考虑冲刷影响的筒型基础竖向极限承载力研究     

陆罗观  刘润  练继建  陈广思 《海洋工程》2019,37(3):69-77

大直径宽浅式筒型基础,阻水宽度大,在位工作期间受波浪海流作用,其周围土体易被冲刷。为研究单侧地基土体受冲刷后筒型基础的竖向极限承载力变化,通过引进冲刷率的概念,采用有限元方法研究了不同冲刷率下筒型基础的竖向极限承载力;并基于Meyerhof理论建立了计算不同冲刷率下筒型基础竖向极限承载力的极限平衡方法。研究结果表明,随着冲刷率增大,筒型基础的极限承载力出现不同程度的下降,当冲刷率为0.8时,即筒型基础单侧土体冲刷深度达6.4 m时,筒型基础的竖向极限承载力折减率为3.28%。建立的极限平衡算法可准确计算冲刷条件下筒型基础的竖向极限承载力。  相似文献   

黄海透光层悬浮半导体矿物组成及其促进微生物胞外电子传递过程初探     

刘佳  孙元  任桂平  鲁安怀  李艳  丁竑瑞 《岩石矿物学杂志》2020,39(1):96-104

在地球上最为活跃的海洋透光层体系中,矿物-微生物交互作用的形式十分丰富。系统采集了黄海近海透光层水体样品,测试分析发现其中分布大量悬浮半导体矿物及微生物群落。通过电感耦合等离子质谱仪(ICP-MS)、环境扫描电子显微镜(ESEM)及配有的EDX能谱仪,从宏观到微区对悬浮颗粒矿物的化学元素组成进行了测试分析,发现其主要矿物组成元素为Si、O、Na、K、Ca、Al等,且含有较高含量的Mn、Fe、Ti等金属元素;通过X射线衍射光谱(XRD)、拉曼光谱(Raman)测试从整体到局部分析悬浮颗粒矿物的物相组成,发现其主要组成矿物为石英、钠长石、方解石、云母和绿泥石等,还有锐钛矿、金红石、板钛矿、针铁矿等铁、钛金属氧化物半导体矿物。通过16S rRNA高通量测序分析海水中主要微生物群落为Proteobacteria、Actinobacteria、Bacteroidetes、Planctomycetes、Woeseia、Fluviicola等,并通过构建双室反应体系对海水微生物与悬浮矿物间氧化还原作用及胞外电子传递过程进行了表征,结果显示增加海水悬浮矿物作为电子受体后,体系开路电压由330. 80 mV提升至426. 59 mV,提升比率达130%,最大输出功率由8. 376 9 mW/m^2提升至12. 096 8 mW/m^2,为原体系的1. 44倍。实验研究表明,海水透光层悬浮矿物能有效参与并促进微生物胞外电子传递过程,为后续深入研究基于电子能量传递利用的半导体矿物-微生物协同作用以及元素循环调控机制奠定初步基础。  相似文献   

多元素衬值累加地球化学方法在找矿中的应用——以青海省夏日哈-什多龙远景区为例     

赵志飞 《地质与勘探》2020,56(2):328-336

青海省夏日哈-什多龙成矿远景区位于青藏高原东昆仑东段,西起都兰县夏日哈镇,东至兴海县什多龙一带,跨祁漫塔格北坡-夏日哈岩浆弧和北昆仑岩浆弧,是青海省重要的成矿区。为了在该区寻找新的成矿有利地段,本文在对该区区域地质背景、矿产特征及区内典型矿床地质特征系统研究的基础上,利用多元素衬值累加地球化学找矿方法,在区域上优选出一批找矿靶区。多元素衬值累加地球化学找矿方法首先收集远景区1∶5万水系沉积物测量成果,经过数据处理,绘制远景区衬值累计地球化学图,进而建立典型矿床找矿模式,最终通过对比分析,选出新的找矿靶区。对圈定的找矿靶区进行野外踏勘检查,均发现不同程度的矿化线索,为今后在该区进一步找矿起到了很好的指导作用。通过本次工作,发现了该方法在靶区圈定方面的优势:(1)可快速圈定异常,提高工作效率;(2)编制的地球化学图浓集中心更显著;(3)圈定的找矿靶区找矿成果显著,尤其针对陆相火山岩型多金属矿、斑岩型铜钼矿、矽卡岩型多金属矿找矿成果突出;(4)能直观反映背景变化趋势,有助于评价异常。  相似文献   

贵州苗匡热矿水地热区水化学特征及热储条件分析     

杨晓飞 《地质与勘探》2020,56(1):94-101

贵州苗匡热矿水地热区大地构造位于江南复合造山黔南坳陷铜仁复式褶皱变形带,区域构造为红石古断裂带与苗匡断裂交汇锐角区,区内出露的地层有前南华系板溪群、南华系、震旦系、寒武系;热矿水水化学类型为HCO_3-Na型,含高氟、锶、锂、偏硅酸;弱碱性水;呈带状中低温热储;区域大地热流供给热量;地下热矿水补给为构造破碎带深远程补给;区域性红石活动断裂带具有导热导水储水性,热矿水被温差、压力差等驱动循环运移至断裂破碎带富集,苗匡次级断裂带在该热储起到连通传导作用;热矿水井口温度45℃,出水量560 m~3/d。研究结果可对该区热矿水勘查开发及利用提供参考和借鉴。  相似文献   

Climatic signals in lacustrine deposits of the Upper Yacoraite Formation,Western Argentina: Evidence from clay minerals,analcime, dolomite and fibrous calcite     

João Paulo B. Gomes  Rodrigo B. Bunevich  Sandra N. Tonietto  Daisy B. Alves  Julice F. Santos  Fiona F. Whitaker 《Sedimentology》2020,67(5):2282-2309

Authigenic clays are an important control on reservoir quality in lacustrine carbonates but remain challenging to predict. Lacustrine depositional systems respond to climatic variations in rainfall, surface runoff and groundwater input, and evaporation, and result in rapid and frequent changes in lake volume; this is expressed through changing water depth and shoreline position. In the upper portion of the Early Palaeocene Yacoraite Formation of the Salta Basin in Argentina, extensive lacustrine deposits were deposited during the sag phase of rifting. Prior high-resolution stratigraphic studies have suggested that climatic factors control microbial carbonate sequences within a ‘balanced fill’ lake, with variation in the lake level having a major influence on facies association changes. This study characterizes the evolution of facies and mineralogy within the Yacoraite Formation, focusing on the distribution of clay minerals, making a link between the high, medium and low-frequency sequence stratigraphic cycles. The low-frequency transgressive hemicycle of the upper portion of the Yacoraite Formation is comprised of abundant siliciclastic facies, suggesting a wetter period. Microbialites occurring in this interval are coarse-grained and agglutinated. Detrital clay minerals such as illite and chlorite and associated siliciclastic sediments were input to the lake during high-frequency transgressive periods. During high-frequency regressive hemicycles, sedimentation was dominated by carbonate facies with Ca-rich dolomite and the authigenic clays are comprised of chlorite/smectite mixed-layers. By contrast, the low frequency regressive hemicycle records fine-grained agglutinated microbialite with horizons of fibrous calcite, more stoichiometric dolomite, barite and authigenic magnesian smectite. This indicates elevated ion concentrations in the lake under intense evaporation during an arid period. Understanding the conditions that are favourable for formation and preservation of authigenic clays within the lacustrine environment can improve understanding of reservoir quality in comparable economically important deposits.  相似文献   

Kainsaz(CO3)陨石中两个富Al球粒的氧同位素组成特征与形成演化     

戴德求  包海梅  刘爽  尹锋 《岩石学报》2020,36(6):1850-1856

富Al球粒是原始球粒陨石中一种矿物岩石学特征介于富钙铝包体(CAIs)和镁铁质硅酸盐球粒之间的特殊集合体,所以常常认为富Al球粒在认识CAIs和镁铁质硅酸盐球粒形成演化过程中的相互联系具有特殊意义。然而,对富Al球粒的初始物质组成以及形成演化过程一直存在较多争议,而氧同位素组成研究能够对球粒演化和早期星云环境等提供重要的信息。在本文中我们报导了来自Kainsaz(1937年降落于俄罗斯,CO3型)碳质球粒陨石中的2个富Al球粒(编号K1-CH1和K2-CH2)的矿物岩石学和氧同位素组成特征。K1-CH1的矿物组成主要为橄榄石、低钙辉石和富钙长石,K2-CH2为橄榄石和富钙长石。2个球粒中的矿物均具有贫~(16)O同位素组成特征。K1-CH1中矿物的△~(17)O组成基本上位于2个区间:-11.1‰～-8.7‰和-3.9‰～0.4‰;而K2-CH2的△~(17)O介于-6.6‰～-0.6‰之间,且具有从中部至边部升高的趋势。矿物岩石学和氧同位素特征表明,这2个富Al球粒的初始物质组成为富CAIs和镁铁质硅酸盐。在球粒熔融结晶过程中,与贫~(16)O同位素组成(△~(17)O:-8.7‰～-7.8‰)的星云发生了氧同位素交换。球粒形成后,发生迁移进入陨石母体,在相对更贫~(16)O同位素组成(△~(17)O:-0.6‰～0.4‰)的母体中(流体参与)发生变质作用,并再次发生了氧同位素交换。  相似文献   

A finite element approach for predicting the full resistance profile of a spudcan deeply penetrating in dense sand overlying clay     

《Applied Ocean Research》2019

This paper presents a finite element approach to calculate the full resistance profile of a spudcan deeply penetrating in dense sand overlying clay, in which a potential for an installing spudcan to experience a sudden uncontrolled punch-through failure exists. A modified Mohr-Coulomb model characterized by incorporating a four-phase variation of the mobilized strength and dilation parameters with an equivalent accumulated plastic strain is developed and tested for the overlying dense silica sand. An extended Tresca model is used for the strain softening of the underlying clay. A series of large deformation finite-element (LDFE) analyses are carried out, varying the strength and dilation parameters as well as the spudcan geometries. A fairly good performance of the present approach is verified by validating against groups of centrifuge tests data, allowing the numerical study to be extended parametrically. The four-phase variation of the mobilized strength and dilation parameters involved in the progressive failure of the upper dense sand is parametrically studied and extended to cover the range of sand relative densities that are of practical interest. Additionally, comparisons with the typical existing LDFE analyses using both simple and sophisticated constitutive models are carried out. It shows that the present approach performs fairly well to calculate the full resistance profile of a spudcan deeply penetration in both thin and thick dense sand overlying clay, especially the peak and post-peak resistance, within around 5% of the corresponding centrifuge tests results.  相似文献   

Dynamic characteristics of marine soft clay under variable phase difference and initial static shear stress     

Wenqian Dong  Xiuqing Hu  Hongtao Fu 《Marine Georesources & Geotechnology》2020,38(7):770-785

Abstract

Under seismic loading, the soil layer is subjected to multidirectional cyclic shear stress with different amplitudes and frequencies because of the coupling of multiple shear waves and the soil element within a slope or behind a retaining wall is subjected to initial static shear stress before subjected to cyclic loading. Due to the complexity of seismic loading propagation, a phase difference exists between the initial static shear stress and cyclic shear stress. To investigate the influence of the phase difference and initial static shear stress on cyclic shear strain, cyclic modulus, and cyclic strength, a series of laboratory tests are performed on Wenzhou marine soft clay by multi-directional simple shear system, which can simulate the actual state better by controlling the horizontal cyclic stress in the x and y directions simultaneously. As the phase difference varies from 0° to 90°, the dynamic shear modulus increases and cyclic strain accumulation decreases with an increasing number of cycles. The shear strain increases with the initial shear stress.  相似文献   

Undrained monotonic shear behavior of marine soft clay after long-term cyclic loading     

Lin Guo  Hongxu Jin  Li Shi 《Marine Georesources & Geotechnology》2020,38(7):854-866

Abstract

In the coastal area, nearshore and offshore structures have been or will be built in marine soft clay deposits that have experienced long-term cyclic loads. Therefore, the mechanical behavior of marine clay after long-term cyclic loading needs to be investigated. In this research, a series of monotonic and cyclic triaxial tests were carried out to investigate the postcyclic mechanical behavior of the marine soft clay. The postcyclic water pore pressure, shear strength and secant stiffness are discussed by comparing the results with the standard monotonic test (without cyclic loading). It is very interesting that the postcyclic behavior of marine soft clay specimen is similar to the behavior of overconsolidated specimen, that is, the specimen shows apparent overconsolidation behavior after long-term cyclic loading. Then relationship between the overconsolidation ratio and the apparent overconsolidation ratio is established on the basis of the theory of equivalent overconsolidation. Finally, a validation formula is proposed which can predict the postcyclic undrained shear strength of marine soft clay.  相似文献   

甘肃北山老金厂金矿床载金矿物特征、原位硫同位素组成及其对成矿的指示意义     

黄式庭  于晓飞  吕志成  刘家军  李永胜  杜泽忠  吕鑫  孙海瑞  杜轶伦 《吉林大学学报(地球科学版)》2020,50(5):1387-1403

老金厂金矿床是北山成矿南带最具代表性的中低温岩浆热液型金矿床之一，其规模为中型。依据脉体穿插、矿物共生组合和矿石结构构造等特征，将矿床矿化作用过程划分为石英-黄铁矿阶段（Ⅰ）、石英-含砷黄铁矿-毒砂阶段（Ⅱ）、石英-黄铁矿-多金属硫化物阶段（Ⅲ）和石英-方解石阶段（Ⅳ）。利用电子探针研究了不同成矿阶段载金矿物的元素组成及其分布规律。Ⅰ阶段：黄铁矿以粗粒自形立方体为主，粒度为0.50~1.50 mm，贫As、Au；毒砂含量极少，呈细粒他形。Ⅱ阶段：含砷黄铁矿周围常有大量毒砂产出，含砷黄铁矿多为立方体、五角十二面体，粒度为0.30~1.00 mm，富As、Au；该阶段矿化最为强烈，毒砂主要形成于此时期，多呈棱柱状、柱状、放射状集合体，显示富S亏As特征。Ⅲ阶段：多以黄铁矿-黄铜矿-闪锌矿共生组合脉的形式产出，黄铁矿多呈长条状，以富S、Cu、Zn、Au和贫Fe、As为特征。Ⅳ阶段：矿化作用极弱，毒砂、黄铁矿含量极少，为细粒他形。原位硫同位素组成显示：Ⅰ阶段黄铁矿δ³⁴S_V-CDT值为-3.8‰~-2.9‰，均值为-3.3‰；Ⅱ阶段黄铁矿和毒砂δ³⁴S_V-CDT值为-4.7‰~2.6‰，均值为-3.3‰；Ⅲ阶段黄铁矿和闪锌矿δ³⁴S_V-CDT值主要分布于-1.9‰~1.0‰之间，均值为0.1‰。此3个阶段硫同位素组成反映了成矿期硫主要来源于幔源岩浆，混入了部分地层硫。综合前人研究成果，认为成矿早期至晚期，成矿流体总体上由富S贫As向富As贫S演化。Ⅰ阶段体系处于中性稳定的环境，硫源充足；Ⅱ阶段为贫S富As的高氧逸度环境，由于大气降水对地层的淋滤渗透，混入富As流体，Au可能与As结合形成Au-As络合物，在成矿有利部位富集沉淀；Ⅲ阶段成矿元素种类丰富，体系为富S贫As的弱还原环境，Au很可能与HS^-、S^-形成络合物进入黄铁矿晶格。  相似文献