长春硬塑状态老黏性土地基承载力     

孙广利  李广杰  周景宏  于光源 《吉林大学学报(地球科学版)》2014,44(2):591-595

为提供长春硬塑状态老黏性土可靠的地基承载力依据,探讨适宜的确定地基承载力的方法,采用载荷试验、静力触探试验原位测试和室内土工试验等方法对长春老黏性土进行了测试研究,获取了地基承载力特征值（306~425 kPa）、静力触探锥尖阻力（1.9~3.3 MPa）、天然孔隙比(0.63~0.72)和液性指数(0.02~0.25)等试验数据。通过对试验数据的统计分析,得出地基承载力特征值与静力触探锥尖阻力线性相关,并与天然孔隙比和液性指数线性相关的结论。据此,提出了根据静力触探锥尖阻力计算长春老黏性土地基承载力特征值的经验公式,总结出根据室内土工试验指标确定长春老黏性土地基承载力特征值的数据表。  相似文献   

利用GPS掩星弯曲角确定对流层顶高度     

高攀  徐晓华  张小红  吕翠仙 《武汉大学学报(信息科学版)》2012,37(12):1417-1420

利用COSMIC提供的GPS无线电掩星观测数据,从掩星弯曲角廓线出发确定对流层顶高度,并分别与对应的掩星温度廓线确定的温度最低点对流层顶(cold point tropopause,CPT)和温度递减率对流层顶(lapse rate tropopause,LRT)、无线电探空(距离掩星事件300km以内、观测时间差异3h以内)温度廓线确定的CPT和LRT进行了对比。  相似文献   

Piles shaft capacity from CPT and CPTu data by polynomial neural networks and genetic algorithms     

H. Ardalan  A. Eslami  N. Nariman-Zadeh 《Computers and Geotechnics》2009

Cone penetration test (CPT) is one of the most common in situ tests which is used for pile design because it can be realized as a model pile. The measured cone resistance (q_c) and sleeve friction (f_s) usually are employed for estimation of pile unit toe and shaft resistances, respectively. Thirty three pile case histories have been compiled including static loading tests performed in uplift, or in push with separation of shaft and toe resistances at sites which comprise CPT or CPTu sounding. Group method of data handling (GMDH) type neural networks optimized using genetic algorithms (GAs) are used to model the effects of effective cone point resistance (q_E) and cone sleeve friction (f_s) as input parameters on pile unit shaft resistance, applying some experimentally obtained training and test data. Sensitivity analysis of the obtained model has been carried out to study the influence of input parameters on model output. Some graphs have been derived from sensitivity analysis to estimate pile unit shaft resistance based on q_E and f_s. The performance of the proposed method has been compared with the other CPT and CPTu direct methods and referenced to measured piles shaft capacity. The results demonstrate that appreciable improvement in prediction of pile shaft capacity has been achieved.  相似文献   

Load-settlement behavior modeling of single piles using artificial neural networks and CPT data     

《Computers and Geotechnics》2017

Pile foundations are usually used when the conditions of the upper soil layers are weak and unable to support the super-structural loads. Piles carry these super-structural loads deep into the ground. Therefore, the safety and stability of pile-supported structures depends largely on the behavior of the piles. In addition, accurate prediction of pile behavior is necessary to ensure appropriate structural and serviceability performance. In this paper, an ANN model is developed for predicting pile behavior based on the results of cone penetration test (CPT) data. Approximately 500 data sets, obtained from the published literature, are used to develop the ANN model. The paper compares the predictions obtained by the ANN with those given by a number of traditional methods and it is observed that the ANN model significantly outperforms the traditional methods. An important advantage of the ANN model is that the complete load-settlement relationship is captured. Finally, the paper proposes a series of charts for predicting pile behavior that will be useful for pile design.  相似文献   

Bayesian approach for calibrating transformation model from spatially varied CPT data to regular geotechnical parameter     

《Computers and Geotechnics》2017

Cone Penetration Test (CPT) is widely utilized to gain regular geotechnical parameters such as compression modulus, cohesion coefficient and internal friction angle by transformation model in the site investigation. However, it is challenging to obtain simultaneously the unknown coefficients and error of a transformation model, given the intrinsic uncertainty (i.e., spatial variability) of geomaterial and the epistemic uncertainty of geotechnical investigation. A Bayesian approach is therefore proposed calibrating the transformation model based on spatial random field theory. The approach consists of three key elements: (1) three-dimensional anisotropic spatial random field theory; (2) classifications of measurement and error, and the uncertainty propagation diagram of geotechnical investigation; and (3) the unknown coefficients and error calibration of the transformation model given Bayesian inverse modeling method. The massive penetration resistance data from CPT, which is denoted as a spatial random field variable to account for the spatial variability of soil, are classified as type A data. Meanwhile, a few laboratory test data such as the compression modulus are defined as type B data. Based on the above two types of data, the unknown coefficients and error of the transformation model are inversely calibrated with consideration of intrinsic uncertainty of geomaterial, epistemic uncertainties such as measurement errors, prior knowledge uncertainty of transformation model itself, and computing uncertainties of statistical parameters as well as Bayesian method. Baseline studying indicates the proposed approach is applicable to calibrate the transformation model between CPT data and regular geotechnical parameter within spatial random field theory. Next, the calibrated transformation model was compared with classical linear regression in cross-validation, and then it was implemented at three-dimensional site characterization of the background project.  相似文献   

由CPT确定灌注桩极限承载力的可靠性分析   总被引：1，自引：1，他引：0  

赵春风  叶观宝  李建新  高大钊 《岩土力学》1999,20(1):65-68

利用随机场理论,研究了灌注桩的Ｐｓ,ｆｉ和Ｐｓｂ统计特性的统计原则,对相关距离、桩截面尺寸、端阻力计算范围等在程序编制中的协调问题进行了探讨;对上海地区１７个场地的４６条ＣＰＴ曲线进行了电算,进而求出了由ＣＰＴ确定灌注桩极限承载力的可靠度指标的统计特性。  相似文献   

海上静力触探(CPT)测试技术的发展现状和应用     

陆凤慈  曲延大  廖明辉 《海洋技术学报》2004,23(4):32-36

静力触探(CPT)是一种速度快,数据连续、再现性好、操作省力等优点的原位测试方法。随着海洋开发的迅速发展,CPT测试技术在国内外海洋工程领域的使用越来越普遍。因此,了解国外海上CPT设备和应用情况,探讨应用中的问题,对CPT测试技术在我国海上工程领域的应用具有重要意义。文章描述了国外海上静力触探(CPT)测试技术的发展现状,阐明了主要的海床CPT(Seabed CPT)设备和井下CPT(Downhole CPT)设备的特点,并对不同CPT设备在海洋工程领域的应用作了分析,这对海上CPT测试技术在我国的应用和发展具有一定的参考价值和指导作用。  相似文献   

饱和黄土场地原位试验及液化势评价     

董林  严武建  夏坤  李少华  刘琨 《震灾防御技术》2018,13(4):950-958

目前,主要依靠室内动力试验对黄土液化势进行评价。由于黄土特殊的结构性,室内试验对其饱和的过程较为复杂,且与实际场地饱和黄土差异明显,导致室内黄土液化试验结果并不能代表现场饱和黄土的抗液化强度。本文选取兰州市西固区寺儿沟村某饱和黄土场地进行钻孔测试,现场实施了标准贯入试验、静力触探试验以及剪切波速测试。应用Robertson的土类指数分类图对该场地不同含水率黄土的土类进行了界定,确定了饱和黄土属于类砂土,有液化势。应用NCEER推荐方法,计算了3组原位试验数据的饱和黄土循环抗力比（CRR）,通过与1976年唐山地震和1999年集集地震液化土CRR对比,得出了饱和黄土抗液化强度很低的结论。  相似文献   

The cone penetration test and 2D imaging resistivity as tools to simulate the distribution of hydrocarbons in soil     

《Physics and Chemistry of the Earth》2016

The purpose of geophysical electrical surveys is to determine the subsurface resistivity distribution by making measurements on the ground surface. From these measurements, the true resistivity of the subsurface can be estimated. The ground resistivity is related to various geological parameters, such as the mineral and fluid content, porosity and degree of water saturation in the rock. Electrical resistivity surveys have been used for many decades in hydrogeological, mining and geotechnical investigations. More recently, they have been used for environmental surveys. To obtain a more accurate subsurface model than is possible with a simple 1-D model, a more complex model must be used. In a 2-D model, the resistivity values are allowed to vary in one horizontal direction (usually referred to as the x direction) but are assumed to be constant in the other horizontal (the y) direction. A more realistic model would be a fully 3-D model where the resistivity values are allowed to change in all three directions. In this research, a simulation of the cone penetration test and 2D imaging resistivity are used as tools to simulate the distribution of hydrocarbons in soil.  相似文献   

CPT-based analysis of liquefaction and re-liquefaction following the Canterbury earthquake sequence     

《Soil Dynamics and Earthquake Engineering》2015

The Canterbury region experienced widespread damage due to liquefaction induced by seismic shaking during the 4 September 2010 earthquake and the large aftershocks that followed, notably those that occurred on 22 February, 13 June and 23 December 2011. Following the 2010 earthquake, the Earthquake Commission directed a thorough investigation of the ground profile in Christchurch, and to date, more than 7500 cone penetration tests (CPT) have been performed in the region. This paper presents the results of analyses which use a subset of the geotechnical database to evaluate the liquefaction process as well as the re-liquefaction that occurred following some of the major events in Christchurch. First, the applicability of existing CPT-based methods for evaluating liquefaction potential of Christchurch soils was investigated using three methods currently available. Next, the results of liquefaction potential evaluation were compared with the severity of observed damage, categorised in terms of the land damage grade developed from Tonkin & Taylor property inspections as well as from observed severity of liquefaction from aerial photography. For this purpose, the Liquefaction Potential Index (LPI) was used to represent the damage potential at each site. In addition, a comparison of the CPT-based strength profiles obtained before each of the major aftershocks was performed. The results suggest that the analysis of spatial and temporal variations of strength profiles gives a clear indication of the resulting liquefaction and re-liquefaction observed in Christchurch. The comparison of a limited number of CPT strength profiles before and after the earthquakes seems to indicate that no noticeable strengthening has occurred in Christchurch, making the area vulnerable to liquefaction induced land damage in future large-scale earthquakes.  相似文献