Effectiveness of post-fire salvage logging stream buffer management for hillslope erosion in the U.S. Inland Northwest Mountains     

Peter R. Robichaud  Edwin D. Bone  Sarah A. Lewis  Erin S. Brooks  Robert E. Brown 《水文研究》2021,35(1):e13943

Active wildfire seasons in the western U.S. warrant the evaluation of post-fire forest management strategies. Ground-based salvage logging is often used to recover economic loss of burned timber. In unburned forests, ground-based logging often follows best management practices by leaving undisturbed areas near streams called stream buffers. However, the effectiveness of these buffers has not been tested in a post-wildfire setting. This experiment tested buffer width effectiveness with a novel field-simulated rill experiment using sediment-laden runoff (25 g/L) released over 40 min at evenly timed flow rates (50, 100 and 150 L/min) to measure surface runoff travel length and sediment concentration under unburned and high and low soil burn severity conditions at 2-, 10- and 22-month post-fire. High severity areas 2-month post-fire had rill lengths of up to 100 m. Rill length significantly decreased over time as vegetation regrowth provided ground cover. Sediment concentration and sediment dropout rate also varied significantly by soil burn severity. Sediment concentrations were 19 g/L for the highest flow 2-month post-fire and reduced to 6.9–14 g/L 10-month post-fire due to abundant vegetation recovery. The amount of sediment dropping out of the flow consistently increased over the study period with the low burn severity rate of 1.15 g L⁻¹ m⁻¹ approaching the unburned rate of 1.29 g L⁻¹ m⁻¹ by 2-year post-fire. These results suggest that an often-used standard, 15 m buffer, was sufficient to contain surface runoff and reduce sediment concentration on unburned sites, however buffers on high burn severity sites need to be eight times greater (120 m) immediately after wildfire and four times greater (60 m) 1-year post-fire. Low burn severity areas 1-year post-fire may need to be only twice the width of an unburned buffer (30 m), and 2-year post-fire these could return to unburned widths.  相似文献   

一种横观各向同性岩体蠕变模型     

李列列  管俊峰  肖明砾  刘海朝  唐克东 《岩土力学》2020,41(9):2922-2930

层状岩体由于层理面或者结构面的存在，在力学上具有横观各向同性的特点，现有的各向同性蠕变模型难以全面反映横观各向同性岩体的蠕变力学特性。为构建能够反映横观各向同性岩体的三维蠕变模型，以能反映瞬时应变、减速蠕变和稳态蠕变特征的黏弹性Burgers模型为基础，基于常泊松比假定，在三维各向同性蠕变本构方程的基础上，按照算子替换的方法，将横观各向同性柔度矩阵代替各向同性柔度矩阵，并考虑了平行和垂直层理方向岩体蠕变力学行为的差异性，推导了横观各向同性岩体的三维蠕变本构方程。根据本构方程的特点，提出了根据平行和垂直方向岩体蠕变试验结果进行三维蠕变本构模型中蠕变参数的辨识方法。将提出的模型应用于三轴蠕变试验参数辨识，从而获得了一套完整的三维蠕变参数，并与试验结果进行对比分析，从而验证了所提模型与方法的合理性和有效性。进一步，指出了传统蠕变试验设计方案的局限性，给出了横观各向同性材料蠕变试验设计建议。研究成果为研究岩体三维蠕变机制提供了新思路，可对岩体蠕变试验设计提供相应的科研支撑。  相似文献   

双座串联大跨度斜拉桥粘滞阻尼器参数分析          下载免费PDF全文

沈文爱  黄鸣柳  朱宏平  何友娣  张强 《世界地震工程》2020,(4):155-162

以双座串联大跨度斜拉桥-珠海洪鹤大桥为背景，根据桥梁自振特性及场地效应，生成了三组人工波，采用纵向+2/3竖向的地震作用组合输入方式，通过非线性时程分析，系统的研究了粘滞阻尼器对双座串联大跨度斜拉桥减震性能的影响。同时为了确定粘滞阻尼器的最优参数，对粘滞阻尼器的阻尼系数C和速度指数α进行了参数敏感性分析。结果表明:设置纵向粘滞阻尼器能够显著减小双座串联斜拉桥的纵向位移响应，减小主梁在串联处发生碰撞的概率，同时改善主塔塔底结构受力情况，具有良好的耗能减震效果。综合考虑安全性、适用性和经济性等方面，最后给出针对洪鹤大桥的最优粘滞阻尼器参数:速度指数α为0.3，阻尼系数C为3 000kN/（m/s）^0.3。  相似文献   

利用InSAR资料反演宁洱Ms6.4地震震源参数及库仑应力变化     

陈晨月  冯光财  高华  杨怀宁 《大地测量与地球动力学》2019,39(3):295-301

首先利用ALOS PALSAR数据，通过D-InSAR技术获取2007-06-03云南宁洱MS6.4地震的同震形变场，然后基于Okada弹性半空间位错模型反演该地震的断层几何以及精细滑动分布，最后计算宁洱地震后周边断层的静态库仑应力变化。结果表明，形变主要集中在西盘，最大视线向形变量为51.6 cm；反演得到的震源位置为23.05°N、101.02°E，深度3 km，断层走向145°，倾向49.5°，平均滑动角153°，发震断层为NNW向普洱断裂，断层活动以右旋走滑为主，兼具逆冲分量；断层面最大滑动量为1.2 m，反演得到的震级为MW619。基于库仑应力场发现，磨黑断裂处于库仑应力增加区域，而2014年景谷地震位于负值区域。结合实地考察资料和反演结果表明，宁洱地震为浅源地震，但断层并未出露地表。  相似文献   

Experimental investigation on a cabin-suspended catamaran in terms of motion reduction and wave energy harvesting by means of a semi-active motion control system     

《Applied Ocean Research》2019

A novel concept catamaran equipped with a suspended cabin, named Wave Harmonizer Type 4 (WHzer-4), is proposed and evaluated. The mass-spring-mass system is constructed by mounting four sets of suspensions in-between the cabin and the twin-hull. Two sets of dual motor/generators (M/Gs) are attached on the center beam of the cabin's deck fore and aft. Each shaft-end of the dual M/Gs is connected to the twin-hull through a rack-pinion gear unit. In this way the vertical relative motion between the cabin and the twin-hull can be transferred into the rotational motion of the M/Gs, and vice versa. A semi-active motion control system, which contains a proportional-integral (PI) controller, is designed and applied to each of the dual M/Gs for the aim of absorbing wave energy under the condition of suppressing the local vertical velocity of the cabin as much as possible. A 1/5 scale model ship with a length of 1.6 m is built, and a forced-oscillation bench test is implemented to validate the performance of the control system. Then, a series of towing tank tests is carried out in regular head waves. The heave and pitch responses of the cabin, those of the twin-hull and the corresponding wave energy capture width ratio (CWR) at five control scenarios and two reference scenarios are investigated. Discussion on the results of the tank test shows that the motion reduction of the cabin and the wave energy harvesting can be achieved simultaneously at a few wave conditions. However, at other conditions, although noticeable amount of wave energy is harvested, motion reduction of the heave and pitch of the cabin could not be obtained at the same time. It is suggested that varying the gain settings of the PI controllers according to the location of the controllers may improve the effectiveness of the proposed control system.  相似文献   

地中海直布罗陀海峡附近内孤立波的地球物理特征          下载免费PDF全文

孙绍箐  张锟  宋海斌 《地球物理学报》2019,62(7):2622-2632

本文主要利用地震海洋学方法研究地中海直布罗陀海峡附近内孤立波的结构特征，此处内孤立波为第一模态下沉型，为中幅度和大幅度内孤立波，垂向振幅最大可达74.5 m，振幅随深度增加呈增大趋势，传播速度随振幅增大而增大，可以确定"真"最大振幅位置位于密跃层附近.由于类多普勒效应和孤立波与测量船之间存在夹角的原因，从地震剖面上得到的为视半高宽参数，需要进行校正后才能得到比较真实的半高宽参数，校正后半高宽最高可达到1721.8 m，但是校正后的半高宽与理论结果有些差距，这可能与内孤立波的发育稳定程度有关.随着内孤立波包不断向东运动，整体波宽变大，垂向速度变小.本文将地震海洋学方法拓展应用于地中海区域内孤立波分析，进一步证明了利用地震海洋学方法研究海水运动的可行性.  相似文献   

Seismic amplitude inversion for the transversely isotropic media with vertical axis of symmetry     

Feng Zhang  Tuo Zhang  Xiang-Yang Li 《Geophysical Prospecting》2019,67(9):2368-2385

Transverse isotropy with a vertical axis of symmetry is a common form of anisotropy in sedimentary basins, and it has a significant influence on the seismic amplitude variation with offset. Although exact solutions and approximations of the PP-wave reflection coefficient for the transversely isotropic media with vertical axis of symmetry have been explicitly studied, it is difficult to apply these equations to amplitude inversion, because more than three parameters need to be estimated, and such an inverse problem is highly ill-posed. In this paper, we propose a seismic amplitude inversion method for the transversely isotropic media with a vertical axis of symmetry based on a modified approximation of the reflection coefficient. This new approximation consists of only three model parameters: attribute A, the impedance (vertical phase velocity multiplied by bulk density); attribute B, shear modulus proportional to an anellipticity parameter (Thomsen's parameter ε−δ); and attribute C, the approximate horizontal P-wave phase velocity, which can be well estimated by using a Bayesian-framework-based inversion method. Using numerical tests we show that the derived approximation has similar accuracy to the existing linear approximation and much higher accuracy than isotropic approximations, especially at large angles of incidence and for strong anisotropy. The new inversion method is validated by using both synthetic data and field seismic data. We show that the inverted attributes are robust for shale-gas reservoir characterization: the shale formation can be discriminated from surrounding formations by using the crossplot of the attributes A and C, and then the gas-bearing shale can be identified through the combination of the attributes A and B. We then propose a rock-physics-based method and a stepwise-inversion-based method to estimate the P-wave anisotropy parameter (Thomsen's parameter ε). The latter is more suitable when subsurface media are strongly heterogeneous. The stepwise inversion produces a stable and accurate Thomsen's parameter ε, which is proved by using both synthetic and field data.  相似文献   

Modeling spatially non-stationary land use/cover change in the lower Connecticut River Basin by combining geographically weighted logistic regression and the CA-Markov model   总被引：2，自引：0，他引：2  

Hui Wang  Scott R. Stephenson  Shijin Qu 《International journal of geographical information science》2019,33(7):1313-1334

Simulating land use/cover change (LUCC) and determining its transition rules have been a focus of research for several decades. Previous studies used ordinary logistic regression (OLR) to determine transition rules in cellular automata (CA) modeling of LUCC, which often neglected the spatially non-stationary relationships between driving factors and land use/cover categories. We use an integrated geographically weighted logistic regression (GWLR) CA-Markov method to simulate LUCC from 2001–2011 over 29 towns in the Connecticut River Basin. Results are compared with those obtained from the OLR-CA-Markov method, and the sensitivity of LUCC simulated by the GWLR-CA-Markov method to the spatial non-stationarity-based suitability map is investigated. Analysis of residuals indicates better goodness of fit in model calibration for geographically weighted regression (GWR) than OLR. Coefficients of driving factors indicate that GWLR outperforms OLR in depicting the local suitability of land use/cover categories. Kappa statistics of the simulated maps indicate high agreement with observed land use/cover for both OLR-CA-Markov and GWLR-CA-Markov methods. Similarity in simulation accuracy between the methods suggests that the sensitivity of simulated LUCC to suitability inputs is low with respect to spatial non-stationarity. Therefore, this study provides critical insight on the role of spatial non-stationarity throughout the process of LUCC simulation.  相似文献   

考虑填充墙影响的钢筋混凝土厂房结构地震易损性分析     

梁志强  徐超  温增平 《震灾防御技术》2019,14(4):707-718

采用对角斜撑模拟纵向填充墙的作用，建立考虑填充墙和不考虑填充墙厂房结构模型，采用拉丁超立方抽样技术建立考虑材料不确定性的结构分析样本，基于随机Pushover分析确定结构不同破坏状态下的统计参数。综合考虑结构材料强度及输入地震动不确定性的影响，通过非线性时程分析开展单层钢筋混凝土厂房结构易损性研究，在此基础上比较结构横、纵向易损性的差异，研究填充墙对结构易损性的影响。研究结果表明:钢筋混凝土厂房结构体系横向地震易损性显著大于纵向地震易损性；对纵向结构体系而言，加入填充墙会明显降低结构易损性，但在相同强度的地震动作用下，填充墙破坏程度比主体结构严重，这与厂房结构的实际震害特征相符。  相似文献   

多层构造油藏纵向细分计算单元对储量参数及结果的影响     

颜冠山  刘宗宾  宋洪亮  韩雪芳  王欣然 《地质与资源》2020,29(4):342-350

为满足油田中后期精细开发及后续调整挖潜的需要，亟需进行更精细的储量研究，其中最重要的一环就是纵向细分计算单元.对于多层构造油藏，纵向细分主要根据油层组内隔夹层分布特征、小层物性特征，细分到以小层或者分布特征和物性相近且纵向上连续分布的小层组合为计算单元.根据纵向细分计算单元前后储量参数选值的理论推导，结合储层的沉积展布特征，认为含油面积范围内无储层尖灭时，仅平面油层厚度差异较大的油藏平均有效厚度变小.含油面积范围内储层尖灭时，正常三角洲沉积储层的油藏各参数一般都变小；而辫状河三角洲沉积储层的油藏一般平均有效厚度变小，平均有效孔隙度和平均含油饱和度变大.这一结论可以有效指导储量评估过程中纵向细分计算单元方案划分，为同类油田的精细储量研究提供技术支撑.  相似文献