simple sliding block procedure using appropriate estimates of undrained soil strength parameters. The results of this analysis for these structures were found to be in general agreement with the observed deformation patterns.  相似文献   

Riddle of arsenic in groundwater of Bengal Delta Plain—role of non-inland source and redox traps     

D. Chatterjee  R. K. Roy  B. B. Basu 《Environmental Geology》2005,49(2):188-206

In the Bengal Delta Plain (BDP) the primary arsenic sourcing appears to be different from the global scenario. Here, the Terminal Pleistocene–Holocene depositional platform, the interactive early Holocene depositional morphology with fluvio-estuarine and marine incursions played a crucial role for arsenic sourcing and enrichment. The lenticular silt-fine sand layer between anoxic clay beds favoured entrapment of dissolved organic carbon with decayed phyto-planktons debris. The Terminal Pleistocene–Holocene transgression and regression processes may have acted as major events in the BDP. Interestingly, at the end of the last glacial maxima, the Pleistocene delta had undergone block movements, wherein some parts of the platform were raised above the level of Holocene deposition. Those blocks were found to be free from arsenic in the groundwater. The sea, during re-emerging inundation (10–7 ka BP), has witnessed a monsoon-induced environment in the BDP with the resultant oscillation of sea level leading to higher upsurge towards the north. This might have resulted in the marine incursion and inundation in pre-existing land depressions. Meanwhile arsenic entrapments through marine incursion as well as enrichment in the presence of organic carbon/DOC and/or Fe/Mn/Al catalytic agents could have developed into localised redox traps. It may be of relevance that due to the repetitive transgressive–regressive phases in Holocene, resulting in periodic exposure and weathering of iron-bearing minerals and consequent iron enrichment in the aquifer system. The iron, thus present, had free charge to host arsenic as a sink. It appears that arsenic, wherever found, would likely be of atypical localised exhaustible phenomenon, both in horizontal and vertical context. It also rationalises the cause of the absence of arsenic in the other nearby Pleistocene platform, which has not come across Holocene interaction and marine incursion, as to the likely limiting condition for the search for arsenic in the BDP or beyond.  相似文献   

Kimberlite petrogenesis: Insights from clinopyroxene-melt partitioning experiments at 6 GPa in the CaO-MgO-Al₂O₃-SiO₂-CO₂ system     

Shantanu Keshav  Alexandre Corgne  Michael Bizimis  Yingwei Fei 《Geochimica et cosmochimica acta》2005,69(11):2829-2845

In this experimental study, we examine the mineral-melt partitioning of major and trace elements between clinopyroxene and CO₂-rich kimberlitic melts at a pressure of 6 GPa and temperatures of 1410°C and 1430°C. The melts produced contain ∼ 28 wt% dissolved CO₂, and are saturated with olivine and clinopyroxene. To assess the effects of temperature, crystal and melt compositions on trace element partitioning, experiments were performed in the model CaO-MgO-Al₂O₃-SiO₂-CO₂ system. Our results reveal that all the elements studied, except Al, Mg, Si, and Ga, are incompatible in clinopyroxene. Partition coefficients show a considerable range in magnitude, from ∼ 10⁻³ for D_U and D_Ba to ∼ 2.5 for D_Si. The two experimental runs show similar overall partitioning patterns with the D values being lower at 1430°C. Rare earth elements display a wide range of partition coefficients, D_La (0.012-0.026) being approximately one order of magnitude lower than D_Lu (0.18-0.23). Partition coefficients for the 2+ and 3+ cations entering the M2-site exhibit a near-parabolic dependence on radius of the incorporated cations as predicted from the lattice strain model. This underlines the contribution made by the crystal structure toward controlling the distribution of trace elements. Using data obtained in this study combined with that in the published literature, we also discuss the effects that other important parameters, namely, melt composition, pressure, and temperature, could have on partitioning.Our partition coefficients have been used to model the generation of the Group I (GI) kimberlites from South Africa. The numerical modeling shows that kimberlitic melts can be produced by ∼0.5% melting of a MORB-type depleted source that has been enriched by small-degree melts originating from a similar depleted source. This result suggests that the source of GI kimberlites may be located at the lithosphere-asthenosphere transition. Percolation of small degree melts from the asthenosphere would essentially create a metasomatic horizon near the bottom of the non-convecting sublithospheric mantle. Accumulation of such small degree melts together with the presence of volatiles and conductive heating would trigger melting of the ambient mantle and subsequently lead to eruption of kimberlitic melts. Additionally, our model shows that the GI source can be generated by metasomatism of a 2 Ga old MORB source ca. 1 Ga ago. Assuming that MORB-type mantle is the most depleted source of magmas on earth, then this is the oldest age at which the GI source could have existed. However, this age most likely reflects the average age of a series of metasomatic events than that of a single event.  相似文献   

An Eocene/Oligocene blueschist‐/greenschist facies P–T loop from the Cycladic Blueschist Unit on Naxos Island,Greece: Deformation‐related re‐equilibration vs. thermal relaxation          下载免费PDF全文

Alexandre Peillod  Uwe Ring  Johannes Glodny  Alasdair Skelton 《Journal of Metamorphic Geology》2017,35(7):805-830

Geothermobarometric and geochronological work indicates a complete Eocene/early Oligocene blueschist/greenschist facies metamorphic cycle of the Cycladic Blueschist Unit on Naxos Island in the Aegean Sea region. Using the average pressure–temperature (P–T) method of thermocalc coupled with detailed textural work, we separate an early blueschist facies event at 576 ± 16 to 619 ± 32°C and 15.5 ± 0.5 to 16.3 ± 0.9 kbar from a subsequent greenschist facies overprint at 384 ± 30°C and 3.8 ± 1.1 kbar. Multi‐mineral Rb–Sr isochron dating yields crystallization ages for near peak‐pressure blueschist facies assemblages between 40.5 ± 1.0 and 38.3 ± 0.5 Ma. The greenschist facies overprint commonly did not result in complete resetting of age signatures. Maximum ages for the end of greenschist facies reworking, obtained from disequilibrium patterns, cluster near c. 32 Ma, with one sample showing rejuvenation at c. 27 Ma. We conclude that the high‐P rocks from south Naxos were exhumed to upper mid‐crustal levels in the late Eocene and early Oligocene at rates of 7.4 ± 4.6 km/Ma, completing a full blueschist‐/greenschist facies metamorphic cycle soon after subduction within c. 8 Ma. The greenschist facies overprint of the blueschist facies rocks from south Naxos resulted from rapid exhumation and associated deformation/fluid‐controlled metamorphic re‐equilibration, and is unrelated to the strong high‐T metamorphism associated with the Miocene formation of the Naxos migmatite dome. It follows that the Miocene thermal overprint had no impact on rock textures or Sr isotopic signatures, and that the rocks of south Naxos underwent three metamorphic events, one more than hitherto envisaged.  相似文献   

Numerical simulation of percussive drilling          下载免费PDF全文

Alexandre Depouhon  Vincent Denoël  Emmanuel Detournay 《国际地质力学数值与分析法杂志》2015,39(8):889-912

This paper presents a novel dynamical model to analyze the long‐term response of a percussive drilling system. This departs from existing approaches that usually consider a single activation and bit/rock interaction cycle for the analysis of the process performance. The proposed model integrates the axial dynamics of an elastic piston and an elastic drill bit, a motion‐dependent pressure law to drive the piston, and a generalized bit/rock interaction law representative of the dynamic indentation taking place at the bit/rock interface. It applies to down‐the‐hole percussive drilling as well as top‐hole, with minor modifications. The model does not account for the angular motion or the hole cleaning, however. The model is first formulated mathematically; then, a finite‐dimensional approximation is proposed for computations. Numerical analyses of the model response, for a low‐size down‐the‐hole percussive system, follow. The period‐1 stationary response for the reference configuration is studied in detail, and parametric analyses assessing the influence on the rate of penetration of the bit/rock interaction parameters, the feed force, and the percussive activation parameters are conducted. These analyses reveal that the multiscale nature of the process is well captured by the model and recover expected trends for the influence of the parameters. They also suggest that a significant increase of the penetration rate can be achieved by increasing the percussive frequency. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

Structural Control on Occurrence and Dynamics of Coalmine Fires in Jharia Coalfield: A Remote Sensing Based Analysis     

Priyom Roy  Arindam Guha  K. Vinod Kumar 《Journal of the Indian Society of Remote Sensing》2015,43(4):779-786

  相似文献   

A methodology for regionalizing 3‐D effective porosity at watershed scale in crystalline aquifers          下载免费PDF全文

Benoît Dewandel  Yvan Caballero  Jérôme Perrin  Alexandre Boisson  Fabrice Dazin  Sylvain Ferrant  Subash Chandra  Jean‐Christophe Maréchal 《水文研究》2017,31(12):2277-2295

An innovative approach for regionalizing the 3‐D effective porosity field is presented and applied to two large, overexploited, and deeply weathered crystalline aquifers located in southern India. The method derives from earlier work on regionalizing a 2‐D effective porosity field in that part of an aquifer where the water table fluctuates, which is now extended over the entire aquifer using a 3‐D approach. A method based on geological and geophysical surveys has also been developed for mapping the weathering profile layers (saprolite and fractured layers). The method for regionalizing 3‐D effective porosity combines water table fluctuation and groundwater budget techniques at various cell sizes with the use of satellite‐based data (for groundwater abstraction), the structure of the weathering profile, and geostatistical techniques. The approach is presented in detail for the Kudaliar watershed (983 km²) and tested on the 730 km² Anantapur watershed. At watershed scale, the effective porosity of the aquifer ranges from 0.5% to 2% in Kudaliar and between 0.3% and 1% in Anantapur, which agrees with earlier works. Results show that (a) depending on the geology and on the structure of the weathering profile, the vertical distribution of effective porosity can be very different and that the fractured layers in crystalline aquifers are not necessarily characterized by a rapid decrease in effective porosity and (b) that the lateral variations in effective porosity can be larger than the vertical ones. These variations suggest that within a same weathering profile, the density of open fractures and/or degree of weathering in the fractured zone may significantly vary from a place to another. The proposed method provides information on the spatial distribution of effective porosity that is of prime interest in terms of flux and contaminant transport in crystalline aquifers. Implications for mapping groundwater storage and scarcity are also discussed, which should help in improving groundwater resource management strategies.  相似文献   

Zircon fission‐track ages from Newfoundland—A proxy for high geothermal gradients and exhumation before opening of the Central Atlantic Ocean     

Arne P. Willner  Stuart N. Thomson  Johannes Glodny  Hans‐Joachim Massonne  Rolf L. Romer  Cees R. van Staal  Alexandre Zagorevski 《地学学报》2019,31(1):1-10

Following Appalachian orogenesis, metamorphic rocks in central Newfoundland were exhumed and reburied under Tournaisian strata. New zircon fission‐track (ZFT) ages of metamorphic rocks below the Tournaisian unconformity yield post‐depositionally reset ages of 212–235 Ma indicating regional fluid‐absent reheating to at least ≥220°C. Post‐Tournaisian sedimentary thicknesses in surrounding basins show that burial alone cannot explain such temperatures, thus requiring that palaeo‐geothermal gradients increased to ≥30–40°C/km before final late Triassic accelerated cooling. We attribute these elevated palaeo‐geothermal gradients to localized thermal blanketing by insulating sediments overlying radiogenic high‐heat‐producing granitoids. Late Triassic rifting and magmatism before break up of Pangaea likely also contributed to elevated heat flow, as well as uplift, triggering late Triassic accelerated cooling and exhumation. Thermochronological ages of 240–200 Ma are seen throughout Atlantic Canada, and record rifting and basaltic magmatism on the conjugate margins of the Central Atlantic Ocean preceding the onset of oceanic spreading at ~190 Ma.  相似文献