Tests on low‐ductility RC frames under high‐ and low‐frequency excitations     

Ser‐Tong Quek  Chengmei Bian  Xilin Lu  Wensheng Lu  Haibei Xiong 《地震工程与结构动力学》2002,31(2):459-474

The response of low‐ductility reinforced concrete (RC) frames, designed typically for a non‐seismic region, subjected to two frequencies of base excitations is studied. Five half‐scaled, two‐bay, two‐storey, RC frames, each approximately 5 m wide by 3.3 m high, were subjected to both horizontal and/or vertical base excitations with a frequency of 40 Hz as well as a lower frequency of about 4 Hz (close to the fundamental frequency) using a shake table. The imposed acceleration amplitude ranged from 0.2 to 1.2g. The test results showed that the response characteristics of the structures differed under high‐ and low‐frequency excitations. The frames were able to sustain high‐frequency excitations without damage but were inadequate for low‐frequency excitations, even though the frames exhibited some ductility. Linear‐elastic time‐history analysis can predict reasonably well the structural response under high‐frequency excitations. As the frames were not designed for seismic loads, the reinforcement detailing may not have been adequate, based on the crack pattern observed. The effect of vertical excitation can cause significant additional forces in the columns and moment reversals in the beams. The ‘strong‐column, weak‐beam’ approach for lateral load RC frame design is supported by experimental observations. Copyright © 2001 John Wiley & Sons, Ltd.  相似文献   

Optimal design of passive energy dissipation systems based on H∞ and H2 performances     

J. N. Yang  S. Lin  J‐H. Kim  A. K. Agrawal 《地震工程与结构动力学》2002,31(4):921-936

Passive energy dissipation devices (EDDs), such as viscous dampers, viscoelastic dampers, etc., have been used to effectively reduce the dynamic response of civil infrastructures, such as buildings and bridges, subject to earthquakes and strong winds. The design of these passive energy dissipation devices (EDDs) involves the determination of the optimal locations and the corresponding capacities. In this paper, we present two optimal design methodologies for passive EDDs based on active control theories, including H_∞ and H₂ performances, respectively. The optimal design methodologies presented are capable of determining the optimal locations and the corresponding capacities of EDDs. Emphasis is placed on the application of linear matrix inequality (LMI) for the effective design of passive EDDs using the popular MATLAB toolboxes. One important advantage of the proposed approaches is that the computation of the structural response is not needed in the design process. The proposed optimal design methodologies have been applied to: (i) a 10‐storey building and a 24‐storey building both subject to earthquake excitations, and (ii) a 76‐storey wind‐excited benchmark building, to demonstrate the advantages of the proposed design methodologies over the conventional equal capacity design. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

Study on effects of damping in laminated rubber bearings on seismic responses for a ⅛ scale isolated test structure     

Bong Yoo  Yang‐Hann Kim 《地震工程与结构动力学》2002,31(10):1777-1792

The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

Analysis of Post-Failure Slope Movements within the Framework of Hazard and Risk Analysis     

Vaunat  Jean  Leroueil  Serge 《Natural Hazards》2002,26(1):81-107

The paper first recalls briefly a methodological framework to assess landslide hazard and risk analysis in terms of predisposition, triggering andrevealing factors. This framework, that reflects the mechanisms involved in the landslide, is based on the Geotechnical Characterisation of slope movements proposed by Vaunat et al. (1994) and Leroueil et al. (1996). The Geotechnical Characterisation can be schematized by a 3-D matrix having the following axes: types of movement; types ofmaterial; and the four stages of movement: pre-failure, failure, post-failure andreactivation. For each relevant element of this 3-D matrix, there is a characterisationsheet including: the controlling laws and parameters, the predisposition factors, thetriggering or aggravating factors, the revealing factors and the consequences of the movement. The paper focuses afterwards on the post-failure stage, which generallyis the most destructive, and on the mobility index. It is shown that this laterindex can be described as the product of sub-indices associated with failure, brittlenessof the material, ability of the soil to develop pore pressures, geometry of the moving soil mass and characteristics of the terrain. It is also shown how these aspectscan be incorporated into the Geotechnical characterisation of slope movements. This seems to provide a rational basis for examining slope movements at the post-failure stage and assessing associated risks.  相似文献   

An Early Cretaceous extinct spreading center in the northern Natal valley     

Anahita A. Tikku  Karen M. Marks  Louis C. Kovacs 《Tectonophysics》2002,347(1-3)

We have identified an extinct E–W spreading center in the northern Natal valley on the basis of magnetic anomalies which was active from chron M11 (133 Ma) to 125.3 Ma, just before chron M2 (124 Ma) in the Early Cretaceous. Seafloor spreading in the northern Natal valley accounts for approximately 170 km of north–south motion between the Mozambique Ridge and Africa. This extension resolves the predicted overlap of the continental (central and southern) Mozambique Ridge and Antarctica in the chron M2 to M11 reconstructions from Mesozoic finite rotation parameters for Africa and Antarctica. In addition, the magnetic data reveal that the Mozambique Ridge was an independent microplate from at least 133 to 125 Ma. The northern Natal valley extinct spreading center connects to the spreading center separating the Mozambique Basin and the Riiser-Larsen Sea to the east. It follows that the northern Mozambique Ridge was either formed after the emplacement of the surrounding oceanic crust or it is the product of a very robust spreading center. To the west the extinct spreading center connects to the spreading center separating the southern Natal valley and Georgia Basin via a transform fault. Prior to chron M11, there is still a problem with the overlap of Mozambique Ridge if it is assumed to be fixed with respect to either the African or Antarctic plates. Some of the overlap can be accounted for by Jurassic deformation of the Mozambique Ridge, Mozambique Basin, and Dronning Maud land. It appears though that the Mozambique Ridge was an independent microplate from the breakup of Gondwana, 160 Ma, until it became part of the African plate, 125 Ma.  相似文献   

Numerical Calculation of Equivalent Cell Permeability Tensors for General Quadrilateral Control Volumes     

Chuanping He  Michael G. Edwards  Louis J. Durlofsky 《Computational Geosciences》2002,6(1):29-47

A new method for upscaling fine scale permeability fields to general quadrilateral-shaped coarse cells is presented. The procedure, referred to as the conforming scale up method, applies a triangle-based finite element technique, capable of accurately resolving both the coarse cell geometry and the subgrid heterogeneity, to the solution of the local fine scale problem. An appropriate averaging of this solution provides the equivalent permeability tensor for the coarse scale quadrilateral cell. The general level of accuracy of the technique is demonstrated through application to a number of flow problems. The real strength of the conforming scale up method is demonstrated when the method is applied in conjunction with a flow-based gridding technique. In this case, the approach is shown to provide results that are significantly more accurate than those obtained using standard techniques.  相似文献   

Where the buffalo roam: Boundaries and the politics of scale in the yellowstone region     

Jean Lavigne 《GeoJournal》2002,58(4):285-292

For more than twenty years, the state of Montana has pursued a controversial policy of lethal control to manage winter migrations of bison from Yellowstone National Park. In the late 1990s, as the state and a number of federal agencies attempted to cooperatively outline a more palatable scenario for bison management, local environmental groups became active participants in the debate. This paper examines the strategies pursued by these organizations in the course of their attempt to construct a new, ecosystem-level territorial space and jurisdictional scale for bison, and places their struggle within the context of existing work in geography on the politics of scale. Ultimately, the failure of their efforts illustrates some of the important constraints faced by social groups that attempt to create new territorial regimes and new scales of resistance in the interstices of existing political structures.  相似文献   

Fitness-for-Purpose of Reference Material Reference Values in Relation to Traceability of Measurement, as Illustrated by USGS BCR-1, NIST SRM 610 and IAEA NBS28   总被引：1，自引：0，他引：1  

Jean S. Kane 《Geostandards and Geoanalytical Research》2002,26(1):7-29

As in all fields of sample analysis, reference materials play a large role in supporting measurements in the geosciences. While a rather large number of materials are in distribution (> 380), not all are equally effective or fit-for-purpose in supporting laboratory data quality and thereby assuring the desired comparability of measurements between laboratories. Equally important, reference values that are not fit-for-purpose cannot be used effectively to establish traceability links between laboratory measurements and national and international standards. The needed fitness-for-purpose is not achieved for reference values either when more than one reference value has been proposed and a consensus does not exist among users as to which should be used by all, or when reference value uncertainties are too large in comparison to those of routine laboratory measurements. The focus of this review will be, first to outline the current reality, and second to suggest ways in which certifications of RMs can be improved to provide reference values that are universally accepted and more fit-for-purpose in general laboratory use. The discussion will be illustrated largely by current uses of USGS BCR-1, NIST SRM 610 and IAEA NBS28, as these three materials are those for which the largest body of newly published data exists, according to recent bibliographies of the geoanalytical literature published annually in Geostandards Newsletter: The Journal of Geostandards and Geoanalysis.  相似文献   

Use of Chemotaxonomy To Study the Influence of Benzalkonium Chloride on Bacterial Populations in Biodegradation Testing     

Klaus Kümmerer  Ali Al‐Ahmad  Almut Henninger 《洁净——土壤、空气、水》2002,30(4):171-178

Contradictory results are reported for the behaviour of quaternary ammonium compounds (QACs) in sewage treatment plants (STPs). QACs may sorb onto activated sludge. Only little information is available with respect to effects of QACs against bacteria in STPs. Only 5 to 15 % of bacteria present in sewage sludge can be detected by means of culture dependent microbiological methods. The shift of the bacterial populations due to effects of test compounds have not been studied up to now with culture independent methods. The microbial populations shift was studied in situ using culture independent chemotaxonomy profiling ubiquinones and polyamines. Additionally, toxic effects of QACs against bacteria present in the test vessels of the Zahn‐Wellens test (OECD 302 B) were assessed with a toxicity control in the test. The ubiquinone profiles representing changes in Gram‐negative populations mainly showed that the activated sludge was affected only in test vessels containing benzalkonium chloride. According to chemotaxonomy Acinetobacter or/and some members of Pseudomonas spp. have been selected by benzalkonium chloride after some adaptation period (8 to 12 days).  相似文献   

Sediment yield and storage variations in the Négron River catchment (south western Parisian Basin,France) during the Holocene period     

Jean‐Jacques Macaire  Saïda Bellemlih  Christian Di‐Giovanni  Patrick De Luca  Lionel Visset  Jacques Bernard 《地球表面变化过程与地形》2002,27(9):991-1009

In the Négron River catchment area (162 km²), surface‐sediment stores are composed of periglacial calcareous ‘grèze’ (5 × 10⁶ t) and loess (21 × 10⁶ t), and Holocene alluvium (12·6 × 10⁶ t), peat (0·6 × 10⁶ t) and colluvium (18·5 × 10⁶ t). Seventy‐five per cent of the Holocene sediments is stored along the thalwegs. Present net sediment yield, calculated from solid discharge at the Négron outlet, is low (0·6 t km^?2 a^?1) due to the dominance of carbonate rocks in the catchment. Mean sediment yield during the Holocene period is 7·0 t km^?2 a^?1 from alluvium stores and 7·6 t km^?2 a^?1 from colluvium stores. Thus, the gross sediment yield during the Holocene period is about 18·7 t km^?2 a^?1 and the sediment delivery ratio 3 per cent. The yield considerably varies from one sub‐basin to another (3·9 to 24·5 t km^?2 a^?1) according to lithology: about 25 per cent and 50 per cent of initial stores of periglacial grèze and loess respectively were reworked during the Holocene period. Sediment yield has increased by a factor of 6 in the last 1000 years, due to the development of agriculture. The very high rate of sediment storage on the slope during that period (88 per cent of the yield) can be accounted for by the formation of cultivation steps (‘rideaux’). It is predicted that the current destruction of these steps will result in a sediment wave reaching the valley floors in the coming decades. Subboreal and Subatlantic sediments and pollen assemblages in the Taligny marsh, where one‐third of the alluvium is stored, show the predominant influence of human activity during these periods in the Négron catchment. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献