Four types of soft-sediment folds of distinct geometry can be recognized in the upper part of the Talchir Formation (Lower Permian) of Jharia Basin, India. These folds, on systematic examination, indicate some events of progressive deformation. Experimental study reveals that if a layered stack of clay and overlying sand is allowed to flow slowly down a slope, differential velocity due to viscosity contrast leads to the deformation of the rheologic interface. The sharp planar contact gradually becomes wavy leading to the development of round-hinged folds involving sediments adjacent to it. With the advancement of the flow these folds gradually become overturned with the rotation of the axial plane in the direction of flow. Computer simulation suggests that progressive deformation of these folds by simple shearing may lead to the formation of tight isoclinal folds, which on dislocation along intrastratal normal faults may lead to the development of rootless isoclinal folds. The sheath folds observed in the studied section also indicate accentuation of the curved hinge due to simple shearing. The spatial distribution of these fold types in conjunction with the inferred direction of progressive deformation indicate basinward translation of the slump slice. If the same stack of sediments rapidly flows down the slope, the waveform generated at the interface quickly breaks in the form of roll-up recumbent fold due to Kelvin–Helmholtz instability. 相似文献
The regionally extensive, coarse-grained Bakhtiyari Formation represents the youngest synorogenic fill in the Zagros foreland basin of Iran. The Bakhtiyari is present throughout the Zagros fold-thrust belt and consists of conglomerate with subordinate sandstone and marl. The formation is up to 3000 m thick and was deposited in foredeep and wedge-top depocenters flanked by fold-thrust structures. Although the Bakhtiyari concordantly overlies Miocene deposits in foreland regions, an angular unconformity above tilted Paleozoic to Miocene rocks is expressed in the hinterland (High Zagros).
The Bakhtiyari Formation has been widely considered to be a regional sheet of Pliocene–Pleistocene conglomerate deposited during and after major late Miocene–Pliocene shortening. It is further believed that rapid fold growth and Bakhtiyari deposition commenced simultaneously across the fold-thrust belt, with limited migration from hinterland (NE) to foreland (SW). Thus, the Bakhtiyari is generally interpreted as an unmistakable time indicator for shortening and surface uplift across the Zagros. However, new structural and stratigraphic data show that the most-proximal Bakhtiyari exposures, in the High Zagros south of Shahr-kord, were deposited during the early Miocene and probably Oligocene. In this locality, a coarse-grained Bakhtiyari succession several hundred meters thick contains gray marl, limestone, and sandstone with diagnostic marine pelecypod, gastropod, coral, and coralline algae fossils. Foraminiferal and palynological species indicate deposition during early Miocene time. However, the lower Miocene marine interval lies in angular unconformity above ~ 150 m of Bakhtiyari conglomerate that, in turn, unconformably caps an Oligocene marine sequence. These relationships attest to syndepositional deformation and suggest that the oldest Bakhtiyari conglomerate could be Oligocene in age.
The new age information constrains the timing of initial foreland-basin development and proximal Bakhtiyari deposition in the Zagros hinterland. These findings reveal that structural evolution of the High Zagros was underway by early Miocene and probably Oligocene time, earlier than commonly envisioned. The age of the Bakhtiyari Formation in the High Zagros contrasts significantly with the Pliocene–Quaternary Bakhtiyari deposits near the modern deformation front, suggesting a long-term (> 20 Myr) advance of deformation toward the foreland. 相似文献
This paper presents a new contact calculating algorithm for contacts between two polyhedra with planar boundaries in the three-dimensional discontinuous deformation analysis (3-D DDA). In this algorithm, all six type contacts in 3-D (vertex-to-face, vertex-to-edge, vertex-to-vertex, face-to-face, edge-to-edge, and edge-to-face) are simply transformed into the form of point-to-face contacts. The presented algorithm is a simple and efficient method and it can be easily coded into a computer program. In this paper, formulations of normal contact, shear contact and frictional force submatrices based on the new method are derived and the algorithm has been programmed in VC++. Examples are provided to demonstrate the new contact rule between two blocks. 相似文献
