Optimal design of superelastic‐friction base isolators for seismic protection of highway bridges against near‐field earthquakes     

Osman E. Ozbulut  Stefan Hurlebaus 《地震工程与结构动力学》2011,40(3):273-291

The seismic response of a multi‐span continuous bridge isolated with novel superelastic‐friction base isolator (S‐FBI) is investigated under near‐field earthquakes. The isolation system consists of a flat steel‐Teflon sliding bearing and a superelastic NiTi shape memory alloy (SMA) device. The key design parameters of an S‐FBI system are the natural period of the isolated bridge, the yielding displacement of the SMA device, and the friction coefficient of the sliding bearings. The goal of this study is to obtain optimal values for each design parameter by performing sensitivity analysis of a bridge isolated by an S‐FBI system. First, a three‐span continuous bridge is modeled as two‐degrees‐of‐freedom with the S‐FBI system. A neuro‐fuzzy model is used to capture rate‐ and temperature‐dependent nonlinear behavior of the SMA device. Then, a set of nonlinear time history analyses of the isolated bridge is performed. The variation of the peak response quantities of interest is shown as a function of design parameters of the S‐FBI system and the optimal values for each parameter are evaluated. Next, in order to assess the effectiveness of the S‐FBI system, the response of the bridge isolated by the S‐FBI system is compared with the response of the non‐isolated bridge and the same bridge isolated by pure‐friction (P‐F) sliding isolation system. Finally, the influence of temperature variations on the performance of the S‐FBI system is evaluated. The results show that the optimum design of a bridge with the S‐FBI system can be achieved by a judicious specification of design parameters. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

Groundwater recharge in arid areas induced by tropical cyclones: lessons learned from Gonu 2007 in Sultanate of Oman   总被引：4，自引：1，他引：3  

Osman Abdalla  Rashid bin Yahya Al-Abri 《Environmental Earth Sciences》2011,63(2):229-239

Younger groundwater found in some Omani aquifers is a result of recent recharge from cyclonic and storm events [Weyhenmeyer et al. (Science 287:842–845, 2000); Young et al. (J Appl Geophys 57:43–61, 2004)]. The analysis of the meteorological data in Oman indicates an anomalous rainfall on a decadal interval whereas cyclones frequency is expected to increase due to global climatic changes. The cyclone Gonu has severely struck the eastern Omani coasts in 2007 resulting in devastating floods. Huge volume of water (3,672 mm³) spread over the coastal plain calling for an assessment of potential groundwater recharge subsequent to this event. The present study evaluates groundwater recharge with respect to Gonu 2007 to assess the potential of recharge induced by such cyclones in the arid zones. The hydrographs of several piezometers sited along the coastal plain in Muscat Province have been studied and variation in water table rise has been analyzed. Significant water table rise is indicated for areas with geological and structural settings favoring rapid infiltration of water yielding considerable groundwater mound, whereas piezometers located in less favorable zones show minimum rise of water table. However, soon after the floods the aquifer hydrodynamics has readjusted to attain equilibrium and the groundwater mound dissipated. The cumulative rise of the water table on an areal extent does not exceed a few centimeters indicating lesser volume of recharge. Comparatively, recharge from frequent precipitation along favorable zones produces more significant recharge compared with cyclonic events where surface water residence time is shorter to allow for efficient infiltration.  相似文献   

Lithologic and diagenetic attributes of the Sharwayn (Maastrichtian) and Umm Er Radhuma (late Paleocene–Eocene) formations and their significance to the K-T unconformity, Jabal Samhan area, Dhofar, Sultanate of Oman     

Osman Salad Hersi 《Arabian Journal of Geosciences》2011,4(1-2):147-160

The boundary separating Maastrichtian Sharwayn Formation from late Paleocene Eocene Umm Er Radhuma (UER) Formation in Dhofar, southern Oman, is characterized by a regionally extensive unconformity. The Jabal Samhan escarpment, north of Marbat-Sadh transect, preserves this unconformable boundary. This paper addresses the lithologic and diagenetic differences of the strata across the boundary and discusses their significance and link to the development of the upper Maastrichtian to lower Paleocene unconformity. The upper part of the Sharwayn Formation is characterized by lower thickly bedded, bioclastic, and peloidal mudstone to wackestone lithofacies overlain by a thick ledge (~5.5 m) of medium to coarse crystalline, (sucrosic) dolostone. Poorly preserved outlines of the framework grains suggest an original peloidal and bioclastic grainstone texture for the dolostone unit. The contact with the overlying UER Formation is sharp. The UER Formation is characterized by thickly bedded, bioclastic mudstone to wackestone overlain by coarse-grained, foraminiferal grainstone. The dolomitization process of the dolomite unit at the top of the Sharwayn Formation is envisaged to a shallow subsurface mixed meteoric and sea water diagenetic realm. This interpretation is supported by an inferred timing of dolomitization of latest Maastrichtian (post-Sharwayn Formation) to early Paleocene (pre-EUR Formation), preservation (although poorly recognizable) of the original depositional texture and diagenetic features that postdate the sucrosic dolomite. Pervasive dolomitization of the dolomite unit was controlled by its original grainstone texture, which permitted efficient percolation of the dolomitizing fluids. Correlation between the reference section of the formation and the section studied in this work raises the thickness of the formation to 28.5 m (relative to a thickness of 22 m at the reference section). Analysis of the new composite section suggests that deposition of the formation took place in a shallowing-upward setting where low-energy subtidal sediments (the lower limestone unit) were succeeded by a high energy sand shoal (upper dolomitized unit).This shallowing-upward succession is attributed to a third-order sea-level drop. The later is also recognized in many parts of the Arabian Peninsula, as well as globally, and interpreted as eustatic sea-level fluctuation.  相似文献   

Simple and multiple regression models for relationship between electrical resistivity and various soil properties for soil characterization     

Fahad Irfan Siddiqui  Syed Baharom Azahar Bin Syed Osman 《Environmental Earth Sciences》2013,70(1):259-267

Precise determination of engineering properties of soil is essential for proper design and successful construction of any structure. The conventional methods for determination of engineering properties are invasive, costly and time-consuming. Electrical resistivity survey is an attractive tool for delineate subsurface properties without soil disturbance. Reliable correlations between electrical resistivity and other soil properties will enable us to characterize the subsurface soil without borehole sampling. This paper presents the correlations of electrical resistivity with various properties of soil. Soil investigations, field electrical resistivity survey and laboratory electrical resistivity measurements were conducted. The results from electrical resistivity tests (field and laboratory) and laboratory tests were analyzed together to understand the interrelation between electrical resistivity and various soil properties. The test results were evaluated using simple and multiple regression analysis. From the data analysis, significant quantitative and qualitative correlations have been obtained between resistivity and moisture content, friction angle and plasticity index. Weaker correlations have been observed for cohesion, unit weight of soil and effective size (D ₁₀).  相似文献   

High-resolution facies and porosity models of the upper Jurassic Arab-D carbonate reservoir using an outcrop analogue, central Saudi Arabia     

Hassan Eltom  Mohammed Makkawi  Osman Abdullatif  Khalid Alramadan 《Arabian Journal of Geosciences》2013,6(11):4323-4335

Subsurface models of hydrocarbon reservoirs are coarse and of low resolution when compared with the actual geologic characteristics. Therefore, the understanding of the three-dimensional architecture of reservoir units is often incomplete. Outcrop analogues are commonly used to understand the spatial continuity of reservoir units. In this study, a Late Jurassic outcrop analogue for the Arab-D reservoir of central Saudi Arabia was used to build a high-resolution model that captures fine geologic details. Subsurface reservoir lithofacies were matched with those from the studied outcrop, and porosity values derived from published core and well log data from the Ain Dar, Uthmanyah, and Shudgum areas of the Ghawar Field, eastern Saudi Arabia, were then applied to the equivalent lithofacies in the outcrop. Maximum, minimum, and average subsurface porosity for each lithofacies were distributed in the facies model using a geostatistical algorithm to produce nine porosity models for the field data. Several realisations were run to visualise the variability in each model and to quantitatively measure the uncertainty associated with the models. The results indicated that potential reservoir zones were associated with grainstone, packstone, and some wackestone layers. Semivariogram analysis of the lithofacies showed good continuity in the N-S direction and less continuity in the E-W direction. The high-resolution lithofacies models detected permeability barriers and isolated low porosity bodies within the potential reservoir zones. This model revealed the porosity distribution in areas smaller than one cell in the subsurface model and highlighted the uncertainty associated with several aspects of the model.  相似文献   

Geochemistry of Pliocene/Pleistocene basalts along the Central Anatolian Fault Zone (CAFZ), Turkey     

Osman Parlak  Michel Delaloye  Cavit Demirkol  Ulvi Can Ünlügenç 《Geodinamica Acta》2013,26(1-3):159-167

Abstract

Pliocene-Pleistocene volcanism accompanied strike-slip-related transtensional deformation along the K?z?l?rmak fault segment of the Central Anatolian fault zone (CAFZ) in the west of ?ark??la (Sivas-central Turkey). These volcanic rocks are represented by alkali olivine basalts. They can be divided into four different sub-groups on the basis of their Zr, Nb, TiO₂ contents. A primitive mantle-normalized incompatible trace element diagram for four subgroups shows close similarity to typical OIB pattern. Some of the incompatible trace element ratios (Ce/Y, Zr/Nb, La/Ba, La/Nb) are also akin to OIB values. Highly fractionated REE patterns (La/Yb_N=24.7–9.2) with no Eu anomaly are the main features of the alkali basalts and are comparable to alkaline volcanism in continental rift zones. On the basis of Al₂O₃/TiO₂, Nb/Y, Zr/Y Zr/Nb ratios, the geochemical differences among four sub-groups can be explained by variable degrees of partial melting of compositionally similar mantle source. Th/Nb, Th/Y, Nb/Y ratios and the primitive mantle-normalized trace element diagram suggests significant amount of crustal involvement for most of the alkali olivine basalts erupted along the CAFZ. Rupture of the continental lithosphere by strike-slip-related transtensional deformation might have caused decompressional partial melting of the asthenospheric mantle and generating alkali olivine basalts in this region. © 2001 Éditions scientifiques et médicales Elsevier SAS.  相似文献   

Subduction,ophiolite genesis and collision history of Tethys adjacent to the Eurasian continental margin: new evidence from the Eastern Pontides,Turkey     

Alastair Robertson  Osman Parlak  Timur Ustaömer  Kemal Taslı  Nurdan İnan  Paulian Dumitrica 《Geodinamica Acta》2013,26(3-4):230-293

This paper presents several types of new information including U–Pb radiometric dating of ophiolitic rocks and an intrusive granite, micropalaeontological dating of siliceous and calcareous sedimentary rocks, together with sedimentological, petrographic and structural data. The new information is synthesised with existing results from the study area and adjacent regions (Central Pontides and Lesser Caucasus) to produce a new tectonic model for the Mesozoic–Cenozoic tectonic development of this key Tethyan suture zone.

The Tethyan suture zone in NE Turkey (Ankara–Erzincan–Kars suture zone) exemplifies stages in the subduction, suturing and post-collisional deformation of a Mesozoic ocean basin that existed between the Eurasian (Pontide) and Gondwanan (Tauride) continents. Ophiolitic rocks, both as intact and as dismembered sequences, together with an intrusive granite (tonalite), formed during the Early Jurassic in a supra-subduction zone (SSZ) setting within the ?zmir–Ankara–Erzincan ocean. Basalts also occur as blocks and dismembered thrust sheets within Cretaceous accretionary melange. During the Early Jurassic, these basalts erupted in both a SSZ-type setting and in an intra-plate (seamount-type) setting. The volcanic-sedimentary melange accreted in an open-ocean setting in response to Cretaceous northward subduction beneath a backstop made up of Early Jurassic forearc ophiolitic crust. The Early Jurassic SSZ basalts in the melange were later detached from the overriding Early Jurassic ophiolitic crust.

Sedimentary melange (debris-flow deposits) locally includes ophiolitic extrusive rocks of boninitic composition that were metamorphosed under high-pressure low-temperature conditions. Slices of mainly Cretaceous clastic sedimentary rocks within the suture zone are interpreted as a deformed forearc basin that bordered the Eurasian active margin. The basin received a copious supply of sediments derived from Late Cretaceous arc volcanism together with input of ophiolitic detritus from accreted oceanic crust.

Accretionary melange was emplaced southwards onto the leading edge of the Tauride continent (Munzur Massif) during latest Cretaceous time. Accretionary melange was also emplaced northwards over the collapsed southern edge of the Eurasian continental margin (continental backstop) during the latest Cretaceous. Sedimentation persisted into the Early Eocene in more northerly areas of the Eurasian margin.

Collision of the Tauride and Eurasian continents took place progressively during latest Late Palaeocene–Early Eocene. The Jurassic SSZ ophiolites and the Cretaceous accretionary melange finally docked with the Eurasian margin. Coarse clastic sediments were shed from the uplifted Eurasian margin and infilled a narrow peripheral basin. Gravity flows accumulated in thrust-top piggyback basins above accretionary melange and dismembered ophiolites and also in a post-collisional peripheral basin above Eurasian crust. Thickening of the accretionary wedge triggered large-scale out-of-sequence thrusting and re-thrusting of continental margin and ophiolitic units. Collision culminated in detachment and northward thrusting on a regional scale.

Collisional deformation of the suture zone ended prior to the Mid-Eocene (~45?Ma) when the Eurasian margin was transgressed by non-marine and/or shallow-marine sediments. The foreland became volcanically active and subsided strongly during Mid-Eocene, possibly related to post-collisional slab rollback and/or delamination. The present structure and morphology of the suture zone was strongly influenced by several phases of mostly S-directed suture zone tightening (Late Eocene; pre-Pliocene), possible slab break-off and right-lateral strike-slip along the North Anatolian Transform Fault.

In the wider regional context, a double subduction zone model is preferred, in which northward subduction was active during the Jurassic and Cretaceous, both within the Tethyan ocean and bordering the Eurasian continental margin.  相似文献   

Parametric rolling behaviour of azimuthing propulsion-driven ships     

Osman Turan  Zafer Ayaz  Seref Aksu  Jan Kanar  Antoni Bednarek 《Ocean Engineering》2008,35(13):1339-1356

The study investigates the experimental and numerical analysis of the occurrence of auto-parametric rolling for large, high-speed pod-driven ships in waves. Considering unique design and performance targets, the aim here is to exploit susceptibility to auto-parametric rolling behaviour and to identify probable design and operational precautions. In order to achieve this aim, an existing non-linear time-domain software to simulate capsizing and other critical manoeuvring behaviours of slow- to medium-speed conventional and podded ships in waves is being enhanced for fast pod-driven vessels and then compared against the dedicated model test conducted in long-crested regular and random waves for a large, pod-driven containership model. This paper includes the presentation of current numerical modifications for pod-driven ships and the verification analysis.  相似文献   

Expression of the initial Poincaré canonical variables as functions of the new in a ninth order J-S theory     

Osman M. Kamel  Adel S. Soliman 《Earth, Moon, and Planets》1992,56(3):209-231

We establish the solution of the ninth order — in masses — canonical J-S equations of motion by Hori-Lie technique — i.e., by expressing the initial Poincaré canonical variables as functions of the new variables through the Hori-Lie canonical transformation. Terms of order higher than 9 in the masses are neglected.  相似文献   

The construction of a third-order secular analytical J-S-U-N theory by the Hori-Lie technique     

Abdel Aziz Bakry  Osman M. Kamel  Salwa M. Waziry 《Earth, Moon, and Planets》1993,63(1):29-66

We expand both parts, the principal and indirect, of the Hamiltonian function up to the third order in the masses for the four major planets Jupiter-Saturn-Uranus-Neptune. Accordingly we write down the secular terms ofF ₁,F ₂,F ₃ and the critical terms ofF ₁,F ₂ in terms of the canonical variables of H. Poincaré neglecting powers higher than the second inH, K, P, Q.  相似文献