Three-dimensional active earth pressure from cohesive backfills with tensile strength cutoff     

Zheng-Wei Li  Tian-Zheng Li  Xiao-Li Yang 《国际地质力学数值与分析法杂志》2020,44(7):942-961

Most of previous analyses on the active earth pressure were performed in two-dimensional cases using the Mohr-Coulomb (M-C) failure function to describe the soil strength. However, all failures of retained slopes indicate a somewhat three-dimensional (3D) feature, and the M-C function is found to overestimate the tensile strength of cohesive soil. In this work, a kinematic limit analysis–based approach is developed for computing the 3D active earth pressure resulting from cohesive backfills. The concept of tensile strength cutoff is adopted to implement the reduction or elimination of tensile strength from the strength envelope. An extended 3D horn failure mechanism that is associated with the modified strength envelope is developed to characterize the collapse of retained slopes. The resultant of active earth pressure is evaluated from the work rate balance equation and expressed as an unfactored coefficient. The obtained results indicate that less support provided by the wall is required when allowing the existence of soil cohesion and 3D effects and that eliminating the tensile strength can observably increase the active earth pressure, especially for the backfill with a great level of cohesion.  相似文献   

Reliability of mooring lines and piles for a permanently manned vessel in a tropical cyclone environment     

《Applied Ocean Research》2019

The factors of safety for stationkeeping systems in current standards (ISO, API) are not derived or validated using reliability analyses. As the oil and gas exploration and production is breaking new boundaries, deploying new floating systems and moving into regions with harsher environments, it is of paramount importance to understand what level of reliability these new marine structures are achieving. This paper presents a reliability analysis of the mooring system of a Floating LNG (FLNG) vessel permanently moored and permanently manned offshore North West Australia in a tropical cyclone environment. The reliability analysis addresses both the mooring chain and the pile foundation. The analysis accounts for the long term characteristics of the environment, including the short term variability, in response to a given sea state and the variability and uncertainty in strength of the mooring chain and the pile. The stationkeeping system was analysed using detailed time domain simulations, capturing system non-linearities and low frequency oscillations as well as wave frequency responses and, thereby, reducing modelling uncertainties to a minimum.It is found that for the conditions modelled, neither the chain nor the pile meet a target reliability of 10⁻⁴/annum using the factors of safety commonly used in design following current ISO and API standards. New factors of safety are proposed to achieve this target reliability. For the pile design, one complicating factor is that current design standards do not explicitly define the exceedance probability that should be associated with the characteristic value of the undrained shear strength to be used in the design. It is demonstrated that the required factor of safety is crucially dependent on the definition of this characteristic value and on the level and the type of uncertainty in the soil strength profile. A recommendation is made regarding the definition of this characteristic value and the associated factor of safety. Furthermore, it is found that designing the mooring system to an environmental condition with a return period of 10,000 yr (as an Abnormal Limit State event), and setting the factor of safety to unity, meets the target reliability of 10⁻⁴/annum for the pile, if the characteristic undrained shear strength is a lower bound, defined in this paper by the 10th percentile value. For the chain however, this target reliability is not achieved.  相似文献   

Development of partial factor design method on bending strength of piles for Japanese Specifications for Highway Bridges     

Toshiaki Nanazawa  Tetsuya Kouno  Gaku Sakashita  Takashi Nakaura 《Georisk: Assessment and Management of Risk for Engineered Systems and Geohazards》2019,13(3):176-184

ABSTRACT

This paper describes the development of a partial factor design method on the bending strength of piles for the Japanese Specifications for Highway Bridges. First, uncertainties in mobilised bending moments and yield bending moments were evaluated by Monte Carlo simulations. Second, the reliability of piles designed by the previous specifications were evaluated on the basis of reliability analysis considering uncertainties in the mobilised bending moments, yield bending moments, and other factors. Finally, a partial factor design method utilising a survey subsurface investigation method and ground type was developed to reach target reliability levels determined by the Standards.  相似文献   

细粒含量对冰碛土抗剪强度影响的实验研究   总被引：1，自引：1，他引：0  

蒋德旺  崔鹏  王姣  李战鲁  殷延洲  雷鸣宇 《冰川冻土》2019,41(1):129-139

为研究细粒组颗粒在浸水/降雨条件下产生迁移对冰碛土抗剪强度的影响，从西藏林芝市帕隆藏布嘎隆寺沟流域内采取冰碛土样品，进行7种不同细粒（粒径小于2 mm）含量情况下的冰碛土比重和相对密度的测试，开展了不同围压下的大型饱和固结不排水三轴（CU）实验。结果表明：（1）细粒含量对干密度的影响较小，不同细粒含量的冰碛土孔隙比大致相同，细颗粒对孔隙具有改造作用，不同细粒含量会引起孔隙结构的差异，从而导致冰碛土的结构差异，最终导致抗剪强度的不同；（2）细颗粒迁移导致冰碛堤坡脚和内部一定深度细粒含量较高，达到一定的量值时，抗剪强度明显降低，冰碛堤容易发生剪切破坏；（3）细粒含量对抗剪强度参数的变化具有重要影响，从中还可以反映出冰碛土结构控制的变化：粗颗粒控制→粗细颗粒共同控制→细颗粒控制。研究结果对于评价冰碛堤的稳定性具有重要意义。  相似文献   

地幔热导率的选取对动力学数值模拟的影响——以岩石圈张裂过程为例          下载免费PDF全文

谌永强  施小斌  廖杰  许鹤华  任自强 《地球物理学报》2020,63(5):1998-2012

目前存在有多种地幔热导率模型,不同模型在数值和随温压变化的特征上有明显的差异.为探究不同热导率模型对动力学数值模拟结果的影响,本文对不同模型下的岩石圈张裂过程进行模拟研究,探讨地幔热导率对岩石圈热传输、变形和熔融过程的影响及其作用机理.结果显示,不同热导率模型下,岩石圈的变形和熔融特征表现出明显差异.高热导率模型下,岩石圈破裂较晚,形成陆缘较为宽阔,地壳熔融强烈而地幔熔融较弱;低热导率模型下,岩石圈破裂较早,形成陆缘较为狭窄,地幔熔融强烈而地壳熔融较弱.这种差异源于不同地幔热导率下岩石圈和地幔热状态的变化及相应力学性质的改变.高热导率下,热传导的增温效应显著,岩石圈呈现较热的状态,其强度整体较低,壳幔耦合减弱;而低热导率下,热对流的增温效应显著,岩石圈呈较冷的状态,其强度整体较高,壳幔耦合增强.基于模拟结果,本文认为地幔热导率的选取对动力学模拟的结果有着较为显著的影响,相对于随温压的变化,热导率数值的差异对动力学数值模拟的结果影响更大,尤其是对于地幔熔融过程的影响.  相似文献   

Dynamic characteristics of marine soft clay under variable phase difference and initial static shear stress     

Wenqian Dong  Xiuqing Hu  Hongtao Fu 《Marine Georesources & Geotechnology》2020,38(7):770-785

Abstract

Under seismic loading, the soil layer is subjected to multidirectional cyclic shear stress with different amplitudes and frequencies because of the coupling of multiple shear waves and the soil element within a slope or behind a retaining wall is subjected to initial static shear stress before subjected to cyclic loading. Due to the complexity of seismic loading propagation, a phase difference exists between the initial static shear stress and cyclic shear stress. To investigate the influence of the phase difference and initial static shear stress on cyclic shear strain, cyclic modulus, and cyclic strength, a series of laboratory tests are performed on Wenzhou marine soft clay by multi-directional simple shear system, which can simulate the actual state better by controlling the horizontal cyclic stress in the x and y directions simultaneously. As the phase difference varies from 0° to 90°, the dynamic shear modulus increases and cyclic strain accumulation decreases with an increasing number of cycles. The shear strain increases with the initial shear stress.  相似文献   

花岗岩残积土动态冲击性能的SHPB试验研究     

刘新宇  张先伟  岳好真  孔令伟  徐超 《岩土力学》2020,41(6):2001-2008

为研究花岗岩残积土的动态冲击性能，开展了高速冲击下的分离式霍普金森压杆（SHPB）试验，与常规应变率下的试验结果比较，分析了高应变率对花岗岩残积土的应力?应变特性和强度的影响。结果表明：低、高应变率下的花岗岩残积土的?-?a（轴向应力?轴向应变）曲线均呈现出软化型。随着应变率 增加，?-?a曲线向?a增大的方向移动，破坏应变?af增加。但高应变率下?af增加的程度更加明显。花岗岩残积土的峰值强度普遍具有应变率依赖性，二者可用直线关系拟合，但低、高应变率下的拟合关系并不一致。提出了率敏性因子m定量评价依赖性强弱。研究发现，随着应变率的提高，强度的应变率依赖性减弱，低应变率下的m为26.694，而高应变率下仅为0.013。相关试验结果指出，高速冲击荷载对土体总体有害。工程中应该采取合理措施控制冲击荷载的危害。该研究有助于深化花岗岩残积土动态冲击性能的理解，为相关工程的施工与设计提供技术参考。  相似文献   

Undrained lower bound solutions for end bearing capacity of shallow circular piles in non-homogeneous and anisotropic clays     

Boonchai Ukritchon  Suraparb Keawsawasvong 《国际地质力学数值与分析法杂志》2020,44(5):596-632

The undrained bearing capacity of shallow circular piles in non-homogeneous and anisotropic clay is investigated by the lower bound (LB) finite element limit analysis (FELA) under two-dimensional (2D) axisymmetric condition using second-order cone programming, and the new solution of the problem is presented. Modified from the isotropic von Mises yield criterion, a cross-anisotropic undrained strength criterion of clays under the axisymmetric state of stress requiring three input shear strengths in triaxial compression, direct simple shear, and triaxial extension is employed in the 2D axisymmetric LB FELA. Parametric studies on the effects of pile embedment ratio, dimensionless strength gradient, anisotropic strength ratio, and pile roughness are investigated extensively, while the predicted failure mechanisms associated with these parameters are discussed and compared. Numerical results of undrained end bearing capacity of shallow circular piles are summarized in the form of design tables that are useful for design practice and represent a new contribution to the field of pile capacity considering the combined effects of undrained strength non-homogeneity and anisotropy.  相似文献   

袋装石土工袋剪切力学特性试验研究     

樊科伟  刘斯宏  廖洁  方斌昕  王建磊 《岩土力学》2020,41(2):477-484

袋装石土工袋堆叠过程中在土工袋接触面形成的咬合和嵌固作用，对土工袋剪切力学强度和破坏形式有较大的影响。通过一系列直剪试验研究了咬合和嵌固作用的影响，试验结果表明：袋装石土工袋层间咬合和嵌固作用能够增大土工袋抗剪强度；咬合作用随着土工袋上部竖向应力的增大有所减小，而嵌固作用则有所增大；袋装石土工袋在剪切过程中会产生两种破坏形式，分别为土工袋袋体自身变形和层间滑动破坏；土工袋组合体在受到水平剪切力时会发生整体变形，随后在组合体内部产生阶梯型滑动面，滑裂面的形状随着竖向荷载的增大而有所不同，相应的抗剪强度也会随着滑动面的改变而变化。  相似文献   

塑性极限分析鱼雷锚锚尖贯入阻力     

瑜璐  杨庆  杨钢  张金利 《岩土力学》2020,41(6):1953-1962

鱼雷锚安装过程中,锚尖形状影响尖部贯入阻力进而影响贯入深度。基于塑性极限分析理论下限法分析不同锚尖长径比x的椭圆形锚尖的贯入阻力和贯入阻力系数,并考虑了贯入深度、锚-土界面摩擦对贯入阻力以及贯入阻力系数的影响。结果表明:(1)锚-土界面光滑时,锚尖贯入阻力系数随着锚尖长径比的增大而减小;锚-土界面粗糙时,锚尖贯入阻力系数随着锚尖长径比的增大而增大。(2)摩擦力对贯入阻力系数的影响随着ξ增大而增大。(3)随着埋置深度增加,贯入阻力系数受x影响最小时所对应的摩擦系数逐渐减小。(4)当锚-土界面摩擦系数ω 0.75时,工程中可选用ξ1的锚尖用以减小端部贯入阻力;当ω0.26时,ξ1的锚尖提供更小的端部贯入阻力。锚尖长径比ξ=0和ξ=1的下限解与前人研究的桩基和圆形结构的理论解较为一致,进一步验证了所提出的椭圆形锚尖下限法模型的可行性。  相似文献