利用海洋重力场变化分析洋底板块运动          下载免费PDF全文

李倩倩  鲍李峰  C. K. Shum 《地球物理学报》2020,63(7):2506-2515

洋底板块运动是地球动力学和全球变化研究的重要内容.本文根据质量迁移与地球外部重力场变化的对应关系,利用不同时期测高资料推算的1995—2019全球海洋重力场变化结果,反演分析全球洋底板块运动特征.研究表明,板块汇聚边界、板块内无震海岭、海山群、断裂带等区域重力异常变化显著,而在板块离散边界无明显变化趋势;西南印度洋中脊、大西洋中脊、中印度洋中脊等地区重力异常垂直梯度变化显著,且在西太平洋俯冲带、部分海岭区域也存在明显变化,其空间分布与地形基本吻合.海洋重力场变化整体上准确反映了全球洋底板块构造运动.相较于重力异常变化反演结果,重力垂直梯度的变化能够更为准确地反映洋底板块运动特征,特别是在洋中脊区域,扩张速率越小,垂直重力梯度变化越显著.此外,详细讨论了测高海洋重力场不确定因素对洋底板块运动分析结果的影响,海面坡度改正是主要因素之一.  相似文献   

Response of a scale-model pile group for a jacket foundation of an offshore wind turbine in liquefiable ground during shaking table tests     

Yung-Yen Ko  Yi-Ting Li 《地震工程与结构动力学》2020,49(15):1682-1701

To investigate the seismic response of a pile group during liquefaction, shaking table tests on a 1/25 scale model of a 2 × 2 pile group were conducted, which were pilot tests of a test project of a scale-model offshore wind turbine with jacket foundation. A large laminar shear box was utilized as the soil container to prepare a liquefiable sandy ground specimen. The pile group model comprising four slender aluminum piles with their pile heads connected by a rigid frame was designed with similitude considerations focusing on soil–pile interaction. The input motions were 2-Hz sinusoids with various acceleration amplitudes. The excess pore water pressure generation indicated that the upper half of the ground specimen reached initial liquefaction under the 50-gal-amplitude excitation, whereas in the 75-gal-amplitude test, almost entire ground was liquefied. Accelerations in soil, on the movable frames composing the laminar boundary of the shear box, and along the pile showed limited difference at the same elevation before liquefaction. After liquefaction, the soil and the movable-frame accelerations that represented the ground response considerably reduced, whereas both the movable frames and the piles exhibited high-frequency jitters other than 2-Hz sinusoid, and meantime, remarkable phase difference between the responses of the pile group and the ground was observed, all probably due to the substantial degradation of liquefied soil. Axial strains along the pile implied its double-curvature bending behavior, and the accordingly calculated moment declined significantly after liquefaction. These observations demonstrated the interaction between soil and piles during liquefaction.  相似文献   

An extended finite volume method and fixed-stress approach for modeling fluid injection–induced tensile opening in fractured reservoirs     

Rajdeep Deb  Patrick Jenny 《国际地质力学数值与分析法杂志》2020,44(8):1128-1144

Fluid injection–induced tensile opening is modeled using an extended finite volume method (XFVM). An embedded fracture strategy is used for the flow problem, that is, the fractures are discretized using finite volume segments without resolving the grid around them. Further, the discontinuities across fractures are modeled using special basis functions. The fracture openings due to enhanced fluid pressure and the associated shear slip due to traction free boundary condition on the fracture segments are both modeled using these special discontinuity basis functions. Mass transfer between fractures and matrix is modeled using the pressure difference. The enhancement of fracture storativity due to tensile opening leads to stronger coupling between flow and mechanics. An iterative scheme relying on the fixed-stress approach for fractures, which conserves the stress dependent terms over each iteration of the flow problem, has been introduced. Tensile opening has been simulated for single fractures embedded in two- and three-dimensional matrices. The convergence criterion for sequentially implicit fixed-stress scheme for fractures embedded in elastic media is established and has been validated numerically. Further, for 2D simulations, the effect of the matrix permeability for fracture propagation due to tensile opening has been studied.  相似文献   

筋土界面特性宏细观分析试验仪器研制与应用     

易富  杜常博  王政宇  于犇 《煤田地质与勘探》2020,48(1):174-182

为了更全面地分析筋土界面相互作用特性，改制了一台可视加筋土界面特性宏细观分析的试验仪器，可开展不同土工合成材料与填料的直剪和拉拔试验；该仪器改进了试验箱的尺寸，可方便两种试验的对比分析，增加了图像摄录系统，可进行试验过程的细观分析。使用新研制仪器分别进行了土工合成材料（土工格栅和土工布）加筋尾矿砂的直剪和拉拔试验，试验结果表明:两种试验条件下，土工格栅与尾矿的界面参数（似黏聚力和似摩擦角）及似摩擦系数均比土工布与尾矿的界面参数和似摩擦系数大；直剪试验下筋材网孔的有无对筋-尾矿界面参数均有较大影响，拉拔试验下筋材网孔有无对筋-尾矿界面参数似黏聚力的影响较为显著，对似摩擦角的影响较小。随着宏观变量法向应力的增加，细观参数孔隙率减小，平均接触数增加，反映在宏观上的现象就是填料颗粒被压密，筋材需要克服的阻力增大。该试验仪器能够较好地分析筋土界面宏细观特性，获得关键技术指标以用于加筋结构的设计。   相似文献   

基于新型高频声学多普勒流速剖面仪的河口近底部边界层观测初探     

兰庭飞  吴昊  唐杰平  李占海  汪亚平 《海洋通报》2019,38(6):640-649

河口物质输运、能量交换与底边界层内的水动力过程密切相关,底边界层参数(如切应力、拖曳系数)的确定至关重要。挪威Nortek公司生产的新型声学多普勒流速剖面仪AD2CP相比传统ADCP具有高频、低噪的优点,可用于高频(16Hz)流速剖面观测,而被广泛应用于底边界层观测的ADV只能测量单点高频流速。本文采用AD2CP在长江口南槽最大浑浊带区域进行座底式观测,并与同步近底部三脚架上ADV的观测结果进行对比。结果表明,使用AD2CP测得的近底部平均流速与ADV的测量结果吻合良好;使用惯性耗散法计算了底切应力,基于ADV的单点高频流速数据计算结果为2.16×10~(-2)～5.69×10~(-1)N/m~2,基于AD2CP的结果为2.09×10~(-2)～4.26×10~(-1)N/m~2,二者范围大致相当。在此基础上,基于AD2CP数据计算出摩阻流速为4.55×10~(-3)～2.06×10~(-2)m/s、底拖曳系数范围为1.84×10~(-4)～2.49×10~(-3),与ADV的计算结果基本一致。此外,由于AD2CP可以获得高频的流速剖面数据,优于单点ADV,具备观测近底部边界层参数和边界层内湍流剖面的潜力。  相似文献   

细粒含量对冰碛土抗剪强度影响的实验研究   总被引：1，自引：1，他引：0  

蒋德旺  崔鹏  王姣  李战鲁  殷延洲  雷鸣宇 《冰川冻土》2019,41(1):129-139

为研究细粒组颗粒在浸水/降雨条件下产生迁移对冰碛土抗剪强度的影响，从西藏林芝市帕隆藏布嘎隆寺沟流域内采取冰碛土样品，进行7种不同细粒（粒径小于2 mm）含量情况下的冰碛土比重和相对密度的测试，开展了不同围压下的大型饱和固结不排水三轴（CU）实验。结果表明：（1）细粒含量对干密度的影响较小，不同细粒含量的冰碛土孔隙比大致相同，细颗粒对孔隙具有改造作用，不同细粒含量会引起孔隙结构的差异，从而导致冰碛土的结构差异，最终导致抗剪强度的不同；（2）细颗粒迁移导致冰碛堤坡脚和内部一定深度细粒含量较高，达到一定的量值时，抗剪强度明显降低，冰碛堤容易发生剪切破坏；（3）细粒含量对抗剪强度参数的变化具有重要影响，从中还可以反映出冰碛土结构控制的变化：粗颗粒控制→粗细颗粒共同控制→细颗粒控制。研究结果对于评价冰碛堤的稳定性具有重要意义。  相似文献   

强震下混凝土剪力墙受弯模拟及测试实验研究          下载免费PDF全文

戴勤友  张正瑞 《地震工程学报》2020,42(2):337-344

为提高混凝土剪力墙受弯性能计算的准确度,开展强震下混凝土剪力墙受弯性能试验研究。选取1个混凝土剪力墙对比试件和3个测试试件作为研究对象,对试件施加垂直荷载和水平荷载,模拟强烈地震作用力。试验前期准备工作完成后,建立分离式有限元模型,通过计算混凝土在受压和受拉状态下的损伤弹塑性刚度,完成对有限元模型中混凝土塑性损伤分析,在此基础上,计算混凝土剪力墙受弯承载力。利用有限元模型对3个测试试件进行模拟试验,结果表明,强烈地震后3个试件的荷载-位移曲线均与实际位移值接近,且混凝土剪力墙受弯承载力试验结果与实际值的误差在2%以内,表明试验研究方法具有一定的可行性,数值模拟结果较为准确。  相似文献   

Moving from plot-based to hillslope-scale assessments of savanna vegetation structure with long-range terrestrial laser scanning (LR-TLS)     

《International Journal of Applied Earth Observation and Geoinformation》2020

Reliable quantification of savanna vegetation structure is critical for accurate carbon accounting and biodiversity assessment under changing climate and land-use conditions. Inventories of fine-scale vegetation structural attributes are typically conducted from field-based plots or transects, while large-area monitoring relies on a combination of airborne and satellite remote sensing. Both of these approaches have their strengths and limitations, but terrestrial laser scanning (TLS) has emerged as the benchmark for vegetation structural parameterization – recording and quantifying 3D structural detail that is not possible from manual field-based or airborne/spaceborne methods. However, traditional TLS approaches suffer from similar spatial constraints as field-based inventories. Given their small areal coverage, standard TLS plots may fail to capture the heterogeneity of landscapes in which they are embedded. Here we test the potential of long-range (>2000 m) terrestrial laser scanning (LR-TLS) to provide rapid and robust assessment of savanna vegetation 3D structure at hillslope scales. We used LR-TLS to sample entire savanna hillslopes from topographic vantage points and collected coincident plot-scale (1 ha) TLS scans at increasing distances from the LR-TLS station. We merged multiple TLS scans at the plot scale to provide the reference structure, and evaluated how 3D metrics derived from LR-TLS deviated from this baseline with increasing distance. Our results show that despite diluted point density and increased beam divergence with distance, LR-TLS can reliably characterize tree height (RMSE = 0.25–1.45 m) and canopy cover (RMSE = 5.67–15.91%) at distances of up to 500 m in open savanna woodlands. When aggregated to the same sampling grain as leading spaceborne vegetation products (10–30 m), our findings show potential for LR-TLS to play a key role in constraining satellite-based structural estimates in savannas over larger areas than traditional TLS sampling can provide.  相似文献   

Dynamic characteristics of marine soft clay under variable phase difference and initial static shear stress     

Wenqian Dong  Xiuqing Hu  Hongtao Fu 《Marine Georesources & Geotechnology》2020,38(7):770-785

Abstract

Under seismic loading, the soil layer is subjected to multidirectional cyclic shear stress with different amplitudes and frequencies because of the coupling of multiple shear waves and the soil element within a slope or behind a retaining wall is subjected to initial static shear stress before subjected to cyclic loading. Due to the complexity of seismic loading propagation, a phase difference exists between the initial static shear stress and cyclic shear stress. To investigate the influence of the phase difference and initial static shear stress on cyclic shear strain, cyclic modulus, and cyclic strength, a series of laboratory tests are performed on Wenzhou marine soft clay by multi-directional simple shear system, which can simulate the actual state better by controlling the horizontal cyclic stress in the x and y directions simultaneously. As the phase difference varies from 0° to 90°, the dynamic shear modulus increases and cyclic strain accumulation decreases with an increasing number of cycles. The shear strain increases with the initial shear stress.  相似文献   

Undrained monotonic shear behavior of marine soft clay after long-term cyclic loading     

Lin Guo  Hongxu Jin  Li Shi 《Marine Georesources & Geotechnology》2020,38(7):854-866

Abstract

In the coastal area, nearshore and offshore structures have been or will be built in marine soft clay deposits that have experienced long-term cyclic loads. Therefore, the mechanical behavior of marine clay after long-term cyclic loading needs to be investigated. In this research, a series of monotonic and cyclic triaxial tests were carried out to investigate the postcyclic mechanical behavior of the marine soft clay. The postcyclic water pore pressure, shear strength and secant stiffness are discussed by comparing the results with the standard monotonic test (without cyclic loading). It is very interesting that the postcyclic behavior of marine soft clay specimen is similar to the behavior of overconsolidated specimen, that is, the specimen shows apparent overconsolidation behavior after long-term cyclic loading. Then relationship between the overconsolidation ratio and the apparent overconsolidation ratio is established on the basis of the theory of equivalent overconsolidation. Finally, a validation formula is proposed which can predict the postcyclic undrained shear strength of marine soft clay.  相似文献