Trace elements contamination of agricultural soils affected by sulphide exploitation (Iberian Pyrite Belt,Sw Spain)   总被引：1，自引：0，他引：1  

María López  Isabel González  Antonio Romero 《Environmental Geology》2008,54(4):805-818

Agricultural soils of the Riotinto mining area (Iberian Pyrite Belt) have been studied to assess the degree of pollution by trace elements as a consequence of the extraction and treatment of sulphides. Fifteen soil samples were collected and analysed by ICP-OES and INAA for 51 elements. Chemical analyses showed an As–Cu–Pb–Zn association related with the mineralisation of the Iberian Pyrite Belt. Concentrations were 19–994 mg kg⁻¹ for As, 41–4,890 mg kg⁻¹ for Pb, 95–897 mg kg⁻¹ for Zn and of 27–1,160 mg kg⁻¹ for Cu. Most of the samples displayed concentrations of these elements higher than the 90th percentile of the corresponding geological dominium, which suggests an anthropogenic input besides the bedrock influence. Samples collected from sediments were more contaminated than leptosols because they were polluted by leachates or by mining spills coming from the waste rock piles. The weathering of the bedrock is responsible for high concentrations in Co, Cr and Ni, but an anthropogenic input, such as wind-blown dust, seems to be indicative of the high content of As, Cu, Pb and Zn in leptosols. The metal partitioning patterns show that most trace elements are associated with Fe amorphous oxy-hydroxides, or take part of the residual fraction. According to the results obtained, the following mobility sequence is proposed for major and minor elements: Mn, Pb, Cd, > Zn, Cu > Ni > As > Fe > Cr. The high mobility of Pb, Cu and Zn involve an environmental risk in this area, even in soils where the concentrations are not so high.  相似文献   

Seal integrity and feasibility of CO<Subscript>2</Subscript> sequestration in the Teapot Dome EOR pilot: geomechanical site characterization     

Laura Chiaramonte  Mark D. Zoback  Julio Friedmann  Vicki Stamp 《Environmental Geology》2008,54(8):1667-1675

This paper reports a preliminary investigation of CO₂ sequestration and seal integrity at Teapot Dome oil field, Wyoming, USA, with the objective of predicting the potential risk of CO₂ leakage along reservoir-bounding faults. CO₂ injection into reservoirs creates anomalously high pore pressure at the top of the reservoir that could potentially hydraulically fracture the caprock or trigger slip on reservoir-bounding faults. The Tensleep Formation, a Pennsylvanian age eolian sandstone is evaluated as the target horizon for a pilot CO₂ EOR-carbon storage experiment, in a three-way closure trap against a bounding fault, termed the S1 fault. A preliminary geomechanical model of the Tensleep Formation has been developed to evaluate the potential for CO₂ injection inducing slip on the S1 fault and thus threatening seal integrity. Uncertainties in the stress tensor and fault geometry have been incorporated into the analysis using Monte Carlo simulation. The authors find that even the most pessimistic risk scenario would require ∼10 MPa of excess pressure to cause the S1 fault to reactivate and provide a potential leakage pathway. This would correspond to a CO₂ column height of ∼1,500 m, whereas the structural closure of the Tensleep Formation in the pilot injection area does not exceed 100 m. It is therefore apparent that CO₂ injection is not likely to compromise the S1 fault stability. Better constraint of the least principal stress is needed to establish a more reliable estimate of the maximum reservoir pressure required to hydrofracture the caprock.  相似文献   

Environmental risk evaluation of the use of mine spoils and treated sewage sludge in the ecological restoration of limestone quarries     

M. M. Jordán  S. Pina  F. García-Orenes  M. B. Almendro-Candel  E. García-Sánchez 《Environmental Geology》2008,55(2):453-462

The ecologic restoration criteria in areas degraded from extraction activities require making use of their mine spoils. These materials do not meet fertility conditions to guarantee restoration success and therefore, need the incorporation of organic amendments to obtain efficient substratum. Reducing the deficiencies in the organic material and restoration material nutrients with the contribution of treated sewage sludge is proposed in this work. This experiment was based on a controlled study using columns. The work was conducted with two mine spoils, both very rich in calcium carbonate. The first mineral, of poor quality, came from the formation of aggregates of crushed limestone (Z). The other residual material examined originated in limestone extraction, formed by the levels of interspersed non-limestone materials and the remains of stripped soils (D). Two treatments were undertaken (30,000 and 90,000 kg/ha of sewage sludge), in addition to a control treatment. The water contribution was carried out with a device that simulated either short-duration rain or a flooding irrigation system in order to cover the surface and then percolate through the soil. The collection of leached water took place 24 h after the applications. Different parameters of the leached water were determined, including pH, electrical conductivity, nitrate anions, ammonium, phosphates, sulphates and chlorides. The values obtained for each irrigation application are discussed, and the nitrate values obtained were very elevated.  相似文献   

Experimental investigation of the effects of temperature and ionic strength on Mo isotope fractionation during adsorption to manganese oxides     

Laura E. Wasylenki  Bryan A. Rolfe  Thomas G. Spiro 《Geochimica et cosmochimica acta》2008,72(24):5997-6005

The Mo stable isotope system is being applied to study changes in ocean redox. Such applications implicitly assume that Mo isotope fractionation in aqueous systems is relatively insensitive to frequently changing environmental variables such as temperature (T) and ionic strength (I). A major driver of fractionation is the adsorption of Mo to Mn oxyhydroxide surfaces [Barling J. and Anbar A. D. (2004) Molybdenum isotope fractionation during adsorption by manganese oxides. Earth Planet. Sci. Lett.217(3-4), 315-329]. Here, we report the results of experiments that determine the extent to which Mo isotope fractionation during adsorption of Mo to the Mn oxyhydroxide mineral birnessite is sensitive to T and I. The results are compared to new predictions from quantum chemical computations. We measured fractionation from 1 to 50 °C at I = 0.1 m and found that Δ^97/95Mo_{dissolved-adsorbed} varies from 1.9‰ to 1.6‰ over this temperature range. Experiments were also performed at 25 °C in synthetic seawater (I = 0.7); fractionation at this condition was the same within analytical error as in low ionic strength experiments. These findings confirm that the Mo isotope fractionation during adsorption to Mn oxyhydroxides is relatively insensitive to variations and T and I over environmentally relevant ranges. To relate these findings to potential mechanisms of Mo isotope fractionation, we also report results for density functional theory computations of the fractionation between and various possible structures of molybdic acid as a function of temperature. Because no plausible species fractionates from with a magnitude matching the experiments, we are left with three possibilities to explain the fractionation: (1) solvation effects on the vibrational frequencies of aqueous species considered thus far are significant, such that our calculations in vacuo yield inaccurate fractionations; (2) a trace aqueous species not yet considered fractionates from and then adsorbs to birnessite; or (3) a surface complex not present in solution forms on birnessite in which Mo is not tetrahedrally coordinated. Our findings help validate assumptions underlying paleoceanographic applications of the Mo isotope system and also lead us closer to understanding the mechanism of isotope fractionation during adsorption of Mo to Mn oxyhydroxides.  相似文献   

Flood hazard delineation combining geomorphological and hydrological methods: an example in the Northern Iberian Peninsula   总被引：2，自引：1，他引：1  

J. Lastra  E. Fernández  A. Díez-Herrero  J. Marquínez 《Natural Hazards》2008,45(2):277-293

Flood mapping requires the combination and integration of geomorphological and hydrological-hydraulic methods; however, despite this, there is very little scientific literature that compares and validates both methods. Two types of analysis are addressed in the present article. On the one hand, maps of flood plains have been elaborated using geomorphological evidence and historical flood data in the mountainous area of northwestern Spain, covering an area of more then 232 km² of floodplains. On the other hand, a hydrometeorological model has been developed (Clark semidistributed unit hydrograph) in the Sarria River basin (155 km², NW Spain). This basin is not gauged, hence the model was subjected to a goodness-of-fit test of its parameter (curve number) by means of Monte Carlo simulation. The peak flows obtained by means of the hydrological model were used for hydraulic modeling (one-phase, one-dimensional and steady flow) in a 4 km² urban stretch of the river bed. The delineation of surface areas affected by floods since 1918, as well as those analyzed subsequent to the geomorphological study, reveals a high degree of reliability in the delineation of the flooded areas with frequent recurrence intervals (<50 years). If we compare these flooded surface areas with the estimate obtained by the hydrological-hydraulic method we can see that the latter method overestimates the extent of the surface water by 144% for very frequent recurrence intervals (>10 years) and underestimates it as the recurrence interval increases, by up to 80% less floodplain for exceptional events (>500 years). Finally, a management map is put forth combining the most reliable results available by integrating both methods. Originally presented at the Sixth International Conference on Geomorphology.  相似文献   

Deep-seated gravitational slope deformations and their influence on consequent mass movements (case studies from the highest part of the Czech Carpathians)   总被引：3，自引：0，他引：3  

Jan Hradecký  Tomáš Pánek 《Natural Hazards》2008,45(2):235-253

Gravitational spreading of mountain ridges displays primary disequilibrium of flysch mountain areas of the Czech Carpathians. The progression of various types of mass movements is a product of long-term ridge disintegration and is predisposed by the geological structure of the area and the upper Tertiary-Quaternary morphogenesis of the mountain area. Deep-seated slope deformations are spatially interconnected by the occurrence of some other types of slope deformations (e.g. debris flows, debris slides, slumps, rock avalanches, etc.), which pose a considerable risk for the existence of human society. An important causative factor in these dynamically developing hazardous processes is, among other factors, the way in which land has been used in the last three centuries. Therefore, the occurrence of various types of slope deformations is studied in terms of their relation to deep-seated gravitational deformations and in terms of other limiting factors (structural geological, morphological and climatic factors, manmade impacts, etc.). The paper presents several case studies of slope deformations (Velká Čantoryje Mt, Lysá hora Mt, Ropice Mt and Smrk Mt) in the area of the Outer Carpathians within the territory of the Czech Republic and also adverts to some consequences in terms of the socioeconomic structure of the landscape.  相似文献   

Impact of lightning on organic matter-rich soils: influence of soil grain size and organic matter content on underground fires     

Vittorio Zanon  Fátima Viveiros  Catarina Silva  Ana Rita Hipólito  Teresa Ferreira 《Natural Hazards》2008,45(1):19-31

A detailed study was carried out on a piece of land that had been struck by lightning during the violent rainstorm that raged over the Island of S?o Miguel (Azores Archipelago) in late October 2006. Temperature and gas measurements (CO₂, CO, H₂S and CH₄) were performed in four study trenches, dug in an area of ∼3 m², where an underground fire had been initiated by the impact with a lightning stroke, followed by the emission of a column of gases and smoke. The soil under study was originally a well-pedogenized about 80 cm thick bed, made of volcanic clayey to silty tephra fallouts and contained 5.5–9.7% of organic matter. The underground fire was monitored for one week and revealed a peak release of 404 ppm CO and 3.4% CO₂ originating from a horizon located about 45 cm under the soil surface. Measurements of temperature, performed one week after the impact, indicated a maximum value of 326°C inside the soil, while 516.5°C were measured on the surface of a lava block interred about 20 cm under the surface. Subsequently, a stratigraphic and sedimentologic study proved the role of the grain-size of the soil and of the organic matter content of the different horizons of the impact area, in determining the ratio between anoxic/oxidised combustion conditions and in the progress of the process itself. It was also noticed that combustion was not total all over in the soil bed and that the process had slightly migrated toward SW during the observation period. The combustion process went on for about ten days, in spite of several other violent rainstorms, until it was artificially extinguished through the excavations made to obtain study trenches. This particular circumstance evidenced the potential natural hazard represented by this kind of atmospheric event, especially in a land where the volcanic nature of the soil may easily mislead inexperienced observers and, consequently, delay proper action.  相似文献   

Methodology of hydrogeological characterization of deep carbonate aquifers as potential reservoirs of groundwater. Case of study: the Jurassic aquifer of <Emphasis Type="Italic">El Maestrazgo</Emphasis> (Castellón,Spain)     

M. Mejías  J. Garcia-Orellana  J. L. Plata  M. Marina  E. Garcia-Solsona  B. Ballesteros  P. Masqué  J. López  C. Fernández-Arrojo 《Environmental Geology》2008,54(3):521-536

A methodology for the characterization of deep carbonate aquifers has been developed and applied to El Maestrazgo Jurassic aquifer in Castellón, Spain. Characterization of these aquifer formations, located at more than 300 m deep, consisted of a previous phase of compilation, analysis and synthesis of the existing information about the area, followed by a coordinated combination of different speciality studies: geology, stratigraphy, structural analysis, hydrogeology, hydrochemistry, geophysics and remote sensing. Geological studies included geological mapping, definition of stratigraphical units and facies and structural analysis. The aim of the hydrogeology study was to define aquifer formations, recharge area, aquifer points inventory and groundwater flow directions for the establishment of piezometric and water quality observation nets. Special techniques were applied, like thermal infrared aerial images and the evaluation of submarine groundwater discharge by means of natural radium isotopes. Hydrochemical techniques, including majority elements characterization and stable isotopes (¹⁸O, ²H and ³H) determination, allowed classifying hydrochemical facies and establishing a renewal pattern for water within the system. Geophysics was useful in determining the aquifer geometry, the features of the basement and the petrophysical characteristics of the geological formations. Preliminary results show an important tectonic complexity and the possibilities for groundwater uses in the area of study.  相似文献   

European Seismological Commission Sub-Commission for the Carpathian and Balkan regions     

Alois Zátopek 《Studia Geophysica et Geodaetica》1969,13(1):100-103

  相似文献   

On the basic principles of geophysical radioactive measurements     

P. Márton  L. Stegena 《Pure and Applied Geophysics》1962,53(1):55-64

Summary The process of radon diffusion in space and time through rocks is treated in detail from the point of view of radiometric prospecting for oil. Taking into account the depth and diffusivity conditions encountered in nature it is stated that vertical radon diffusion reaching from the oil deposits up to the surface cannot be expected. Time intervals as required for setting in of a stationary concentration state and decay conditions of the radon lead to the conclusion that the penetration of emanometric measurements seldom exceeds the depth of 5–10 m.  相似文献