考虑冲刷影响的筒型基础竖向极限承载力研究     

陆罗观  刘润  练继建  陈广思 《海洋工程》2019,37(3):69-77

大直径宽浅式筒型基础,阻水宽度大,在位工作期间受波浪海流作用,其周围土体易被冲刷。为研究单侧地基土体受冲刷后筒型基础的竖向极限承载力变化,通过引进冲刷率的概念,采用有限元方法研究了不同冲刷率下筒型基础的竖向极限承载力;并基于Meyerhof理论建立了计算不同冲刷率下筒型基础竖向极限承载力的极限平衡方法。研究结果表明,随着冲刷率增大,筒型基础的极限承载力出现不同程度的下降,当冲刷率为0.8时,即筒型基础单侧土体冲刷深度达6.4 m时,筒型基础的竖向极限承载力折减率为3.28%。建立的极限平衡算法可准确计算冲刷条件下筒型基础的竖向极限承载力。  相似文献   

Climatic signals in lacustrine deposits of the Upper Yacoraite Formation,Western Argentina: Evidence from clay minerals,analcime, dolomite and fibrous calcite     

João Paulo B. Gomes  Rodrigo B. Bunevich  Sandra N. Tonietto  Daisy B. Alves  Julice F. Santos  Fiona F. Whitaker 《Sedimentology》2020,67(5):2282-2309

Authigenic clays are an important control on reservoir quality in lacustrine carbonates but remain challenging to predict. Lacustrine depositional systems respond to climatic variations in rainfall, surface runoff and groundwater input, and evaporation, and result in rapid and frequent changes in lake volume; this is expressed through changing water depth and shoreline position. In the upper portion of the Early Palaeocene Yacoraite Formation of the Salta Basin in Argentina, extensive lacustrine deposits were deposited during the sag phase of rifting. Prior high-resolution stratigraphic studies have suggested that climatic factors control microbial carbonate sequences within a ‘balanced fill’ lake, with variation in the lake level having a major influence on facies association changes. This study characterizes the evolution of facies and mineralogy within the Yacoraite Formation, focusing on the distribution of clay minerals, making a link between the high, medium and low-frequency sequence stratigraphic cycles. The low-frequency transgressive hemicycle of the upper portion of the Yacoraite Formation is comprised of abundant siliciclastic facies, suggesting a wetter period. Microbialites occurring in this interval are coarse-grained and agglutinated. Detrital clay minerals such as illite and chlorite and associated siliciclastic sediments were input to the lake during high-frequency transgressive periods. During high-frequency regressive hemicycles, sedimentation was dominated by carbonate facies with Ca-rich dolomite and the authigenic clays are comprised of chlorite/smectite mixed-layers. By contrast, the low frequency regressive hemicycle records fine-grained agglutinated microbialite with horizons of fibrous calcite, more stoichiometric dolomite, barite and authigenic magnesian smectite. This indicates elevated ion concentrations in the lake under intense evaporation during an arid period. Understanding the conditions that are favourable for formation and preservation of authigenic clays within the lacustrine environment can improve understanding of reservoir quality in comparable economically important deposits.  相似文献   

A finite element approach for predicting the full resistance profile of a spudcan deeply penetrating in dense sand overlying clay     

《Applied Ocean Research》2019

This paper presents a finite element approach to calculate the full resistance profile of a spudcan deeply penetrating in dense sand overlying clay, in which a potential for an installing spudcan to experience a sudden uncontrolled punch-through failure exists. A modified Mohr-Coulomb model characterized by incorporating a four-phase variation of the mobilized strength and dilation parameters with an equivalent accumulated plastic strain is developed and tested for the overlying dense silica sand. An extended Tresca model is used for the strain softening of the underlying clay. A series of large deformation finite-element (LDFE) analyses are carried out, varying the strength and dilation parameters as well as the spudcan geometries. A fairly good performance of the present approach is verified by validating against groups of centrifuge tests data, allowing the numerical study to be extended parametrically. The four-phase variation of the mobilized strength and dilation parameters involved in the progressive failure of the upper dense sand is parametrically studied and extended to cover the range of sand relative densities that are of practical interest. Additionally, comparisons with the typical existing LDFE analyses using both simple and sophisticated constitutive models are carried out. It shows that the present approach performs fairly well to calculate the full resistance profile of a spudcan deeply penetration in both thin and thick dense sand overlying clay, especially the peak and post-peak resistance, within around 5% of the corresponding centrifuge tests results.  相似文献   

Dynamic characteristics of marine soft clay under variable phase difference and initial static shear stress     

Wenqian Dong  Xiuqing Hu  Hongtao Fu 《Marine Georesources & Geotechnology》2020,38(7):770-785

Abstract

Under seismic loading, the soil layer is subjected to multidirectional cyclic shear stress with different amplitudes and frequencies because of the coupling of multiple shear waves and the soil element within a slope or behind a retaining wall is subjected to initial static shear stress before subjected to cyclic loading. Due to the complexity of seismic loading propagation, a phase difference exists between the initial static shear stress and cyclic shear stress. To investigate the influence of the phase difference and initial static shear stress on cyclic shear strain, cyclic modulus, and cyclic strength, a series of laboratory tests are performed on Wenzhou marine soft clay by multi-directional simple shear system, which can simulate the actual state better by controlling the horizontal cyclic stress in the x and y directions simultaneously. As the phase difference varies from 0° to 90°, the dynamic shear modulus increases and cyclic strain accumulation decreases with an increasing number of cycles. The shear strain increases with the initial shear stress.  相似文献   

Undrained monotonic shear behavior of marine soft clay after long-term cyclic loading     

Lin Guo  Hongxu Jin  Li Shi 《Marine Georesources & Geotechnology》2020,38(7):854-866

Abstract

In the coastal area, nearshore and offshore structures have been or will be built in marine soft clay deposits that have experienced long-term cyclic loads. Therefore, the mechanical behavior of marine clay after long-term cyclic loading needs to be investigated. In this research, a series of monotonic and cyclic triaxial tests were carried out to investigate the postcyclic mechanical behavior of the marine soft clay. The postcyclic water pore pressure, shear strength and secant stiffness are discussed by comparing the results with the standard monotonic test (without cyclic loading). It is very interesting that the postcyclic behavior of marine soft clay specimen is similar to the behavior of overconsolidated specimen, that is, the specimen shows apparent overconsolidation behavior after long-term cyclic loading. Then relationship between the overconsolidation ratio and the apparent overconsolidation ratio is established on the basis of the theory of equivalent overconsolidation. Finally, a validation formula is proposed which can predict the postcyclic undrained shear strength of marine soft clay.  相似文献   

塑性极限分析鱼雷锚锚尖贯入阻力     

瑜璐  杨庆  杨钢  张金利 《岩土力学》2020,41(6):1953-1962

鱼雷锚安装过程中,锚尖形状影响尖部贯入阻力进而影响贯入深度。基于塑性极限分析理论下限法分析不同锚尖长径比x的椭圆形锚尖的贯入阻力和贯入阻力系数,并考虑了贯入深度、锚-土界面摩擦对贯入阻力以及贯入阻力系数的影响。结果表明:(1)锚-土界面光滑时,锚尖贯入阻力系数随着锚尖长径比的增大而减小;锚-土界面粗糙时,锚尖贯入阻力系数随着锚尖长径比的增大而增大。(2)摩擦力对贯入阻力系数的影响随着ξ增大而增大。(3)随着埋置深度增加,贯入阻力系数受x影响最小时所对应的摩擦系数逐渐减小。(4)当锚-土界面摩擦系数ω 0.75时,工程中可选用ξ1的锚尖用以减小端部贯入阻力;当ω0.26时,ξ1的锚尖提供更小的端部贯入阻力。锚尖长径比ξ=0和ξ=1的下限解与前人研究的桩基和圆形结构的理论解较为一致,进一步验证了所提出的椭圆形锚尖下限法模型的可行性。  相似文献   

冻融循环对土体强度变形参数的影响          下载免费PDF全文

张渭军 《探矿工程》2020,47(6):86-91

在寒区工程建设中，冻融循环会引起土强度和变形特性发生改变。为了研究多次冻融循环后土的强度和变形参数的变化量，本文以冻融和非冻融的粉质粘土饱和试样为研究对象，通过固结排水三轴剪切试验、三轴等向压缩试验和弹性模量试验，比较了冻融循环对土样强度参数和变形参数的影响。试验结果显示：冻融和非冻融试样的应力—应变关系曲线均呈应变硬化型，对于原状试样冻融作用破坏了其结构性；冻融作用导致土体强度的降低，主要体现在粘聚力的降低，约降低了55.6%；冻融循环对变形参数有明显的影响，其中最明显的是弹性模量的降低，降低了31.2%。该研究结论可为工程冻害处理提供参考，也可为相关研究的数值计算提供试验参数。  相似文献   

Microstructure Evolution of Organic Matter and Clay Minerals in Shales with Increasing Thermal Maturity     

GU Yuantao  LI Xiaoxi  YANG Shuguang  WAN Quan 《《地质学报》英文版》2020,94(2):280-289

As the two important components of shale, organic matter(OM) and clay minerals are usually thought to strongly influence the hydrocarbon generation, enrichment and exploitation. The evolution process of OM and clay minerals as well as their interrelationship over a wide range of thermal maturities are not completely clear. Taking Yanchang(T_3y), Longmaxi(S_1l) and Niutitang(?_1n) shales as examples, we have studied the microstructure characteristics of OM and clay minerals in shales with different thermal maturities. The effects of clay minerals and OM on pores were reinforced through sedimentation experiments. Using a combination of field emission scanning electron microscopy(FESEM) and low-pressure N_2 adsorption, we investigated the microstructure differences among the three shales. The results showed that both OM and clay minerals have strong effects on pores, and small mesopore(2–20 nm) is the dominant pore component for all three samples. However, the differences between the three samples are embodied in the distribution of pore size and the location. For the T_3y shale, clay minerals are loosely arranged and develop large amounts of pores, and fine OM grains often fill in intergranular minerals or fractures. Widespread OM pores distribute irregularly in S_1l shale, and most of the pores are elliptical and nondirectional. The ?_1n shale is characterized by the preferred orientational OM-clay aggregates, and lots of pores in the composites are in the mesopore range, suggesting that over maturity lead to the collapse and compaction of pores under huge pressure of strata. The results of the current research imply that with increasing thermal maturity, OM pores are absent at low maturity(T_3y), are maximized at high maturity(S_1l) and are destroyed or compacted at over-mature stage(?_1n). Meanwhile, clay minerals have gone through mineral transformation and orientational evolution. The interaction of the two processes makes a significant difference to the microstructure evolution of OM and clay minerals in shale, and the findings provide scientific foundation in better understanding diagenetic evolution and hydrocarbon generation of shale.  相似文献   

Effect of nano-MgO on mechanical performance of cement stabilized silty clay     

Kai Yao  Dongliang An  Na Li  Chen Zhang  Aizhao Zhou 《Marine Georesources & Geotechnology》2020,38(2):250-255

Abstract

A series of direct shear tests were performed on cement-admixed silty clay to investigate the effect of cement content and nano-magnesia (MgO) on its shear strength properties. For each normal stress, shear strength increased with cement content. However, an obvious increment in shear strength was achieved when the cement content was adjusted from 13% to 17%. Both cohesion and friction angle of cemented soil increased with cement content, and exponential function was adopted to correlate both the factors with cement content. For cement content of 10% investigated in this study, the optimum nano-MgO content was 10‰, wherein the cohesion could reach the peak value. The microstructure of the mixture revealed that the structure of the mixture was compacted for the optimum nano-MgO content. However, micro-cracks were formed when the amount of nano-MgO exceeded its optimum content.  相似文献   

Unified numerical study of shallow foundation on structured soft clay under unconsolidated and consolidated-undrained loadings     

Santosh Kumar Yadav  Guan-lin Ye  Usama Khalid 《Marine Georesources & Geotechnology》2020,38(4):400-416

Abstract

Based on a new elasto-plastic constitutive model, this paper presents a soil–water coupled numerical prediction of the bearing capacity for shallow foundation constructed on Ballina soft clay for unconsolidated undrained (UU) and consolidated undrained (CU) conditions. This elasto-plastic constitutive Shanghai model has an advantage of describing the mechanical behaviour of over-consolidated and structured soil under different loading and drainage conditions, by using one set of material parameter. In this paper, the Shanghai model used for both UU and CU conditions has the same initial parameters obtained from laboratory test results. The loading conditions and consolidation stages vary based on construction details. The predicted bearing pressure-settlement responses for UU and CU, approves the field observation. The phenomenon of gaining the bearing capacity due to consolidation is captured and explained by the use of soil–water coupled numerical analysis with a new elasto-plastic model. The stress strain behaviour, stress paths and the decay of the structure of elements at different depths presented in this study, reveal the mechanism for the difference between UU and CU conditions to understand the foundation behaviour. Effect of the initial degree of soil structure on the bearing capacity is also addressed. Overall, this approach provides the integrated solution for the shallow foundation design problems under short and long-term loadings.  相似文献