沸石强化过滤的中试及生产性试验研究   总被引：2，自引：0，他引：2  

丁磊  王萍 《矿物学报》2008,28(3)

对新型水处理材料沸石强化常规给水处理工艺进行了中试和生产性试验,并与石英砂滤料做了对比.中试结果表明粒径为0.80-1.20mm沸石对浊度、氨氮、有机物都表现出良好的去除效果,过滤时的水头损失、反冲洗强度明显小于石英砂,不仅能满足反冲洗要求,还可节省反冲洗水量,降低运行成本.在生产性试验条件下,沸石对浊度、氨氮、耗氧量的去除率分别为95%、83%和39%.因此,在当前水源水遭到污染的情况下,用沸石替代石英砂滤料可明显改善水质,在不增加处理构筑物的情况下,对给水处理工艺可起到强化作用  相似文献   

渤海中南部悬浮物海洋调查资料分析   总被引：6，自引：0，他引：6  

苏健  江文胜  孙文心 《中国海洋大学学报(自然科学版)》2001,31(5):647-652

对于悬浮物 (SPM)的研究目前已引起诸多学者关注。作者利用 1998和 1999年的中德合作海洋调查所获得的资料进行分析。主要进行三个方面的工作 :研究悬浮物与透明度的关系 ;研究悬浮物与浊度的关系 ;估计海底剪切速度。并为研究悬浮物输运提供资料和作前期研究  相似文献   

南海东部海域柱样沉积物浊流沉积探讨     

章伟艳  张富元  张霄宇 《热带海洋学报》2003,22(3):36-43

利用1998年南海东部陆坡69号柱样、深海盆149号柱样、南部岛礁323号柱样沉积物的粒度、化学、古生物、矿物等鉴定分析测试资料,分析了南海东部海域发生浊流沉积的地质背景、产生浊流沉积的条件和诱发因素,进而发现南海东部浊流沉积发育,在南北陆坡及中部深海盆地均有浊流沉积层。从其出现层位看,为氧同位素2—4期,即晚更新世中晚期。从浊流沉积出现层数分析,具有自北向南浊流发生频次减弱的趋势。从浊流沉积物成分看,南海东部浊流沉积物具有多样性,北部陆坡以陆源为主,中部深海盆以陆源及火山源为主,南部岛礁以生物源为主。  相似文献   

鸭绿江洪季的河口最大混浊带   总被引：4，自引：0，他引：4  

金惜三  李炎 《海洋学研究》2001,19(1):1-10

对 1 994年 8月在鸭绿江河口的水文和悬浮泥沙的观测资料进行分析。结果表明 ,在洪季鸭绿江河口的最大混浊带 ,出现在第一个河口锋面内侧。它的核心处盐度小于 1 ,从上游带入河口的细颗粒泥沙多数被河口第一锋面截留 ,还有一部分上游来沙穿过该锋面 ,聚集在河口第一和第二锋面之间。垂向密度环流作用和絮凝作用在鸭绿江洪季最大混浊带的维持过程中起着主导作用  相似文献   

长江口枯季悬沙粒度与浓度之间的关系   总被引：4，自引：0，他引：4  

王爱军  汪亚平  高抒  潘少明 《海洋科学进展》2005,23(2):159-167

2003和2004年枯季在长江口采集水样并作水文观测，对所获水样进行过滤和粒度分析，以计算悬沙浓度和悬沙粒度分布。结果表明，2003年11月小潮期间，悬沙中值粒径与悬沙浓度存在着显著的指数关系，在大潮期间没有显著关系；在2004年2月小湖期间，两者之间没有显著关系，但在大潮期间存在着显著的指数关系。枯季水体悬沙以粉砂组份为主，并且随着向口外的推移，细颗粒组份逐渐增加，但在拦门沙最大浑浊带附近，由于絮凝作用，沉积物粒度变幅较大，可产生粒径粗化的现象。小潮期间，砂含量较低，但与悬沙浓度之间有显著相关关系；大潮期间，悬沙粒径粗化，但砂含量与悬沙浓度之间的关系不显著。上述分布趋势与沉积物来源、当地的水动力条件和絮凝作用等因素有密切关系。  相似文献   

Quantitative analysis of variations in depositional sequence thickness from submarine channel levees   总被引：2，自引：0，他引：2  

Kenneth I. Skene  David J. W. Piper†  Paul S. Hill 《Sedimentology》2002,49(6):1411-1430

Abstract Thickness variations across‐levee and downchannel in acoustically defined depositional sequences from six submarine channel‐levee systems show consistent and quantifiable patterns. The thickness of depositional sequences perpendicular to the channel trend, i.e. across the levee, decreases exponentially, as characterized by a spatial decay constant, k. Similarly, the thickness of sediment at the levee crest decreases exponentially down the upper reaches of submarine channels and can be characterized by a second spatial decay constant, λ. The inverse of these decay constants has units of length and defines depositional length scales such that k^?1 is a measure of levee width and λ^?1 is a measure of levee length. Quantification of levee architecture in this way allowed investigation of relationships between levee architecture and channel dimensions. It was found that these measures of levee e‐folding width and levee e‐folding length are directly related to channel width and relief. The dimensions of channels and levees are thus intimately related, thereby limiting the range of potential channel‐levee morphologies, regardless of allocyclic forcing. A simple sediment budget model relates the product of the levee e‐folding width and e‐folding length to through‐channel volume discharge. A classification system based on the quantitative downchannel behaviour of levee architecture allows identification of a ‘mid‐channel’ reach, where sediment is passively transferred from the through‐channel flow to the levees as an overspilling flow. Downstream from this reach, the channel gradually looses its control on guiding turbidity currents, and the resulting flow can be considered as an unconfined or spreading flow.  相似文献   

Facies of slurry-flow deposits, Britannia Formation (Lower Cretaceous), North Sea: implications for flow evolution and deposit geometry   总被引：4，自引：0，他引：4  

Donald R. Lowe  Martin Guy†  Andrew Palfrey† 《Sedimentology》2003,50(1):45-80

ABSTRACT Mud‐rich sandstone beds in the Lower Cretaceous Britannia Formation, UK North Sea, were deposited by sediment flows transitional between debris flows and turbidity currents, termed slurry flows. Much of the mud in these flows was transported as sand‐ and silt‐sized grains that were approximately hydraulically equivalent to suspended quartz and feldspar. In the eastern Britannia Field, individual slurry beds are continuous over long distances, and abundant core makes it possible to document facies changes across the field. Most beds display regular areal grain‐size changes. In this study, fining trends, especially in the size of the largest grains, are used to estimate palaeoflow and palaeoslope directions. In the middle part of the Britannia Formation, stratigraphic zones 40 and 45, slurry flows moved from south‐west and south towards the north‐east and north. Most zone 45 beds lens out before reaching the northern edge of the field, apparently by wedging out against the northern basin slope. Zone 40 and 45 beds show downflow facies transitions from low‐mud‐content, dish‐structured and wispy‐laminated sandstone to high‐mud‐content banded units. In zone 50, at the top of the formation, flows moved from north to south or north‐west to south‐east, and their deposits show transitions from proximal mud‐rich banded and mixed slurried beds to more distal lower‐mud‐content banded and wispy‐laminated units. The contrasting facies trends in zones 40 and 45 and zone 50 may reflect differing grain‐size relationships between quartz and feldspar grains and mud particles in the depositing flows. In zones 40 and 45, quartz grains average 0·30–0·32 mm in diameter, ≈ 0·10 mm coarser than in zone 50. The medium‐grained quartz in zones 40 and 45 flows may have been slightly coarser than the associated mud grains, resulting in the preferential deposition of quartz in proximal areas and downslope enrichment of the flows in mud. In zone 50 flows, mud was probably slightly coarser than the associated fine‐grained quartz, resulting in early mud sedimentation and enrichment of the distal flows in fine‐grained quartz and feldspar. Mud particles in all flows may have had an effective grain size of ≈ 0·25 mm. Both mud content and suspended‐load fallout rate played key roles in the sedimentation of Britannia slurry flows and structuring of the resulting deposits. During deposition of zones 40 and 45, the area of the eastern Britannia Field in block 16/26 may have been a locally enclosed subbasin within which the depositing slurry flows were locally ponded. Slurry beds in the eastern Britannia Field are ‘lumpy’ sheet‐like bodies that show facies changes but little additional complexity. There is no thin‐bedded facies that might represent waning flows analogous to low‐density turbidity currents. The dominance of laminar, cohesion‐dominated shear layers during sedimentation prevented most bed erosion, and the deposystem lacked channel, levee and overbank facies that commonly make up turbidity current‐dominated systems. Britannia slurry flows, although turbulent and capable of size‐fractionating even fine‐grained sediments, left sand bodies with geometries and facies more like those deposited by poorly differentiated laminar debris flows.  相似文献   

矿坑水净化处理与利用   总被引：4，自引：0，他引：4  

邵爱军  王晓东 《水文地质工程地质》1997,24(1):46-48

本文论述了矿坑水的净化处理方法与工艺流程，主要处理方法有混凝，沉淀，过滤及消毒，不同水质特点应选用不同的处理方法和工艺流程，最后通过实例说明了矿坑水净化处理与利用，具有明显的社会效益，经济效益和环境效益。  相似文献   

Beds comprising debrite sandwiched within co-genetic turbidite: origin and widespread occurrence in distal depositional environments   总被引：11，自引：0，他引：11  

P. J. Talling  L. A. Amy†  R. B. Wynn‡  J. Peakall†  M. Robinson 《Sedimentology》2004,51(1):163-194

Co‐genetic debrite–turbidite beds occur in a variety of modern and ancient turbidite systems. Their basic character is distinctive. An ungraded muddy sandstone interval is encased within mud‐poor graded sandstone, siltstone and mudstone. The muddy sandstone interval preserves evidence of en masse deposition and is thus termed a debrite. The mud‐poor sandstone, siltstone and mudstone show features indicating progressive layer‐by‐layer deposition and are thus called a turbidite. Palaeocurrent indicators, ubiquitous stratigraphic association and the position of hemipelagic intervals demonstrate that debrite and enclosing turbidite originate in the same event. Detailed field observations are presented for co‐genetic debrite–turbidite beds in three widespread sequences of variable age: the Miocene Marnoso Arenacea Formation in the Italian Apennines; the Silurian Aberystwyth Grits in Wales; and Quaternary deposits of the Agadir Basin, offshore Morocco. Deposition of these sequences occurred in similar unchannellized basin‐plain settings. Co‐genetic debrite–turbidite beds were deposited from longitudinally segregated flow events, comprising both debris flow and forerunning turbidity current. It is most likely that the debris flow was generated by relatively shallow (few tens of centimetres) erosion of mud‐rich sea‐floor sediment. Changes in the settling behaviour of sand grains from a muddy fluid as flows decelerated may also have contributed to debrite deposition. The association with distal settings results from the ubiquitous presence of muddy deposits in such locations, which may be eroded and disaggregated to form a cohesive debris flow. Debrite intervals may be extensive (> 26 × 10 km in the Marnoso Arenacea Formation) and are not restricted to basin margins. Such long debris flow run‐out on low‐gradient sea floor (< 0·1°) may simply be due to low yield strength (? 50 Pa) of the debris–water mixture. This study emphasizes that multiple flow types, and transformations between flow types, can occur within the distal parts of submarine flow events.  相似文献   

Optimisation de la quantification des flux de matière en suspension d'un cours d'eau alpin : l'Isère à Grenoble (France)     

Dominique Dumas 《Comptes Rendus Geoscience》2004,336(13):1149-1159

This study seeks to determine suspended-matter flux of the Isère at Grenoble, one of the most important rivers of the northern French Alps. Since 1994, and especially 1996, systematic samplings of the left bank make it possible to follow in one point the variations of suspended particles and matter (SPM) of this river. But from a single measurement, sometimes not very representative of the whole observable concentrations within the section, it remains still difficult to estimate precisely the SPM flux. The results of this study show in particular the successive appearance of several turbidity gradients, whose occurrence is explained mainly by the hydrological and hydro-sedimentary dynamics of this river. The estimate of these gradients thus makes it possible to extrapolate specific measurements more easily and consequently to daily define the quantities of suspended matter exported by the Isère. Since 1996, the results show a very high flow, specific of the Isère at Grenoble, variable between 124 and more than 460 t km^?2 yr^?1. To cite this article: D. Dumas, C. R. Geoscience 336 (2004).  相似文献