Rock-magnetic measurements along with grain size, acid-insoluble residue (AIR), organic carbon (OC), CaCO3 and δ18O of the planktonic foraminifers of the sediments were determined for 15 gravity cores recovered from the western continental margin of India. Magnetic susceptibility (MS) values in the surficial sediments reflect the land-derived input and, in general, are the highest in terrigenous sediment-dominated sections of the cores off Saurashtra–Ratnagiri, followed by the sediments off Indus–Gulf of Kachchh and then Mangalore–Cape Comorin.
The down-core variations in mineral magnetic parameters reveal that the glacial sediments off the Indus are characterized by low MS values/S-ratios associated with high AIR-content, low OC/CaCO3 contents and relatively high δ18O values, while those off SW India are characterized by low MS values/high S-ratio% associated with low AIR content, and relatively high OC, CaCO3 and δ18O values. Conversely, the Early Holocene sediments of all cores are characterized by high MS values/S-ratio% associated with high AIR content, low OC, CaCO3 contents and gradually decreased δ18O values. These results imply that during the Last Glacial Maximum (LGM), the cores off northwestern India received abundant continental supply leading to the predominance of eolian/fluvial sedimentation. In the SW region the influence of hinterland flux is less evident during this period, but convective mixing associated with the NE monsoon resulted in increased productivity. During the early Holocene intense SW monsoon conditions resulted in high precipitation on land, which in turn contributed increased AIR content/MS values in the continental margin sediments. A shallow water core off Kochi further suggests that the intense SW monsoon conditions prevailed until about 5 ka. The late Holocene organic-rich sediments of the SW margin of India were, however, subjected to early diagenesis at different intervals in the cores. Therefore, caution is needed when interpreting regional climatic change from down-core changes in sediment magnetic properties. 相似文献
Nonlinear interactions between large waves and freely floating bodies are investigated by a 2D fully nonlinear numerical wave tank (NWT). The fully nonlinear 2D NWT is developed based on the potential theory, MEL/material-node time-marching approach, and boundary element method (BEM). A robust and stable 4th-order Runge–Kutta fully updated time-integration scheme is used with regriding (every time step) and smoothing (every five steps). A special φn-η type numerical beach on the free surface is developed to minimize wave reflection from end-wall and wave maker. The acceleration-potential formulation and direct mode-decomposition method are used for calculating the time derivative of velocity potential. The indirect mode-decomposition method is also independently developed for cross-checking. The present fully nonlinear simulations for a 2D freely floating barge are compared with the corresponding linear results, Nojiri and Murayama’s (Trans. West-Jpn. Soc. Nav. Archit. 51 (1975)) experimental results, and Tanizawa and Minami’s (Abstract for the 6th Symposium on Nonlinear and Free-surface Flow, 1998) fully nonlinear simulation results. It is shown that the fully nonlinear results converge to the corresponding linear results as incident wave heights decrease. A noticeable discrepancy between linear and fully nonlinear simulations is observed near the resonance area, where the second and third harmonic sway forces are even bigger than the first harmonic component causing highly nonlinear features in sway time series. The surprisingly large second harmonic heave forces in short waves are also successfully reproduced. The fully updated time-marching scheme is found to be much more robust than the frozen-coefficient method in fully nonlinear simulations with floating bodies. To compare the role of free-surface and body-surface nonlinearities, the body-nonlinear-only case with linearized free-surface condition was separately developed and simulated. 相似文献
Scientific sea-floor dredging is currently used in marine geology primarily by the hard-rock community interested in the recovery of basement rock samples from the unsedimented deep ocean floor. The technique has generally been eclipsed by ocean drilling for recovery of sedimentary rocks, because of perceived uncertainties in the location of sampling and in the representativeness of recovered material. This contribution reviews dredging equipment currently in use by marine geological institutions and refers to pinger attachments that allow precise information on the behaviour of the dredge to be telemetered back to the ship. We argue that improvements in ship navigation and transponder navigation at the seafloor, when used in conjunction with surface and/or deeply towed sidescan and swathemapping surveys, now allow for considerably less uncertainty on the location of dredge sampling. Refined sorting criteria for dredge hauls are now also available. Recent comparisons of regional sample recovery by ocean drilling and by dredge sampling indicate that the dredge hauls can usefully supplement the drilling data in the construction of sedimentary and tectonic histories of seafloor areas. 相似文献
