高温高压岩石流变仪的围压标定方法     

党嘉祥  周永胜  何昌荣  闫小兵 《地学前缘》2008,15(3):287-291

高温高压岩石流变仪围压标定的主要方法为氯化盐类的部分熔融法和矿物相变法。利用氯化盐类进行压力标定时,不仅可以利用单一盐类,也可以使用多种盐类的混合物;常用的压力标定矿物相变及其适用温压范围如下:石英-柯石英,500~1200℃、2.5~3.2GPa;钠长石-硬玉+石英,600~1200℃、1.6~3.2GPa;铁橄榄石+石英-铁辉石,600~1200℃、1~1.7GPa;磷镁石-Mg3(PO4)2-Ⅱ,565~825℃、0.6~0.9GPa;方解石-文石,600~1200℃、0.5~2.5GPa。不同的标定方法具有不同的特征,文中将进行详细介绍。  相似文献   

Slip-weakening constitutive relation and the structure in the vicinity of a shear crack tip     

Changrong He 《Pure and Applied Geophysics》1995,145(3-4):747-757

Shear-crack model with a cohesive zone (or breakdown zone) is appropriate for the analysis of a fault surface in which slip distribution is strongly nonuniform. As the slipped portion advances, slip-weakening occurs over the so-called cohesive zone, a distance behind the fault tip. For a prescribed strength vs. displacement constitutive relation, however, the zone structure is difficult to determine by an analytical method except for some simple cases, thus it often requires a certain numerical procedure. This work proposes a numerical procedure to obtain approximated solutions of the problem by combining a series of elastic solutions derived bySmith (1974). The series is linearly combined and the unknown coefficients are determined by a nonlinear least square method. This method can fit a wide range of prescribed strength vs. displacement relations which may be simple algebraic relations or curves obtained by laboratory tests. By examining the residual errors and in comparison with a derived result in which linear stress is assumed within the zone, it could be concluded that the results provide good accuracy. Moreover, because the results are written in formulae, they can be easily referred to or used. By fitting constitutive curves in many different shapes, it is found that the stress distribution within the zone is more sensitive to the constitutive curve shape than the displacement. The most interesting fact is that the zone size is not sensitive to the curve shape, i.e., the zone size can be estimated by $$R = 3\mu \zeta \upsilon _c /\{ 2(1 - \upsilon )(\tau _c - \tau _f )\}$$ with ζ=1±0.11 for most cases.  相似文献   

Strength and stability of frictional sliding of gabbro gouge at elevated temperatures   总被引：7，自引：1，他引：7  

Changrong He  Wenming Yao  Zeli Wang  Yongsheng Zhou   《Tectonophysics》2006,427(1-4):217

To investigate the strength of frictional sliding and stability of mafic lower crust, we conducted experiments on oven-dried gabbro gouge of 1 mm thick sandwiched between country rock pieces (with gouge inclined 35° to the sample axis) at slip rates of 1.22 × 10^− 3 mm/s and 1.22 × 10^− 4 mm/s and elevated temperatures up to 615 °C. Special attention has been paid to whether transition from velocity weakening to velocity strengthening occurs due to the elevation of temperature.Two series of experiments were conducted with normal stresses of 200 MPa and 300 MPa, respectively. For both normal stresses, the friction strengths are comparable at least up to 510 °C, with no significant weakening effect of increasing temperature. Comparison of our results with Byerlee's rule on a strike slip fault with a specific temperature profile in the Zhangbei region of North China shows that the strength given by experiments are around that given by Byerlee's rule and a little greater in the high temperature range.At 200 MPa normal stress, the steady-state rate dependence a − b shows only positive values, probably still in the “run-in” process where velocity strengthening is a common feature. With a normal stress of 300 MPa, the values of steady-state rate dependence decreases systematically with increasing temperature, and stick-slip occurred at 615 °C. Considering the limited displacement, limited normal stress applied and the effect of normal stress for the temperatures above 420 °C, it is inferred here that velocity weakening may be the typical behaviour at higher normal stress for temperature above 420 °C and at least up to 615 °C, which covers most of the temperature range in the lower crust of geologically stable continental interior. For a dry mafic lower crust in cool continental interiors where frictional sliding prevails over plastic flow, unstable slip nucleation may occur to generate earthquakes.  相似文献   

Velocity and anisotropic structure in the crust-upper mantle beneath South China and its implications for deep mineralization     

Guoming Jiang  Guibin Zhang  Hongyi Li  Changrong Zhang 《《地质学报》英文版》2018,92(Z1):219-219

  相似文献   

一次冬季冰雹的双偏振多普勒天气雷达回波分析     

江慧远  魏鸣  张深寿  潘佳文  罗昌荣  林文 《气象科学》2019,39(6):755-762

为研究双偏振雷达资料在冬季冰雹监测预警中的应用,利用厦门S波段双偏振雷达资料,分析了2016年12月21日福建漳州冰雹的回波特征。发现在降雹过程中,最强回波达69 dBZ,三体散射回波径向长度达16 km,旁瓣回波切向宽达20 km,低层的钩状回波与入流缺口明显;冰雹区的差分反射率因子Z_(dr)和差分相位常数K_(dp)数值小,冰水混合区的相关系数ρ_(hv)较低。分析表明:此冰雹个例并非典型的超级单体,但存在超级单体的部分偏振回波特征,回波前侧下沉气流存在Z_(dr)弧,可延伸到中层,在入流缺口和后侧下沉气流处,Z_(dr)柱和K_(dp)柱成对出现,中层存在CC的低值环。  相似文献   

双雷达风场反演拼图在登陆台风“莫兰蒂”(1614)强降水精细预报中的同化应用试验   总被引：4，自引：2，他引：2  

王叶红  赵玉春  罗昌荣  韩颂雨 《气象学报》2019,77(4):617-644

利用福建龙岩、漳州、泉州新一代多普勒天气雷达和厦门海沧双偏振雷达探测资料,采用动态地球坐标系下双雷达三维风场反演与拼图技术,基于天气研究和预报模式（Weather Research and Forecasting,WRF）及其资料同化系统,对登陆台风“莫兰蒂”（1614）引起的2016年9月14—15日福建强降水过程进行了双雷达风场反演拼图资料检验及其三维变分同化对强降水精细预报影响的数值试验,结果发现:（1）动态地球坐标系下双雷达反演风场能合理反映实际风场分布状况,其误差相对较小。相较厦门翔安风廓线雷达及厦门探空秒级测风数据,反演风风向（风速）平均绝对误差分别为7.8°（2.6 m/s）及3.4°（1.1 m/s）;（2）反演风场水平方向稀疏化对同化及预报结果极为重要,过密的反演风场资料会给同化及预报结果带来负效果。文中采用18、6、2 km 3重嵌套,在3重嵌套区域均进行同化以及仅在2 km区域进行同化两种情况下,均表现为当反演风场资料水平分辨率提高到0.1°时,同化分析及预报的台风环流开始受到负影响;且当反演风场资料水平分辨率越高时,负效果越明显。敏感性试验结果显示,分辨率取0.2°时数值预报效果最好;（3）以美国国家环境预报中心全球预报系统（National Centers for Environmental Prediction/Global Forecast System,NCEP/GFS）0.5°×0.5°分析场为初值,基于3个不同起报时刻（2016年9月14日14时、20时及15日02时）（北京时,下同）模拟的福建省境内台风内核雨带和螺旋雨带逐时演变、台风路径与强度、逐时降水TS评分和空间相关差异显著,其中14日14时起报试验效果最好;而14日20时起报试验效果最差,这与该试验初始台风大风轴风速明显偏大有关;（4）在上述3个不同起报时刻试验基础上,分别增加双雷达反演风场资料的三维变分同化后,福建境内地面风场和台风内核雨带、螺旋雨带逐时分布、逐时降水TS评分和空间相关、台风环流结构以及U、V风垂直廓线分布均有明显改善,最大正影响时效可达24 h;但仅对1—6 h时效内台风路径有改善。   相似文献   

利用AMDAR数据分析厦门、泉州双雷达三维风场反演误差     

张晗昀  罗昌荣  崔梦雪  蚁志鸿  张伟  陈德花 《大气科学学报》2020,43(4):699-706

利用2016年全年进出厦门机场和晋江机场航班的AMDAR(Aircraft Meteorological DAta Relay)数据对双雷达反演风场进行检验,分析了厦门、泉州双雷达风场反演的总体误差,研究结果表明:1)验证了双雷达连线附近区域反演风场的平均绝对误差较大,发现了与两部雷达连线的夹角小于15°和大于165°的区域的反演结果的平均绝对误差明显大于误差的年平均值。2)对于反演风向而言,误差随着高度增加而减小。对于反演风速而言,高度在9 km以下的反演误差在5 m/s左右,而9 km以上的反演误差较小。3)剔除了双雷达连线附近区域(与两部雷达连线的夹角小于15°和大于165°的区域)和反射率因子小于5 dBZ以及等于100 dBZ(剔除非气象回波)的反演结果后,双雷达反演风场误差较小,相对于AMDAR数据的风向年平均绝对误差为29.4°,风速年平均绝对误差为3.28 m/s,总体误差在可接受范围之内,反演结果接近"真值",该反演方法稳定可靠。  相似文献   

An experimental study of effect of pre‐existing fabric on deformation of foliated mylonite at high temperature and pressure     

Gui Liu  Yongsheng Zhou  Changrong He  Wenming Yao  Junlai Liu  Yuanyuan Zhang 《Geological Journal》2016,51(1):92-112

We performed deformation experiments on a foliated mylonite under high temperature and pressure conditions in this study. To investigate the effect of pre‐existing fabric on the rheology of rocks, our samples were drilled from natural mylonite with the cylinder axis parallel to the foliation (PAR) and perpendicular to the foliation (PER). We performed 25 tests on seven PAR samples and 21 tests on seven PER samples at temperatures ranging from 600 to 890 °C, confining pressures ranging from 800 to 1400 MPa, and steady‐state strain rates of 1 × 10⁻⁴, 1 × 10⁻⁵ and 2.5 × 10⁻⁶ s⁻¹. In the temperatures of 600–700 °C, the deformation is accommodated by semi‐brittle flow, with the average stress exponent being 6–7 assuming power law flow; in the temperature range of 800–890 °C, deformation is mainly by plastic flow, with an average stress exponent of n = 3 and activation energies of Q = 354 ± 52 kJ/mol (PER and PAR samples). The experimental results show that the strengths of PER samples are higher than those of PAR samples. Deformation microstructures have been studied by optical and electron microscopy. The original foliation of PER samples is destroyed by deformation and replaced by a new foliation, but the deformation of PAR samples followed the original foliation. Electron backscatter diffraction (EBSD) measurements show a strong lattice preferred orientation (LPO) of the quartz c axis fabrics of the starting samples and deformed PER and PAR samples. However, the c axis fabric of quartz in experimentally deformed PER and PAR samples varied with temperature and strain rate is different from that seen in the starting mylonite sample. The initial quartz c axis fabric of the starting mylonite sample has been transformed into a new fabric during experimental deformation. Dehydration melting of biotite and hornblende occurred in both PER and PAR samples at temperatures of 800–890 °C. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

利用H/V方法研究琼北火山区的浅表层地质变化特征     

曹佳俊  郭震  夏少红  张昌榕  吴晓阳  任鹏飞 《热带海洋学报》2022,41(1):184-193

海南琼北活火山作为华南沿海重要的第四纪火山, 一直受到国内外学者的广泛关注, 目前对该火山的形成演化已开展了大量深部地质结构的研究, 但对其表层地质结构特征仍然缺乏详细了解。水平-垂直频谱比法(简称H/V方法)已被广泛应用于浅表层地质结构的研究, 本文基于35个便携式微功耗地震仪组成的流动台阵观测数据, 采用经典全波场H/V_(full)和瑞利波椭圆率H/V_(Ray)分析方法, 获得了琼北火山区H/V曲线峰值频率(F₀)和放大倍数(A₀)的空间变化特征。琼北火山区H/V曲线峰值频率变化强烈, 以长流-仙沟断裂为界, 断裂西南侧很难从H/V曲线中获取清晰的F₀和A₀, 而断裂东北侧则存在明显的F₀和A₀。结合已有地质资料, 本文认为长流-仙沟断裂西南侧处于凹陷区, 其浅表层火山岩未发生明显的风化作用, 而东北侧位于隆起区域, 地表火山岩受到了比较严重的风化作用。这一研究结果表明, H/V方法可反映表层火山岩的风化状态, 火山岩出露场地H/V曲线的峰值频率和放大倍数随风化作用程度的增强而表现得更加明显。本研究为琼北火山区浅表火山岩风化状态和地震危险性评估提供了重要的信息支撑。  相似文献   

The influence of turbulent mixing on the subsurface chlorophyll maximum layer in the northern South China Sea     

Shang  Chenjing  Liang  Changrong  Chen  Guiying  Gao  Yongli 《中国海洋湖沼学报》2021,39(6):2167-2180

Journal of Oceanology and Limnology - We present observations from deployments of turbulent microstructure instrument and CTD package in the northern South China Sea from April to May 2010. From...  相似文献