沟岸侧蚀对泥石流不稳定动力过程的影响          下载免费PDF全文

吕立群  王兆印  崔鹏  徐梦珍 《水科学进展》2018,29(2):213-220

泥石流作为非牛顿体,屈服应力大,运动过程通常不稳定。前人建立了许多模型来研究沟床揭底和堰塞体溃决对泥石流不稳定动力过程的影响,沟岸侧蚀对泥石流不稳定动力过程的影响研究较少。通过侧蚀为主的模型和完全底蚀的模型两种水槽实验的对比,针对泥石流的动力过程展开研究。实验发现两种工况条件下泥石流正应力和孔隙水压力随着龙头高度沿程波动性的增长而相应地波动性增大,但侧蚀作用使得这种波动特征更加明显。通过力学分析,证明侧蚀作用导致泥石流龙头的阻力更大,但是龙身颗粒和龙头颗粒的速度差更大,使得龙头附加坡降更大,因此,侧蚀作用使得泥石流龙头的平均速度更快。泥石流龙头浓度和容重的不断增大,使得阻力不断增大,阻力和动力的动态平衡关系是泥石流不稳定运动的原因之一。  相似文献   

冻土机械切削破碎机理的研究进展   总被引：1，自引：1，他引：0  

李龙  周琴  张凯  凌雪  张在兴  李耀 《冰川冻土》2021,43(2):638-649

冻土开挖困难、破碎效率低是高寒地区工程建设、地基施工等面临的技术难题。冻土机械切削破碎是冻土开挖的主要方法,其机理研究是提高冻土破碎效率的前提和基础。首先总结了温度、含水率、围压等对冻土复杂力学特性的影响,进而调研分析了冻土机械切削破碎的典型切削力学模型,发现冻土切削机械破碎模式不仅与冻土力学特性密切相关,也与切削参数和刀具结构直接相关,冻土切削过程中存在着最优的切削前角（30°~60°）,且深切削和浅切削时冻土内部受力方式存在差异也会导致破坏形式的不同;温度、含水率、围压所造成的冻土力学性能变化会直接导致冻土破坏过程和切削破碎机理的改变,冻土强度随着温度降低表现出先升高然后保持稳定的特性,随着含水率升高呈现出先升高后降低的趋势,冻土破碎存在脆性、塑脆过渡及塑性等不同破坏形式。通过系统总结冻土切削破碎机理研究进展,进一步明确了冻土力学性质主要影响因素、变化特点及其切削破坏损伤特征,为冻土机械切削破碎的切削参数和切削具结构优化提供了设计依据。  相似文献   

六种成膜封堵剂的室内实验优选与评价          下载免费PDF全文

王建伟 《探矿工程》2021,48(3):73-77

为更好地服务深部钻探工程,准确了解冲洗液封堵性能,对6种成膜封堵剂开展了砂床实验、API静失水量实验、流变性能实验及抗温实验等室内实验进行优选与评价。实验结果表明,2号和4号成膜封堵剂在6种成膜封堵剂中封堵性能最好,它们在基浆中的最优加量均为2%,100 ℃温度条件下加入这2种封堵剂的冲洗液具有较好的抗温性能;冲洗液中膨润土含量和处理剂是影响冲洗液封堵性能的2个重要因素：膨润土含量越高,冲洗液封堵性能越好,加入聚合物、降滤失剂等处理剂可以提高冲洗液的封堵性能。砂床实验是评价冲洗液封堵性能好坏的重要依据。  相似文献   

成层软土地基预固结处理后桩基水平承载力估算方法     

黄朝煊  袁文喜  胡国杰 《岩土力学》2021,(1):113-124,134

目前通过对软土地基预加固处理来提高桩基水平承载力已被工程界认可,但如何在工程前期设计过程中估算软土地基预处理后桩基水平承载力提高值仍是技术难点。基于此,参考Bowles[1]的地基土水平抗力计算式,同时考虑成层软土地基预排水固结处理影响,通过数学推导,推求出根据原状软土室内土工试验抗剪强度指标及预加固处理时间,估算软土地基预处理后桩基水平承载力提高值的实用计算方法。考虑桩侧土弹塑性屈服影响,推导出成层软土中水平受荷桩弹塑性解析解及塑性区深度的计算式,给出了桩顶水平位移、桩身最大弯矩的无量纲计算式及相关计算源代码。依托于浙江省某水闸桩基工程案例,根据提出的计算方法对桩基水平承载力、桩顶水平位移及桩身最大弯矩等性状进行预估计算,并与地基预处理前、后现场试桩检测值进行验证对比,认为桩基水平承载力、桩顶水平位移及桩身最大弯矩等预估计算成果与工程现场试桩的检测值较接近,对类似工程设计具有较好的参考价值。  相似文献   

井筒电加热改善水平井蒸汽吞吐效果机理实验     

吴永彬  吕柏林  杜宣  卢迎波  蒋有伟  邢向荣 《现代地质》2021,35(4):1136-1146

针对稠油水平井蒸汽吞吐面临入井渗流阻力大、产量水平低、吞吐递减率高、采收率偏低等问题,提出了电加热辅助水平井蒸汽吞吐方法。首先根据水平井蒸汽吞吐过程中的电加热与蒸汽复合传热特征,建立了电加热辅助蒸汽吞吐三个阶段的(注汽阶段、焖井阶段、生产阶段)储层升温解析模型,在此基础上,设计并开展了电加热辅助蒸汽吞吐和常规水平井吞吐的宏观比例物理模拟对比实验,通过实验验证了解析公式,揭示电加热改善水平井吞吐效果关键机理,并利用实际典型井模型进行了潜力预测。结果表明:电加热协同蒸汽吞吐,具有注蒸汽阶段实现水平段均匀加热升温、焖井阶段持续热补偿加热近井地带、生产阶段降低原油入井渗流阻力并提高吞吐产量的关键机理。典型井组预测电加热辅助水平井吞吐可提高吞吐采收率9.4%,油汽比从0.14提高到0.23,在水平井蒸汽吞吐油藏具有重要应用潜力。  相似文献   

Nonlinear analysis of laterally loaded rigid piles in cohesive soil     

Lianyang Zhang  Saeed Ahmari 《国际地质力学数值与分析法杂志》2013,37(2):201-220

This article presents a method for the nonlinear analysis of laterally loaded rigid piles in cohesive soil. The method considers the force and the moment equilibrium to derive the system equations for a rigid pile under a lateral eccentric load. The system equations are then solved using an iteration scheme to obtain the response of the pile. The method considers the nonlinear variation of the ultimate lateral soil resistance with depth and uses a new closed‐form expression proposed in this article to determine the lateral bearing factor. The method also considers the horizontal shear resistance at the pile base, and a bilinear relationship between the shear resistance and the displacement is used. For simplicity, the modulus of horizontal subgrade reaction is assumed to be constant with depth, which is applicable to piles in overconsolidated clay. The nonlinearity of the modulus of horizontal subgrade reaction with pile displacement at ground surface is also considered. The validity of the developed method is demonstrated by comparing its results with those of 3D finite element analysis. The applications of the developed method to analyze five field test piles also show good agreement between the predictions and the experimental results. The developed method offers an alternative approach for simple and effective analysis of laterally loaded rigid piles in cohesive soil. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

Estimating the crush zone size under a cutting tool in coal     

R. K. Zipf Jr.  Z. T. Bieniawski 《Geotechnical and Geological Engineering》1988,6(4):279-295

Summary As part of an effort to understand the mechanics of fine fragment formation in coal, which is important in studies of respirable dust due to mining, fracture toughness measurements and the strain energy density (SED) theory were applied to calculate the crush zone size under a cutting tool in coal. This zone is the major source of fine fragments in the 1 to 10 µm size range. The model used in these calculations is a boundary element program containing a failure criterion based on the SED theory. The boundary element program calculates linear elastic stresses at numerous points in the coal material ahead of a cutting bit. These stresses are then input to a subroutine called critical flaw length and orientation (CFLO) which uses the SED theory to determine the CFLO for a small crack at the boundary element stress computation point. The extent of crushing is based on earlier postulates about the role of inherent flaws in a fragmentation process. To form 1 to 10 µm fragments requires firstly a local stress strong enough to activate flaws with a characteristic length less than 1 to 10 µm and secondly, a flaw density sufficient to provide an average spacing between flaws also on the order of 1 to 10 µm. The locus of active 10 µm flaws represents the maximum possible extent of fine fragmentation in the 10 µm or less size range assuming that a sufficient inherent flaw density exists. The approach offers a first order approximation to the extent of crushing under a tool tip. The size and shape of the crush zone volume is affected by the attack angle and geometry of the tool.  相似文献   

A simple criterion for the machinability of hard rocks     

S. P. Singh 《Geotechnical and Geological Engineering》1989,7(3):257-266

Conclusions The application of mechanical methods for rapid excavation requires more detailed and precise knowledge of the site, but there is no single parameter which can provide a comprehensive measure for the selection and performance of a tunnel boring machine.The machinability index proposed in this paper is based on four different parameters which influence the performance of a tunnelling machine and are widely accepted by the engineers and geologists. In order to develop a comprehensive measure regarding the borability of rocks,in situ conditions must be evaluated. The machinability index coupled with thein situ information would facilitate judicious decisions regarding the application and selection of tunnel boring machines.The geological conditions and rock characteristics cannot be controlled but their knowledge can prevent costly mistakes in equipment selection and assist in identifying alternative excavation systems, therefore a thorough site investigation can substantially reduce the economic and technical risks associated with tunnelling and mine development.  相似文献   

输水管网模糊地震可靠性的 Monte Carlo 法分析程序     

刘锡荟  王海燕  张锐 《地震研究》1989,(3)

本文详细介绍了笔者所建议的运用模糊图理论和方法进行城市输水管网的地震可靠性分析途径和计算程序。对于输水管网中每段管道的震害预测,建立了相应的专家系统。在此基础上,定义了管网系统的模糊可靠性,更好地反映了人们对于管道损坏状态估计的模糊性和对可靠性要求上的模糊性。以模糊矩阵来描述输水管网的状态是十分方便的。通过计算模糊矩阵的传递闭包,极易找出最短路、关键段等。由于地震作用和管道抗震能力都是随机的,因此整个管网系统的可靠性分析是藉助Monle Carlo法进行的。以Monle Carlo法对模糊图进行分析,从而得到管网的地震可靠性,这还是首次。用PASCAL和PROLOG编制了在微机上实用的计算机程序,特别是以智能语言PROLOG编制的程序,更有许多特色。由于采用了一些技巧,使在微机上可以分析相当大的系统,为城市抗震防灾工作提供了一个有力的工具。  相似文献   

Shear resistance of jointed rock masses and stability calculation of rock slopes     

Xing Zhang 《Geotechnical and Geological Engineering》1993,11(2):107-124

Summary Based on an extension to a model originally proposed by Zhang (1990), a method for estimating the shear strength of a jointed rock mass containing two joint sets is developed. Compared to the original method in which only a single en-echelon joint set was considered, the new method has the following advantages: (1) it allows a much more realistic joint pattern to be incorporated; (2) the effects of joint connectivity and intersection angle between joint sets on shear strength are included. Use of the new method is demonstrated by application to the calculation of the stability of slopes in jointed rock. The importance of joint connectivity, joint persistence and joint set intersection angle on slope stability, as predicted by the model, is revealed.  相似文献