Significant intrusion of geothermal water into fresh groundwater takes place in the Puebla Valley aquifer system, Mexico. The decline in the potentiometric surface due to the overexploitation of the groundwater induces this intrusion. This hydrological system comprises three aquifers located in Plio-Quaternary volcanic sediments and Mesozoic calcareous rocks. The hydraulic balance of the aquifer shows that the annual output exceeds the natural inputs by 12 million m3. Between 1973 and 2002, a drop in the potentiometric surface, with an 80 m cone of depression, was identified in a 5-km-wide area located southwest of the city of Puebla. Chemical analyses performed on water samples since 1990 have shown an increase in total dissolved solids (TDS) of more than 500 mg/L, coinciding with the region showing a cone of depression in the potentiometric surface. A three-dimensional flow and transport model, based on the hydrogeological and geophysical studies, was computed by using the MODFLOW and MT3D software. This model reproduces the evolution of the aquifer system during the last 30 years and predicts for 2010 an additional drawdown in the potentiometric surface of 15 m, and an increase in the geothermal water intrusion. 相似文献
Summary ?Retrievals of atmospheric aerosol optical thickness are highly dependent on the choice of the class describing the aerosol
properties leading to significant errors while using classes available in the literature. High spectral resolution measurements
from GOME (Global Ozone Monitoring Experiment) between the ultraviolet and the near infrared can be used for an accurate characterization
of the aerosol optical properties. The radiometer MVIRI (METEOSAT Visible and Infrared Imager) on board the geostationary
satellite METEOSAT, while being equipped only with broadband VIS channel, ensures an adequate half-hourly monitoring of the
atmospheric conditions over a large portion of the Earth. The present algorithm is based on a combination of data from both
sensors for the retrieval of the aerosol optical thickness at the reference wavelength of 0.55 μm (AOT). A case of a desert
dust outbreak from the African continent over the Atlantic Ocean is examined. AOT values obtained using a priori fixed classes
taken from the literature are compared with those retrieved with this algorithm using the GOME-derived classes. Systematic
differences of the order of a few tenths on average are found which remain significant also after considering the measurement
errors. This represents a novelty introduced by the synergetic use of both sensors.
Received March 13, 2002 相似文献
The determination of FeO of geologic materials by modern instrumental methods (such as atomic absorption spectroscopy (AAS), inductively coupled plasma atomic emission spectroscopy (ICP-AES), X-ray fluorescence (XRF), etc.) cannot distinguish between different oxidation states of elements. In many cases, the oxidation state of Fe has to be known in order to perform several chemical calculations (norms, etc.) and discuss the reactions that occur during weathering, hydrothermal alteration and other processes. A modified Wilson method is proposed, giving reproducible results in a much shorter time than the classical method. Back-titration with potassium dichromate and an Fe(II) and ammonia sulphate solution is used, after dissolution of the sample powder in a heated HF/H3PO4 mixture and an ammonium vanadate solution. This modified method, tested with several international reference materials, gives reliable results, equivalent to the ones cited in the literature for the reference materials. 相似文献
We propose a model for the generation of average MORBs based on phase relations in the CaO-MgO-Al2O3-SiO2-CO2 system at pressures from 3 to 7 GPa and in the CaO-MgO-Al2O3-SiO2-Na2O-FeO (CMASNF) system at pressures from ∼0.9 to 1.5 GPa. The MELT seismic tomography (Forsyth et al., 2000) across the East Pacific Rise shows the largest amount of melt centered at ∼30-km depth and lesser amounts at greater depths. An average mantle adiabat with a model-system potential temperature (Tp) of 1310°C is used that is consistent with this result. In the mantle, additional minor components would lower solidus temperatures ∼50°C, which would lower Tp of the adiabat for average MORBs to ∼1260°C. The model involves generation of carbonatitic melts and melts that are transitional between carbonatite and kimberlite at very small melt fractions (<0.2%) in the low-velocity zone at pressures of ∼2.6 to 7 GPa in the CMAS-CO2 system, roughly the pressure range of the PREM low-velocity zone. These small-volume, low-viscosity melts are mixed with much larger volumes of basaltic melt generated at the plagioclase-spinel lherzolite transition in the pressure range of ∼0.9 to 1.5 GPa.In this model, solidus phase relations in the pressure range of the plagioclase-spinel lherzolite transition strongly, but not totally, control the major-element characteristics of MORBs. Although the plagioclase-spinel lherzolite transition suppresses isentropic decompression melting in the CMAS system, this effect does not occur in the topologically different and petrologically more realistic CMASNF system. On the basis of the absence of plagioclase from most abyssal peridotites, which are the presumed residues of MORB generation, we calculate melt productivity during polybaric fractional melting in the plagioclase-spinel lherzolite transition interval at exhaustion of plagioclase in the residue. In the CMASN system, these calculations indicate that the total melt productivity is ∼24%, which is adequate to produce the oceanic crust. The residual mineral proportions from this calculation closely match those of average abyssal peridotites.Melts generated in the plagioclase-spinel lherzolite transition are compositionally distinct from all MORB glasses, but do not have a significant fractional crystallization trend controlled by olivine alone. They reach the composition field of erupted MORBs mainly by crystallization of both plagioclase and olivine, with initial crystallization of either one of these phases rapidly joined by the other. This is consistent with phenocryst assemblages and experimental studies of the most primitive MORBs, which do not show an olivine-controlled fractionation trend. The model is most robust for the eastern Pacific, where an adiabat with a Tp of ∼1260°C is supported by the MELT seismic data and where the global inverse correlation of (FeO)8 with (Na2O)8 is weak. Average MORBs worldwide also are well modeled. A heterogeneous mantle consisting of peridotite of varying degrees of major-element depletion combined with phase-equilibrium controls in the plagioclase-spinel lherzolite transition interval would produce the form of the global correlations at a constant Tp, which suggests a modest range of Tp along ridges. Phase-composition data for the CMASNF system are presently not adequate for quantitative calculation of (FeO)8-(Na2O)8-(CaO/Al2O3)8 systematics in terms of this model. The near absence of basalts in the central portion of the Gakkel Ridge suggests a lower bound for Tp along ridges of ∼1240°C, a potential temperature just low enough to miss the solidus for basalt production at ∼0.9 GPa. An upper bound for Tp is poorly constrained, but the complete absence of picritic glasses in Iceland and the global ridge system suggests an upper bound of ∼1400°C. In contrast to some previous models for MORB generation that emphasize large potential temperature variations in a relatively homogeneous peridotitic mantle, our model emphasizes modest potential temperature variations in a peridotitic mantle that shows varying degrees of heterogeneity. Calculations indicate that melt productivity changes from 0 to 24% for a change in Tp from 1240 to 1260°C, effectively producing a rapid increase to full crustal thickness or decrease to none as ridges appear and disappear. 相似文献
This paper presents results recently obtained for generating site-specific ground motions needed for design of critical facilities. The general approach followed in developing these ground motions using either deterministic or probabilistic criteria is specification of motions for rock outcrop or very firm soil conditions followed by adjustments for site-specific conditions. Central issues in this process include development of appropriate attenuation relations and their uncertainties, differences in expected motions between Western and Eastern North America, and incorporation of site-specific adjustments that maintain the same hazard level as the control motions, while incorporating uncertainties in local dynamic material properties. For tectonically active regions, such as the Western United States (WUS), sufficient strong motion data exist to constrain empirical attenuation relations for M up to about 7 and for distances greater than about 10–15 km. Motions for larger magnitudes and closer distances are largely driven by extrapolations of empirical relations and uncertainties need to be substantially increased for these cases.
For the Eastern United States (CEUS), due to the paucity of strong motion data for cratonic regions worldwide, estimation of strong ground motions for engineering design is based entirely on calibrated models. The models are usually calibrated and validated in the WUS where sufficient strong motion data are available and then recalibrated for applications to the CEUS. Recalibration generally entails revising parameters based on available CEUS ground motion data as well as indirect inferences through intensity observations. Known differences in model parameters such as crustal structure between WUS and CEUS are generally accommodated as well. These procedures are examined and discussed. 相似文献
The deepest part (29.5 m) of Elk Lake, ClearwaterCounty, northwestern Minnesota, contains a complete Holocene section that iscontinuously varved. The varve components are predominantly autochthonous(CaCO3, organic matter, biogenic silica, and several iron andmanganese minerals), but the varves do contain a minor detrital-clastic(aluminosilicate) component that is predominantly wind-borne (eolian) andprovides an important record of atmospheric conditions. Singular spectrumanalysis (SSA) and wavelet analysis of varve thickness recognized significantperiodicities in the multicentennial and multidecadal bands that varied inpower (i.e., variable significance) and position (i.e., variable period) withinthe periodic bands. Persistent periodicities of about 10, 22, 40, and 90 years,and, in particular, multicentennial periodicities in varve thickness and otherproxy variables are similar to those in spectra of radiocarbon production, aproxy for past solar activity. This suggests that there may be a solar control,perhaps through geomagnetic effects on atmospheric circulation. Multicentennialand multidecadal periodicities also occur in wavelet spectra of relativegray-scale density. However, gray-scale density does not appear to correlatewith any of the measured proxy variables, and at this point we do not know whatcontrolled gray scale. 相似文献
Freshwater and marine ecosystems are exposed to various multi-component mixtures of pollutants. Nevertheless, most ecotoxicological research and chemicals regulation focus on hazard and exposure assessment of individual substances only, the problem of chemical mixtures in the environment is ignored to a large extent. In contrast, the assessment of combination effects has a long tradition in pharmacology, where mixtures of chemicals are specifically designed to develop new products, e.g. human and veterinary drugs or agricultural and non-agricultural pesticides. In this area, two concepts are frequently used and are thought to describe fundamental relationships between single substance and mixture effects: Independent Action (Response Addition) and Concentration Addition. The question, to what extent these concepts may also be applied in an ecotoxicological and regulatory context may be considered a research topic of major importance, as the concepts would allow to make use of already existing single substance toxicity data for the predictive assessment of mixture toxicities. Two critical knowledge gaps are identified: (a) There is a lack of environmental realism, as a huge part of our current knowledge about the applicability of the concepts is restricted to artificial situations with respect to mixture composition or biological effect assessment. (b) The knowledge on what exactly is needed for using the concepts as tools for the predictive mixture toxicity assessment is insufficient. Both gaps seriously hamper the necessary, scientifically sound consideration of mixture toxicities in a regulatory context.In this paper, the two concepts will be briefly introduced, the necessity of considering the toxicities of chemical mixtures in the environment will be demonstrated and the applicability of Independent Action and Concentration Addition as tools for the prediction and assessment of mixture toxicities will be discussed. An overview of the specific aims and approaches of the BEAM project to fill in the identified knowledge gaps is given and first results are outlined. 相似文献
High spatial resolution U–Pb dates of zircons from two consanguineous ignimbrites of contrasting composition, the high-silica rhyolitic Toconao and the overlying dacitic Atana ignimbrites, erupted from La Pacana caldera, north Chile, are presented in this study. Zircons from Atana and Toconao pumice clasts yield apparent 238U/206Pb ages of 4.11±0.20 Ma and 4.65±0.13 Ma (2σ), respectively. These data combined with previously published geochemical and stratigraphic data, reveal that the two ignimbrites were erupted from a stratified magma chamber. The Atana zircon U–Pb ages closely agree with the eruption age of Atana previously determined by K–Ar dating (4.0±0.1 Ma) and do not support long (>1 Ma) residence times. Xenocrystic zircons were found only in the Toconao bulk ignimbrite, which were probably entrained during eruption and transport. Apparent 238U/206Pb zircon ages of 13 Ma in these xenocrysts provide the first evidence that the onset of felsic magmatism within the Altiplano–Puna ignimbrite province occurred approximately 3 Myr earlier than previously documented. 相似文献
This paper deals with the taxonomic revision of the Early Cretaceous large, many-chambered planispiral planktonic foraminifera, historically assigned to the genus Globigerinelloides or alternatively assigned in the 1990s to the genera Globigerinelloides Cushman and ten Dam, Biglobigerinella Lalicker, Blowiella Krechmar and Gorbachik and Alanlordella BouDagher-Fadel. In a previous paper we demonstrated that the morphological and microstructural features used in the literature for distinguishing Blowiella from Globigerinelloides have value only at species level, and the former genus was thus invalidated (being the junior synonym). Moreover, the Late Aptian specimens assigned to Biglobigerinella by some authors, based on the presence of twin last chamber(s), are also included in Globigerinelloides because individuals sharing the same features (number of chambers, growth rate, size of umbilicus, and a finely perforate wall) may or may not possess twin last chamber(s). Meanwhile, Moullade et al. questioned the taxonomic value of Alanlordella, erected by BouDagher-Fadel to accommodate planispiral taxa possessing a macroperforate wall. All the species analysed here possess a finely perforate wall and consequently cannot be assigned to this taxon.The large species of Globigerinelloides retained here, with six or more chambers in the outer whorl, are G. algerianus Cushman and ten Dam, G. aptiensis Longoria, G. barri (Bolli, Loeblich and Tappan) and G. ferreolensis (Moullade).In the sections studied, Globigerinelloides aptiensis was first found close to the Barremian/Aptian boundary, even though this species was recorded in Spain (Rio Argos) in the mid Upper Barremian; very rare, small, seven-chambered individuals here assigned to Globigerinelloides ferreolensis are recorded in the Lower Aptian (just below and within the Selli Level, OAE1a), while a few specimens belonging to Globigerinelloides barri occur in the Globigerinelloides ferreolensis Zone (Upper Aptian). Globigerinelloides aptiensis and G. ferreolensis range up to the Ticinella bejaouaensis Zone while Globigerinelloides barri disappears at the top of the Globigerinelloides algerianus Zone; finally, Globigerinelloides algerianus obviously spans the eponymous total range zone.From an evolutionary point of view, two lineages within the many-chambered Globigerinelloides have been recognized. In the first, already known in the literature, Globigerinelloides aptiensis gave rise to G. ferreolensis, which evolved into G. algerianus; the latter in turn gave rise to Pseudoplanomalina cheniourensis as the final evolutionary member. In the second lineage Globigerinelloides barri originated from G. blowi. 相似文献