首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 546 毫秒
1.
This article presents a laboratory study of static behavior of silty-sand soils. The objective of this laboratory investigation is to study the effect of initial confining pressures and fines content on the undrained shear strength (known as liquefaction resistance) response, pore pressure, and hydraulic conductivity of sand–silt mixtures. The triaxial tests were conducted on reconstituted saturated silty-sand samples at initial relative density Dr = 15% with fines content ranging from 0 to 50%. All the samples were subjected to a range of initial confining pressures (50, 100, and 200 kPa). The obtained results indicate that the presence of low plastic fines in sand–silt mixture leads to a more compressible soil fabric, and consequently to a significant loss in the soil resistance to liquefaction. The evaluation of the data indicates that the undrained shear strength can be correlated to fines content (Fc), inter-granular void ratio (eg), and excess of pore pressure (Δu). The undrained shear strength decreases with the decrease of saturated hydraulic conductivity and the increase of fines content for all confining pressures under consideration. There is a relatively high degree of correlation between the peak shear strength (qpeak) and the logarithm of the saturated hydraulic conductivity (ksat) for all confining pressures.  相似文献   

2.
The hydraulic conductivity plays a major role on the excess pore pressure generation during monotonic and cyclic loading of granular soils with fines. This paper aims to determine how much the hydraulic conductivity and pore pressure response of the sand-silt mixtures are affected by the percentage of fines and void ratio of the soil. The results of flexible wall permeameter and undrained monotonic triaxial tests performed on samples reconstituted from Chlef River sand with 0, 10, 20, 30, 40, and 50% nonplastic silt at an effective confining stress of 100 kPa and two relative densities (Dr = 20, and 91%) are presented and discussed. It was found that the pore pressure increases linearly with the increase of the fines content and logarithmically with the increase of the intergranular void ratio. The results obtained from this study reveal that the saturated hydraulic conductivity (k) of the sand mixed with 50% low plastic fines can be, on average, four orders of magnitude smaller than that of the clean sand. The results show also that the hydraulic conductivity decreases hyperbolically with the increase of the fines content and the intergranular void ratio.  相似文献   

3.
ABSTRACT

The behavior of loose anisotropically consolidated calcareous sand obtained from an island in the South China Sea was investigated under undrained monotonic and cyclic loading in a hollow cylinder torsional apparatus. The tests were conducted on specimens which consolidated under various initial effective confining pressures and consolidation stress ratios. The monotonic test results show that the failure and phase transformation line are essentially independent of the consolidation conditions, while the initial contractive tendency of the specimens decreases with an increasing consolidation stress ratio. During monotonic loading of the anisotropically consolidated specimens, a same major principal stress direction is observed at the constant stress ratio lines up to the phase transformation line, irrespective of initial effective confining pressure. The cyclic strength of the sand increases with an increasing consolidation stress ratio. Moreover, a pronounced stress dependence is observed in the sand with higher consolidation stress ratio. During cyclic loading, the generated excess pore water pressure presents considerable fluctuations. The normalized terminal excess pore water pressure is described as a function of consolidation stress ratio. The tests show that the particle shape, rather than particle crushing, plays an important role in the monotonic and cyclic behaviors of the calcareous sand.  相似文献   

4.
Abstract

The strength of saturated clays subjected to low‐frequency cyclic loading is of considerable importance in the design of offshore structures. A series of postcyclic undrained triaxial strength tests were carried out on samples of a silty clay (Keuper Marl), which had not failed under cyclic loading, to investigate the effect of this loading on the postcyclic monotonie effective stress path and strength of the soil. Undrained cyclic loading of normally consolidated and lightly overconsolidated samples by generating positive pore pressures caused the apparent degree of overconsolidation to increase. Samples subsequently subjected to monotonie testing followed effective stress paths commensurate with this apparent overconsolidation and failed on the “Hvorslev” surface on the “dry” side of the stable state boundary surface rather than on the critical state as would be expected of samples of this initial stress history. Samples which were initially heavily overconsolidated did not generate large pore pressures under cyclic loading and did not therefore exhibit large changes in postcyclic monotonie strength. The reduction in strength after cyclic loading therefore is greater for normally consolidated and lightly overconsolidated samples. The pore pressures generated under postcyclic monotonie loading are related to the degree of apparent overconsolidation achieved during cyclic loading.  相似文献   

5.
From this research, overconsolidated undrained and drained behaviors of specimens with high sand content were highly dilatant. According to the comparison results of laboratory tests, the deviator stresses of silty sand were greater than sandy silt due to high sand content under increasing OCRs, and both silty sand and sandy silt were presented strain softening tendency after failure under undrained loading. The pore water pressure increased with increasing fines content under increasing OCRs. Silty sand exhibited more dilatancy and increasing shear strength than sandy silt because pore water pressures of silty sand were lower than sandy silt under higher OCRs. In overconsolidated drained tests, silty sand is higher strength than sandy silt because silty sand has a lower volumetric strain and higher deviator stress than sandy silt under increasing OCRs. As the degree of overconsolidation increased, similar behaviors of silty sand and sandy silt observed that volumetric strain decreased to negative values due to dilatancy effect and low-cohesion under current effective confining pressures.  相似文献   

6.
Analysis of wave-induced liquefaction in seabed deposits of silt   总被引：1，自引：0，他引：1  
The dynamic stress introduced in half elastic space by wave loading is characterized by the equation between the magnitude of half cyclic axial stress and cyclic torsion shear stress and the principal stress,whose direction rotates continuously and compression stress on seabed can be calculated by the use of small amplitude wave theory.With relationship curves of saturated silt of liquefaction cycles and cyclic stress ratios obtained by cyclic triaxial-torsional coupling shear tests and curve fitting method to different data points of relative density,it is suggested that the cyclic stress ratio corresponding to constant liquefaction impedance be taken as the critical cyclic stress ratio which implies liquefaction.There exists a linear relationship between critical cyclic stress ratio and relative density under different relative densities.Empirical formula for critical cyclic stress ratios of seabed liquefaction induced by wave loading under different relative densities is established.The possibility of seabed silt liquefaction and its influence factors are analyzed based on the small-amplitude wave theory and the data acquired in laboratory tests.  相似文献   

7.
Cyclic vertical-torsional coupling tests were performed on saturated Nanjing fine sand with a relative density of 50% using a hollow cylinder apparatus. The effect of complex initial stress conditions on undrained dynamic strength of saturated Nanjing fine sand was investigated. It is shown that the initial confining pressure, p0, the initial stress ratio, R0, and the initial angle of maximum principal stress direction, α0, have great effects on the characteristics of the dynamic strength of Nanjing fine sand. The dynamic strength increases with p0 and R0, while it decreases with α0. The effect of initial intermediate principal stress parameter b0 on the dynamic strength is slight.  相似文献   

8.
Characteristics of Pore Water Pressure of Saturated Silt Under Wave Loading   总被引：1，自引：0，他引：1  
The characteristics of dynamic stress in the seabed under wave loading are constant principal stress and continuous rotation of the principal stress direction.Cyclic triaxial-torsional coupling shear tests were performed on saturated silt by the hollow cylinder apparatus under different relative densities,deviator stress ratios and vibration frequencies to study the development of pore water pressure of the saturated silt under wave loading.It was found that the development of pore water pressure follows the trend of "fast～steady～drastic".The turning point from fast to steady stage is not affected by relative density and deviator stress ratio.However,the turning point from steady to drastic stage relies on relative density and deviator stress ratio.The vibration cycle for the liquefaction of saturated silt decreases with increasing deviator stress ratio and increases with relative density.The vibration cycle for the liquefaction of the saturated silt increases with vibration frequency and reaches a peak value,after which it decreases with increasing vibration frequency for the relative density of 70%.But the vibration cycle for the liquefaction of saturated silt increases with vibration frequency for the relative density of 30%.The development of pore water pressure of the saturated silt is influenced by relative density and vibration frequency.  相似文献   

9.
The post-cyclic behavior of biogenic carbonate sand was evaluated using cyclic triaxial testing through a stress control method under different confining pressures between 50 to 600 kPa. The testing program included a series of isotropically and anisotropically consolidated, undrained triaxial compression and extension tests on samples of remolded calcareous Bushehr sand. Grading analyses (before and after each test) were used to examine the influence of particle breakage on post-cyclic behavior of Bushehr sand. The particle breakage commonly occurred in these soils even in lower values of confining pressure, yet there was not a clear correlation between the post-cyclic responses and particle breakage. Based on the present study, a concept is suggested for post-cyclic behavior of carbonate sand. It was observed that post-cyclic strength has a good correlation with cyclic stress ratio, type of consolidation, and value of residual cyclic strain. For all specimens, it is clear that the post-cyclic strength is greater than monotonic strength, irrespective of confining pressure and relative density.  相似文献   

10.
Abstract

This article presents an experimental investigation on the dynamic consolidation (DC) drainage behavior of soft marine clays. A sinusoidal harmonic load with different frequencies was applied to simulate the DC method in which the conventional impact load was replaced by the cyclic load. Four geotextile-filter strips were used to form the side drainage channels simulating the wick drain method. A series of loading tests were conducted on soft soil specimens at different confining pressures (i.e., 20, 40, 70, and 100?kPa) and different vibration frequencies (i.e., 0, 0.5, 1, 1.5, 2, and 5?Hz). Test results showed that both confining pressure and frequency have significant influences on the drainage behavior of soft marine clay specimens. The magnitude of drainage volume consistently decreases linearly with increasing confining pressure. Compared to static loading condition, specimens under cyclic loading condition at different frequencies show a better drainage performance. Specimen at applied frequency of 1?Hz exhibits the maximum cumulative drainage volume due to the resonant effect.  相似文献   

11.
Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian University of Technology was employed to perform different types of test on saturated soft marine clay in the Yangtze estuary. Undisturbed samples of the clay were subjected to undrained cyclic vertical and torsional coupling shear and cyclic torsional shear after three-directional anisotorpic consolidation with different initial consolidation parameters. Investigated were the effects of the initial orientation angle of the major principal stress, initial ratio of deviatoric stress, initial coefficient of intermediate principal stress and continuous rotation of principal stress axes on the stiffness degradation. It is found that the degradation index decreases (or degradation degree increases) significantly with increasing initial orientation angle of the major principal stress and initial ratio of deviatoric stress. Compared to the effects of the initial orientation angle of the major principal stress and initial ratio of deviatoric stress, the effect of initial coefficient of intermediate principal stress is less evident and this trend is more clearly reflected by the results of the cyclic torsional shear tests than those of the cyclic coupling shear tests. At the same cycle number, the degradation index obtained from the cyclic torsional shear test is higher than that from the cyclic coupling shear test. The main reason is that the continuous rotation in principal stress directions during cyclic coupling shear damages the original structure of the soil more than the cyclic torsional shear does. Based on a series of experiments, a mathematical model for stiffness degradation is proposed and the relevant parameters are determined.  相似文献   

12.
未胶结钙质砂静力和循环强度的单剪试验研究   总被引：1，自引：1，他引：0  
王晓丽  裴会敏  王栋 《海洋工程》2018,36(6):124-129
通过等体积的单调和循环单剪试验研究南海未胶结钙质砂的静、动力反应,讨论应力水平和相对密实度对钙质砂静、动力强度的影响,并与典型的石英砂性质进行比较。在单调单剪试验中,中密和密实钙质砂在100～400 k Pa范围的初始竖向应力下都表现出应变硬化的性质,有效内摩擦角随剪应变增大。在循环单剪试验中,钙质砂的反应与相对密实度和初始竖向应力密切相关,但中密和密实钙质砂中的等效孔压都能达到初始竖向应力的85%～90%,此时剪应变突增,试样发生破坏。与相近密实度的石英砂相比,钙质砂抵抗液化的能力更强。提出了南海钙质砂动强度的归一化表达式,建立了不排水静强度、不排水动强度和循环次数之间的关系。  相似文献   

13.
Based on the analytical solutions for wave-induced soil response in an unsaturated anisotropic seabed of finite thickness, an elliptical, i.e., noncircular rotation stress path is proven to be a more common state in a soil element with the cyclic shear stresses due to the traveling linear wave. The influence of an elliptical stress path on the characterization of failure strength is analyzed using three new parameters representing the shape, size, and the orientation of the ellipse. A series of cyclic rotational shear tests on the reconstituted specimens of Chinese Fujian Standard Sand have been performed to investigate the effect of elliptical stress path. A strength function in term of failure cycles is derived to quantify the failure strength of a given sand within a seabed subjected to regular wave loading. The results provide a basis for the evaluation of liquefaction potential of seabed but also point to a unique backbone cycle shear strength curve for soil under principal stress rotation.  相似文献   

14.
低围压水平下砂的排水行为(英文)   总被引：2，自引：1，他引：2  
采用干样沉降法制备样品 ,选用静三轴仪对松砂和密砂样在 10 k Pa至 10 0 k Pa的低围压下的排水行为进行了实验研究 ,并对实验结果作了橡皮膜校正 ,在围压为 10 k Pa的密砂实验中 ,轴向应力的校正值可达到 12 %。实验研究表明低围压下松砂的剪胀性非常明显 ,且存在剪应力极值 ;围压越低 ,松砂和密砂的剪应力极值越小 ,达到最大剪应力所对应的剪应变越小。同时还表明低围压范围内相对密度不同 ,砂的应力应变特性不同 ;此外 ,低围压下砂的内摩擦角高于高围压下的值 ,从而在工程上应重视低围压水平下砂土工程参数的合理选取  相似文献   

15.
The central Alborz mountain range, located in northern Iran, neighboring the Caspian Sea and where the two Persia and Eurasia plates meet, is known as a seismologically active area. In this regard, investigation of the behavior of saturated sand deposits located in this area may be of particular interest. Saturated sand deposits are subjected to instabilities owing to liquefaction or volume change due to earthquake shakings. A particular type of saturated sand deposits is Anzali sand which is abundant in Anzali port and other cities located in this area in northern Iran. This type of sand is a representative for most sands found in this area, i.e., the southern coastal line of Caspian Sea. This research is solely focused on the volume change behavior of marine deposits of Anzali area, often characterized as Anzali sand, in terms of the settlement of a model footing located on the surface of the sand by the aid of a transparent laminar shear box apparatus. Effects of a number of factors such as the frequency of the cyclic loading, the initial density of the sand, and the sample preparation method have been investigated. Observations indicated that the density index and the frequency of loading which are proportional to the energy of an earthquake have direct effects on the accumulation and amount of the final settlement of Anzali sand.  相似文献   

16.
A series of undrained monotonic triaxial compression tests were performed on natural, medium-dense (relative density (RD) = 50%) Chlef sand containing 0.5% of non-plastic fines, under different confining pressures of 50 kPa, 100 kPa, and 200 kPa. This article focuses on distinctive states of the monotonic undrained response of sands, namely the critical state, the phase transformation state, the quasi-steady state, and the state of undrained instability (onset of flow liquefaction). Specimens were prepared using dry funnel pluviation and wet deposition to investigate the effect of the initial sand fabric on these states. The present data suggest that the initial fabric of the sand appears to have a significant effect on the undrained behavior in the early stages of shearing, with its influence vanishing at large strains. Wet deposition specimens demonstrate considerably larger undrained instability state strength than their dry funnel pluviation counterparts, and a unique critical state locus is reached by both dry funnel pluviation and wet deposition.  相似文献   

17.
Model tests were conducted to investigate the behaviour of caisson breakwater resting on sand beds subject to impacts due to wave breaking. The centrifuge modelling technique was employed to simulate the prototype stress levels in the foundation soil as the behaviour of sand is highly stress dependent. A wave actuator was developed to simulate the wave-breaking impact loads on the caisson during centrifuge flight. The test results reveal that the vertical and horizontal movements and tilt of the caisson breakwater increase progressively with the number of breaking-wave impacts. The excess pore pressures developed in the foundation sand under non-reversal loading are generally small and appear insignificant. The results of the parametric studies conducted to examine the effects of impact-load pattern, caisson width, rock berm beneath caisson, wave slamming on top slab of caisson and cyclic preloading on the performance of caisson breakwater are also presented. The practical implications of the experimental findings in the present study are also highlighted in this paper.  相似文献   

18.
ABSTRACT

One-way cyclic loading is more typical for traffic loading and cyclic triaxial test has been recognized as a useful method for solving many engineering problems. Under traffic loading, the influence of variable confining pressure on cyclic behavior of natural organic clay subjected to cyclic traffic loading is rarely reported in the literature. In this study, a laboratory investigation on undrained cyclic behavior of natural organic clay is presented and conducted by cyclic triaxial apparatus. Tests are conducted by both constant confining pressure and variable confining pressure, to simulate the loading conditions induced by passing vehicles in actual engineering. Different stress levels are also considered in this study. By comparing between the results of constant confining pressure tests and variable confining pressure tests, it shows that the one-way cyclic behavior of organic clay is influenced significantly by variation of confining pressure, in terms of pore water pressure, permanent axial strain and stress–strain hysteretic loops.  相似文献   

19.
Abstract

This article presents a study of liquefaction resistance behaviour of sand using a cyclic triaxial test. The site investigation was performed, and frozen undisturbed specimens were taken from the Izumio site in Osaka, Japan. According to the evidence in 1995 Kobe Earthquake, the first two sand layers are vulnerable to undergo liquefaction. The effect of deviatoric stress on liquefaction resistance was focused on in this study. The excess pore pressure ratio, hysteresis loop, and effective stress path from the cyclic triaxial tests were reported. A multispring element model was employed to simulate the soil behaviour under cyclic loading. The results showed that applied deviatoric stress could influence the liquefaction resistance of sandy soil samples. The plots of the cyclic stress ratio versus the number of cycles to generate liquefaction known as a liquefaction resistance curve can be then constructed and compared with other sands.  相似文献   

20.
The behaviors of granular material and influencing factors under complex dynamic loading are studied by more and more researchers with particle flow method. Only the strain-controlled loading has been generally used in the current study, although this method was not consistent with the practice of engineering in many situations. In this article, stress-controlled dynamic simulation tests were carried out with particle flow method, which were used to study the collapse characteristics of silt under mutation of principal stress orientation. The tests were performed by PFC2D. The simulation results and the laboratory real tests’ results had a high degree of similarity, particularly in the collapse strain and vibration times. It was very useful to forecast the silt's critical failure state. Based on the verification data, the effects of confining pressure and cyclic shear stress ratio on the collapse characteristics of silt were studied further. With the increase of cyclic shear stress ratio, the deviator strain amplitude increased and the required vibration times gradually reduced to achieve the same strain level. Under the same dynamic shear stress ratio and vibration times, the initial dynamic elastic modulus slightly increased with the increase of initial confining pressure, and the variation range of final collapse deviator strain was small. In the analysis of micro-structural evolution, the redistribution of internal stress of sample was revealed during cyclic loading. With the increase of vibration times, the development of distribution gradually stabilized, and then the high shear stress appeared in some connected regions. On that stage, the particle system developed to instability and failure. The PFC simulation results confirmed that the collapse state was the critical stage to trigger the liquefaction of silt.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号