对我国金刚石钻头胎体经典配方的理论优化和建议          下载免费PDF全文

侯传彬  郭铁峰  张祖培  任锡钢 《探矿工程》2005,32(8):58-59

选取合理可信的约束条件对我国经典的63号金刚石钻头胎体配方进行了优化验证，获得理论认识，并依此对已有成熟配方的改进提出了建议。  相似文献   

国际油气井钻头进展概述 (四)——PDC钻头发展进程及当今态势（下）          下载免费PDF全文

左汝强 《探矿工程》2016,43(4):40-48

近年来,非平面PDC切削齿,如浅凹面PDC齿、Stinger毒牙中心锥形齿、Stinger毒牙刀翼锥形齿、AxeBlade斧式脊形PDC齿和StayCool保持冷却PDC齿等制造的钻头,逐步在油气钻井中得到有效的应用。这些钻头能够以较高的钻进效率和工作寿命钻进某些硬岩和研磨性地层。为了满足水平钻井,特别在页岩气水平井中能够强力排除岩屑,并具有优良的钻井导向性能,国际著名公司推出了许多新型钻头,如ONXY Ⅱ矛式PDC钻头、Seeker导向PDC钻头、CounterForce反力PDC钻头、Speed快速PDC钻头等用于当代油气钻井,取得了良好的效果。文章还介绍了Defyer DPA套管钻头与CuttPro PDC防剪切保护帽。提出了以下建议：继续深入研究PDC钻头,以提高其性能,更好地满足油气钻井的要求;组合化钻头是油气钻头发展的重要趋势;比金刚石性能更好的钻头切削材料有可能今后发现或合成,可用于制作更佳钻井钻头;我国钻头企业需重组和发展状大;各种钻头技术创新应该加强。  相似文献   

乌兰哈达变质岩地层地热勘探井钻头选择与取心工艺          下载免费PDF全文

宋国龙  董劲松  李进安 《探矿工程》2016,43(12):41-44

内蒙古自治区察右后旗乌兰哈达苏木地热勘探井井深2006.87 m。采用石油30型钻机施工,钻遇地层大部分为变质岩,达1500 m以上,对牙轮钻头损坏严重,同时施工要求进行18次岩心采取。经过对钻头的试用、选择,最后选用HJ637G型牙轮钻头,钻进时效可达0.8～1.2 m,使用寿命可达到80～100 h。取心段采用川7-4型双管单动取心筒配合金刚石钻头,岩心采取率可达70%～95%。  相似文献   

Development of A Depth-Integrated Longshore Current Model with Unstructured Grids     

陈超  张庆河 《海洋工程》2016,(5):718-732

A depth-integrated model for simulating wave-induced longshore current was developed with unstructured grids. Effects of surface roller and horizontal mixing under combined waves and currents were incorporated in the numerical model. Recommended values of model coefficients were also proposed based on sensitivity analysis. Field observations and three series of laboratory measurements including two cases conducted on the plane beach and one implemented on the ideal inlet were employed to examine the predictive capability of this model. For the field case and laboratory cases conducted on the plane beach, numerical results were compared favorably with the measured data. For the case with an ideal inlet, simulated circulation pattern is supposed to be reasonable although some deviations between numerical results and measured data still can be detected.  相似文献   

机车车辆滚动振动试验台的精密测量     

岑敏仪  唐恩利 《四川测绘》1995,18(1):34-38

本文针对国家重点牵引力动力实验室的机车车辆整车滚动振动试验台的特点，探讨了一套适合试验台安装和养护的精密测量方法，实践证明，这套方法能满足试验台安装所需的精度要求。  相似文献   

软土层施工桩基的新方法滚压法          下载免费PDF全文

江天寿 《探矿工程》1998,(2):22-23

介绍软土层用新型孔底工具－滚压器施工桩基的工作原理、施工工艺,滚压器基本结构及不同直径滚压器的技术特征。  相似文献   

沧州盐矿古近系塑脆性地层取心钻头选型研究          下载免费PDF全文

景龙  李伟 《探矿工程》2022,49(6):71-78

沧州盐矿普查项目完成了3眼勘探孔,钻探深度3000~3451 m,取心总长度3791 m,取心层段主要为古近系塑脆性岩石。根据钻进特性,针对工区弹塑性层段和脆性层段提出了钻头选型原则。结合施工实践,经过多次试验、改进,在累计使用的硬质合金、复合片、巴拉斯3类15种钻头中,通过典型钻头结构型式、碎岩机理以及使用效果进行综合分析,优选出H-4-Ⅱ、F-3、F-6型3种钻头,在古近系地层取心钻进中效率高、取心质量好,适合工区地质条件,建议推广应用。  相似文献   

Design principle for parameters and interferences of tungsten carbide insert interface on roller bits     

YIN Kun  JONG Yonchol  BO Kun  CHOE Jongman 《世界地质(英文版)》2013,16(1):43-47

The lifetime of roll-bits with inserted tooth will be obviously decreased while drilling in strata and the tungsten carbide can be integrally separated from the roll-cone,which will need more trip out time to replace the roller bit.This study provides an entire analysis on stress as well as strength for teeth and tooth holes in loaded conditions.Qualities of tooth drop from matrix within roller bit.The optimized interferences of teeth inserted into the bit can be reasonably obtained by the critical interference derived from some relevant influence factors on the tooth-fixing quality of roller bits.  相似文献   

砂砾石大坝填筑碾压的相关试验与研究          下载免费PDF全文

张朋辉  韩赛超  李晓帅  张小东 《探矿工程》2017,44(5):72-77

针对南疆砂砾石填筑大坝进行碾压试验,验证坝体填筑设计压实标准的合理性、检验22 t自行式振动碾的适用性及其性能的可靠性。本试验主要采用室内相对密度试验、现场的碾压测定出碾压遍数、碾压沉降及相应密实度及其他试验参数,通过试验参数列表、试验参数包络线图与设计标准值的比较,得出最佳砂砾石填筑方案,同时也确定大坝填筑时的施工碾压控制参数,从而确保了工程质量。  相似文献   

Testing of dynamically substructured,base‐isolated systems using adaptive control techniques     

J. Y. Tu  P. Y. Lin  D. P. Stoten  G. Li 《地震工程与结构动力学》2010,39(6):661-681

Experimental techniques for testing dynamically substructured systems are currently receiving attention in a wide range of structural, aerospace and automotive engineering environments. Dynamic substructuring enables full‐size, critical components to be physically tested within a laboratory (as physical substructures), while the remaining parts are simulated in real‐time (as numerical substructures). High quality control is required to achieve synchronization of variables at the substructuring interfaces and to compensate for additional actuator system(s) dynamics, nonlinearities, uncertainties and time‐varying parameters within the physical substructures. This paper presents the substructuring approach and associated controller designs for performance testing of an aseismic, base‐isolation system, which is comprised of roller‐pendulum isolators and controllable, nonlinear magnetorheological dampers. Roller‐pendulum isolators are typically mounted between the protected structure and its foundation and have a fundamental period of oscillation far‐removed from the predominant periods of any earthquake. Such semi‐active damper systems can ensure safety and performance requirements, whereas the implementation of purely active systems can be problematic in this respect. A linear inverse dynamics compensation and an adaptive controller are tailored for the resulting nonlinear synchronization problem. Implementation results favourably compare the effectiveness of the adaptive substructuring method against a conventional shaking‐table technique. A 1.32% error resulted compared with the shaking‐table response. Ultimately, the accuracy of the substructuring method compared with the response of the shaking‐table is dependent upon the fidelity of the numerical substructure. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献