缝洞型油藏超大规模酸压技术     

杨敏  张烨 《地质科技情报》2011,30(3):89-92

塔河油田缝洞型油藏主要的储集体空间类型为溶蚀的裂缝及大型的溶洞,连通关系极其复杂,70％的钻井需要酸压才能投产.为进一步沟通远井地带的缝洞储集体,室内模拟及现场监测结果表明,超大规模酸压技术能够提高造缝长度,沟通井眼远处的储集体.通过多口井的研究及现场试验,在油气富集带上具有明显的地震反射异常,生产过程中供液不足的井进...  相似文献   

“Basin scale” versus “localized” pore pressure/stress coupling - Implications for trap integrity evaluation     

R. Mourgues  J.B. GressierL. Bodet  D. BureauA. Gay 《Marine and Petroleum Geology》2011,28(5):1111-1121

In petroleum industry, the difference between pore pressure (P_p) and minimum horizontal stress S_h (termed the seal or retention capacity) is of major consideration because it is often assumed to represent how close a system is to hydraulic failure and thus the maximum hydrocarbon column height that can be maintained. While S_h and P_p are often considered to be independent parameters, several studies in the last decade have demonstrated that S_h and P_p are in fact coupled. However, the nature of this coupling relationship remains poorly understood. In this paper, we explore the influences of the spatial pore pressure distribution on S_h/P_p coupling and then on failure pressure predictions and trap integrity evaluation. With analytical models, we predict the fluid pressure sustainable within a reservoir before failure of its overpressured shale cover. We verify our analytical predictions with experiments involving analogue materials and fluids. We show that hydraulic fracturing and seal breach occur for fluid pressure greater than it would be expected from conventional retention capacity. This can be explained by the impact of the fluid overpressure field in the overburden and the pressure diffusion around the reservoir on the principal stresses. We calculate that supralithostatic pressure could locally be reached in overpressured covers. We also define the retention capacity of a cover (RC) surrounding a fluid source or reservoir as the difference between the failure pressure and the fluid overpressure prevailing in shale at the same depth. In response to a localized fluid pressure rise, we show that the retention capacity does not only depend on the pore fluid overpressure of the overburden but also on the tensile strength of the cover, its Poisson’s ratio, and the depth and width of the fluid source.  相似文献   

华南早寒武世黑色岩系重晶石矿床环带钡冰长石 新发现及其意义   总被引：3，自引：0，他引：3  

韩善楚  胡凯  曹剑 《地质论评》2013,59(6):1143-1149

华南早寒武世黑色岩系重晶石矿床是全球著名的沉积型层状矿床。本文报道了我们最近的一项新发现,在该区天柱大河边重晶石矿床中首次发现了环带钡冰长石,环带的外带BaO含量1653%～1786%,K2O含量777%～819%,相比而言,核部BaO含量1204%～1421%,K2O含量860%～979%。结合成矿地质背景和已有工作报道,讨论了这一新发现的地质意义。认为这种环带钡冰长石的出现,反映了重晶石成矿受到热水作用影响,且其形成过程中经历了不同期富钡流体的影响,成矿可能属于一种热水、断控、幕式、渐进的过程,这不仅进一步揭示了矿床的热水（液）喷流沉积成因,而且加深了对成矿过程的刻画。该认识还可供全球沉积型重晶石矿床成因研究时类比参考。  相似文献   

The parnell quartz monzonite: A proterozoic zoned pluton in the archaean pilbara block,Western Australia     

W. J. Collins  C. M. Gray  A. D. T. Goode 《Australian Journal of Earth Sciences》2013,60(4):535-547

The Parnell Quartz Monzonite in the Pilbara Block of Western Australia is a Proterozoic (1731 ± 14 Ma) pluton characterized by high modal K‐feldspar and a greater abundance of hornblende relative to biotite, as is typical of Phanerozoic monzonitic rocks in eastern Australia. The only geochemical features reflecting its setting in an Archaean terrain are high Na2O, Ni and Cr. The pluton is zoned, with an increase in K‐feldspar, quartz and biotite and a decrease in plagioclase and hornblende from margin to core. Chemically, this zoning is reflected by systematic variation of CaO, K₂O, Na₂O, Sr and Rb, but ferromagnesian elements have irregular trends, implying preferential extraction of feldspars relative to mafic minerals during differentiation of the magma. The unusual geochemical trends are explained by a model involving ‘in situ’ feldspar fractionation of a K‐rich residual liquid from a mafic crystalline mush.

A parent magma similar to the average rock composition of the pluton is deduced because high ferromagnesian trace element abundances preclude extensive fractionation of mafic minerals. Geochemical and isotopic constraints suggest that the ultimate source was chemically similar to a shoshonitic basaltic andesite, that must have been emplaced beneath the eastern margin of the Pilbara Block in the Early Proterozoic. Subsequent partial melting of this postulated underplated source at ～ 1700 Ma to produce the Parnell Quartz Monzonite was probably associated with tectonism in the Gregory Range Complex.  相似文献   

保德区块中低阶煤层压裂施工砂堵原因分析及技术对策          下载免费PDF全文

师伟  李孟  樊洪波 《探矿工程》2016,43(12):12-17

针对保德区块中低阶煤储层压裂过程中容易出现砂堵影响储层改造效果的问题,根据研究区块的地质条件,结合水力压裂时裂缝在煤层中的扩展规律,分析了保德区块煤层水力压裂出现砂堵的4类主要原因,分别为煤储层裂隙相对发育造成压裂液滤失量增加、压裂沟通高渗透性的顶底板、煤储层本身有效厚度大滤失量增大及多层合压造缝不充分。在此基础上,提出了相应的技术对策,使用清洁压裂液、适当提高并稳定施工排量及优化压裂施工设计,为现场的水力压裂施工和提高煤储层改造效果提供重要指导。  相似文献   

不同压裂介质影响下绝对应力测值的试验研究     

周龙寿  丁立丰  郭啟良 《岩土力学》2013,34(10):2869-2876

为研究不同压裂介质影响下的绝对应力测值,利用大尺寸真三轴模拟水压致裂试验系统,用清水及密度分别为1.1、1.2、1.3、1.4 g/cm3的泥浆介质对400 mm×400 mm×400 mm的花岗岩试样进行了水压致裂室内试验,成功获取了连续的压力-时间曲线。利用6种方法识别压力-时间曲线的闭合压力点,与实加最小水平主应力（ 5 MPa）对比,得出单切线等4种方法较为符合实际情况;在考虑试验系统柔度影响前提下,对比了实测和理论重张压力;最后分析了在持续泵压作用下岩石裂缝延伸的压力。试验结果表明,密度为1.1、1.2 g/cm3的泥浆介质对压力特征参数的取值影响较小,误差不超过1 MPa,但密度为1.3、1.4 g/cm3的泥浆介质对特征参数值影响很大。试验结果对水压致裂地应力测量技术在不同压裂介质影响下的适用性有重要的指导意义。  相似文献   

山西煤矿矿区井下地应力场分布特征研究   总被引：19，自引：2，他引：17       下载免费PDF全文

康红普  林健  颜立新  张晓  吴拥政  司林坡 《地球物理学报》2009,52(7):1782-1792

采用煤矿井下专用的小孔径水压致裂地应力测量装置,在山西省的晋城、潞安、汾西、华晋、阳泉、平朔、大同等矿区,完成了160个测点的地应力测量,测点地质条件涵盖了山西省煤矿大部分条件.基于实测数据,分析了地应力与测点埋深的关系,不同深度条件下煤矿矿区井下地应力状态;绘制出山西省煤矿矿区井下地应力分布图,并与震源机制解的分析结果进行了比较,得出山西省煤矿矿区井下地应力场分布特征与变化规律.煤矿井下水平应力总体上随着埋深增加而增大,但由于各矿区地质条件差异较大,导致地应力测试数据离散性也较大;埋深小于250 m的岩层应力状态主要为σ_H>σ_h>σ_V型,埋深处于250~500 m的岩层应力状态以σ_H>σ_V>σ_h型为主,埋深较大的矿区主要为σ_V>σ_H>σ_h型;最大水平主应力与垂直主应力的比值绝大部分集中在0.5~2.0之间,而且随着埋深增加,侧压比呈现减小的趋势,并向1附近集中;最大水平主应力与最小水平主应力的比值主要集中在1.5～2.0之间;平均水平主应力与垂直主应力的比值大多处于0.5～1.5,尤以0.5～1.0之间最多;山西省煤矿矿区从北到南,最大水平主应力方向发生了较大变化.北部最大水平主应力方向为NE,往南发生偏转到NNW;靠东部与西部偏向NW;靠东南部出现了多变的方向.井下实测数据与震源机制解相比在部分区域一致性较好,而在另一些区域存在明显的差异.特别是在受较大地质构造影响的区域,水平主应力方向往往发生明显的扭转和变化.  相似文献   

Numerical Simulation Study on the Effect of Horizontal Well Reservoir Stimulation for Gas Hydrate Production     

LI Xiaoyang  TIAN Yingying  ZHANG Xin  SONG Gang  ZHAO Ming  LIANG Jinqiang  HUANG Wei  MENG Fanle 《《地质学报》英文版》2022,96(2):701-712

A new gas hydrate reservoir stimulation method of in-situ fracturing with transient heating is proposed, in line with analysis of the technological bottlenecks faced by marine gas hydrate production. This method injects the developed chemical reagents into a hydrate reservoir through hydraulic fracturing, releasing heat during the chemical reaction to increase the hydrate decomposition rate. The chemical reaction product furthermore has a honeycomb structure to support fractures and increase reservoir permeability. Based on the geological model of natural gas hydrate in the South China Sea, three development methods are simulated to evaluate hydrate production capacity, consisting of horizontal well, fractured horizontal well and in-situ fracturing with transient heating well. Compared with the horizontal well, the simulation results show that the cumulative gas production of the fractured horizontal well in one year is 7 times that of the horizontal well, while the cumulative gas production of in-situ fracturing with transient heating well is 12 times that of the horizontal well, which significantly improves daily efficiency and cumulative gas production. In addition, the variation patterns of hydrate saturation and temperature-pressure fields with production time for the three exploitation plans are presented, it being found that three sensitive parameters of fracture conductivity, fracture half-length and fracture number are positively correlated with hydrate production enhancement. Through the simulations, basic data and theoretical support for the optimization of gas hydrate reservoir stimulation scheme has been provided.  相似文献   

Periodical mixing of MORB magmas near East Pacific Rise 13°N: Evidence from modeling and zoned plagioclase phenocrysts     

GuoLiang Zhang  ZhiGang Zeng  XueBo Yin  DaiGeng Chen  XiaoYuan Wang  XiaoMei Wang 《中国科学D辑(英文版)》2008,51(12):1786-1801

Thirty-six basalt samples from near East Pacific Rise 13°N are analyzed for major and trace elements. Different types of zoned plagioclase phenocrysts in basalts are also backscatter imaged, and major element profiles scanned and analyzed for microprobe. Basalts dredged from a restricted area have evolved to different extents (MgO=9.38wt%—6.76wt%). High MgO basalts are modeled for crystalliza-tion to MgO of about 7wt%, and resulted in the Ni contents (≈28 ppm) that are generally lower than that in observed basalts (>60 ppm). It suggests that low MgO basalts may have experienced more intensive magma mixing. High MgO (9.38wt%) basalt is modeled for self-"mixing-crystallization", and the high Ni contents in low MgO basalts can be generated in small scale and periodical self-mixing of new magma (high MgO). "Mixing-crystallization" processes that low MgO magmas experienced accord with recent 226Ra/230Th disequilibria studies for magma residence time, in which low MgO magmas have experi-enced more circles of "mixing-crystallization" in relatively longer residence time. Magma mixing is not homogeneous in magma chamber, however, low MgO magmas are closer to stable composition pro-duced by periodical "mixing-crystallization", which is also an important reason for magma diversity in East Pacific Rise. Zoned plagioclase phenocrysts can be divided into two types: with and without high An# cores, both of which have multiple reversed An# zones, suggesting periodical mixing of their host magmas. Cores of zoned plagioclase in low MgO (7.45wt%) basalt differ significantly with their mantle in An#, but are similar in An# with microlite cores (products of equilibrium crystallization) in high MgO (9.38wt%) basalt, which further shows that plagioclase phenocryst cores in low MgO basalts may have formed in their parental magmas before entering into the magma chamber.  相似文献   

自然营造力作用下岩体混凝土水力劈裂分析与探讨   总被引：4，自引：2，他引：2  

李宗利  任青文 《岩土力学》2008,29(8):2121-2125

水利水电、矿业等工程在自然营造力作用下的水力劈裂边界条件与人工致裂不完全相同,有其自身的特点。在总结自然营造力作用下水力劈裂特点的基础上,根据研究的尺度不同,将水力劈裂研究分为岩体宏观的、综合的、统计意义上的水力劈裂和单裂纹的水力劈裂研究两种。分析了单裂纹内水流特性,将单裂纹内的水力劈裂分为两个阶段（或两种情况）分别进行研究,并将此问题得以简化,同时还提出了不同阶段裂纹内水流运动分析的模型。  相似文献