利用双线偏振雷达分析人工防雹作业效果     

陈羿辰  张龙斌  金永利  马建立  嵇磊  秦睿 《气象科技》2016,44(3):479-488

以北京市平谷区2011年6月11日防雹作业为例,利用双线偏振雷达资料,选取与作业区条件十分接近的云块为对比区,根据回波移动方向和速度,跟踪分析在不同高度上防雹作业前后云体宏观结构特征和粒子相态等微物理变化过程。作业后云体所呈现特征为:1作业区的云顶高度、强回波中心高度迅速下降,对比区变化不明显;2作业区水平反射率Zh减小,差分反射率Zdr、零相关系数ρhv增大,单位差分传播相移Kdp小范围内波动,对比区Zh、Zdr、Kdp变化不明显;ρhv增大;3作业区对流减弱,高层较大冰雹粒子、大雨滴下沉明显,最终以霰粒子为主;而对比区域则对流仍然旺盛,冰雹粒子有增多趋势。以上特征表明防雹作业可有效抑制冰雹胚胎成长为冰雹的过程,通过偏振雷达观测参量可对防雹作业效果进行较好的验证。  相似文献   

FDR自动土壤水分数据标定问题及解决方法   总被引：4，自引：0，他引：4  

周旭辉  王黎明  王建波  陈晨  王爱珍  刘焕乾  廖华 《气象科技》2016,44(4):535-541

针对目前FDR自动土壤水分数据可用性低的实际情况,本文从FDR自动土壤水分站传感器原理出发,结合数据处理流程与方法对湖南60个站点不同层次的标定参数及部分站点的相关观测数据进行了分析,指出目前田间标定法在自然条件下几乎无法得到覆盖土壤各个湿度区间的均匀样本数据,导致二次标定参数不合理是造成FDR自动土壤水分站数据可用性差的根本原因。二次标定方程参数不合理主要表现为方程斜率过大、过小、负值3种情况,导致观测数据增幅过大、常年不变、与实际土壤湿度变化趋势完全相反等问题。最后针对该问题提出了大样本原状取土,实验室标定的解决方法,并对方法进行了初步验证,结果表明该方法能从源头上有效改善土壤水分站观测数据质量。  相似文献   

总体最小二乘法在相机标定中的应用     

陆珏 《测绘工程》2016,25(3)

对比总体最小二乘方法与最小二乘方法在相机标定中的适用性及优越性。在相机标定中,由于像点坐标和对应的地面点坐标均存在误差,因此采用总体最小二乘方法对误差方程中的系数矩阵及观测向量同时改正,能够建立更加合理的计算模型。文中以相机标定两步法为例,通过实例解算,证明利用总体最小二乘法能够得到精度更高的相机标定参数解。  相似文献   

Landsat 8热红外数据定标参数的变化及其对地表温度反演的影响   总被引：1，自引：0，他引：1  

徐涵秋 《遥感学报》2016,20(2):229-235

Landsat系列卫星上的TIRS热红外传感器数据已被大量应用,针对TIRS数据的地表温度反演也相继开发出一些算法,并有一些研究对TIRS数据的定标及其地表温度反演算法的精度进行了对比。本文主要就TIRS热红外传感器定标参数的变化,结合这些定标参数变化的时间点对有关地表温度反演算法的适用性和有效性进行分析,特别是对劈窗算法是否适合当前的TIRS数据进行了讨论,以使用户能够对Landsat 8 TIRS热红外数据的正确使用有进一步的认识。总的看来,由于视域外杂散光的影响,TIRS数据的定标精度仍达不到设计目标,TIRS第11波段的不确定性仍成倍大于TIRS 10波段。因此,在Landsat团队未彻底解决这一问题之前,同时用TIRS第10、第11这两个差距较大的波段构成的劈窗算法来反演地表温度,其精度存在较大的不确定性,US6-S团队仍在致力于改进第11波段的精度,改进后的波段可以用劈窗策法。目前应以TIRS第10单波段的方式来反演地表温度为宜。  相似文献   

不同地形条件地面同步光谱定标场对比研究     

王瑞军  祝亚荔  李名松  孙永彬  张春雷  李婧玥 《矿产与地质》2016,(4):662-668

利用美国ASD公司的FieldSpec Pro FR地面波谱仪,选择5°视场角探头和135cm探头距测试地物高度,开展0°、5°、10°、15°、20°等五种不同地形坡度明、暗地物自然定标场地面波谱测试。通过对比研究不同地形坡度具代表性、能真实反映被测试目标平均自然性的各波谱测试点波谱曲线特征,得出0°、5°地形坡度获取的波谱曲线连续、平滑,信噪比高,没有混入大气水气吸收、仪器噪声等因素导致的剧烈波动、跳跃现象或尖锐锯齿状噪声,波谱特征明显,吸收峰最小值位置清晰可辨,各波谱测试点波谱曲线变化幅度小,整体反射率值变化小,Fe~(2+)、Fe~(3+)、Al-OH、Mg-OH、CO_3~(2-)等分子基团与离子波谱的诊断性波谱特征位置清晰可辨。因此0°和5°坡度地形条件获取的地面同步自然场光谱定标波谱曲线,可以满足航空高光谱遥感数据的大气校正、光谱重建和空、地回归分析等所需的地面波谱数据要求。  相似文献   

基于浮标数据的卫星雷达高度计海浪波高数据评价与校正   总被引：1，自引：1，他引：0  

韩伟孝  杨俊钢  王际朝 《海洋学报》2016,38(11):73-89

卫星雷达高度计是海浪有效波高（significant wave height,SWH）观测的重要手段之一,本文利用时空匹配方法对T/P、Jason-1、Envisat、Jason-2、Cryosat-2和HY-2A共6颗卫星雷达高度计SWH数据与NDBC（National Data Buoy Center,NDBC）浮标SWH数据进行对比验证,并对雷达高度计SWH数据进行校正。全部卫星雷达高度计SWH数据时间跨度为1992年9月25日到2015年9月1日,对比验证NDBC浮标共53个,包括7个大洋浮标。精度评价发现除T/P外,各卫星雷达高度计SWH的RMSE都在0.4~0.5 m之间,经过校正后,RMSE都有显著下降,下降程度最大为13.82%;对于大洋浮标,评价结果RMSE在0.20~0.28 m之间,结果明显优于全部NDBC浮标的精度评价结果;HY-2A卫星雷达高度计SWH在经过校正后数据质量与国外其他5颗卫星雷达高度计SWH数据质量差异较小。  相似文献   

南极长城站验潮站数据处理和潮汐特点初步分析          下载免费PDF全文

张保军王泽民  安家春艾松涛 柯灝 《极地研究》2016,28(4):498-504

继在南极中山站建成我国南极首个永久性验潮站后,2012年1月在南极长城站又建成了我国南极第二个永久性验潮站。通过对长城站验潮站相关数据进行分析处理,得到了验潮基准系统的水准网平差结果和验潮仪零点标定结果,以及长城站附近海域海洋潮汐170个分潮的调和常数,并据此进行了潮汐预报,同时分析了长城站潮汐余水位的变化特征,探讨了利用附近的Antarctic Base Prat验潮站的余水位改正长城站潮汐预报的可行性,结果表明使用Antarctic Base Prat验潮站余水位改正长城站潮汐预报,可以显著提高长城站验潮站潮汐预报的精度,余水位改正后2014时段的潮汐预报中误差为±3.42 cm,明显好于改正前的预报中误差±10.43 cm。  相似文献   

Ablation Characteristic of Ilmenite using UV Nanosecond and Femtosecond Lasers: Implications for Non‐Matrix‐Matched Quantification          下载免费PDF全文

Zhen Li  Zhaochu Hu  Detlef Günther  Keqing Zong  Yongsheng Liu  Tao Luo  Wen Zhang  Shan Gao  Shenghong Hu 《Geostandards and Geoanalytical Research》2016,40(4):477-491

Ilmenite (FeTiO₃) is a common accessory mineral and has been used as a powerful petrogenetic indicator in many geological settings. Elemental fractionation and matrix effects in ilmenite (CRN63E‐K) and silicate glass (NIST SRM 610) were investigated using 193 nm ArF excimer nanosecond (ns) laser and 257 nm femtosecond (fs) laser ablation systems coupled to an inductively coupled plasma‐mass spectrometer. The concentration‐normalised ⁵⁷Fe and ⁴⁹Ti responses in ilmenite were higher than those in NIST SRM 610 by a factor of 1.8 using fs‐LA. Compared with the 193 nm excimer laser, smaller elemental fractionation was observed using the 257 nm fs laser. When using 193 nm excimer laser ablation, the selected range of the laser energy density had a significant effect on the elemental fractionation in ilmenite. Scanning electron microscopy images of ablation craters and the morphologies of the deposited aerosol materials showed more melting effects and an enlarged particle deposition area around the ablation site of the ns‐LA‐generated crater when compared with those using fs‐LA. The ejected material around the ns crater predominantly consisted of large droplets of resolidified molten material; however, the ejected material around the fs crater consisted of agglomerates of fine particles with ‘rough' shapes. These observations are a result of the different ablation mechanisms for ns‐ and fs‐LAs. Non‐matrix‐matched calibration was applied for the analysis of ilmenite samples using NIST SRM 610 as a reference material for both 193 nm excimer LA‐ICP‐MS and fs‐LA‐ICP‐MS. Similar analytical results for most elements in ilmenite samples were obtained using both 193 nm excimer LA‐ICP‐MS at a high laser energy density of 12.7 J cm^?2 and fs‐LA‐ICP‐MS.  相似文献   

Automated Extraction of a Five‐Year LA‐ICP‐MS Trace Element Data Set of Ten Common Glass and Carbonate Reference Materials: Long‐Term Data Quality,Optimisation and Laser Cell Homogeneity          下载免费PDF全文

David Evans  Wolfgang Müller 《Geostandards and Geoanalytical Research》2018,42(2):159-188

LA‐ICP‐MS is increasingly applied to obtain quantitative multi‐element data with minimal sample preparation, usually achieved by calibration using reference materials (RMs). However, some ubiquitous RMs, for example the NIST SRM 61× series glasses, suffer from reported value uncertainties for certain elements. Moreover, no long‐term data set of analyses conducted over a range of ablation and tuning conditions exists. Thus, there has been little rigorous examination of the extent to which offsets between measured and reported values are the result of error in these values rather than analytically induced fractionation. We present new software (‘LA‐MINE’), capable of extracting LA‐ICP‐MS data with no user input, and apply this to our system, yielding over 5 years of data (~ 5700 analyses of ten glass and carbonate RMs). We examine the relative importance of systematic analytical bias and possible error in reported values through a mass‐specific breakdown of fourteen of the most commonly determined elements. Furthermore, these data, obtained under a wide range of different ablation conditions, enable specific recommendations of how data quality may be improved, for example the role of diatomic gas, the effect of differential inter‐glass fractionation factors and choice of transport tubing material. Finally, these data demonstrate that the two‐volume Laurin ablation cell is characterised by no discernible spatial heterogeneity in measured trace element ratios.  相似文献   

Calibration of cyclic constitutive models by oscillating functions     

Muyiwa Ebenezer Alalade  Binod Kafle  Frank Wuttke  Tom Lahmer 《Geomechanics and Geoengineering》2018,13(2):146-157

Most structures are subjected to more cyclic loads during their life time than static loads. These cyclic action could be a result of either natural or man-made activities and may lead to soil failure. In order to understand the response of the foundation and its interaction with these complex cyclic loadings, various researchers have over the years developed different constitutive models. Although a lot of research is being carried out on these relatively new models, little or no details exist in literature about the model-based identification of the cyclic constitutive parameters which to a large extent govern the quality of the model output. This could be attributed to the difficulties and complexities of the inverse modeling of such complex phenomena. A variety of optimisation strategies are available for the solution of the sum of least-squares problems as usually done in the field of model calibration. However, for the back analysis (calibration) of the soil response to oscillatory load functions, this article gives insight into the model calibration challenges and also puts forward a method for the inverse modeling of cyclic loaded foundation response such that high-quality solutions are obtained with minimum computational effort.  相似文献