一维综合孔径微波辐射计遥感海面温度的敏感性分析     

陈冠宇  艾未华  陆文  冯梦延 《海洋学报》2019,41(3):143-154

一维综合孔径微波辐射计能够有效提高观测的空间分辨率，其观测入射角通常在0°~55°范围内变化。为了开发适用于一维综合孔径微波辐射计的海面温度反演算法，需要评估其观测亮温对海洋大气环境要素的敏感性。利用海面发射率模型和大气辐射传输模型，构建了适用于一维综合孔径微波辐射计的微波海洋大气辐射传输模式，研究了C波段垂直和水平极化微波辐射亮温在不同入射角下对海洋大气环境要素的敏感性变化情况，并定量计算了相应的敏感系数。结果表明:垂直和水平极化亮温对海洋大气环境要素的敏感性表现出不同的特性。随着入射角的增大，垂直极化亮温对海面温度的敏感性增强，对海面风场的敏感性相对减弱；水平极化亮温则相反。由大气水汽含量和云液态水含量误差引入的垂直和水平极化亮温误差随入射角增大而增大，但是，即使在55°的大入射角下垂直和水平极化亮温误差仍小于0.12 K。对于海面温度反演精度优于1 K的要求，一维综合孔径微波辐射计的测温精度需优于0.6 K。研究结果对于一维综合孔径微波辐射计海面温度反演算法的研究和载荷设计具有一定的理论指导意义。  相似文献   

基于星载红外辐射计的北极海表温度数据对比分析     

张精英  孙伟富  张杰  孟俊敏  马毅 《海洋科学》2018,42(11):1-12

本文基于2016年MODIS(ModerateResolutionImagingSpectroradiometer)-Aqua、MODIS-Terra和VIIRS(Visible Infrared Imager Radiometer Suite)三种红外辐射计的海表面温度(Sea Surface Temperature,SST)数据,统计了北极地区红外SST1月和7月的覆盖率及有效覆盖天数,并与Argo(Arrayfor Real-timeGeostrophicOceanography)浮标数据进行了匹配验证,直观获取北极SST误差分布情况并研究SST遥感观测能力,为更好地了解北极地区从而应对气候变化提供一定的资料基础。结果表明,北极地区红外辐射计SST数据7月的覆盖率和有效观测天数均高于1月,1月三种数据相差不大,7月VIIRS的覆盖率和有效观测天数均优于MODIS-Aqua和MODIS-Terra,联合三种红外辐射计的覆盖率和有效观测天数相较于单星有所增加, 1月覆盖率最高为8%, 7月最高接近70%,表明多星联合探测是提高北极地区SST数据覆盖率和观测天数的有效方法;北极地区SST数据的误差普遍高于全球总体水平, VIIRS白天、夜间的均方根误差(E_(rms))均低于MODIS-Aqua和MODIS-Terra, MODIS-Aqua白天SST的E_(rms)高于MODIS-Terra,夜间则低于MODIS-Terra。综合来看, VIIRS在北极的覆盖率、有效观测天数及与浮标的匹配结果在三种红外辐射计中为最优。  相似文献   

强震临震微波动现象初步研究(二)   总被引：1，自引：0，他引：1  

杨立明  郝臻  王建军  张淑珍  姚家俊  董蕾 《中国地震》2018,34(2):234-243

为了验证和检验强震临震微波动现象及其主要特征,利用甘、青、川、滇、藏等区域台网200余个宽频带数字地震台站的波形资料,建立了实时监控技术系统。通过对2012~2014年间青藏块体发生的24次5级以上地震及部分无震区域台站观测的全程实时跟踪、动态监控,检验和验证了临震微波动现象的重现性和客观性,验证了临震微波动现象的频谱、时间、空间、方向性等特征,进一步得出了临震微波动现象可能与地震强度有关,且震级越大,震前出现持续临震微波动的可能性越大的结论。  相似文献   

设计反应谱标定方法的研究现状与讨论          下载免费PDF全文

蒋晓涵  薄景山    王竞  韩昕  郭晓云  赵培培  谭启迪 《世界地震工程》2018,34(4):038-48

设计反应谱及其标定方法的研究是工程抗震研究领域的基本问题之一。在现有研究成果的基础上，归纳和总结了设计反应谱及其标定方法的研究历史和现状；评述了研究进程中的若干节点问题；介绍了设计反应谱的标定原理和当前几种有代表性的设计反应谱的标定方法；分析了设计反应谱标定参数的影响因素。在此基础上，对设计反应谱及其标定方法研究中的强震资料积累问题、谱形状问题、标定参数的确定问题以及标定方法等问题进行了讨论并提出了改进和进一步研究的建议。  相似文献   

基于一维综合孔径微波辐射计的海面温度反演研究   总被引：1，自引：0，他引：1  

艾未华  冯梦延  陈冠宇  陆文 《海洋学报(英文版)》2020,42(5):115-122

Due to the low spatial resolution of sea surface temperature(T_S) retrieval by real aperture microwave radiometers,in this study, an iterative retrieval method that minimizes the differences between brightness temperature(T_B)measured and modeled was used to retrieve sea surface temperature with a one-dimensional synthetic aperture microwave radiometer, temporarily named 1 D-SAMR. Regarding the configuration of the radiometer, an angular resolution of 0.43° was reached by theoretical calculation. Experiments on sea surface temperature retrieval were carried out with ideal parameters; the results show that the main factors affecting the retrieval accuracy of sea surface temperature are the accuracy of radiometer calibration and the precision of auxiliary geophysical parameters. In the case of no auxiliary parameter errors, the greatest error in retrieved sea surface temperature is obtained at low T_S scene(i.e., 0.710 6 K for the incidence angle of 35° under the radiometer calibration accuracy of0.5 K). While errors on auxiliary parameters are assumed to follow a Gaussian distribution, the greatest error on retrieved sea surface temperature was 1.330 5 K at an incidence angle of 65° in poorly known sea surface wind speed(W)(the error on W of 1.0 m/s) over high W scene, for the radiometer calibration accuracy of 0.5 K.  相似文献   

Global Statistical Assessment and Cross-Calibration with Jason-2 for Reprocessed HY-2 A Altimeter Data     

Maofei Jiang  Ke Xu  Yalong Liu 《Marine Geodesy》2018,41(3):289-312

HY-2 A (Haiyang-2 A) satellite was launched on August 16, 2011 and radar altimeter is one of its main payloads. We reprocessed two years of HY-2 A altimeter sensor geophysical dataset records (SGDR) data. This paper presents the main results in terms of reprocessed HY-2 A altimeter data quality: verification of data availability and validity, monitoring several relevant altimeter parameters, and assessment of the HY-2 A altimeter system performances. A cross-calibration analysis of reprocessed HY-2 A altimeter data with Jason-2 was conducted. The reprocessed HY-2 A altimeter data show good quality and have a low level of noise with respect to Jason-2. The same geophysical correction methods were used to calculate the sea surface height (SSH) for the two missions. The mean standard deviations of the crossover differences for HY-2 A and Jason-2 are 5.24 cm and 5.34 cm, respectively. The mean standard deviation of the crossover differences between HY-2 A and Jason-2 is 5.37 cm. These show that HY-2 A can provide SSH measurements at almost the same level of accuracy as Jason-2. The relative SSH bias between HY-2 A and Jason-2 due to the Ultra Stable Oscillator (USO) drift is obviously observed, and it can affect the calculation of mean sea level and should be further studied and corrected.  相似文献   

Calibration method affects the measured δ2H and δ18O in soil water by direct H2Oliquid–H2Ovapour equilibration with laser spectroscopy     

Hongxiu Wang  Bingcheng Si  Dyan Pratt  Han Li  Xiaojun Ma 《水文研究》2020,34(2):506-516

The direct H₂O_liquid–H₂O_vapour equilibration method utilizing laser spectroscopy (DVE-LS) is a way to measure soil pore water stable isotopes. Various equilibration times and calibration methods have been used in DVE-LS. Yet little is known about their effects on the accuracy of the obtained isotope values. The objective of this study was to evaluate how equilibration time and calibration methods affect the accuracy of DVE-LS. We did both spiking and field soil experiments. For the spiking experiment, we applied DVE-LS to four soils of different textures, each of which was subjected to five water contents and six equilibration times. For the field soil experiment, we applied three calibration methods for DVE-LS to two field soil profiles, and the results were compared with cryogenic vacuum distillation (CVD)-LS. Results showed that DVE-LS demonstrated higher δ²H and δ¹⁸O as equilibration time increased, but 12 to 24 hr could be used as optimal equilibration time. For field soil samples, DVE-LS with liquid waters as standards led to significantly higher δ²H and δ¹⁸O than CVD-LS, with root mean square error (RMSE) of 8.06‰ for δ²H and 0.98‰ for δ¹⁸O. Calibration with soil texture reduced RMSE to 3.53‰ and 0.72‰ for δ²H and δ¹⁸O, respectively. Further, calibration with both soil texture and water content decreased RMSE to 3.10‰ for δ²H and 0.73‰ for δ¹⁸O. Our findings conclude that the calibration method applied may affect the measured soil water isotope values from DVE-LS.  相似文献   

Estimating groundwater recharge for a freshwater lens in an arid region: Formative and stability assessment     

Mosaed S. Alrashidi  Ryan T. Bailey 《水文研究》2020,34(4):1063-1080

The formation of subsurface freshwater lenses on top of brackish groundwater is a fascinating hydrologic phenomenon that creates groundwater supplies of great potential value in arid regions. Information on the recharge quantity and mechanism of these lenses is both scarce and uncertain. This study examines the formation and macroscale stability of the Rawdatain freshwater lens in Kuwait, for which significant pre-development data are available. The Rawdatain is a large (150 million m³) subsurface freshwater lens overlying brackish groundwater compared to the other freshwater lenses in the Arabian Peninsula. In this study, a three-dimensional (3D) density-dependent groundwater flow model is tested against the following data targets to estimate long-term diffuse and focused groundwater recharge: (i) groundwater head, (ii) total dissolved solids (TDS) groundwater concentration, (iii) volume and vertical thickness of stored groundwater of three different water quality TDS ranges (0–700, 700–1000 and 1000–2000 mg/L) and (iv) geometrical shape features of the lens along cross-sections. To better represent the spatial variation in TDS, six different recharge zones were assigned to allocate diffuse and focused recharge conditions. Twelve recharge rate scenarios, encompassing a wide range of feasible long-term average annual recharge values (200,000–5,000,000 m³/year), were tested against the multiple targets and compared with the groundwater age of the Rawdatain lens. Based on comparison with data targets, the long-term average annual recharge is estimated to be 500,000 m³/year. Scenarios of reduced recharge, which may occur due to changes in land-use or climate, demonstrate the extremely slow response of the lens, which is in agreement with the slow development and formation of the lens (>2,000 years). Within a 100-year time frame, a 50% reduction in annual recharge reduces the lens volumes by 21, 17 and 9% for the three water quality categories, respectively. This study demonstrates the stability of freshwater lenses in arid regions and also provides methodology for similar focused rainfall recharge freshwater lenses.  相似文献   

粒子加速器中高精度丝线绝对位置测量技术研究   总被引：1，自引：0，他引：1  

梁静  罗明成  王铜  董岚  罗涛  柯志勇  王小龙 《测绘通报》2019,(9):44-50

粒子加速器中采用振动线技术进行共架单元上多块磁铁的高精度预准直，需要将振动线代表的磁中心引出进行共架单元之间的相对准直。为了获取以振动线为代表的丝线高精度空间绝对位置，本文对采用近景摄影测量技术进行点、线位置求解的方法进行了研究。利用单相机多站位的方法进行拍摄，通过标定板提供的高精度控制点坐标，采用自标定光束法平差对相机进行标定，并提出将空间直线离散成空间2点进行直线整体精确求解。对标定板上由2点组成的模拟直线进行测量验证，并与标定板提供的理论值进行对比，结果显示空间直线位置获取精度优于5 μm。这表明了本文理论和方法的正确性，为进一步研究丝线高精度空间绝对位置测量打下了基础。  相似文献   

基于投影变换的线阵旋转扫描相机标定方法     

苏琳  巫兆聪  闫钊  王鹏 《测绘通报》2019,(4):96-98,102

针对线阵旋转扫描相机标定数据难以获取及模型解算不稳定的问题，提出了一种基于投影变换的线阵旋转扫描相机标定方法。首先构建了一种新的线阵旋转扫描相机成像模型，该模型可以根据相机旋转平台参数、线阵旋转扫描相机成像平面与其切平面的位置关系将旋转扫描图像投影为框幅式图像；然后根据构建出的成像模型，采用直接线性变换法和非线性优化方法进行相机标定和参数优化。试验结果表明，此方法简单易行，具有较高的精度。  相似文献