共查询到20条相似文献，搜索用时 375 毫秒
1.
The present paper is Part I of a series of three papers prepared by the authors on the methods useful for ultimate limit state assessment of marine structures, that have been developed in the literature during the last few decades. It is considered that such methods are now mature enough to enter day-by-day design and strength assessment practice. The aims of the three papers are to conduct some benchmark studies of such methods on ultimate limit state assessment of (unstiffened) plates, stiffened panels, and hull girders of ships and ship-shaped offshore structures, using some candidate methods such as ANSYS nonlinear finite element analysis (FEA), DNV PULS, ALPS/ULSAP, ALPS/HULL, and IACS common structural rules (CSR) methods. As an illustrative example, an AFRAMAX-class hypothetical double hull oil tanker structure designed by CSR method is studied. In the present paper (Part I), the ultimate limit state assessment of unstiffened plates under combined biaxial compression and lateral pressure loads is emphasized using ANSYS, DNV PULS, and ALPS/ULSAP methods, and their resulting computations are compared. Part II will deal with methods for the ultimate limit state assessment of stiffened panels under combined biaxial compression and lateral pressure using ANSYS, DNV PULS, and ALPS/ULSAP methods, and Part III will treat methods for the progressive collapse analysis of the hull structure using ANSYS, ALPS/HULL, and IACS CSR methods. 相似文献
2.
The present paper is Part II of a series of three papers on methods useful for the ultimate limit state assessment of ships and ship-shaped offshore structures. In contrast to Part I [Paik et al., 2007a. Methods for ultimate limit state assessment of ships and ship-shaped offshore structures: Part I unstiffened plates, Ocean Engineering, doi:10.1016/j.oceaneng.2007.08.004] that deals with unstiffened plates, the present paper (Part II) is focused on methods for the ultimate limit state assessment of stiffened plate structures under combined biaxial compression and lateral pressure actions. The object structure is the bottom part of an AFRAMAX-class hypothetical double-hull oil tanker structure designed by IACS common structural rules (CSR) method, that is the same ship studied in Part I. Three candidate methods, namely ANSYS nonlinear finite element method, DNV PULS method, and ALPS/ULSAP method, are employed for the present study. The results and insights developed from the present study are summarized in terms of ultimate strength characteristics of bottom-stiffened plate structures. 相似文献
3.
《中国海洋工程》2020,(4)
An investigation is conducted on the static ultimate limit state assessment of ship hull plates with elastically restrained edges subjected to axial compression. Both material and geometric non-linearities were considered in finite element(FE) analysis. The initial geometric imperfection of the plate was considered, while the residual stress introduced by welding was not considered. The ultimate strength of simply supported ship hull plates compared well with the existing empirical formula to validate the correctness of the applied boundary conditions, initial imperfection and mesh size. The extensive FE calculations on the ultimate strength of ship hull plates with elastically restrained edges are presented. Then a new simple empirical formula for plate ultimate strength is developed, which includes the effect of the rotational restraint stiffness, rotational restraint stiffness, and aspect ratios. By applying the new formula and FE method to ship hull plates in real ships, a good coincidence of the results between these two methods is obtained, which indicates that the new formula can accurately predict the ultimate strength of ship hull plates with elastically restrained edges. 相似文献
4.
Jeom Kee Paik Anil K. Thayamballi P. Terndrup Pedersen Young Il Park 《Ocean Engineering》2001,28(8):51
For a ship hull with large deck openings such as container vessels and some large bulk carriers, the analysis of warping stresses and hatch opening deformations is an essential part of ship structural analyses. It is thus of importance to better understand the ultimate torsional strength characteristics of ships with large hatch openings. The primary aim of the present study is to investigate the ultimate strength characteristics of ship hulls with large hatch openings under torsion. Axial (warping) as well as shear stresses are normally developed for thin-walled beams with open cross sections subjected to torsion. A procedure for calculating these stresses is briefly described. As an illustrative example, the distribution and magnitude of warping and shear stresses for a typical container vessel hull cross section under unit torsion is calculated by the procedure. By theoretical and numerical analyses, it is shown that the influence of torsion induced warping stresses on the ultimate hull girder bending strength is small for ductile hull materials while torsion induced shear stresses will of course reduce the ship hull ultimate bending moment. 相似文献
5.
It is well known that pitting corrosion occurring on surface of hull structural plate will surely result in a significant degradation of the ultimate strength of the hull structural plate. This report aims at development of an assessing formula for ultimate strength of hull plate with pitting corrosion damage under the biaxial in-plane compression loading. The ultimate strength assessment model that is in terms of the corroded volume loss was deduced in theory, and which was then completed through numerical experiment by employing nonlinear finite element analyses for series of corroded plate models. Meanwhile, pitting corrosion in actual ship hull was analyzed and simulated, which ensured that all the assumptions for the finite element model parameters were in accord with the actual hull plate with pitting corrosion damage. Furthermore, the effects of plate slenderness, the linear factors at the plate edges and the ratio between the transverse and the longitudinal in-plane stresses on the ultimate strength reduction related to the corroded volume loss were discussed. The ultimate strength assessment formula being in terms of corroded volume loss developed in this research is expected to be applicable to assess the ultimate strength of the hull structural plate with pitting corrosion damage. 相似文献
6.
大型集装箱船（LCS）具有较大的甲板开口，抗扭刚度非常低。在恶劣海况下航行时，大型集装箱船可能会遭遇斜浪的作用，此时船体将受到三向载荷的联合作用，水平波浪弯矩和扭转波浪弯矩可能会接近甚至超过垂向波浪弯矩，船体可能因发生组合变形而破坏。因此有必要研究大型集装箱船在三向载荷联合作用下的结构可靠性。在研究三向载荷联合作用下各维度极限强度的相互关系的基础上，提出了大型集装箱船的极限承载能力的可靠性评估方法，并对目标船在各浪向角下的结构可靠性进行评估。结果表明：目标船在0°浪向角下的失效概率最高；考虑水平波浪弯矩影响后目标船的结构可靠性有所降低；扭转波浪弯矩对目标船船中剖面的结构可靠性影响较小。 相似文献
7.
根据极限平衡和极限分析方法,首先建立了软土地基土体上海底管线的极限承载力计算公式.当地基处于极限状态时,基础作用于地基的全部荷载应等于该地基土体的承载能力,根据这一关系式可以推导出海底管线沉降量的计算公式.最后通过对试验结果的分析,证实所采用的计算方法是可行的. 相似文献
8.
防波堤风险分析研究框架 总被引：1，自引：0，他引：1
介绍了防波堤风险分析研究的内容、方法和目前的研究进展。防波堤风险分析包涵四个主要方面:防波堤风险辨识、防波堤风险估计、防波堤风险评价和防波堤风险控制。具体内容包括:防波堤系统正常使用极限状态和承载力极限状态的界定,波浪不确定性的识别和描述,防波堤失效模式的探讨,单一模式失效概率和系统失效概率的计算,两种极限状态失效后果的量化,成本-获益分析,效用分析,可接受风险准则和降低风险的措施。防波堤风险分析的目的在于为决策者明确工程中存在的诸多不确定性因素,提供充足信息,实现项目的决策优化。 相似文献
9.
A-man Zhang Ling-yu Zeng Xiao-da Cheng Shi-ping Wang Yu Chen 《Applied Ocean Research》2011,33(4):240-251
Whipping response will happen when a ship is subjected to underwater explosion bubble load. In that condition, the hull would be broken, and even the survivability will be completely lost. A calculation method on the dynamic bending moment of bubble has been put forward in this paper to evaluate the impact of underwater explosion bubble load on the longitudinal strength of surface ships. Meanwhile the prediction equation of bubble dynamic bending moment has been concluded with the results of numerical simulation. With wave effect taken into consideration, the evaluation method of the total damage of a ship has been established. The precision of this evaluation method has been proved through the comparison with calculation results. In order to verify the validity of the calculation results, experimental data of real ship explosion is applied. Prediction equation and evaluation method proposed in this paper are to be used in ship structure design, especially in the preliminary prediction of the ultimate withstanding capability of underwater explosion damage for the integrated ship in preliminary design phase. 相似文献
10.
Sang-Rai Cho Joonmo Choung Chang-Min Oh Kang-Su Lee Jung-Yeob Kim 《Ocean Engineering》2010,37(8-9):770-776
CSRs (Common Structural Rules for bulker and tanker), which came into effect in 2006, invoke the concept of the ultimate strength of hull girders. While numerous studies associated with the ultimate capacities regarding global hull girders and stiffened panels have been carried out, there are few application cases of the ultimate strengths for deck machineries and their supporting structures. In the present study, nonlinear finite element analyses have been performed to obtain ultimate capacities for a size 450 DIN type bollard including hull foundation structures for which elastic strength assessments based on allowable stress analyses were jointly carried out by a Mooring Fitting SWL Standardization Committee consisting of four major Korean shipbuilders (DSME, HHI, HHIC, and SHI) in 2003. The plastic hardening property is identified from a comparison of the results of ultimate strength simulations and a bollard tension tests performed by the committee. It is assumed that the ultimate load is the corresponding load point when the deformation slope of the bollard column reaches the critical slip angle. It is concluded that the reinforcements appear to be effective with respect to the allowable stress criterion, but are not substantially effective from the point of view of ultimate capacities. In other words, structural reinforcements based on allowable stress analyses may noticeably increase production costs, but do not remarkably raise the ultimate capacities. 相似文献
11.
为了研究桩长对海底防沉板—桩复合基础在水平、弯矩和扭转荷载作用下承载特性的影响,以我国南海水深200 m的某工程实例为研究对象,利用Flac3D有限差分仿真软件建立了计算模型。研究了桩长为4 m、6 m和8 m的防沉板—桩复合基础在水平、弯矩和扭转荷载作用下的极限承载力和荷载传递机理。结果表明,桩长超过6 m时复合基础的水平承载力显著增长,在水平加载过程中,防沉板总是先达到极限状态而破坏,桩基础的贡献在加载后期体现,且桩长为4 m、8 m时,桩基础与防沉板的连接处弯矩最大;随着桩长的增加,复合基础的抗弯承载力大幅提高,桩基础对复合基础的抗弯承载力贡献增大,当桩长超过8 m,桩长的增加对提高复合基础的抗弯承载力意义不大;在弯矩加载过程中,桩长对于防沉板、桩基础的荷载分配有显著影响,桩长为4 m时,外荷载主要由防沉板承担,当桩长超过4 m时,外荷载主要由桩基础承担;当扭转荷载不超过2 100 k N·m时,防沉板承担主要荷载,直至防沉板达到极限状态而发生旋转,随后桩基础的承载力逐渐发挥;对于桩长为6 m、8 m的复合基础,其极限状态根据防沉板适用性准则确定。 相似文献
12.
为了研究循环载荷作用下扶强材初始损伤对其极限强度的影响,进行了14组扶强材的循环加载试验和分析。构造了考虑材料累积损伤完整、断筋和大变形的扶强材单元极限承载力计算公式,提出了相应循环载荷作用下损伤扶强材单元的端缩曲线表达式和船体梁极限强度计算的简化逐步破坏法。编制了循环载荷作用下船体梁损伤极限强度计算程序,进行了船体梁极限强度计算,并与有限元结果进行对比。研究结果表明：改进的损伤扶强材模型可较为准确地描述扶强材材料损伤的完整、断筋和大变形的极限承载力退化情况,扶强材腹板断裂的损伤相较初始大变形及材料累积损伤形式承载力下降程度更明显;所提出的循环载荷作用下损伤船体梁极限强度计算的简化逐步迭代方法,能定量地计算扶强材在不同类型损伤下的极限承载力退化程度,具有较高精度,方便易行,可应用于工程设计。 相似文献
13.
《中国海洋工程》2016,(6)
This paper presents a series of monotonically combined lateral loading tests to investigate the bearing capacity of the MSCs(modified suction caissons) in the saturated marine fine sand. The lateral loads were applied under load- and displacement-controlled methods at the loading eccentricity ratios of 1.5, 2.0 and 2.5. Results show that, in the displacement-controlled test, the deflection-softening behavior of load-deflection curves for MSCs was observed, and the softening degree of the load-deflection response increased with the increasing external skirt length or the decreasing loading eccentricity. It was also found that the rotation center of the MSC at failure determined by the load-controlled method is slightly lower than that by the displacement-controlled method. The calculated MSC capacity based on the rotation center position in serviceability limit state is relatively conservative, compared with the calculated capacity based on the rotation center position in the ultimate limit state. In the limit state, the passive earth pressures opposite the loading direction under load- and displacement-controlled methods decrease by 46% and 74% corresponding to peak values, respectively; however, the passive earth pressures in the loading direction at failure only decrease by approximately 3% and 7%, compared with their peak values. 相似文献
14.
为了快速并有效地计算海洋平台等薄壁箱型梁结构的约束扭转极限承载能力,进行了薄壁梁约束扭转极限承载能力简化计算方法研究.基于塑性极限状态分析理论,提出了薄壁梁约束扭转极限状态应力分布假设,将薄壁梁视作为一系列由主要支撑构件和扶强材支撑的板格,推导了薄壁梁约束扭转极限承载能力上限的计算公式.应用非线性有限元方法验证了所提假设和计算公式的精度,将所提方法应用于箱型梁模型和半潜平台的约束扭转极限承载能力的计算分析,并与非线性有限元结果进行了比对,结果表明,本方法具有较高的精度,可用于海洋平台等薄壁梁的扭转极限承载力上限的估算. 相似文献
15.
This paper presents a series of monotonically combined lateral loading tests to investigate the bearing capacity of the MSCs (modified suction caissons) in the saturated marine fine sand. The lateral loads were applied under load- and displacement-controlled methods at the loading eccentricity ratios of 1.5, 2.0 and 2.5. Results show that, in the displacement-controlled test, the deflection-softening behavior of load-deflection curves for MSCs was observed, and the softening degree of the load-deflection response increased with the increasing external skirt length or the decreasing loading eccentricity. It was also found that the rotation center of the MSC at failure determined by the load-controlled method is slightly lower than that by the displacement-controlled method. The calculated MSC capacity based on the rotation center position in serviceability limit state is relatively conservative, compared with the calculated capacity based on the rotation center position in the ultimate limit state. In the limit state, the passive earth pressures opposite the loading direction under load- and displacement-controlled methods decrease by 46% and 74% corresponding to peak values, respectively; however, the passive earth pressures in the loading direction at failure only decrease by approximately 3% and 7%, compared with their peak values. 相似文献
16.
在环境条件和使用荷载作用下,高桩码头结构损伤和承载力降低是普遍存在的问题。在役梁板式高桩码头结构安全评估,是保证港口设施安全运行的必要措施。结构整体可靠度是结构安全评估的核心指标,但目前尚未建立结构整体可靠度计算的有效方法。基于非线性有限元数值模型,采用蒙特卡罗模拟技术确定了典型梁板式高桩码头结构整体极限承载力概率分布模型及其统计参数,研究了损伤位置、损伤程度和损伤数量等对极限承载力概率分布及其统计参数的影响,明确了无损结构整体极限承载力概率分布模型及其统计参数可用于损伤结构分析。将结构整体极限承载力作为结构抗力随机变量,采用一次二阶矩法计算结构的可靠指标,建立了一种在役梁板式高桩码头结构整体可靠度计算的有效方法。 相似文献
17.
V.I. BeenaV.Anantha Subramanian 《Ocean Engineering》2003,30(9):1077-1106
This paper reports seakeeping studies performed on a parametrically varied set of SWATH hull forms. The SWATH form, because of its de-linked nature of design affords many variations of the underwater hull geometry without affecting overall deck length and beam. For a given displacement, the hull form can be varied in terms of length, basic section shape, maximum area of cross section of under water hull and strut water plane shape. Using these variants, a parametric family of hull forms has been generated employing Chebychev polynomial scheme for representing sectional area distribution and using a bi-quintic B-spline based surface definition scheme. Not all designs offer optimal performance in a given sea state. A twin-hull motion analysis program SEDOS has been used to study the motions and other dynamic effects. Setting criteria for operability, these dynamic effects have been quantified into a single value namely, operability index. The approach here fulfils an investigation at the design stage in order to tap the full advantage of the SWATH form. The study brings out a methodology for assessment of the SWATH at the design stage highlighting interesting results related to section shapes and sectional area distribution. Thus, combining a newly developed interactive surface generation scheme with an analysis package, a rapid assessment tool is offered for new design. 相似文献
18.
Corrosion and fatigue cracks are major threats to the structural integrity of aging offshore platforms.For the rational estimation of the safety levels of aging platforms,a global reliability assessment approach for aging offshore platforms with corrosion and fatigue cracks is presented in this paper.The base shear capacity is taken as the global ultimate strength of the offshore plaffoms,it is modeled as a random process that decreases with time in the presence of corrosion and fatigue crack propagation.And the corrosion and fatigue crack growth rates in the main members and key joints are modeled as random variables.A simulation method of the extreme wave loads which are applied to the structures of offshore platforms is proposed too.Furthermore,the statistics of global base shear capacity and extreme wave loads are obtained by Monte Carlo simulation method.On the basis of the limit state equation of global failure mode,the instantaneous reliability and time dependent reliability assessment methods are both presented in this paper.Finally the instantaueous reliability index and time dependent failure probability of a jacket platform are estimated with different ages in the demonstration example. 相似文献
19.
Marine propellers usually operate in a spatially nonuniform wake and then the propeller exciting forces are produced. These exciting forces will cause serious hull vibration and noise radiation. So, there are many researches on the exciting forces of propellers. However, the effects of the shaft and blade elasticity are ignored in most studies. Therefore, firstly, considered the effects of the shaft and blade elasticity, a fluid–structure interaction dynamic model of the fluid-propeller-shaft system is established by coupled BEM and FEM. Then, based on this model, the characteristics of axial exciting force and theirs transmission mechanism to the hull via the shaft are studied. The research results show that first, there are two kinds of vibration modes for blade bending vibration: global mode and local mode. The elastic coupling effect between the blade and the shafting only affects the global mode, but hardly affects the local mode of the blade. Secondly, during the transmission of axial exciting force to the hull through the blades and shafting, only the global mode of the blades can amplify it, while the local mode cannot. These studies could provide a guideline for the optimal design of the propeller-shaft system to make the exciting force transmitted to the ship hull via the shafting be the smallest. 相似文献
20.
1 .IntroductionThe large-diameter cylindrical structure for coastal and offshore engineering has been widely usedin China .Thistype of structureis composed of a steel or reinforced concrete cylindrical thin-wall shellplaced partlyintothe ground by a speci… 相似文献