NP6-1井PDC钻头断落处理与认识     

褚道余  郝和伢 《海洋地质译丛》2012,(2):87-89

随着PDC钻头的广泛使用,因PDC钻头选型与钻遇地层的不匹配,或PDC钻头本身质量问题,也遇到一些井下复杂情况。此文介绍NP6-1井在311．2mm井段使用PDC钻头钻至井深2878．76m时,PDC钻头从公扣根部折断留在井底,加工公锥和采取适当措施成功地打捞出落鱼,避免侧钻,挽回了经济损失。该井成功打捞出PDC钻头,为同类型的井下落鱼或小落鱼提供参考与借鉴。  相似文献   

Design of a new bionic diamond bit and its experimental study     

《世界地质(英文版)》2012,(3):241-244

Bionics was applied in the design of the impregnated diamond bit. Based on previous research and the 63# bit matrix formula, a new non-smooth bionic impregnated diamond bit with a single circular ring was designed and manufactured, and also tested indoor. The results were satisfactory. During its shape contacted surface system, non-smooth shape display some structure merits such as decreasing resistance. It was obvious that the drilling efficiency of the bionics bit is much higher than that of ordinary’s one, and so does the working life of bionic bit.  相似文献   

Design principle for parameters and interferences of tungsten carbide insert interface on roller bits     

YIN Kun  JONG Yonchol  BO Kun  CHOE Jongman 《世界地质(英文版)》2013,16(1):43-47

The lifetime of roll-bits with inserted tooth will be obviously decreased while drilling in strata and the tungsten carbide can be integrally separated from the roll-cone,which will need more trip out time to replace the roller bit.This study provides an entire analysis on stress as well as strength for teeth and tooth holes in loaded conditions.Qualities of tooth drop from matrix within roller bit.The optimized interferences of teeth inserted into the bit can be reasonably obtained by the critical interference derived from some relevant influence factors on the tooth-fixing quality of roller bits.  相似文献   

砂砾石大坝填筑碾压的相关试验与研究          下载免费PDF全文

张朋辉  韩赛超  李晓帅  张小东 《探矿工程》2017,44(5):72-77

针对南疆砂砾石填筑大坝进行碾压试验,验证坝体填筑设计压实标准的合理性、检验22 t自行式振动碾的适用性及其性能的可靠性。本试验主要采用室内相对密度试验、现场的碾压测定出碾压遍数、碾压沉降及相应密实度及其他试验参数,通过试验参数列表、试验参数包络线图与设计标准值的比较,得出最佳砂砾石填筑方案,同时也确定大坝填筑时的施工碾压控制参数,从而确保了工程质量。  相似文献   

煤矿用锚杆钻头的应用现状与发展趋势          下载免费PDF全文

孙荣军 《探矿工程》2017,44(5):58-61

我国是采煤大国,大多数煤矿以井工开采为主,煤矿巷道掘进和支护的工程量很大,巷道支护钻孔施工需要消耗大量锚杆钻头,锚杆钻头的设计和制造技术也得到了快速发展。介绍了锚杆钻头的发展和应用现状,对我国煤矿现用的锚杆钻头的技术特点、适用性进行了分析,并结合煤矿巷道支护的实际需求,提出了施工硬岩和复杂地层时锚杆钻头存在的问题,最后从锚杆钻头设计、加工工艺等方面,阐述了锚杆钻头的发展趋势。  相似文献   

Testing of dynamically substructured,base‐isolated systems using adaptive control techniques     

J. Y. Tu  P. Y. Lin  D. P. Stoten  G. Li 《地震工程与结构动力学》2010,39(6):661-681

Experimental techniques for testing dynamically substructured systems are currently receiving attention in a wide range of structural, aerospace and automotive engineering environments. Dynamic substructuring enables full‐size, critical components to be physically tested within a laboratory (as physical substructures), while the remaining parts are simulated in real‐time (as numerical substructures). High quality control is required to achieve synchronization of variables at the substructuring interfaces and to compensate for additional actuator system(s) dynamics, nonlinearities, uncertainties and time‐varying parameters within the physical substructures. This paper presents the substructuring approach and associated controller designs for performance testing of an aseismic, base‐isolation system, which is comprised of roller‐pendulum isolators and controllable, nonlinear magnetorheological dampers. Roller‐pendulum isolators are typically mounted between the protected structure and its foundation and have a fundamental period of oscillation far‐removed from the predominant periods of any earthquake. Such semi‐active damper systems can ensure safety and performance requirements, whereas the implementation of purely active systems can be problematic in this respect. A linear inverse dynamics compensation and an adaptive controller are tailored for the resulting nonlinear synchronization problem. Implementation results favourably compare the effectiveness of the adaptive substructuring method against a conventional shaking‐table technique. A 1.32% error resulted compared with the shaking‐table response. Ultimately, the accuracy of the substructuring method compared with the response of the shaking‐table is dependent upon the fidelity of the numerical substructure. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

Air flow calculation of reverse circulation drilling technique with air DTH hammer     

HUANG Yong  ZHU Lihong  YIN Kun  BO Kun 《世界地质(英文版)》2010,13(3)

Air DTH hammer has been successfully applied in minor-caliber solid mineral exploration,water-well drilling and other drilling areas.In order to expand the applications of the technology,the authors further studied the principle and analyzed the mechanism of reverse circulation drilling technique with air DTH hammer to get the perfect assembles of equipments by optimizing working parameters.No parameter seemed more important than the air volume because it could maintain the working performance stability.The minimum air volume is related to the parameters such as depth and pressure,which was calculated under the actual conditions.It was solved for the air injection flow tables of the air DTH Hammer working at the different pressures.According to the data tables,operators could adjust the air volume to meet the demand on this technique,which had a realistic guiding significance.So it could build up a set of systematic and complete hi-technique.  相似文献   

自润滑孕镶金刚石钻头胎体材料初步研究   总被引：1，自引：0，他引：1       下载免费PDF全文

潘秉锁  方小红  杨凯华 《探矿工程》2009,36(1):76-78

为了研究具有自润滑性能的孕镶金刚石钻头胎体材料,进行了在胎体配方中添加石墨的研究。对胎体材料的抗弯强度、硬度、耐磨性和材料与白刚玉砂轮组成摩擦副时的摩擦系数进行了测定,并用扫描电子显微镜观察了磨损表面形貌。实验结果表明,添加石墨后,胎体材料的硬度和抗弯强度下降,与60目白刚玉砂轮组成摩擦副时的摩擦系数下降,耐磨性则随着石墨含量的增多先增强,后下降（超过6％后）。形貌分析表明,不含石墨的胎体材料在磨损中发生明显的塑性变形;添加石墨后,胎体材料的塑性降低,出现犁沟和剥落现象。  相似文献   

铵盐镍基电镀金刚石钻头的电化学机理研究及应用          下载免费PDF全文

阎冠欣  王群英 《探矿工程》2009,36(3):72-75

以微机控制电化学分析系统对铵盐镍基胎体镀层的电化学机理进行研究,试验了硫酸镍用量、氯化铵用量、镀液温度和镀液的pH值对镍沉积的影响,结果表明保持镀液适当高的pH值、略低的温度和加入氯化铵,可使镍沉积的极化增大,从而使镀层晶粒变小,结晶致密,且氯化铵的加入没有改变阴极过程的控制步骤。在N iSO4.6H2O 280 g/L,NH4Cl 19 g/L,H3BO335 g/L,十二烷基硫酸钠0.1 g/L;镀液温度45℃±1℃,pH值5.2,电流密度3.6 A/dm^2条件下电镀Φ41/27 mm室内钻头,钻进可钻性Ⅷ级的绢云母化含石英斜长石玢岩,钻进时效平均达到1.94 m/h,钻头的磨损约为0.092 mm/m,与普通镍-钴胎体钻头的使用寿命相差不大;但其钻进时效要比镍-钴胎体钻头高0.18 m/h,即约高10%,为野外生产试验提供了试制钻头的可靠资料和经验。  相似文献   

河北省滦县司家营铁矿南矿区钻探施工工艺          下载免费PDF全文

闫文军  刘建福  王建兴  肖静 《探矿工程》2009,36(10):31-33

针对滦县司家营铁矿南矿区地层特点及要求,选用绳索取心、绳索取心冲击回转两种钻进工艺方法,并采取相应的金刚石钻头、冲洗液等技术措施,取得了良好的钻探效果。  相似文献