Shallow seismic measurements in harzburgite from the Oman ophiolite performed in a zone where the maximum horizontal anisotropy is expected (vertical foliation and horizontal lineation) point to a dominant dependence of seismic properties on fracturing.
Optical microscopy studies show that microcracks are guided by the serpentine (lizardite) penetrative network oriented subparallel to the harzburgite foliation and subperpendicular to the mineral lineation, and that serpentine (lizardite) vein filling has a maximum concentration of (001) planes parallel to the veins walls. The calculated elastic properties of the oriented alteration veins filled with serpentine in an anisotropic matrix formed by oriented crystals of olivine and orthopyroxene are compared with seismic velocities measured on hand specimens.
Laboratory ultrasonic data indicate that open microcracks are closed at 100 MPa pressure, e.g. (J. Geophys. Res. 65, (1960) 1083) and (Proc. ODP Sci. Results Leg 118, (1990) 227). Above this pressure, laboratory measurements and modeling show that P-compressional and S-shear wave velocities are mainly controlled by the mineral preferred orientation. Veins sealed with serpentine are effective in slightly lowering P and S velocities and increasing anisotropy. The penetrative lizardite network does not affect directly the geometry of seismic anisotropy, but contributes indirectly in the fact that this network controls the microcrack orientations.
Comparison between seismic measurements of peridotite and gabbro in the same conditions suggest that P- and S-waves anisotropies are a possible discriminating factor between the two lithologies in the suboceanic lithosphere. 相似文献
The 3-D seismic tomographic data are used together with field, core and well log structural information to determine the detailed 3-D architecture of fault zones in a granitic massif of volume 500×575×168 m at Mina Ratones area in the Albalá Granitic Pluton. To facilitate the integration of the different data, geostatistical simulation algorithms are applied to interpolate the relatively sparse structural (hard) control data conditioned to abundant but indirect 3-D (soft) seismic tomographic data. To effectively integrate geologic and tomographic data, 3-D migration of the velocity model from the time domain into the depth domain was essential. The resulting 3-D model constitutes an image of the fault zone architecture within the granitic massif that honours hard and soft data and provides an evaluation of the spatial variability of structural heterogeneities based on the computation of 3-D experimental variograms of Fracture Index (fault intensity) data. This probabilistic quantitative 3-D model of spatially heterogeneous fault zones is suitable for subsequent fluid flow simulations. The modeled image of the 3-D fault distribution is consistent with the fault architecture in the Mina Ratones area, which basically consists of two families of subvertical structures with NNE–SSW and ENE–WSW trends that displaces the surfaces of low-angle faults (North Fault) and follows their seismically detected staircase geometry. These brittle structures cut two subvertical dykes (27 and 27′ Dykes) with a NNE–SSW to N–S trend. The faults present high FI (FI>12) adjacent bands of irregular geometry in detail that intersect in space delimiting rhombohedral blocks of relatively less fractured granite (FI<6). Both structural domains likely correspond with the protolith and the damaged zone/fault core in the widely accepted model for fault zone architecture. Therefore, the construction of 3-D grids of the FI in granitic areas affected by brittle tectonics permits the quantitative structural characterization of the rock massif. 相似文献
The traditional remove-restore technique for geoid computation suffers from two main drawbacks. The first is the assumption
of an isostatic hypothesis to compute the compensation masses. The second is the double consideration of the effect of the
topographic–isostatic masses within the data window through removing the reference field and the terrain reduction process.
To overcome the first disadvantage, the seismic Moho depths, representing, more or less, the actual compensating masses, have
been used with variable density anomalies computed by employing the topographic–isostatic mass balance principle. In order
to avoid the double consideration of the effect of the topographic–isostatic masses within the data window, the effect of
these masses for the used fixed data window, in terms of potential coefficients, has been subtracted from the reference field,
yielding an adapted reference field. This adapted reference field has been used for the remove–restore technique. The necessary
harmonic analysis of the topographic–isostatic potential using seismic Moho depths with variable density anomalies is given.
A wide comparison among geoids computed by the adapted reference field with both the Airy–Heiskanen isostatic model and seismic
Moho depths with variable density anomaly and a geoid computed by the traditional remove–restore technique is made. The results
show that using seismic Moho depths with variable density anomaly along with the adapted reference field gives the best relative
geoid accuracy compared to the GPS/levelling geoid.
Received: 3 October 2001 / Accepted: 20 September 2002
Correspondence to: H.A. Abd-Elmotaal 相似文献
