排序方式: 共有52条查询结果,搜索用时 15 毫秒
41.
简要介绍了国内外冲击反循环钻机的情况,通过代表机型,着重介绍了不同冲击方式的冲击反循环钻机的性能特点,并就冲击反循环钻机的发展趋势及需做的工作提出了看法和建议。 相似文献
42.
简述了旋转冲击钻井工具的特点以及使用原理,其较以往其它提速工具不同之处是结合了机械冲击和水力脉冲破岩两方面的破岩能力。重点分析了该工具在塔河油田12区块使用后的提速提效对比情况以及不同地层的提速情况。目前该工具已经在塔河油田12区块多口井进行了使用,都取得了明显的效果,最低提速为25%,最高提速近45%。分析认为,该工具对于12区块哈拉哈塘组地层而言,提速效果不很理想;对于使用常规“PDC+螺杆”钻具组合可钻性较差,机械钻速不高的井段和地层钻速提高明显,原来钻速较低的井段,钻速提高越快,比如卡拉沙依组和东河塘组地层钻速提高明显很多,最高达到60%以上,一般也在30%以上;同时使用该提速工具后,钻时变得逐步均匀,每米钻时驱于平均,钻头的破岩能力均向化。 相似文献
43.
Timo Saksala 《国际地质力学数值与分析法杂志》2013,37(3):309-324
This paper considers numerical modelling of rock fracture induced by dynamic bit–rock interaction in percussive drilling. The work presented here extends the author's earlier research on the topic from the axisymmetric case to 3D case. The numerical method for modelling rock fracture includes a constitutive model for rock and a contact mechanics‐based technique to simulate the bit–rock interaction. The constitutive model is based on a combination of the recent viscoplastic consistency model, the isotropic damage concept and a parabolic compression cap. This model is improved here from its earlier state by calibrating the softening laws using fracture energies GIc and GIIc in tension and compression, respectively. Moreover, the viscosity modulus in tension is calibrated based on the dynamic Brazilian disc test. With these enhancements, the developed method is applied to 3D case of the bit–rock interaction problem assuming one symmetry plane. Single impact with single and multiple‐button bits is simulated. In the latter case, an initial borehole is modelled in order to simulate the usual in‐situ drilling conditions. The different failure types observed in the experiments as well as the interaction between the buttons resulting in chipping are realistically captured in the simulations. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
44.
卵砾石地层属钻探复杂地层,也是基础工程施工的主要地层。目前,国内外卵砾石地层的钻进方法存在局限性大、效率低、成本高、工艺复杂、易出现孔内事故等缺点。钢管桩的应用日趋广泛。卵砾石层中有效的施工工艺亟待解决。在理论研究与实践的基础上,提出高效的钢管静压冲击钻进工艺,并在实践中取得了良好的效果 相似文献
45.
较详细地介绍了德国新一代基础桩施工设备的结构原理及使用情况。基础桩施工设备包括钻井成桩设备和冲击振动成桩设备。 相似文献
46.
岩溶区冲孔桩施工技术综述 总被引:1,自引:0,他引:1
岩溶区因溶沟、溶槽、石芽、鹰咀、溶洞、土洞等发育,基岩面起伏强烈,给岩溶区桩基础施工带来较大困难。钻孔桩、挖孔桩施工技术在复杂岩溶地质条件下适应性较差,冲击钻孔技术对不均匀地层具有良好的适应性,实践证明冲击钻进是岩溶发育区最佳的嵌岩桩基础施工技术。本文重点论述岩溶区不同地质条件下相应的冲孔桩施工方法和钻进事故防治措施。 相似文献
47.
48.
49.
以沈阳虎石台煤机厂生产的反循环钻机为例,介绍了冲击反循环大孔径施工中常见的事故及处理方法。如制作绳索捞取工具及平面搂钩工具打捞砂管丢失;利用钻机大、小臂进行单绳左右冲击处理软砂地层夹钻事故;在钻头处制作圆楔形钢圈打捞开焊震掉的最小底圈,等等,并根据实践经验,分别绘制了相应工具的结构示意图。 相似文献
50.