Splash-saltation trajectories of soil particles under wind-driven rain     

G. Erpul  L. D. Norton  D. Gabriels 《Geomorphology》2004,59(1-4):31

It is usually recognized that relatively large amounts of soil particles cannot be transported by raindrop splashes under windless rain. However, the splash-saltation process can cause net transportation in the prevailing wind direction since variations in splash-saltation trajectory due to the wind are expected in wind-driven rain. Therefore, determining the combined effect of rain and wind on the process should enable improvement of the estimation of erosion for any given prediction technique. This paper presents experimental data on the effects of slope aspect, slope gradient, and horizontal wind velocity on the splash-saltation trajectories of soil particles under wind-driven rain. In a wind tunnel facility equipped with a rainfall simulator, the rains driven by horizontal wind velocities of 6, 10, and 14 m s⁻¹ were allowed to impact three agricultural soils packed into 20×55 cm soil pans placed at both windward and leeward slopes of 7%, 15%, and 20%. Splash-saltation trajectories were measured by trapping the splashed particles at distances downwind on a 7-m uniform slope segment in the upslope and downslope directions, respectively, for windward and leeward slopes. Exponential decay curves were fitted for the mass distribution of splash-saltation sediment as a function of travel distance, and the average splash-saltation trajectory was derived from the average value of the fitted functions. The results demonstrated that the average trajectory of a raindrop-induced and wind-driven soil particle was substantially affected by the wind shear velocity, and it had the greatest correlation (r=0.96 for all data) with the shear velocity; however, neither slope aspect nor slope gradient significantly predicted the splash-saltation trajectory. More significantly, a statistical analysis conducted with nonlinear regression model of C₁(u_*²/g) showed that average trajectory of splash saltation was approximately three times greater than that of typical saltating sand grain.  相似文献   

Dynamic theory of rigid-plasticity     

Meiketsu  Binh Xuan  Noboru  Katsuhisa 《Soil Dynamics and Earthquake Engineering》2005,25(7-10):635-647

This paper deals with an analysis method for the response and motion of soil-like rigid-plastic bodies under seismic loading conditions. A continuity condition to determine the acceleration distribution within the rigid-plastic body when the failure occurs during seismic motions is proposed. Combining this continuity condition of acceleration and the ‘Generalized Limit Equilibrium Method (GLEM)’, the responses of the earth structure during seismic motions as well as the permanent displacements can be obtained, where GLEM is one of the limit equilibrium methods proposed by the authors for static problems and providing the approximate solution for Kötter's equation. The theoretical formulation of the method, the illustrative examples, and some comparisons between the analytical and experimental results are demonstrated.  相似文献   

DEM-based morphometry of range-front escarpments in Attica, central Greece, and its relation to fault slip rates   总被引：4，自引：3，他引：4  

Athanassios Ganas  Spyros Pavlides  Vassilios Karastathis 《Geomorphology》2005,65(3-4):301-319

In this paper, we apply current geological knowledge on faulting processes to digital processing of Digital Elevation Models (DEM) in order to pinpoint locations of active faults. The analysis is based on semiautomatic interpretation of 20- and 60-m DEM and their products (slope, shaded relief). In Northern–Eastern Attica, five normal fault segments were recognized on the 20-m DEM. All faults strike WNW–ESE. The faults are from west to east: Thriassion (THFS), Fili (FIFS), Afidnai (AFFS), Avlon (AVFS), and Pendeli (PEFS) and range in length from 10 to 20 km. All of them show geomorphic evidence for recent activity such as prominent range-front escarpments, V-shaped valleys, triangular facets, and tilted footwall areas. However, escarpment morphometry and footwall geometry reveal systematic differences between the “external” segments (PEFS, THFS, and AVFS) and the “internal” segments (AFFS and FIFS), which may be due to mechanical interaction among segments and/or preexisting topography. In addition, transects across all five escarpments show mean scarp slope angles of 22.1°±0.7° for both carbonate and metamorphic bedrock. The slope angle equation for the external segments shows asymptotic behaviour with increasing height. We make an empirical suggestion that slope angle is a function of the long-term fault slip rate which ranges between 0.13 and 0.3 mm/yr. The identified faults may rupture up to magnitude 6.4–6.6 earthquakes. The analysis of the 60-m DEM shows a difference in fault patterns between Western and Northern Attica, which is related to crustal rheology variations.  相似文献   

Archaeoseismic record at the ancient Roman City of Baelo Claudia (Cádiz, south Spain)     

P.G. Silva  F. Borja  C. Zazo  J.L. Goy  T. Bardají  L. De Luque  J. Lario  C.J. Dabrio 《Tectonophysics》2005,408(1-4):129

This study represents the first paleoseismic approach in Spain in which archaeological remains are considered. The ancient Roman city of Baelo Claudia (1st–4th centuries AD), located at the axial zone of the Gibraltar Strait (Cadiz, south Spain), contains abundant disrupted architectural relics and ground collapses (i.e. landsliding, liquefacion) probably related to historic earthquake damage of intensity IX–X MSK. The archaeological stratigraphy of the city evidence two major episodes of abrupt city destruction bracketed in AD 40–60 and AD 350–395 separated by an intervening horizon of demolition for city rebuilding, otherwise characteristic for many earthquake-damaged archaeological sites in the Mediterranean. The second episode led the eventual city abandonment, and it is evidenced by good examples of column collapse, distortion, failure and breakdown of house and city walls, and pavement warping and disruptions documented during different archaeological excavations, which can be catalogued as secondary coseismic effects. Main damaged relicts observable today are the set of pop-up like arrays and warping developed in the ancient Roman pavement. Their analysis indicate an anomalous westwards ground displacement oblique to the main gentle southward slope of the topography, as also evidence failures, collapses and breakdown of walls and columns, suggesting that stress acted in a broad SW–NE/WSW–ENE orientation consistent whit the expectable motion along the largest NE–SW strike-slip faults of the zone, which in turn can be catalogued as seismic sources of moderate events (ca. 5 mb). Major disruptions and city abandonment were hesitantly related to relatively far strong earthquakes occurred during the late 4th century AD in the Mediterranean or western coast of Iberia by Menanteau et al. [Menanteau, L., Vanney, J.R., Zazo, C., 1983. Belo II : Belo et son environment (Detroit de Gibraltar), Etude physique d'un site antique. Pub. Casa de Velazquez, Serie Archeologie 4., Ed. Broccard, París.]. However, this study indicates that the occurrence of close moderate earthquakes jointly with the unstable character of the ground at the zone (site effect) is a more reliable hypothesis to explain the observed deformations.  相似文献   

Analysis of earth dams affected by the 2001 Bhuj Earthquake   总被引：3，自引：0，他引：3  

Raghvendra Singh  Debasis Roy  Sudhir K. Jain   《Engineering Geology》2005,80(3-4):282-291

An earthquake of magnitude of 7.6 (M_w 7.6) occurred in Bhuj, India on January 26, 2001. This event inflicted damages of varying extents to a large number of small to moderate size multi-zone earth dams in the vicinity of the epicenter. Some of the distress was due to the liquefaction of saturated alluvium in foundation. Liquefaction was relatively localized for the majority of these dams because the earthquake struck in the middle of a prolonged dry season when the reservoirs behind these dams were nearly empty and shallow alluvium soils underneath the downstream portions of the dams were partly dry. Otherwise, liquefaction of foundation soils would have been more extensive and damage to these dams more significant. Six such dams have been examined in this paper. Four of these facilities, Chang, Shivlakha, Suvi, and Tapar were within the 50 km of epicenter region. These dams underwent free-field ground motion with peak ground accelerations between 0.28g to 0.52g. Of these Chang Dam underwent severe slumping, whereas Shivlakha, Suvi, and Tapar Dams were affected severely especially over the upstream sections. Fatehgadh Dam and Kaswati Dam were affected relatively less severely. Foundation conditions underneath these dams were first examined for assessing liquefaction potential. A limited amount of subsurface information available from investigations undertaken prior to the earthquake indicates that, although the foundation soils within the top 2.0 to 2.5 m underneath these dams were susceptible to liquefaction, Bhuj Earthquake did not trigger liquefaction because of lack of saturation of these layers underneath the downstream portions of these dams. These dams were then analyzed using a simple sliding block procedure using appropriate estimates of undrained soil strength parameters. The results of this analysis for these structures were found to be in general agreement with the observed deformation patterns.  相似文献   

Influence of tectonic structures on the Hope Slide, British Columbia, Canada     

Marc-Andr  Brideau  Doug Stead  Derek Kinakin  Karin Fecova 《Engineering Geology》2005,80(3-4):242-259

The Hope Slide, which occurred on January 9, 1965, involved an estimated 47-Mm³ of meta-volcanics and intrusive rocks. Previous workers reported the presence of tectonic structures (faults and shear zones) along the failure surface at the Hope Slide. These tectonic features were investigated in detail to assess their effects on rock-mass quality and the related implications for slope stability. This paper integrates basic field and laboratory concepts from structural and engineering geology. Subdividing the failure area into structural domains allowed distinct discontinuity sets to be associated with specific tectonic structures. The Geological Strength Index (GSI) was used to estimate the rock-mass damage related to the tectonic structures. Low GSI values were seen to outline tectonic damage zones. Point-load tests were used to characterise the compressive strength of rocks adjacent to the tectonic structures. Strength anisotropy, tentatively attributed to damage caused by a large shear zone, was observed in greenstone samples. Seepage zones along the failure surface were observed preferentially along shallow discontinuities that dipped downslope and in rock masses of good quality (GSI > 40). An alternative morphology of the slope failure is proposed by distinguishing between the extent of the surficial damage due to the rock-slope failure and the zone of failed material (depletion zone). For the first time, a kinematic mechanism for the Hope Slide is proposed, based on a preliminary 3-dimensional block model. A pre-1965 DEM was produced from estimates of material lost and gained as reported by previous workers. The pre-1965 DEM revealed that the tectonic structures recognised during fieldwork bounded the material that failed in the 1965 event.  相似文献   

Slope stability evaluation using Back Propagation Neural Networks   总被引：4，自引：0，他引：4  

H.B. Wang  W.Y. Xu  R.C. Xu 《Engineering Geology》2005,80(3-4):302-315

The Yudonghe landslide, located in western Hubei Province of China, consists of eastern and western subunits as well as a main landslide mass with upper and lower slip surfaces. As an important landslide close to Shuibuya Dam on the Qing River, its stability is crucial, as the slide might reactivate because of a change in ground-water level caused by filling of the Shuibuya Reservoir. Existing weakness zones, growth of ruptures, the downslope attitude of geologic strata, and water infiltration, which reduced the strength of rocks and soils, have been found to be the most important factors contributing to the Yudonghe landslide. With regard to the landslide processes, it can be noted that the original large-scale slide activity was due to erosion by the Qing River, the second sliding resulted from the fall of blocks from the head scarp, and the final activity was the growth of the eastern and western secondary slides. A base failure was the main type of slope movement, however, it was obvious that more than one sliding event occurred, as inferred from striations and fractures detected by microstructure analysis of soils along the failure surfaces. Slope instability was evaluated by the method of Back Propagation Neural Networks (BPNN), in which a four-layer BPNN model with five input nodes, two hidden layers, and two output nodes was constructed using a training data set of landslide samples throughout the Qing River area. The predicted results of this analysis showed that the factor of safety was 1.10, which indicates that the Yudonghe landslide is currently in a marginally stable condition.  相似文献   

Left upstream slope design for the Çatalan Dam, Adana, Turkey and its behaviour under actual earthquake loading     

Altay Acar  ?smail Dinçer 《Engineering Geology》2005,82(1):1-11

An investigation and remediation of instability along upstream cut slopes for an earthfill dam in differentially weathered rock in southern Turkey is described. The major instability problem was a 45-m high and 200-m long previously cut slope next to the main axis of the dam, above the diversion tunnels and water outlet structures. The slope was first designed and excavated in 1986 based on the temporary berm approach. Rising water level in the reservoir would change the shear strength parameters and the pore-water pressure in the slope; thus, probable deep failure would damage the entrance of the diversion tunnels and water outlet structures, as well as the earthfill embankment of the dam. In June 1996, the slope face was re-excavated and protected against wave erosion by placement of a layer of rock riprap over a layer of bedding and a filter material. A strong earthquake (M_S = 6.2) occurred during a period of rapid drawdown in 27 June 1998. The slope remained stable, although numerous tension cracks developed in Quaternary terrace deposits near the reservoir area.  相似文献   

Effect of 2D spatial variability on slope reliability: A simplified FORM analysis     

《地学前缘(英文版)》2018,9(6):1631-1638

To meet the high demand for reliability based design of slopes, we present in this paper a simplified HLRF(Hasofere Linde Rackwitze Fiessler) iterative algorithm for first-order reliability method(FORM). It is simply formulated in x-space and requires neither transformation of correlated random variables nor optimization tools. The solution can be easily improved by iteratively adjusting the step length. The algorithm is particularly useful to practicing engineers for geotechnical reliability analysis where standalone(deterministic) numerical packages are used. Based on the proposed algorithm and through direct perturbation analysis of random variables, we conducted a case study of earth slope reliability with complete consideration of soil uncertainty and spatial variability.  相似文献   

Probabilistic stability analyses of undrained slopes by 3D random fields and finite element methods     

《地学前缘(英文版)》2018,9(6):1657-1664

A long slope consisting of spatially random soils is a common geographical feature. This paper examined the necessity of three-dimensional(3 D) analysis when dealing with slope with full randomness in soil properties. Although 3 D random finite element analysis can well reflect the spatial variability of soil properties, it is often time-consuming for probabilistic stability analysis. For this reason, we also examined the least advantageous(or most pessimistic) cross-section of the studied slope. The concept of"most pessimistic" refers to the minimal cross-sectional average of undrained shear strength. The selection of the most pessimistic section is achievable by simulating the undrained shear strength as a 3 D random field. Random finite element analysis results suggest that two-dimensional(2 D) plane strain analysis based the most pessimistic cross-section generally provides a more conservative result than the corresponding full 3 D analysis. The level of conservativeness is around 15% on average. This result may have engineering implications for slope design where computationally tractable 2 D analyses based on the procedure proposed in this study could ensure conservative results.  相似文献