排序方式： 共有5条查询结果，搜索用时 15 毫秒
1
1.
Jewgenij Torizin Michael Fuchs Adnan Alam Awan Ijaz Ahmad Sardar Saeed Akhtar Simon Sadiq Asif Razzak Daniel Weggenmann Faseeh Fawad Nimra Khalid Faisan Sabir Ahsan Jamal Khan 《Natural Hazards》2017,87(2):757-771
This paper presents laboratory experiments and numerical simulations of effects of submerged obstacles on tsunami-like solitary wave and its run-up. This study was carried out for the breaking and non-breaking solitary waves on 1:19.85 uniform slope which contains a submerged obstacle. New laboratory experiments are performed to describe the mitigation of tsunami amplitude and run-up under the effect of submerged obstacles. We are based on experimental results obtained to validate the numerical model. The numerical modeling using COULWAVE aims essentially to show the effect of the obstacle on the shape of solitary wave and the limit of this effect. Using a multiple nonlinear regression, we have determined a model to estimate height of run-up according to the amplitude of the wave and the obstacle peak depth. 相似文献
2.
Mechanical compaction and ultrasonic velocity of sands with different texture and mineralogical composition 总被引：1，自引：0，他引：1
Manzar Fawad Nazmul Haque Mondol Jens Jahren Knut Bjørlykke 《Geophysical Prospecting》2011,59(4):697-720
This study presents the results of experimental compaction while measuring ultrasonic velocities of sands with different grain size, shape, sorting and mineralogy. Uniaxial mechanical compaction tests up to a maximum of 50 MPa effective stress were performed on 29 dry sand aggregates derived from eight different sands to measure the rock properties. A good agreement was found between the Gassmann saturated bulk moduli of dry and brine saturated tests of selected sands. Sand samples with poor sorting showed low initial porosity while sands with high grain angularity had high initial porosity. The sand compaction tests showed that at a given stress well‐sorted, coarse‐grained sands were more compressible and had higher velocities (Vp and Vs) than fine‐grained sands when the mineralogy was similar. This can be attributed to grain crushing, where coarser grains lead to high compressibility and large grain‐to‐grain contact areas result in high velocities. At medium to high stresses the angular coarse to medium grained sands (both sorted sands and un‐sorted whole sands) showed high compaction and velocities (Vp and Vs). The small grain‐to‐grain contact areas promote higher deformation at grain contacts, more crushing and increased porosity loss resulting in high velocities. Compaction and velocities (Vp and Vs) increased with decreasing sorting in sands. However, at the same porosity, the velocities in whole sands were slightly lower than in the well‐sorted sands indicating the presence of loose smaller grains in‐between the framework grains. Quartz‐poor sands (containing less than 55% quartz) showed higher velocities (Vp and Vs) compared to that of quartz‐rich sands. This could be the result of sintering and enlargement of grain contacts of ductile mineral grains in the quartz‐poor sands increasing the effective bulk and shear stiffness. Tests both from wet measurements and Gassmann brine substitution showed a decreasing Vp/Vs ratio with increasing effective stress. The quartz‐rich sands separated out towards the higher side of the Vp/Vs range. The Gassmann brine substituted Vp and Vs plotted against effective stress provide a measure of the expected velocity range to be found in these and similar sands during mechanical compaction. Deviations of actual well log data from experimental data may indicate uplift, the presence of hydrocarbon, overpressure and/or cementation. Data from this study may help to model velocity‐depth trends and to improve the characterization of reservoir sands from well log data in a low temperature (<80–100o C) zone where compaction of sands is mostly mechanical. 相似文献
3.
Oedometric mechanical compaction tests were performed on brine-saturated synthetic samples consisting of silt-clay mixtures to study changes in microfabric and rock properties as a function of effective stress. The silt consisted of crushed quartz (∼100%) with grain size range between 4 and 40 μm, whereas the clay consisted of 81% kaolinite, 14% mica/illite and 5% microcline of grain size between 0.4 and 30 μm. Five sample pairs ranging in composition from pure silt to pure clay were compacted to 5 and 50 MPa effective stress respectively. SEM studies were carried out to investigate microfabric changes in the mechanically compacted silt-clay mixtures. The degree of alignment of the different minerals present (quartz, mica/illite and kaolinite) were computed by using an image analysis software. Experimental compaction have measured the changes in the rock properties such as porosity and velocity as a function of effective stress for different mixtures of clay and silt. Clay-rich samples showed a higher degree of mineral orientation and lower porosity compared to silt-dominated samples as a function of effective stress. Pure clay sample had 11% porosity at 50 MPa effective stress whereas the pure silt sample retained about 29% porosity at the same effective stress. The experiments showed that low porosity down to 11% is possible by mechanical compaction only. A systematic increase in strain was observed in the silt-clay mixtures with increasing clay content but the porosity values found for the 50:50 silt-clay mixture were lower than that of 25:75 silt-clay mixture. No preferential mineral orientation is expected before compaction owing to the high initial porosity suggesting that the final fabric is a direct result of the effective stress. Both P- and S-wave velocities increased in all silt-clay mixtures with increasing effective stress. The maximum P- and S-wave velocities were observed in the 25:75 silt-clay mixture whereas the minimum Vp and Vs were recorded in the pure silt mixture. At 50 MPa effective stress P- wave velocities as high as 3 km/s resulted from experimental mechanical compaction alone. The results show that fine-grained sediment porosity and velocity are dependent on microfabric, which in turn is a function of grain size distribution, particle shape, sediment composition and stress. At 5 MPa effective stress, quartz orientation increased as a function of the amount of clay indicating that clay facilitate rotation of angular quartz grains. Adding clay from 25% to 75% in the silt-clay mixtures at 50 MPa effective stress decreased the quartz alignment. The clay mineral orientation increased by increasing both the amount of clay and the effective stress, the mica/illite fabric alignment being systematically higher than that of kaolinite. Even small amount of silt (25%) added to pure clay reduced the degree of clay alignment significantly. This study demonstrates that experimental compaction of well characterized synthetic mudstones can be a useful tool to understand microfabric and rock properties of shallow natural mudstones where mechanical compaction is the dominant process. 相似文献
4.
Cone Penetration Test Based Direct Methods for Evaluating Static Axial Capacity of Single Piles 总被引：1，自引：0，他引：1
The direct cone penetration test (CPT) based pile design methods use the measured penetrometer readings by scaling relationships or algorithms in a single-step process to enable the assessment of pile capacity components of shaft and base resistance (f p and q b, respectively) for evaluation of full-size pilings. This paper presents a state-of-the-art review of published works that focus on direct CPT evaluation of static axial pile capacity. The review is presented in a chronological order to explicate the evolution over the past six decades of an in situ test based solution for this soil-structure interaction problem. The objective of this study is an attempt to assemble maximum published methods proposed as a result of past investigations in one resource to afford researchers and practitioners with convenient access to the respective design equations and charts. In addition to an all-inclusive summary table and the design charts, a compilation of significant findings and discussions thereof are presented. Furthermore, potential future research directions are indicated, with special emphasis on the optimal use of the modern multi-channel hybrid geophysical-geotechnical seismic CPT to evaluate the complete axial pile load–displacement response. 相似文献
5.
1