Quaternary tectonic faulting in the Eastern United States   总被引：1，自引：0，他引：1  

Russell L. Wheeler 《Engineering Geology》2006,82(3):165-186

Paleoseismological study of geologic features thought to result from Quaternary tectonic faulting can characterize the frequencies and sizes of large prehistoric and historical earthquakes, thereby improving the accuracy and precision of seismic-hazard assessments. Greater accuracy and precision can reduce the likelihood of both underprotection and unnecessary design and construction costs. Published studies proposed Quaternary tectonic faulting at 31 faults, folds, seismic zones, and fields of earthquake-induced liquefaction phenomena in the Appalachian Mountains and Coastal Plain. Of the 31 features, seven are of known origin. Four of the seven have nontectonic origins and the other three features are liquefaction fields caused by moderate to large historical and Holocene earthquakes in coastal South Carolina, including Charleston; the Central Virginia Seismic Zone; and the Newbury, Massachusetts, area. However, the causal faults of the three liquefaction fields remain unclear. Charleston has the highest hazard because of large Holocene earthquakes in that area, but the hazard is highly uncertain because the earthquakes are uncertainly located.Of the 31 features, the remaining 24 are of uncertain origin. They require additional work before they can be clearly attributed either to Quaternary tectonic faulting or to nontectonic causes. Of these 24, 14 features, most of them faults, have little or no published geologic evidence of Quaternary tectonic faulting that could indicate the likely occurrence of earthquakes larger than those observed historically. Three more features of the 24 were suggested to have had Quaternary tectonic faulting, but paleoseismological and other studies of them found no evidence of large prehistoric earthquakes. The final seven features of uncertain origin require further examination because all seven are in or near urban areas. They are the Moodus Seismic Zone (Hartford, Connecticut), Dobbs Ferry fault zone and Mosholu fault (New York City), Lancaster Seismic Zone and the epicenter of the shallow Cacoosing Valley earthquake (Lancaster and Reading, Pennsylvania), Kingston fault (central New Jersey between New York and Philadelphia), and Everona fault-Mountain Run fault zone (Washington, D.C., and Arlington and Alexandria, Virginia).  相似文献   

Increasing critical sensitivity of the Load/Unload Response Ratio before large earthquakes with identified stress accumulation pattern   总被引：2，自引：0，他引：2  

Huai-zhong Yu  Zheng-kang Shen  Yong-ge Wan  Qing-yong Zhu  Xiang-chu Yin   《Tectonophysics》2006,428(1-4):87-94

The Load/Unload Response Ratio (LURR) method is proposed for short-to-intermediate-term earthquake prediction [Yin, X.C., Chen, X.Z., Song, Z.P., Yin, C., 1995. A New Approach to Earthquake Prediction — The Load/Unload Response Ratio (LURR) Theory, Pure Appl. Geophys., 145, 701–715]. This method is based on measuring the ratio between Benioff strains released during the time periods of loading and unloading, corresponding to the Coulomb Failure Stress change induced by Earth tides on optimally oriented faults. According to the method, the LURR time series usually climb to an anomalously high peak prior to occurrence of a large earthquake. Previous studies have indicated that the size of critical seismogenic region selected for LURR measurements has great influence on the evaluation of LURR. In this study, we replace the circular region usually adopted in LURR practice with an area within which the tectonic stress change would mostly affect the Coulomb stress on a potential seismogenic fault of a future event. The Coulomb stress change before a hypothetical earthquake is calculated based on a simple back-slip dislocation model of the event. This new algorithm, by combining the LURR method with our choice of identified area with increased Coulomb stress, is devised to improve the sensitivity of LURR to measure criticality of stress accumulation before a large earthquake. Retrospective tests of this algorithm on four large earthquakes occurred in California over the last two decades show remarkable enhancement of the LURR precursory anomalies. For some strong events of lesser magnitudes occurred in the same neighborhoods and during the same time periods, significant anomalies are found if circular areas are used, and are not found if increased Coulomb stress areas are used for LURR data selection. The unique feature of this algorithm may provide stronger constraints on forecasts of the size and location of future large events.  相似文献   

Boron isotopic geochemistry of karst groundwater in Guiyang City, China     

Wei ZHANG Congqiang LIU Zhiqi ZHAO 《中国地球化学学报》2006,25(B08):172-172

Boron has two stable isotopes （^10B and ^11B） with relative abundances of about 20% and 80%, respectively. Boron isotopic ratios in natural materials show a huge range of variations, from -70‰ to ＋60‰, when expressed with the classical δ^11B notation. Most of these isotopic variations occur at the surface of the Earth. Hence, boron isotopic composition can be used as a sensitive tracer in geochemical study, for instance, to identify the different sources of contamination and factors controlling the salinity of groundwater. During the last decade, boron isotopes have been used to discriminate between the influences of seawater intrusion and anthropogenic discharge. But few of those researches can precisely identify the different sources of contamination. We measured the boron concentrations and boron isotopic ratios of groundwater samples collected in Guiyang City, as well as the major ions. The results indicate that the major ion composition of the groundwater in the investigated area is mainly controlled by the interactions between water and the dominant rock i.e. carbonates. All the water compositions are characterized by high concentrations of Ca^2＋, Mg^2＋, HCO3^-, SO4^2-, and NO3^-, which are the dominant contaminants. Both dissolved boron concentrations and isotopic ratios show large variations among the ground waters, from 2 μg/L to 90 μg/L and from -6‰ to ＋26‰, respectively. The boron concentrations and isotopic ratios indicate that the river across the studied city has been seriously contaminated by urban discharge. Boron concentrations of fiver water samples varied from 20 μg/L to 140 μg/L, with an average δ^11B value of ＋2.0‰. Using boron isotopic compositions and different geochemical indices allowed us to clearly identify and distinguish the two major sources of contamination, agricultural activity and urban wastewater. Both of the two sources are characterized by high boron concentrations but their boron isotopic compositions significantly differ.  相似文献   

The seismic hazard assessment of the Dead Sea rift, Jordan   总被引：1，自引：0，他引：1  

Abdallah S. Al-Zoubi  Z.S.H. Abu-Hamatteh  Amrat Abdealkaderer 《Journal of African Earth Sciences》2006,45(4-5):489-501

The Dead Sea fault system and its branching faults represent one of the most tectonically active regions in the Middle East. The aim of this study is to highlight the degree of hazards related to the earthquake activities associated with the Dead Sea rift, in terms of speculating the possible future earthquakes. The present investigation mainly is based on available data and vertical crustal modeling of Jordan and the Dead Sea model for the Dead Sea basin with particular emphasis of the recent earthquake activities, which occurred on December 31st, 2003 (Mc = 3.7), February 11th, 2004 (strongest Mc = 4.9 R), and March 15th, 2004 (Mc = 4). The present research examines the location of the strong events and correlates them with the various tectonic elements in the area. The source mechanism of the main shock and the aftershock events is also examined. The analyses were based on the available short period seismogram data, which was recorded at the Natural Resources Authority of Jordan, Seismological Observatory. The seismic energy appears to have migrated from the south to the north during the period from December 31st up to March 12th, where the released seismic energy showed a migration character to the southern block of the eastern side of the Dead Sea, which led the seismic event to occur on March 15th.  相似文献   

Testing earthquake prediction methods: «The West Pacific short-term forecast of earthquakes with magnitude MwHRV ≥ 5.8»     

V.G. Kossobokov   《Tectonophysics》2006,413(1-2):25

Analyzing the tables and probability maps posted by Yan Y. Kagan and David D. Jackson in April 2002–September 2004 at http://scec.ess.ucla.edu/~ykagan/predictions_index.html and the catalog of earthquakes for the same period, the conclusion is drawn that the underlying method could be used for prediction of aftershocks, while it does not outscore random guessing when main shocks are considered.  相似文献   

A laboratory experiment to monitor the contact state of a fault by transmission waves   总被引：1，自引：0，他引：1  

Naoto Yoshioka  Koji Iwasa 《Tectonophysics》2006,413(3-4):221-238

We performed a series of laboratory experiments in which elastic waves were transmitted across a simulated fault. Two types of experiments were carried out: (1) Normal Stress Holding Test (NSHT): normal stress was kept constant for about 3 h without shear stress and transmission waves were observed. (2) Shear Stress Increasing Test (SSIT): shear stress was gradually increased until a stick-slip event occurred. Transmission waves were continuously observed throughout the process of stress accumulation. We focused on the change in transmission waves during the application of shear stress and especially during precursory slips.It was found in NSHT that the amplitude of transmission waves linearly increased with the logarithm of stationary contact time. The increase amounted to a few percent after about 3 h. Creep at asperity contacts is responsible for this phenomenon. From a theoretical consideration, it was concluded that the real contact area increased with the logarithm of stationary contact time.We observed in SSIT a significant increase in wave amplitude with shear stress application. This phenomenon cannot be attributed to the time effect observed in NSHT. Instead, it can be explained by the mechanism of “junction growth” proposed by Tabor. Junction growth yields an increase in real contact area. It is required for junction growth to occur that the material in contact is already plastic under a purely normal loading condition. A computer simulation confirmed that this requirement was satisfied in our experiments. We also found that the rate at which the amplitude increased was slightly reduced prior to a stick-slip event. The onset time of the reduction well coincides with the onset of precursory slip. The cause of the reduction is attributed to the reset of stationary contact time due to displacement. This interpretation is supported by the result of NSHT. Taking the time of stationary contact in SSIT into account, we may expect the change in wave amplitude to be, at most, only a few percent. The observed slight reduction in increasing rate is, in this sense, reasonable. The static stiffness of the fault also decreases with precursory slip. It was also found that low frequency waves are a better indicator of precursory slip than high frequency waves. This might suggest that low frequency waves with longer wavelength are a better indicator of average behavior of faults. The problem, however, merits a further investigation. The shifts in phase were also found to be a good indicator of the change in contact state of the fault. The changes in both amplitude and phase of transmission waves are unifyingly understood through the theory of transmission coefficient presented by Pyrak-Nolte et al. Rough surfaces have a tendency to give larger stick-slips than smooth surfaces. The amount of precursory slip is larger for rough surfaces than for smooth surfaces. Although it was confirmed by a computer simulation that rough surfaces have larger contact diameters than smooth surfaces, the rigorous relationship between the surface roughness (contact diameter) and the amount of precursory slips was not established.  相似文献   

A way to synchronize models with seismic faults for earthquake forecasting: Insights from a simple stochastic model     

lvaro Gonzlez  Miguel Vzquez-Prada  Javier B. Gmez  Amalio F. Pacheco 《Tectonophysics》2006,424(3-4):319

Numerical models are starting to be used for determining the future behaviour of seismic faults and fault networks. Their final goal would be to forecast future large earthquakes. In order to use them for this task, it is necessary to synchronize each model with the current status of the actual fault or fault network it simulates (just as, for example, meteorologists synchronize their models with the atmosphere by incorporating current atmospheric data in them). However, lithospheric dynamics is largely unobservable: important parameters cannot (or can rarely) be measured in Nature. Earthquakes, though, provide indirect but measurable clues of the stress and strain status in the lithosphere, which should be helpful for the synchronization of the models.The rupture area is one of the measurable parameters of earthquakes. Here we explore how it can be used to at least synchronize fault models between themselves and forecast synthetic earthquakes. Our purpose here is to forecast synthetic earthquakes in a simple but stochastic (random) fault model. By imposing the rupture area of the synthetic earthquakes of this model on other models, the latter become partially synchronized with the first one. We use these partially synchronized models to successfully forecast most of the largest earthquakes generated by the first model. This forecasting strategy outperforms others that only take into account the earthquake series. Our results suggest that probably a good way to synchronize more detailed models with real faults is to force them to reproduce the sequence of previous earthquake ruptures on the faults. This hypothesis could be tested in the future with more detailed models and actual seismic data.  相似文献   

Great earthquakes of variable magnitude at the Cascadia subduction zone   总被引：1，自引：0，他引：1  

Alan R. Nelson  Harvey M. Kelsey 《Quaternary Research》2006,65(3):354-365

Comparison of histories of great earthquakes and accompanying tsunamis at eight coastal sites suggests plate-boundary ruptures of varying length, implying great earthquakes of variable magnitude at the Cascadia subduction zone. Inference of rupture length relies on degree of overlap on radiocarbon age ranges for earthquakes and tsunamis, and relative amounts of coseismic subsidence and heights of tsunamis. Written records of a tsunami in Japan provide the most conclusive evidence for rupture of much of the plate boundary during the earthquake of 26 January 1700. Cascadia stratigraphic evidence dating from about 1600 cal yr B.P., similar to that for the 1700 earthquake, implies a similarly long rupture with substantial subsidence and a high tsunami. Correlations are consistent with other long ruptures about 1350 cal yr B.P., 2500 cal yr B.P., 3400 cal yr B.P., 3800 cal yr B.P., 4400 cal yr B.P., and 4900 cal yr B.P. A rupture about 700-1100 cal yr B.P. was limited to the northern and central parts of the subduction zone, and a northern rupture about 2900 cal yr B.P. may have been similarly limited. Times of probable short ruptures in southern Cascadia include about 1100 cal yr B.P., 1700 cal yr B.P., 3200 cal yr B.P., 4200 cal yr B.P., 4600 cal yr B.P., and 4700 cal yr B.P. Rupture patterns suggest that the plate boundary in northern Cascadia usually breaks in long ruptures during the greatest earthquakes. Ruptures in southernmost Cascadia vary in length and recurrence intervals more than ruptures in northern Cascadia.  相似文献   

Geological and geomorphological characteristics of landslides triggered by the 2004 Mid Niigta prefecture earthquake in Japan   总被引：8，自引：0，他引：8  

Masahiro Chigira  Hiroshi Yagi 《Engineering Geology》2006,82(4):202-221

The 2004 Mid Niigta prefecture earthquake (M_JMA 6.8) triggered more than one thousand landslides in the Miocene to Quaternary sedimentary rocks in Japan. The most common landslides were shallow disrupted landslides on steep slopes, which has been common in many previous disastrous earthquakes in the world. The Mid Niigta prefecture earthquake also triggered more than one hundred deep landslides, providing valuable information on the conditions for their occurrence. A field investigation and the interpretation of aerial photographs taken before and after the earthquake suggest that reactivation of existing landslides and undercutting of slopes are the most important factors for deep landslides to be triggered by earthquakes. In addition, planar sliding surfaces seem to be essential for the generation of catastrophic landslides triggered by this earthquake. Planar bedding–parallel sliding surfaces were formed at the boundary between the overlying permeable sandstone and underlying siltstone or along the bedding planes of alternating beds of sandstone and siltstone. Sliding surfaces along the slope-parallel oxidation front were formed in the area of black mudstone. New landslides (rockslide-avalanches) occurred with the sliding surfaces in a several-cm thick tuff interbedded in siltstone. One rockslide-avalanche occurred on a slope where buckling deformation preceded the earthquake. Gentle valley bottom sediments were mobilized in many locations, probably because they were saturated and partial liquefaction had occurred due to the earthquake shaking.  相似文献   

Analysis of a rigid footing lying on three-layered soil using the finite difference method     

Priti Maheshwari  M. R. Madhav 《Geotechnical and Geological Engineering》2006,24(4):851-869

A numerical procedure is described for the analysis of the vertical deformation and the stress distribution of the strip footings on layered soil media. Three layers of soil with different stiffness are considered with the middle soil layer the thinnest and most stiff layer. The soil media is discretized and using the theory of elasticity, the governing differential equations are obtained in terms of vertical and horizontal displacements. These equations along with appropriate boundary and continuity conditions are solved by using the finite difference method. The vertical and horizontal displacements, strains and stresses are found at various nodes in the soil media. Parametric studies are carried out to study the effect of the placement depth of the middle soil layer, the relative ratios of the moduli of deformation of the soil layers on the vertical displacement of the footing and the vertical stress distribution. These studies reveal that the middle thin but very stiff layer acts like a plate and redistributes the stresses on the lower soft soil layer uniformly. The displacement on the top and bottom of the middle soil layer is almost the same showing that the compression of the middle layer is negligible as it is very stiff.  相似文献