排序方式： 共有2条查询结果，搜索用时 0 毫秒
1
1.
The possibility of recrystallization is a long‐standing barrier to deciphering the genetic origin of dolomites. There is often uncertainty regarding whether or not characteristics of ancient dolomites are primary or the consequence of later recrystallization unrelated to the original dolomitization event. Results from 65 new high‐temperature dolomite synthesis experiments (1 m , 1·0 Mg/Ca ratio solutions at 218°C) demonstrate dolomite recrystallization affecting stoichiometry, cation ordering and nanometre‐scale surface texture. The data support a model of dolomitization that proceeds by a series of four unique phases of replacement and recrystallization, which occur by various dissolution–precipitation reactions. During the first phase (induction period), no dolomite forms despite favourable conditions. The second phase (replacement period) occurs when Ca‐rich dolomite products, with a low degree of cation ordering, rapidly replace calcite reactants. During the replacement period, dolomite stoichiometry and the degree of cation ordering remain constant, and all dolomite crystal surfaces are covered by nanometre‐scale growth mounds. The third phase (primary recrystallization period), which occurs in the experiments between 97% and 100% dolomite, is characterized by a reduced replacement rate but concurrent increases in dolomite stoichiometry and cation ordering. The end of the primary recrystallization period is marked by dolomite crystal growth surfaces that are covered by flat, laterally extensive layers. The fourth phase of the reaction (secondary recrystallization period) occurs when all calcite is consumed and is characterized by stoichiometric dolomite with layers as well as a continued increase in the degree of cation ordering with time. Inferences of recrystallization, in natural dolomite, based on cation order or stoichiometry of dolomite, usually depend on assumptions about the precursor dolomite subjected to recrystallization. If it is assumed that the experimental evidence presented here is applicable to natural, low‐temperature dolomites, then the presence of mounds is direct evidence of a lack of recrystallization and the presence of layers is direct evidence of recrystallization. 相似文献
2.
Examination with scanning electron microscopy (SEM) and scanning force microscopy (SFM) revealed etch pits, layers and islands on dolomite crystal faces synthesized from calcite in Ca‐Mg‐Cl solutions at 200 °C and a wide variety of natural dolomites. Layers are broad, flat structures bounded by steps less than 100 nm high and greater than 1 μm wide. Islands are rounded topographic highs <20 nm high and <200 nm wide. The nanotopography of synthetic dolomite changed from islands throughout most of the reaction to layers at 100% dolomite. Island nanotopography formed on both Ca‐rich and near‐stoichiometric dolomite. Analyses of reaction products from dolomite synthesis indicates that there are no SFM‐detectable products formed in <10 h. SEM‐detectable products formed in 15 h. X‐ray diffraction (XRD)‐detectable products formed in ≈18 h, and the reaction went to completion in ≈40 h. Based on SFM analyses, the induction period for dolomitization in these experiments accounts for ≈20% of the total reaction time necessary to dolomitize CaCO3 completely under the experimental conditions used here. Island nano‐ topography is inferred to occur at higher degrees of supersaturation than layer nanotopography for three reasons. First, island nanotopography on synthetic calcite and gypsum forms at higher supersaturations than layer nanotopography. Secondly, island nanotopography formed in solutions with higher degrees of supersaturation with respect to dolomite. Thirdly, the greater surface roughness of a crystal face composed of islands compared with layers indicates that island surfaces have higher surface energy than layer surfaces. Therefore, the stability of island surfaces requires a higher degree of supersaturation. Because islands and layers form under a wide range of conditions, their presence provides broadly applicable criteria for evaluating relative degrees of supersaturation under which ancient dolomite formed. Comparison of synthetic dolomites with natural dolomites demonstrates (1) similar nanotopography on natural and synthetic dolomites and (2) both natural planar and non‐planar dolomite may have island nanotopography. 相似文献
1