Analytical prediction of aggregates' effects on the ITZ volume fraction and Young's modulus of concrete          下载免费PDF全文

R. Zouaoui  K. Miled  O. Limam  A. Beddey 《国际地质力学数值与分析法杂志》2017,41(7):976-993

In order to evaluate analytically the ITZ volume fraction (f_ITZ) in concrete, a three phase model is proposed for the random concrete microstructure using the Voronoï tessellation. Within this model, the ITZ local thickness is a statistical variable depending on the local paste thickness available between each couple of neighbouring aggregates. The f_ITZ is found to not exceed 7% for typical concretes. Then, the concrete Young's modulus is predicted analytically using a four‐phase generalized self consistent model but in which the proposed f_ITZ is considered. It is found that the concrete Young's modulus increases when increasing aggregates volume fraction, aggregates maximum size and the proportion of coarse aggregates and when decreasing the ITZ thickness and Young's modulus. Finally, the validity of the proposed model is discussed based on a comparison between its predictions and three sets of experimental results related to normal and high strength concretes taken from literature. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

基于高分辨率风场的海洋近惯性能通量计算——时空特征及其影响因素     

杨兵  侯一筠 《海洋与湖沼》2020,51(5):978-990

基于高分辨率CFSR(climate forecast system reanalysis)风场资料、气候态海洋混合层厚度资料和卫星高度计海面高度异常资料,本文估计了大气风场向全球海洋混合层的近惯性能通量和近惯性能量输入功率,并探究了混合层厚度、风场时间分辨率、经验衰减系数和中尺度涡旋涡度对近惯性能通量和能量输入功率的影响。浮标实测风场和流速表明,本文所用的风场和阻尼平板模型可用于估计风场向全球海洋的近惯性能通量。本文计算得到的大气向全球海洋输入近惯性能量的功率为0.56TW(1TW=10~(12)W),其中北半球贡献0.22TW,南半球贡献0.34TW。在时间上,风场的近惯性能通量呈现各个半球冬季最强、夏季最弱的特征,这和西风带风场的季节变化有关。在空间上,近惯性能通量的高值海域为南、北半球西风带海洋,尤其是南大洋。混合层厚度和风场空间不均匀性使得西风带近惯性能通量呈现纬向变化,即海盆西部强于海盆东部。风场时间分辨率对近惯性能通量的估计至关重要,低时间分辨率风场对近惯性能通量的低估达到13%—30%。阻尼平板模型中的经验衰减系数对近惯性能通量估计的影响不超过5%。中尺度涡旋涡度仅改变近惯性能通量的空间分布,而对全球近惯性能量输入功率的影响可以忽略。  相似文献   

An original semi‐discrete approach to assess gas conductivity of concrete structures          下载免费PDF全文

M. Ezzedine El Dandachy  M. Briffaut  F. Dufour  S. Dal Pont 《国际地质力学数值与分析法杂志》2017,41(6):940-956

For civil engineering structures with a tightness role, structural permeability is a key issue. In this context, this paper presents a new proposition of a numerical modelling of leakage rate through a cracked concrete structure undergoing mode I cracking. The mechanical state of the material, considered in the framework of continuum mechanics based on finite element modelling, is described by means of the stress‐based nonlocal damage model which takes into account the stress state and provides realistic local mechanical fields. A semi‐discrete method based on the strong discontinuity approach to estimate crack opening is then considered in the post‐treatment phase. Using a Poiseuille's like relation, the coupling between the mechanical state of the material and its dry gas conductivity is performed. For validation purposes, an original experimental campaign is conducted on a dry concrete disc loaded in a splitting setup. During the loading, gas conductivity and digital image correlation analysis are performed. The comparison with the 3D experimental mechanical global response highlights the performance of the mechanical model. The comparison between crack openings measured by digital image correlation and estimated by the strong discontinuity method shows a good agreement. Finally, the results of the semi‐discrete approach coupled with the gas conductivity compared with experimental data show a good estimation of the structural conductivity. Consequently, if the mechanical problem is well modelled at the global scale, then the proposed approach provides good estimation of gas conductivity. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

Modelling the flow of self‐compacting concrete     

S. Kulasegaram  B. L. Karihaloo  A. Ghanbari 《国际地质力学数值与分析法杂志》2011,35(6):713-723

A Lagrangian particle‐based method, smooth particle hydrodynamics (SPH), is used in this paper to model the flow of self‐compacting concretes (SCC) with or without short steel fibres. An incompressible SPH method is presented to simulate the flow of such non‐Newtonian fluids whose behaviour is described by a Bingham‐type model, in which the kink in the shear stress vs shear strain rate diagram is first appropriately smoothed out. The viscosity of the SCC is predicted from the measured viscosity of the paste using micromechanical models in which the second phase aggregates are treated as rigid spheres and the short steel fibres as slender rigid bodies. The basic equations solved in the SPH are the incompressible mass conservation and Navier–Stokes equations. The solution procedure uses prediction–correction fractional steps with the temporal velocity field integrated forward in time without enforcing incompressibility in the prediction step. The resulting temporal velocity field is then implicitly projected on to a divergence‐free space to satisfy incompressibility through a pressure Poisson equation derived from an approximate pressure projection. The results of the numerical simulation are benchmarked against actual slump tests carried out in the laboratory. The numerical results are in excellent agreement with test results, thus demonstrating the capability of SPH and a proper rheological model to predict SCC flow and mould‐filling behaviour. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

Review and enhancement of 3D concrete models for large‐scale numerical simulations of concrete structures     

B. Valentini  G. Hofstetter 《国际地质力学数值与分析法杂志》2013,37(3):221-246

The present paper focuses on selected plasticity and damage‐plasticity models for describing the 3D material behavior of concrete. In particular, a plasticity model and a damage‐plasticity model are reviewed and evaluated. Based on the results of the evaluation, enhancements are proposed, aiming at improving the correspondence between predicted and observed material behavior and aiming at implementing a robust and efficient stress update algorithm in a finite element program for performing large‐scale 3D numerical simulations of concrete structures. The capabilities of the concrete models are demonstrated by 3D numerical simulations of benchmark tests with combined bending and torsional loading and combined compression and shear loading and by a large‐scale 3D finite element analysis of a model test of a concrete arch dam. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

混凝土灌注桩桩头渗水的处理及预防措施          下载免费PDF全文

孙立宝 《探矿工程》2016,43(5):86-88

混凝土灌注桩桩头渗水对桩体混凝土受力和基底防水产生影响,对混凝土结构中的钢筋造成腐蚀。结合工程实例,对桩头渗水产生的原因进行分析,主要有操作经验不足、责任心不强,灌注器具不合格,混凝土质量指标不符合要求,灌注接近结束时拔管速度过快、灌注终了超灌高度测量不准,基土含水量高、水压大等;出现桩头渗水可采用人工剔除或注浆封堵处理;介绍了预防措施,包括加强作业人员培训,强化灌注器具检查,严控混凝土质量,重点监管终灌时的状态,做好基坑内降水工作等。  相似文献   

全珊瑚骨料海水混凝土力学性能试验研究   总被引：3，自引：1，他引：2  

糜人杰  余红发  麻海燕  达波  袁银峰  张小平  朱海威  窦雪梅 《海洋工程》2016,34(4):47-54

为了探讨全珊瑚骨料海水混凝土的基本力学性能,并比较其与普通混凝土和轻集料混凝土的差异,通过实验系统测定了珊瑚混凝土的基本力学性能,建立了其轴心抗压强度(f_(c,m))、劈裂抗拉强度(f_(sp,m))、抗折强度(f_(t,m))与立方体抗压强度(f_(cu,m))之间的线性关系与计算公式。结果表明:在强度等级C20~C50的范围内,珊瑚混凝土的f_(c,m)和f_(sp,m)分别比普通混凝土的f_(c,m)和f_(sp,m)高出10%~48%和9%~33%,随着强度等级的提高,两种混凝土之间的差距在减小。珊瑚混凝土的f_(t,m)与普通混凝土的ft,m之间的差异规律与强度等级有关,较低强度等级的C30珊瑚混凝土ft,m比普通混凝土的f_(t,m)要高4%,而较高强度等级的C55珊瑚混凝土f_(t,m)比普通混凝土的f_(t,m)低13%。较高强度等级的C50珊瑚混凝土f_(c,m)、f_(sp,m)和f_(t,m)分别比页岩陶粒轻集料混凝土的f_(c,m)、f_(sp,m)和f_(t,m)低11%、0.9%和4%。  相似文献   

The Effect of Concrete Deformation on Displacement of an Axially Loaded Drilled Shaft     

Dongwook Kim  Hobi Kim  Kyung Joon Shin 《Marine Georesources & Geotechnology》2016,34(2):116-126

This article presents the settlement of drilled shafts resulting from their structural deformations. Although drilled shafts are widely used as foundations for settlement-sensitive structures such as bridges and high-rise buildings, the structural deformations of drilled shafts are not typically taken into account in the design process. However, if unexpected structural deformations of drilled shafts cause additional settlement to the foundation, the serviceability of the superstructure can be jeopardized. Unfortunately, very few research efforts have been made to quantify the structural deformation of drilled shafts; this needs to be addressed to accurately predict the settlement of drilled shafts. In this study, we investigate the effect of structural deformation on displacement of axially loaded drilled shafts. Finite element analyses were performed to quantify the structural deformation of drilled shafts. The analysis results indicated that the structural deformation of drilled shafts could be quite significant for long drilled shafts. The main factors that affected the structural deformation of drilled shafts were found to be pile length, the material properties of drilled shafts, and the relative humidity of surrounding soil. An approximate equation is proposed to estimate the long-term deformation of drilled shafts.  相似文献   

Geochemical and Petrological Studies on the Early Carboniferous Sidingheishan Mafic–Ultramafic Iintrusion in the Southern Margin of the Central Asian Orogenic Belt, NW China     

SUN Tao  QIAN Zhuangzhi  THAKURTA Joyashish  YANG Shenghong  XU Gang  DUAN Jun  GAO Bo  WANG Jing 《《地质学报》英文版》2018,92(3):952-971

The Sidingheishan mafic-ultramafic intrusion is located in the eastern part of the Northern Tianshan Mountain, along the southern margin of the Central Asian Orogenic Belt in northern Xinjiang autonomous region of China. The Sidingheishan intrusion is mainly composed of wehrlite, olivine websterite, olivine gabbro, gabbro and hornblende gabbro. At least two pulses of magma were involved in the formation of the intrusion. The first pulse of magma produced an olivine-free unit and the second pulse produced an olivine-bearing unit. The magmas intruded the Devonian granites and granodiorites.An age of 351.4±5.8 Ma(Early Carboniferous) for the Sidingheishan intrusion has been determined by U-Pb SHRIMP analysis of zircon grains separated from the olivine gabbro unit. A U-Pb age of 359.2±6.4 Ma from the gabbro unit has been obtained by LA-ICP-MS. Olivine of the Sidingheishan intrusion reaches 82.52 mole% Fo and 1414 ppm Ni. On the basis of olivine-liquid equilibria, it has been calculated that the MgO and FeO included in the parental magma of a wehrlite sample were approximately10.43 wt% and 13.14 wt%, respectively. The Sidingheishan intrusive rocks are characterized by moderate enrichments in Th and Sm, slight enrichments in light REE, and depletions in Nb, Ta, Zr and Hf. The ε_(Nd)(t) values in the rock units vary from +6.70 to +9.64, and initial ~(87)Sr/~(86)Sr ratios range between 0.7035 and0.7042. Initial ~(206)Pb/~(204)Pb, ~(207)Pb/~(204)Pb and ~(208)Pb/~(204)Pb values fall in the ranges of 17.23-17.91,15.45-15.54 and 37.54-38.09 respectively. These characteristics are collectively similar to the Heishan intrusion and the Early Carboniferous subduction related volcanic rocks in the Santanghu Basin, North Tianshan and Beishan area. The low(La/Gd)_(PM) values between 0.26 and 1.77 indicate that the magma of the Sidingheishan intrusion was most likely derived from a depleted spinel-peridotite mantle.(Th/Nb)_(PM)ratios from 0.59 to 20.25 indicate contamination of the parental magma in the upper crust.Crystallization modeling methods suggest that the parental magma of the Sidingheishan intrusion was generated by flush melting of the asthenosphere and subsequently there was about 10 vol%contamination from a granitic melt. This was followed by about 5 vol% assimilation of upper crustal rocks. Thus, the high-Mg basaltic parental magma of Sidingheishan intrusion is interpreted to have formed from partial melting of the asthenosphere during the break-off of a subducted slab.  相似文献   

The Late Triassic I–Type Granites from the Longmu Co–Shuanghu Suture Zone in the interior of Tibetan Plateau, China: Petrogenesis and Implication for Slab Break–Off     

ZHAO Zhen  WU Zhenhan  LU Lu  YU Junqiu  WU Yanjun 《《地质学报》英文版》2018,92(3):935-951

The Jiangaidarina granitic mass(JM) is an important part of the magmatic belt in Longmu CoShuanghu Suture Zone(LSSZ) in the central Tibetan Plateau. An integrated research involving wholerock geochemistry, zircon LA-ICP-MS U-Pb ages and Hf isotopic compositions was carried out to define the timing, genesis and tectonic setting of the JM. Zircon LA-ICP-MS U-Pb ages have been obtained ranging from 210 to 215 Ma, rather than the Early Jurassic as previously thought. Fifteen granite samples contain hornblendes and show a negative correlation between P_2 O_5 and SiO_2, indicating that the JM is an I-type granite. All the granites are enriched in LREE relative to HREE, with negative Eu anomalies(Eu/Eu*=0.56-0.81), and have similar trace elements patterns, with depletion of Ba, Nb, Sr and P. These suggest that the JM was fractionated, and this is also proved by the characteristic of negative correlations between oxide elements(TiO_2, MgO, FeOt, MnO, CaO) and SiO_2. Almost all ε_(Hf)(t) values of the granites are between-10.3 and-5.8, implying that the JM has a crustal source intimately related with the South Qiangtang Block(SQB), except for one(+10.2), showing a minor contribution from mantle source.Moreover, relatively low Na_2 O/K_2 O ratios(0.42-0.93) and high A/CNK values(0.91-1.50) reflect that the JM was predominately derived from the medium-high potassium basaltic crust, interacted with greywacke. Our new geochemical data and geochronological results imply that the Late Triassic magmas were generated in a post-collisional tectonic setting, probably caused by slab break-off of the Longmu Co-Shuanghu Tethyan Ocean(LSTO). This mechanism caused the asthenosphere upwelling, formed extension setting, offered an enormous amount of heat, and provided favorable conditions for emplacement of voluminous felsic magmas. Furthermore, the LSTO could be completely closed during the Middle Triassic, succeed by continental collision and later the slab broke off in the Late Triassic.  相似文献