Response of a scale-model pile group for a jacket foundation of an offshore wind turbine in liquefiable ground during shaking table tests     

Yung-Yen Ko  Yi-Ting Li 《地震工程与结构动力学》2020,49(15):1682-1701

To investigate the seismic response of a pile group during liquefaction, shaking table tests on a 1/25 scale model of a 2 × 2 pile group were conducted, which were pilot tests of a test project of a scale-model offshore wind turbine with jacket foundation. A large laminar shear box was utilized as the soil container to prepare a liquefiable sandy ground specimen. The pile group model comprising four slender aluminum piles with their pile heads connected by a rigid frame was designed with similitude considerations focusing on soil–pile interaction. The input motions were 2-Hz sinusoids with various acceleration amplitudes. The excess pore water pressure generation indicated that the upper half of the ground specimen reached initial liquefaction under the 50-gal-amplitude excitation, whereas in the 75-gal-amplitude test, almost entire ground was liquefied. Accelerations in soil, on the movable frames composing the laminar boundary of the shear box, and along the pile showed limited difference at the same elevation before liquefaction. After liquefaction, the soil and the movable-frame accelerations that represented the ground response considerably reduced, whereas both the movable frames and the piles exhibited high-frequency jitters other than 2-Hz sinusoid, and meantime, remarkable phase difference between the responses of the pile group and the ground was observed, all probably due to the substantial degradation of liquefied soil. Axial strains along the pile implied its double-curvature bending behavior, and the accordingly calculated moment declined significantly after liquefaction. These observations demonstrated the interaction between soil and piles during liquefaction.  相似文献   

An extended finite volume method and fixed-stress approach for modeling fluid injection–induced tensile opening in fractured reservoirs     

Rajdeep Deb  Patrick Jenny 《国际地质力学数值与分析法杂志》2020,44(8):1128-1144

Fluid injection–induced tensile opening is modeled using an extended finite volume method (XFVM). An embedded fracture strategy is used for the flow problem, that is, the fractures are discretized using finite volume segments without resolving the grid around them. Further, the discontinuities across fractures are modeled using special basis functions. The fracture openings due to enhanced fluid pressure and the associated shear slip due to traction free boundary condition on the fracture segments are both modeled using these special discontinuity basis functions. Mass transfer between fractures and matrix is modeled using the pressure difference. The enhancement of fracture storativity due to tensile opening leads to stronger coupling between flow and mechanics. An iterative scheme relying on the fixed-stress approach for fractures, which conserves the stress dependent terms over each iteration of the flow problem, has been introduced. Tensile opening has been simulated for single fractures embedded in two- and three-dimensional matrices. The convergence criterion for sequentially implicit fixed-stress scheme for fractures embedded in elastic media is established and has been validated numerically. Further, for 2D simulations, the effect of the matrix permeability for fracture propagation due to tensile opening has been studied.  相似文献   

筋土界面特性宏细观分析试验仪器研制与应用     

易富  杜常博  王政宇  于犇 《煤田地质与勘探》2020,48(1):174-182

为了更全面地分析筋土界面相互作用特性，改制了一台可视加筋土界面特性宏细观分析的试验仪器，可开展不同土工合成材料与填料的直剪和拉拔试验；该仪器改进了试验箱的尺寸，可方便两种试验的对比分析，增加了图像摄录系统，可进行试验过程的细观分析。使用新研制仪器分别进行了土工合成材料（土工格栅和土工布）加筋尾矿砂的直剪和拉拔试验，试验结果表明:两种试验条件下，土工格栅与尾矿的界面参数（似黏聚力和似摩擦角）及似摩擦系数均比土工布与尾矿的界面参数和似摩擦系数大；直剪试验下筋材网孔的有无对筋-尾矿界面参数均有较大影响，拉拔试验下筋材网孔有无对筋-尾矿界面参数似黏聚力的影响较为显著，对似摩擦角的影响较小。随着宏观变量法向应力的增加，细观参数孔隙率减小，平均接触数增加，反映在宏观上的现象就是填料颗粒被压密，筋材需要克服的阻力增大。该试验仪器能够较好地分析筋土界面宏细观特性，获得关键技术指标以用于加筋结构的设计。   相似文献   

基于新型高频声学多普勒流速剖面仪的河口近底部边界层观测初探     

兰庭飞  吴昊  唐杰平  李占海  汪亚平 《海洋通报》2019,38(6):640-649

河口物质输运、能量交换与底边界层内的水动力过程密切相关,底边界层参数(如切应力、拖曳系数)的确定至关重要。挪威Nortek公司生产的新型声学多普勒流速剖面仪AD2CP相比传统ADCP具有高频、低噪的优点,可用于高频(16Hz)流速剖面观测,而被广泛应用于底边界层观测的ADV只能测量单点高频流速。本文采用AD2CP在长江口南槽最大浑浊带区域进行座底式观测,并与同步近底部三脚架上ADV的观测结果进行对比。结果表明,使用AD2CP测得的近底部平均流速与ADV的测量结果吻合良好;使用惯性耗散法计算了底切应力,基于ADV的单点高频流速数据计算结果为2.16×10~(-2)～5.69×10~(-1)N/m~2,基于AD2CP的结果为2.09×10~(-2)～4.26×10~(-1)N/m~2,二者范围大致相当。在此基础上,基于AD2CP数据计算出摩阻流速为4.55×10~(-3)～2.06×10~(-2)m/s、底拖曳系数范围为1.84×10~(-4)～2.49×10~(-3),与ADV的计算结果基本一致。此外,由于AD2CP可以获得高频的流速剖面数据,优于单点ADV,具备观测近底部边界层参数和边界层内湍流剖面的潜力。  相似文献   

细粒含量对冰碛土抗剪强度影响的实验研究   总被引：1，自引：1，他引：0  

蒋德旺  崔鹏  王姣  李战鲁  殷延洲  雷鸣宇 《冰川冻土》2019,41(1):129-139

为研究细粒组颗粒在浸水/降雨条件下产生迁移对冰碛土抗剪强度的影响，从西藏林芝市帕隆藏布嘎隆寺沟流域内采取冰碛土样品，进行7种不同细粒（粒径小于2 mm）含量情况下的冰碛土比重和相对密度的测试，开展了不同围压下的大型饱和固结不排水三轴（CU）实验。结果表明：（1）细粒含量对干密度的影响较小，不同细粒含量的冰碛土孔隙比大致相同，细颗粒对孔隙具有改造作用，不同细粒含量会引起孔隙结构的差异，从而导致冰碛土的结构差异，最终导致抗剪强度的不同；（2）细颗粒迁移导致冰碛堤坡脚和内部一定深度细粒含量较高，达到一定的量值时，抗剪强度明显降低，冰碛堤容易发生剪切破坏；（3）细粒含量对抗剪强度参数的变化具有重要影响，从中还可以反映出冰碛土结构控制的变化：粗颗粒控制→粗细颗粒共同控制→细颗粒控制。研究结果对于评价冰碛堤的稳定性具有重要意义。  相似文献   

强震下混凝土剪力墙受弯模拟及测试实验研究          下载免费PDF全文

戴勤友  张正瑞 《地震工程学报》2020,42(2):337-344

为提高混凝土剪力墙受弯性能计算的准确度,开展强震下混凝土剪力墙受弯性能试验研究。选取1个混凝土剪力墙对比试件和3个测试试件作为研究对象,对试件施加垂直荷载和水平荷载,模拟强烈地震作用力。试验前期准备工作完成后,建立分离式有限元模型,通过计算混凝土在受压和受拉状态下的损伤弹塑性刚度,完成对有限元模型中混凝土塑性损伤分析,在此基础上,计算混凝土剪力墙受弯承载力。利用有限元模型对3个测试试件进行模拟试验,结果表明,强烈地震后3个试件的荷载-位移曲线均与实际位移值接近,且混凝土剪力墙受弯承载力试验结果与实际值的误差在2%以内,表明试验研究方法具有一定的可行性,数值模拟结果较为准确。  相似文献   

Dynamic characteristics of marine soft clay under variable phase difference and initial static shear stress     

Wenqian Dong  Xiuqing Hu  Hongtao Fu 《Marine Georesources & Geotechnology》2020,38(7):770-785

Abstract

Under seismic loading, the soil layer is subjected to multidirectional cyclic shear stress with different amplitudes and frequencies because of the coupling of multiple shear waves and the soil element within a slope or behind a retaining wall is subjected to initial static shear stress before subjected to cyclic loading. Due to the complexity of seismic loading propagation, a phase difference exists between the initial static shear stress and cyclic shear stress. To investigate the influence of the phase difference and initial static shear stress on cyclic shear strain, cyclic modulus, and cyclic strength, a series of laboratory tests are performed on Wenzhou marine soft clay by multi-directional simple shear system, which can simulate the actual state better by controlling the horizontal cyclic stress in the x and y directions simultaneously. As the phase difference varies from 0° to 90°, the dynamic shear modulus increases and cyclic strain accumulation decreases with an increasing number of cycles. The shear strain increases with the initial shear stress.  相似文献   

Undrained monotonic shear behavior of marine soft clay after long-term cyclic loading     

Lin Guo  Hongxu Jin  Li Shi 《Marine Georesources & Geotechnology》2020,38(7):854-866

Abstract

In the coastal area, nearshore and offshore structures have been or will be built in marine soft clay deposits that have experienced long-term cyclic loads. Therefore, the mechanical behavior of marine clay after long-term cyclic loading needs to be investigated. In this research, a series of monotonic and cyclic triaxial tests were carried out to investigate the postcyclic mechanical behavior of the marine soft clay. The postcyclic water pore pressure, shear strength and secant stiffness are discussed by comparing the results with the standard monotonic test (without cyclic loading). It is very interesting that the postcyclic behavior of marine soft clay specimen is similar to the behavior of overconsolidated specimen, that is, the specimen shows apparent overconsolidation behavior after long-term cyclic loading. Then relationship between the overconsolidation ratio and the apparent overconsolidation ratio is established on the basis of the theory of equivalent overconsolidation. Finally, a validation formula is proposed which can predict the postcyclic undrained shear strength of marine soft clay.  相似文献   

场地类别分类方案研究     

陈国兴  丁杰发  方怡  彭艳菊  李小军 《岩土力学》2020,41(11):3509-3522

基于性能的抗震设计，要求工程师设计出具有预期抗震性能的结构，一个关键因素是地震作用的确定，这在很大程度上取决于局部场地条件。通过收集和分析北京、苏州和唐山城区956个钻孔资料，建立地表20 m和30 m深土层走时平均剪切波速VS20和VS30的关系式；现场钻探获取北京城区深105 m的典型钻孔原状土样，试验给出各类土体动剪切模量和阻尼比曲线；建立北京城区170个钻孔的场地反应计算模型，采用Nakamura提出的HVSR法和陈国兴等提出的弱震法估算场地基本周期TS值，结合国内外现行抗震规范的场地分类及一些学者对场地分类的研究成果，提出两种新的场地分类建议方案：基于等效剪切波速VSE和覆盖土层厚度H（地表至剪切波速VS ≥ 500 m/s的基岩深度）的双指标场地分类方案及基于VSE、H和TS的三指标场地分类方案。提出的场地分类方案对我国现行抗震规范场地分类方法的改进有参考价值。  相似文献   

盾构隧道下穿管道施工引起的管-土相互作用研究     

可文海  管凌霄  刘东海  邓建林  李科  徐长节 《岩土力学》2020,41(1):221-228

采用Loganathan公式研究了盾构隧道下穿管道施工引起的地下管道处土体竖向位移，利用考虑土中剪力传递的Pasternak模型模拟管-土相互作用，运用修正Vlasov模型中的迭代流程计算出Pasternak模型的关键参数——弹性系数k与剪切系数gs。将计算结果与已有文献结果及工程监测数据进行对比，深入分析了迭代求解k、gs值的Pasternak模型与传统模型的计算差异，并进一步研究了土中剪力、管道与隧道的夹角、土体弹性模量及隧道半径的变化对管-土相互作用的影响。研究结果表明：迭代求解的k、gs值能提升Pasternak模型的精确度；土中剪力对管道竖向位移计算值的影响可达15.3%；随着管道与隧道夹角的减小，管道的竖向位移增大、弯矩减小；土体弹性模量与隧道半径的增大均会增加管道的竖向位移和弯矩。  相似文献