中-哈-吉-乌天山变形带容矿金矿床:成矿环境和控矿要素与找矿标志     

薛春纪  赵晓波  赵伟策  赵云  张国震  Bakhtiar NURTAEV  Nikolay PAK  莫宣学 《地学前缘》2020,27(2):294-319

天山是全球第二大金矿富集区,世界级和大型-超大型金矿床东西成带横贯中国新疆中部—哈萨克斯坦东南部—吉尔吉斯斯坦—乌兹别克斯坦,构成巨型跨境金成矿带。天山巨型跨境金成矿带和重要金矿床形成的地质环境、成矿的控制要素、找矿勘查的标志都是学术界和工业界高度关注的重大地质和找矿问题。通过广泛、深入地文献调研和境内外天山较全面野外地质矿产调查与研究,本文认为中-哈-吉-乌天山大规模金成矿主体形成于晚石炭世—早二叠世古亚洲洋闭合后的陆块拼贴变形过程,部分形成于中—晚二叠世陆内走滑变形过程。中天山南、北缘古缝合带及其附近的大型脆性/韧-脆性变形带是巨量金成矿的关键控制因素,多期叠加复合成矿是天山变形带容矿金矿床的显著特征。地壳初始富集、构造变形活化、岩浆热液叠加是天山变形带容矿金矿床的主控因素。“碳质细碎屑岩+脆韧性变形带+海西末期岩体”是中-哈-吉-乌天山变形带容矿大型-超大型金矿的找矿标志组合。  相似文献   

基于最大球算法定量表征土体空间孔隙网络     

解朝阳  张巍  姚东方  王坚  朱雨辰 《工程地质学报》2020,28(1):60-68

孔隙网络控制着土体渗流、排水固结与基质吸力等重要工程性质。本文介绍了多孔介质孔隙网络最大球建模基本原理与算法。以显微CT扫描振捣干法生成的南京粉砂试样为例,采用最大球算法建立了试样三维重构模型表征单元体(REV)的空间孔隙网络球棍模型,计算得到了样品REV尺度的孔隙网络参数,统计发现,孔隙半径、喉道半径、孔隙配位数、孔隙截面形状因子、喉道截面形状因子与喉道长度等孔隙参数均近似服从正态分布,孔隙体积近似服从衰减型指数分布。孔隙与喉道半径分别分布在100μm与65μm以内,两者数学期望分别为40. 0μm与18. 0μm;配位数分布在25以内,数学期望为5. 1;孔隙与喉道截面形状因子分别分布在0. 01~0. 04与0. 01~0. 05的区间内,两者数学期望分别为0. 019与0. 033;喉道长度分布在100~800μm以内,数学期望为292. 22μm。同时发现,样品中体积小于1. 5×10^7μm^3的小孔隙数量超过90%。本方法可应用于土体细观孔隙结构的定量表征。  相似文献   

Undrained lower bound solutions for end bearing capacity of shallow circular piles in non-homogeneous and anisotropic clays     

Boonchai Ukritchon  Suraparb Keawsawasvong 《国际地质力学数值与分析法杂志》2020,44(5):596-632

The undrained bearing capacity of shallow circular piles in non-homogeneous and anisotropic clay is investigated by the lower bound (LB) finite element limit analysis (FELA) under two-dimensional (2D) axisymmetric condition using second-order cone programming, and the new solution of the problem is presented. Modified from the isotropic von Mises yield criterion, a cross-anisotropic undrained strength criterion of clays under the axisymmetric state of stress requiring three input shear strengths in triaxial compression, direct simple shear, and triaxial extension is employed in the 2D axisymmetric LB FELA. Parametric studies on the effects of pile embedment ratio, dimensionless strength gradient, anisotropic strength ratio, and pile roughness are investigated extensively, while the predicted failure mechanisms associated with these parameters are discussed and compared. Numerical results of undrained end bearing capacity of shallow circular piles are summarized in the form of design tables that are useful for design practice and represent a new contribution to the field of pile capacity considering the combined effects of undrained strength non-homogeneity and anisotropy.  相似文献   

p-y曲线对成层土体中大直径单桩的适用性研究          下载免费PDF全文

孟晓伟  翟恩地  许成顺 《海洋技术学报》2019,38(2)

API规范推荐的p-y曲线是由均质土体得到的,并未考虑土层间相互作用,Georgiadis基于柔性桩提出了等效深度法修正p-y曲线,把均质土p-y曲线延伸到了成层土体中。为了研究p-y曲线和等效深度法对于大直径单桩在成层土体中的适用性,取4种典型地质条件:成层砂土、砂土-黏土-砂土、成层黏土和黏土-砂土-黏土,通过L-PILE软件计算了6 m直径单桩基础的p-y曲线、桩顶水平荷载-位移曲线、桩身位移和弯矩。并与ABAQUS建立的单桩基础三维有限元模型计算结果进行比较。结果表明等效深度法对于成层砂土影响不大;对于成层黏土影响较大;对于中间为软弱土层的成层土体,在荷载较大时影响显著,等效深度法计算结果更加接近FEM结果。在成层土体中,p-y曲线应用于大直径单桩对于砂土高估了初始刚度,低估了极限抗力;对于黏土则低估了初始刚度和极限抗力。  相似文献   

江西东坪石英脉型黑钨矿矿床地质特征、控矿因素及找矿标志     

杨细浩  胡文洁  钟起泓  朱昌杰  万欢  胡正华 《吉林大学学报(地球科学版)》2019,49(5):1301-1316

东坪钨矿床是近年在赣北地区新发现的首个超大型石英脉型黑钨矿矿床，位于长江中下游成矿带幕阜山地区东坪-香炉山钨矿找矿远景区东部。矿床赋矿层位为新元古代双桥山群安乐林组浅变质岩系，北东向断裂及其两侧的次级裂隙为区内主要控矿构造、容矿构造，隐伏的燕山晚期黑云母二长花岗岩为成矿岩体，与区内钨多金属成矿关系密切的为石英脉状硅化；两个矿带的钨矿体均产于成矿岩体外接触带，呈现了石英脉型黑钨矿矿床典型的"五层楼"分带特征，矿石工业类型主要为黑钨矿矿石；明确了构造和岩浆岩等主要控矿因素；总结出地表微细裂隙云英岩化-黄铁矿化蚀变带、含硫化物石英细脉带、石英脉、重砂及地球化学异常为区内主要找矿标志。  相似文献   

2016年夏季南海海盆水体颗粒物粒径分布特征*     

郑文迪  周雯  曹文熙  王桂芬  邓霖  徐文龙  许占堂  李彩  蔡建南 《热带海洋学报》2018,37(5):74-85

颗粒物粒径分布(Particle Size Distribution, PSD)代表了颗粒物浓度与颗粒物粒径之间的关系, 影响着海洋生态环境和水体光学特性等。文章基于2016年夏季航次调查的生物光学剖面数据, 研究了南海海盆海域PSD的分布特征。研究发现, 幂律函数可以较好地拟合南海海盆区域的PSD, 对数空间中的实测的PSD与模拟的PSD平均决定系数高达0.95。PSD斜率(ξ)的分布范围为[1.27, 7.65], 均值为3.93±0.56。南海海盆区域表层水体的ξ均值与全球大洋表层水体的ξ均值相近, 但高于海湾等表层水体的ξ均值。ξ能较好地表征颗粒物平均粒径D_A的大小, 两者存在明显负相关关系, 即ξ值越高, D_A越小; 反之, D_A越大。通过分析T1断面的生物光学剖面数据及总体平均的PSD剖面数据, 发现PSD剖面分布特征如下: 1)表层水体的ξ值相对较高, 且D_A值相对较低, 推测可能是由于微微型藻类为主导颗粒物所致; 2) ξ值极小值层出现在次表层叶绿素浓度极大值层(Subsurface Chlorophyll Maximum Layer, SCML)中, 并伴随D_A极大值层的出现, 其原因可能是SCML中的大粒径浮游植物占比显著增加; 3)弱光层中的ξ值较SCML中的高, 但略低于表层的ξ值, 而D_A则位于表层与SCML的D_A之间, 这可能与浮游植物及其碎屑的絮凝、分解、沉降等过程相关。PSD特征影响着海水的固有光学特性, 分析发现: 由于SCML中的叶绿素浓度增加, 颗粒物散射系数(b_p(532))和颗粒物后向散射系数(b_bp(532))也相应呈现显著增加的趋势。弱光层中的平均b_p(532)与平均b_bp(532)最小。ξ与颗粒物衰减光谱斜率之间呈高分散性, Boss 等(2001b)的模型适合用于粗略估算区域性的ξ分布范围及均值。  相似文献   

RESEARCH ON PASSIVE SERVO SEISMIC ROTATIONAL ACCELERATION SENSOR WITH LARGE DAMPING     

QU Ming-zhe  GAO Feng  YANG Xue-shan  YANG Dong-xia 《地震地质》2018,40(5):1170-1178

Many strong motion records show that under the strong seismic vibration of, the torsional disfigurement of building structures is a common and serious damage. At present, there are no special sensors for measuring seismic rotation in the world. Most of the experts obtain rotational components through observing deformation, theoretical analysis and calculation. The theory of elastic wave and source dynamics also prove the conclusion that the surface of the earth will rotate when an earthquake occurs. Based on a large number of investigations and experiments, a rotational acceleration sensor was developed for the observation of the rotational component of strong ground motions. This acceleration sensor is a double-pendulum passive servo large-damped seismic rotational acceleration sensor with the moving coil transducer. When an earthquake occurs, the seismic rotational acceleration acts on the bottom plate at the same time. The magnetic circuit system and the middle shaft fixedly connected to the bottom plate follow the bottom plate synchronous vibration, and the moving part composed of the mass ring, the swing frame and the moving ring produces relative corners to the central axis. The two working coils mounted on the two pendulums produce the same relative motion with respect to the magnetic gaps of the two magnetic circuits. Both working coils at this time generate an induced electromotive force by cutting magnetic lines of force in the respective magnetic gaps. The generated electromotive forces are respectively input to respective passive servo large damper dynamic ring transducer circuits and angular acceleration adjusting circuits, and the signals are simultaneously input to the synthesizing circuit after conditioning. Finally, the composite circuit outputs a voltage signal proportional to the seismic rotational acceleration to form a seismic rotational acceleration sensor. The paper presents the basic principles of the rotational acceleration sensor, including its mechanical structure diagram, circuit schematic diagram and mathematical models. The differential equation of motion and its circuit equation are derived to obtain the expressions of the main technical specifications, such as the damping ratio and sensitivity. The calculation shows that when the damping ratio is much larger than 1, the output voltage of the passive servo large damping dynamic coil transducer circuit is proportional to the ground rotation acceleration, and the frequency characteristic of bandpass is wider when the damping ratio is larger. Based on the calibration test, the dynamic range is greater than or equal to 100dB and the linearity error is less than 0.05%. The amplitude-frequency characteristics, the phase-frequency characteristics and their corresponding curves of the passive servo rotational acceleration sensor are acquired through the calculations. Based on the accurate measurement of the micro-vibration of the precision rotating vibration equipment, the desired result is obtained. The measured data are presented in the paper, which verify the correctness of the calculation result. The passive servo large damping rotational acceleration sensor has simple circuit design, convenient operation and high resolution, and can be widely applied to seismic acceleration measurement of earthquake or structure.  相似文献   

Correspondence between the large volcanic eruptions and ENSO events over AD 1525–2000     

Fang  Xiuqi  Zheng  Xue  Zhang  Xing 《地理学报(英文版)》2020,30(1):103-118

ENSO is an interannual mode which may be affected by external forcing, such as volcanic eruptions. Based on the reconstructed volcanic eruptions chronology and ENSO sequences, both 195 large volcanic eruptions(VEI≥4) and 398 ENSO(El Ni?o and La Ni?a) events were extracted from 1525 to 2000. An analysis of the correspondence between the large volcanic eruptions and ENSO events was performed by matching the large volcanic eruptions with the types and magnitudes of ENSO events present in the 0–2 years after the eruptions. The results show the following:(1) The percentages of ENSO events within the 3 years after the large eruptions had increased to 68.3% from 31.7% compared with those with no-eruptions in the previous 0–2 years. In addition, the ratio of El Ni?o to La Ni?a events turned from 2:3 to 1:1, and more El Ni?o events occurred in the 0 year after eruptions in the low-latitudes of the Northern Hemisphere and in the tropics but more La Ni?a events occurred in the 0 year after in the high-latitudes of the Northern Hemisphere and the Southern Hemisphere.(2) After the eruptions, the weak(W) El Ni?o events had increased by 8 percentage points and the very strong(VS) El Ni?o events had decreased by 10 percentage points; conversely, there was a decrease by 15 percentage points of the weak La Ni?a events and an increase by 11.4 percentage points of the very strong La Ni?a events. Specifically, the percentages of strong La Ni?a events increased to a peak at 1(+1) year after the eruptions.(3) The percentage of eruptions followed by single-year ENSO was the greatest. The percentage of ENSO events that occurred in the consecutive 2 years following an eruption was approximately equal to the percentage of events that occurred consecutively 3 years following an eruption, and both sets of ENSO magnitudes showed a decreasing trend.  相似文献   

水源钻机在超深土层绳索取心钻进中的应用          下载免费PDF全文

杨联锋  段云星 《探矿工程》2020,47(11):44-50

山西省清徐县区域地质调查项目设计800、2000、3000 m科学钻探孔，以调查填补新生界底板埋深控制空白区，各孔钻入基岩30 m完钻。要求全孔取心，岩心采取率≮85%，岩心直径≮60 mm，采用塑料保护管采取原状岩样。针对超深软土层、各组地层特性及厚度未知、钻遇基岩完钻深度未知、大直径高保真全孔取心、项目价格远低于目前市场成本等难题，经过“水源钻机+大提钻取心+长裸眼孔段”实施800 m孔、“岩心钻机+绳索取心+套管固井”实施640 m参数对比孔，创新性使用“水源钻机+绳索取心+长裸眼孔段”工艺完成了2000 m孔的施工。该工艺岩心采取率达到93%，孔径和孔斜符合地质要求，为3000 m孔顺利施工打下了坚实的基础，为同类型项目提供了经验和借鉴。  相似文献   

大规模群桩基础水平承载力效应系数计算研究          下载免费PDF全文

贾鹏  王兰民  杨燕  刘上春 《地震工程学报》2020,42(5):1202-1207

桩基础在水平荷载或地震作用下的承载力计算一直是工程界的一个研究难点，近年来随着建筑、桥梁桩基础的规模大幅增加，基于小规模、小比例尺群桩基础水平承载力试验得出来的结论和计算方法可能会不适应新的计算要求，相关的认识和计算方法需要重新论证和更新。本文针对大规模群桩基础水平承载力效应系数的计算问题，首先对国内外研究进展进行调研，发现现有的规范计算方法可能会高估群桩基础的水平承载力。针对这些问题，对大规模群桩基础的水平承载力效应系数进行有限元数值计算分析，探讨水平承载力效应系数的规律，给出相应的计算方法，并与规范计算方法结果进行对比。本文的研究结果可为相应的工程设计问题提供依据，结果的适用性需要今后进一步的检验。  相似文献