一种横观各向同性岩体蠕变模型     

李列列  管俊峰  肖明砾  刘海朝  唐克东 《岩土力学》2020,41(9):2922-2930

层状岩体由于层理面或者结构面的存在，在力学上具有横观各向同性的特点，现有的各向同性蠕变模型难以全面反映横观各向同性岩体的蠕变力学特性。为构建能够反映横观各向同性岩体的三维蠕变模型，以能反映瞬时应变、减速蠕变和稳态蠕变特征的黏弹性Burgers模型为基础，基于常泊松比假定，在三维各向同性蠕变本构方程的基础上，按照算子替换的方法，将横观各向同性柔度矩阵代替各向同性柔度矩阵，并考虑了平行和垂直层理方向岩体蠕变力学行为的差异性，推导了横观各向同性岩体的三维蠕变本构方程。根据本构方程的特点，提出了根据平行和垂直方向岩体蠕变试验结果进行三维蠕变本构模型中蠕变参数的辨识方法。将提出的模型应用于三轴蠕变试验参数辨识，从而获得了一套完整的三维蠕变参数，并与试验结果进行对比分析，从而验证了所提模型与方法的合理性和有效性。进一步，指出了传统蠕变试验设计方案的局限性，给出了横观各向同性材料蠕变试验设计建议。研究成果为研究岩体三维蠕变机制提供了新思路，可对岩体蠕变试验设计提供相应的科研支撑。  相似文献   

辽东铀成矿带连山关地区韧性剪切带与铀成矿作用     

吴迪  刘永江  李伟民  常瑞虹 《岩石学报》2020,36(8):2571-2588

连山关地区位于华北克拉通北缘铀成矿省辽东铀成矿带，已知铀矿床（点）均发育在韧性剪切带附近。为了解韧性剪切带运动学、几何学构造变形机制及与铀矿的关系，本文以连山关岩体周缘韧性剪切带为研究对象，通过野外宏观调查和室内微观研究相结合的研究方法，探讨构造变形期次、韧性剪切带形成机理及其对铀成矿的控制作用。研究表明：连山关岩体周缘发育的韧性剪切带与近南北向挤压构造变形有关，其右行韧性剪切带应变类型为压扁应变，属于一般压缩-平面应变范围，Flinn指数K值在0.19~0.69之间，岩石类型属于S/SL型构造岩。研究区内铀矿体均为隐伏盲矿体，主要赋存于沿着连山关岩体和辽河群接触带右行剪切作用形成的背斜褶皱核部，和北东东向断裂关系密切。综合分析认为，连山关岩体南缘北西向韧性剪切带为一级控矿构造，是区内铀矿热液运移的通道，而剪切带边部的晚期北东东向断裂则是铀矿储存空间；铀源可能来自于太古宙古风化壳，并在大型韧性剪切活动（提供热液运移通道）和基性脉岩侵入（提供热源和还原剂）等综合因素作用下运移、富集成矿。  相似文献   

Variation in the vertical zonality of erodibility and critical shear stress of rill erosion in China's Hengduan Mountains     

Zhengan Su  Donghong Xiong  Jianhui Zhang  Tao Zhou  Hongkun Yang  Yifan Dong  Haidong Fang  Liangtao Shi 《地球表面变化过程与地形》2019,44(1):88-97

Soil erodibility is an essential parameter used in soil erosion prediction. This study selected the Liangshan town watershed to quantify variation in the vertical zonality of rill erodibility (k_r) in China's ecologically fragile Hengduan Mountains. Soil types comprised of yellow–brown (soil A), purple (soil B), and dry-red (soil C) in a descending order of occurrence from the summit to the valley, which roughly corresponds to the vertical climate zone (i.e. cool-high mountain, warm-low mountain, and dry-hot valley sections) of the study area. With elevation, vertical soil zonality varied in both soil organic matter (SOM) content and soil particle-size fractions. A series of rill erosion-based scour experiments were conducted, using water discharge rates of 100, 200, 300, 400, 500, and 600 mL min^-1. Additionally, detachment rates (Dr) were measured under three hydrological conditions (the drainage, saturation, and seepage treatments). Results show that both Dr and flow shear stress (Ʈ) values increased as discharge increased. As elevation increased, the k_r values decreased, while the vertical zonality of critical shear stress (Ʈ_c) values showed no obvious variation. The highest k_r values were observed during the seepage treatment, followed by the saturation treatment then drainage treatment, indicating that variation in vertical hydraulic gradients could significantly alter k_r values. This study also found that land-use types could also alter k_r and Ʈ_c values. Further research, however, is necessary to better quantify the effects of subsurface hydrological conditions and land-use types on k_r under different soil zonalities in China's Hengduan Mountains. © 2018 John Wiley & Sons, Ltd.  相似文献   

冻融循环下花岗岩剪切蠕变试验与模型研究     

张峰瑞  姜谙男  杨秀荣  申发义 《岩土力学》2020,41(2):509-519

为探讨冻融对寒区工程岩石剪切蠕变特性的影响，以吉林省辉白隧道花岗岩为研究对象，对经历不同冻融循环次数的试样开展细观特征分析和剪切蠕变试验。试验结果表明：（1）随着冻融次数的增加，试样裂隙、孔隙不断扩展，岩石表面损伤现象愈发明显；（2）试样主要以中小孔隙为主，孔隙度随着冻融次数的增加呈非线性增长趋势；（3）随着冻融循环次数增加，蠕变变形量和蠕变速率逐渐增大，而蠕变时长、破坏应力和长期强度均呈现明显降低趋势。根据试验结果，进行冻融岩石非定常蠕变参数的表达，提出了冻融岩石损伤黏性元件，构建了花岗岩冻融剪切蠕变本构模型。将蠕变试验曲线和理论模型拟合曲线进行对比，验证了模型的正确性和适用性。通过对蠕变参数进行敏感性分析，研究了其对花岗岩蠕变变形的影响，并给出了蠕变参数随冻融循环次数的变化规律。该研究结果对于寒区岩体工程长期稳定性评价具有指导意义。  相似文献   

Integration schemes with substepping algorithms for creep analysis in geomaterials     

Roberto Quevedo  Pedro Firme  Deane Roehl 《国际地质力学数值与分析法杂志》2019,43(7):1467-1487

This paper describes a robust and efficient methodology for predicting displacements, deformations, and stresses in geomaterials that are susceptible to creep. The methodology is based on two integration schemes, which consider substepping algorithms. The first scheme is used for integrating space-time relations in a global sense, whereas the second scheme is used for integrating stress-stain relations in a local sense. Different from previous studies, both integration schemes are easy to implement and general in the sense that they can be applied to any type of creep law. Through an in-house finite element simulator, several numerical tests are performed. They include triaxial and wellbore closure analyses considering soft soils and salt rocks. The results show that the combination of both schemes leads to stable and accurate solutions with reduced computational time.  相似文献   

塑性极限分析鱼雷锚锚尖贯入阻力     

瑜璐  杨庆  杨钢  张金利 《岩土力学》2020,41(6):1953-1962

鱼雷锚安装过程中,锚尖形状影响尖部贯入阻力进而影响贯入深度。基于塑性极限分析理论下限法分析不同锚尖长径比x的椭圆形锚尖的贯入阻力和贯入阻力系数,并考虑了贯入深度、锚-土界面摩擦对贯入阻力以及贯入阻力系数的影响。结果表明:(1)锚-土界面光滑时,锚尖贯入阻力系数随着锚尖长径比的增大而减小;锚-土界面粗糙时,锚尖贯入阻力系数随着锚尖长径比的增大而增大。(2)摩擦力对贯入阻力系数的影响随着ξ增大而增大。(3)随着埋置深度增加,贯入阻力系数受x影响最小时所对应的摩擦系数逐渐减小。(4)当锚-土界面摩擦系数ω 0.75时,工程中可选用ξ1的锚尖用以减小端部贯入阻力;当ω0.26时,ξ1的锚尖提供更小的端部贯入阻力。锚尖长径比ξ=0和ξ=1的下限解与前人研究的桩基和圆形结构的理论解较为一致,进一步验证了所提出的椭圆形锚尖下限法模型的可行性。  相似文献   

硅灰加固宁波软土的试验研究     

王泽平  王常明  江南  张在恒 《岩土工程技术》2020,(2):111-116,121

为探索硅灰对软土的力学性质的影响,以宁波鄞州地区一种淤泥质黏土为试样,掺入不同量的硅灰,对硅灰加固土的力学性质和结构特征进行了测试。采用三轴不固结不排水剪切试验,测试分析了不同掺入量的硅灰加固土的应力应变关系,通过扫描电镜SEM照片分析了不同硅灰掺入量的硅灰加固土的结构特征。结果表明:(1)硅灰可以提高软土的黏聚力,黏聚力随着硅灰掺入量的增加而增大;(2)随着硅灰掺入量的增加,硅灰加固土的抗变形能力呈先增加后减小的趋势;(3)同一围压条件下,随着硅灰掺入量的增加,硅灰加固土的破坏偏应力逐渐增加;(4)随着硅灰掺入量的增加,硅灰加固土中大孔隙逐渐减少,小孔隙逐渐数量增加,孔径<1μm的小孔隙组分逐渐占优。  相似文献   

The recognition of former melt flux through high‐strain zones          下载免费PDF全文

Catherine A. Stuart  Sandra Piazolo  Nathan R. Daczko 《Journal of Metamorphic Geology》2018,36(8):1049-1069

High‐strain zones are potential pathways of melt migration through the crust. However, the identification of melt‐present high‐strain deformation is commonly limited to cases where the interpreted volume of melt “frozen” within the high‐strain zone is high (>10%). In this contribution, we examine high‐strain zones in the Pembroke Granulite, an otherwise low‐strain outcrop of volcanic arc lower crust exposed in Fiordland, New Zealand. These high‐strain zones display compositional layering, flaser‐shaped mineral grains, and closely spaced foliation planes indicative of high‐strain deformation. Asymmetric leucosome surrounding peritectic garnet grains suggest deformation was synchronous with minor amounts of in situ partial melting. High‐strain zones lack typical mylonite microstructures and instead display typical equilibrium microstructures, such as straight grain boundaries, 120° triple junctions, and subhedral grain shapes. We identify five key microstructures indicative of the former presence of melt within the high‐strain zones: (a) small dihedral angles of interstitial phases; (b) elongate interstitial grains; (c) small aggregates of quartz grains with xenomorphic plagioclase grains connected in three dimensions; (d) fine‐grained, K‐feldspar bearing, multiphase aggregates with or without augite rims; and (e) mm‐ to cm‐scale felsic dykelets. Preservation of key microstructures indicates that deformation ceased as conditions crossed the solidus, breaking the positive feedback loop between deformation and the presence of melt. We propose that microstructures indicative of the former presence of melt, such as the five identified above, may be used as a tool for recognising rocks formed during melt‐present high‐strain deformation where low (<5%) volumes of leucosome are “frozen” within the high‐strain zone.  相似文献   

Effect of sand on the vacuum consolidation of dredged slurry     

Jun Wang  Yuanqiang Cai  Xueyu Geng  Fengqi Xu 《Marine Georesources & Geotechnology》2018,36(2):238-244

Vacuum preloading is often used to improve the geotechnical properties of dredged slurry. Although the performance of this method has improved with rapidly developing technology, soil columns usually formed on the drainage boundary induce the decrease of permeability around the boundary, thereby limiting the further development of this method. To address this issue, this paper proposes a method for pretreating the slurry combined with sand prior to vacuum consolidation. This method partially replaces the fine particles with sand to reduce the formation of soil columns. Two groups of vacuum preloading tests were performed to investigate the effect of sand content and sand grain size on the vacuum consolidation of dredged slurry. The test results revealed that for a given sand grain size, increasing the sand content of the sand–slurry mixture increased the pore water drainage and accelerated the dissipation of pore water pressure, thereby increasing the vane shear strength. In contrast, for a constant sand content, the samples containing coarse sand exhibited increased pore water drainage and accelerated dissipation of pore water pressure, thereby increasing the vane shear strength of the soil.  相似文献   

珠江三角洲海相沉积软土压缩和剪切变形特性试验研究   总被引：3，自引：0，他引：3       下载免费PDF全文

张岩  耿济世  毛磊  刘芙荣 《地震工程学报》2018,40(4):745-751

为了研究近代海相沉积软土的变形特征,本文对珠江三角洲河口地区的全新世海相沉积的软土进行了室内单轴压缩与不同围压下作用下的三轴固结不排水(CU)、不固结不排水(UU)的剪切试验。试验结果表明:原状土和重塑土样的孔隙比随压力的增大而下降,且与加压方式有密切关系,加压幅度越小,土的扰动破坏越小;原状土样固结系数随着压力增加而递减,整体近似符合指数函数分布,重塑土样固结系数随着压力增加逐渐增大,整体近似符合线性函数分布。在相同的固结压力下,原状土样的强度低于重塑土样的强度。土样的应力应变曲线为应变硬化型,且围压对重塑土的影响小于原状土。  相似文献