西藏冈底斯岩带曲水杂岩体锆石LA-ICP-MS U-Pb年龄及其地质意义     

次琼  永忠拉达  阿旺旦增  次仁吉 《沉积与特提斯地质》2020,40(2):116-128

曲水杂岩体位于冈底斯构造-岩浆岩带东段南缘,其岩浆活动与雅鲁藏布江新特提斯洋壳向北俯冲、消减以及印度与欧亚板块碰撞息息相关。本文以曲水县-昌果乡广泛分布的中酸性花岗岩体为研究对象,进行了系统的LA-ICP-MS锆石U-Pb年代学和岩石地球化学研究。结果表明,曲水杂岩体由3期时代和规模不同的花岗质岩体构成,其LA-ICP-MS锆石U-Pb年龄分别为95.2±1.0～88.5±1.0Ma、65.2±0.6Ma和48.5±0.5～43.3±0.7Ma;岩石地球化学研究表明,晚白垩世和古新世花岗岩以中性-中酸性为主,属钙碱性系列,具中铝特征,A/CNK比值小于1.1,属于I型花岗岩,是玄武质下地壳部分熔融产物,指示其形成于特提斯洋壳俯冲过程的岛弧构造环境。始新世花岗岩以高钾钙碱性系列为主,并出现钾玄岩系列,具偏铝-过铝质特征,指示岩浆上侵过程中遭受了不同程度的地壳物质混染,其形成于印度-欧亚板块强烈碰撞的构造环境。  相似文献   

Experimental investigation of seismic behaviour of the ancient Protiron monument model     

Željana Nikolić  Lidija Krstevska  Pavao Marović  Hrvoje Smoljanović 《地震工程与结构动力学》2019,48(6):573-593

Throughout history, dry-stone masonry structures have been strengthened with different types of metal connectors in order to increase their resistance which enabled their survival, especially in the seismically active area. One such example is the ancient Protiron monument placed in the Peristyle square of the Diocletian's Palace in Split, Croatia. The Protiron was built at the turn of the 3rd century as a stone masonry structure with dowels embedded between its base, columns, capitals and broad gable. The stone blocks in the broad gable were connected by metal clamps during restoration at the beginning of the 20th century. In order to study the seismic performance of the strengthened stone masonry structures, an experimental investigation of seismic behaviour of a physical model of the Protiron was performed on the shaking table. The model was designed as a true replica model in a length scale of 1:4 and exposed to representative earthquake with increasing intensities up to collapse. The tests provided a clear insight into system behaviour, damage mechanism and failure under intensive seismic load, especially into the efficiency of connecting elements, which had a special role in increasing seismic resistance and protection of the structure from collapse. Additionally, this experiment provided valuable data for verification and calibration of numerical models for strengthened stone masonry structures.  相似文献   

Real‐time force control for servo‐hydraulic actuator systems using adaptive time series compensator and compliance springs     

《地震工程与结构动力学》2018,47(4):854-871

Servo‐hydraulic actuators have been widely used for experimental studies in engineering. They can be controlled in either displacement or force control mode depending on the purpose of a test. It is necessary to control the actuators in real time when the rate‐dependency effect of a test specimen needs to be accounted for under dynamic loads. Real‐time hybrid simulation (RTHS) and effective force testing (EFT) method, which can consider the rate‐dependency effect, have been known as viable alternatives to the shake table testing method. Due to the lack of knowledge in real‐time force control, however, the structures that can be tested with RTHS and EFT are fairly limited. For instance, satisfying the force boundary condition for axially stiff members is a challenging task in RTHS, while EFT has a difficulty to be implemented for nonlinear structures. In order to resolve these issues, this paper introduces new real‐time force control methods utilizing the adaptive time series (ATS) compensator and compliance springs. Unlike existing methods, the proposed force control methods do not require the structural modeling of a test structure, making it easy to be implemented especially for nonlinear structures. The force tracking performance of the proposed methods is evaluated for a small‐scale steel mass block system with a magneto‐rheological damper subjected to various target forces. Accuracy, time delay, and resonance response of these methods are discussed along with their force control performance for an axially stiff member. Overall, a satisfactory force tracking performance was observed by using the proposed force control methods.  相似文献   

文莱-沙巴盆地深水褶皱冲断带构造变形特征及成因机制          下载免费PDF全文

唐武  赵志刚  张功成  谢晓军  刘世翔  王一博  宋双  王龙  孙瑞  郭佳 《地球物理学报》2018,61(10):4281-4295

为揭示活动陆缘深水褶皱冲断带的特征及成因，本文利用地震和区域地质资料的综合分析，系统阐述了文莱—沙巴盆地深水褶皱冲断带的构造变形特征，并结合盆地演化动力学特点，探讨其构造变形机制及其对深水区油气成藏的影响.研究结果表明，文莱—沙巴盆地深水褶皱冲断带具有"垂向分期、平面分段"的特点，垂向上，以中中新统底界面为界可划分为下部（始新世-早中新世）和上部（中中新世-现今）两套逆冲褶皱冲断体系，其中下部逆冲褶皱冲断带的形成与古南海的俯冲作用密切相关，上部逆冲褶皱冲断带是中中新世以来三角洲前缘重力滑动与苏禄海扩张造成的区域挤压应力远程效应共同作用的结果，且苏禄海扩张造成的远程挤压效应主控平面上南北段褶皱冲断带变形的差异性，导致北段褶皱变形强度大于南段，具有背斜褶皱数量多、褶皱间距离短、逆冲断层倾角陡的特点，南段反之；且晚上新世以来北段深水区地层缩短量大于陆架区伸展量，两者之差为2~6 km，而南段两者相当，仅受三角洲前缘重力滑动影响.整个褶皱冲断带发育断弯、断展、断滑褶皱等3种断层相关褶皱以及叠瓦扇和冲起构造2种逆冲构造组合，是多期NW向挤压应力作用下形成的大型逆冲推覆构造，以前展式向盆地扩展.此外，由于中中新世以来逆冲断层的持续活动，研究区深水褶皱冲断带发育众多构造圈闭，油气成藏条件优越，且南段优于北段，靠近陆坡的近端优于远端，可作为勘探部署重点.  相似文献   

The NE Directed Seismicity Belt in Tibet after the MS8.1 Nepal Earthquake and Its Predictive Significance     

Wang Shuangxu  Zhu Liangyu  Xu Jing  Ji Lingyun  Jiang Fengyun 《中国地震研究》2018,32(1):119-129

After the 2015 M_S8.1 Nepal earthquake, a strong and moderate seismicity belt has formed in Tibet gradually spreading along the northeast direction. In this paper, we attempt to summarize the features and investigate the primary mechanism of this behavior of seismic activity, using a 2-D finite element numerical model with tectonic dynamic settings and GPS horizontal displacements as the constraints. In addition, compared with the NE-trending seismicity belt triggered by the 1996 Xiatongmoin earthquake, we discuss the future earthquake hazard in and around Tibet. Our results show that:the NE-directed seismicity belt is the response of enhanced loading on the anisotropic Qinghai-Tibetan plateau from the Indian plate and earthquake thrusting. Also, this possibly implies that a forthcoming strong earthquake may fill in the gaps in the NE-directed seismicity belt or enhance the seismic hazard in the eastern (the north-south seismic zone) and western (Tianshan tectonic region) parts near the NE-directed belt.  相似文献   

Loading protocols for experimental seismic qualification of members in conventional and emerging steel frames     

Cheng Fang  Yiwei Ping  Yiyi Chen 《地震工程与结构动力学》2020,49(2):155-174

Quasi-static testing is one of the most commonly used experimental methods for examining the seismic performance of structural members. However, consistent loading protocols for experimental seismic qualification of members in emerging steel frames such as self-centering braced frames (SCBFs) as well as in some conventional ones including buckling-restrained braced frames (BRBFs) are still lacking. This paper aims to propose standardized loading protocols based on time-history dynamic analysis on a series of prototype building frames, including steel SCBFs, BRBFs, and moment-resisting frames (MRFs), where both far-field and near-fault earthquakes are considered. The methodology for the development of the loading protocols involves ground motion selection and scaling, design and analysis of prototype buildings, analysis results processing, and rainflow cycle counting, together with extra justification steps. The proposed loading protocols are consistently derived based on the MCE-level seismic hazard and 84^th percentile values of key seismic demand parameters. These parameters are number of damaging cycles N_t, maximum inter-story drift θ_max, inter-story drift range Δθ_i, sum of inter-story drift range ΣΔθ_i, and residual inter-story drift θ_r. The analysis confirms the variations in these seismic demands imposed on the different structural systems under different types of ground motions, highlighting the necessity of developing separate loading protocols for the different cases. The assumptions, decisions, and judgments made during the development of the loading protocols are elaborated, and the conditions and restrictions are outlined. The rationality of the proposed loading protocols is further justified through demonstrating the cumulative distribution function and energy dissipation demand of the systems.  相似文献   

冀中坳陷中部现今热岩石圈厚度及地热学意义探讨     

崔悦  朱传庆  邱楠生  唐博宁  郭飒飒 《地质学报》2020,94(7):1960-1969

热岩石圈厚度是研究盆地的构造演化和板块动力学的重要参数,本文通过实测数据构建地壳分层模型,根据热传导的基本原理,计算了冀中坳陷中部的Moho面温度以及热岩石圈厚度,并探讨其地热学意义。结果表明:冀中坳陷中部的Moho面温度分布在500～600℃,西南侧整体温度较东北部高,热岩石圈厚度介于102～122km,其平面展布特征与华北克拉通热岩石圈厚度西厚东薄的特征相吻合,为华北克拉通受太平洋板块西向俯冲导致东部遭受破坏提供了依据,并且较薄的岩石圈使热流更易传导到地壳浅部,成为了该地区热异常的成因背景。  相似文献   

Wave tank and bench-top control testing of a wave energy converter     

《Applied Ocean Research》2019

An increasing number of experiments are being conducted to study the design and performance of wave energy converters. Often in these tests, a real-time realization of prospective control algorithms is applied in order to assess and optimize energy absorption as well as other factors. This paper details the design and execution of an experiment for evaluating the capability of a model-scale WEC to execute basic control algorithms. Model-scale hardware, system, and experimental design are considered, with a focus on providing an experimental setup capable of meeting the dynamic requirements of a control system. To more efficiently execute such tests, a dry bench testing method is proposed and utilized to allow for controller tuning and to give an initial assessment of controller performance; this is followed by wave tank testing. The trends from the dry bench test and wave tank test results show good agreement with theory and confirm the ability of a relatively simple feedback controller to substantially improve energy absorption. Additionally, the dry bench testing approach is shown to be an effective and efficient means of designing and testing both controllers and actuator systems for wave energy converters.  相似文献   

An approach for shake table performance evaluation during repair and retrofit actions     

Christopher Trautner  Yewei Zheng  John S. McCartney  Tara Hutchinson 《地震工程与结构动力学》2018,47(1):131-146

Large‐scale, servo‐hydraulic shake tables are a central fixture of many earthquake engineering and structural dynamics laboratories. Wear and component failure from frequent use may lead to control problems resulting in reduced motion fidelity, necessitating repairs and replacement of major components. This paper presents a methodology to evaluate shake table performance pre‐ and post‐repair, including the definition of important performance metrics. The strategy suggested is presented in the context of the rebuilding of a 4.9 × 3.1 m, 350‐kN‐capacity uniaxial shake table. In this case, the rebuild consisted of characterization of wear to table components, replacement of worn bearing surfaces, and replacement of hydraulic accumulators. To assess the effectiveness of the repair actions, sinusoidal and triangular waves, white noise, and earthquake histories were run on the table before and after the rebuild. The repair actions were successful in reducing the position and velocity dependence of friction, improving the ability of control algorithms to accurately reproduce earthquake motions. The maximum and average response spectral misfits in the period range of 0.1–2 seconds were reduced from approximately 50% to 15%, and from 5% to less than 2.5%, respectively.  相似文献   

Effects of variation in loading protocol on the strength and deformation capacity of ductile reinforced concrete beams     

Kai J. Marder  Christopher J. Motter  Kenneth J. Elwood  G. Charles Clifton 《地震工程与结构动力学》2018,47(11):2195-2213

Understanding the impact of prior earthquake damage on residual capacity is important for postearthquake damage assessment of buildings; however, interpretation of such impact is challenging when based on tests using traditional reversed‐cyclic loading protocols. A new loading protocol, consisting of a dynamic earthquake displacement history followed by quasi‐static reversed‐cyclic loading to failure, is presented as an alternative to traditional simulated seismic loading protocols. Data are analyzed from a set of 12 nominally identical ductile reinforced concrete beams that were tested by using variations of this protocol and traditional reversed‐cyclic and monotonic protocols. Differences in the cycle content of the earthquake displacement histories applied to the test specimens allowed for the effects of load history variation below 2.2% drift to be isolated. It is found that such variation had no effect on the beam deformation capacities. The effects of dynamic loading rates are also analyzed and compared against control quasi‐static specimens. Relative strength increases due to dynamic loading are found to be more significant at yield than at ultimate. Dynamic loading rates led to modest reductions in the beam deformation capacities, but the presence of causality between these variables remains uncertain.  相似文献