共查询到20条相似文献，搜索用时 375 毫秒
1.
A decision methodology for the management of seismic risk of a single building is presented. The decision criterion aims at minimizing the expected life‐cycle cost, including the initial cost of the design and the expected cost of damage due to future earthquakes. The expected life‐cycle cost of each design alternative is formulated using a renewal model for the occurrence of earthquakes in a seismic source, which accounts for the temporal dependence between the occurrence of ‘characteristic’ earthquakes. The formulation involves the expected damage cost from an earthquake of specified magnitude in a given source. This term is estimated by simulating the processes of fault rupture, elastic wave propagation, surface soil amplification, dynamic structural response and generation of damage costs. As an example, the methodology is applied to an actual office building in Tokyo. A simple decision problem between two design alternatives is set: a bare steel moment frame, and the same frame equipped with oil dampers. Through this case study, the installation of the oil dampers is demonstrated to be effective in reducing the life‐cycle cost of the building under consideration. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
2.
Bridge design should take into account not only safety and functionality, but also the cost effectiveness of investments throughout a bridge life‐cycle. This paper presents a probabilistic approach to compute the life‐cycle cost (LCC) of corroding reinforced concrete (RC) bridges in earthquake‐prone regions. The approach is developed by combining cumulative seismic damage and damage associated with corrosion due to environmental conditions. Cumulative seismic damage is obtained from a low‐cycle fatigue analysis. Chloride‐induced corrosion of steel reinforcement is computed based on Fick's second law of diffusion. The proposed methodology accounts for the uncertainties in the ground motion parameters, the distance from the source, the seismic demand on the bridge, and the corrosion initiation time. The statistics of the accumulated damage and the cost of repairs throughout the bridge life‐cycle are obtained by Monte‐Carlo simulation. As an illustration of the proposed approach, the effects of design parameters on the LCC of an example RC bridge are studied. The results are valuable in better estimating the condition of existing bridges and, therefore, can help to schedule inspection and maintenance programs. In addition, by taking into consideration the two deterioration processes over a bridge life‐cycle, it is possible to estimate the optimal design parameters by minimizing, for example, the expected cost throughout the life of the structure. A comparison between the effects of the two deterioration processes shows that, in seismic regions, the cumulative seismic damage affects the reliability of bridges over time more than the corrosion even for corrosive environments. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
3.
A fully automated design methodology based on nonlinear response history analysis is proposed for the optimum seismic design of reinforced concrete (RC) structures. The conventional trial‐and‐error process is replaced by a structural optimization algorithm that serves as a search engine capable of locating the most efficient design in terms of cost and performance. Two variations of the proposed design methodology are introduced. The first approach treats the optimum design problem in a deterministic manner, while in the second variation the optimum design is sought in the framework of a reliability‐based optimization problem. The reliability‐based approach seems to be a more rational procedure since more meaningful design criteria that correlate better with the performance‐based design concept can be adopted. Thus, the practice of using the mean annual frequency of a limit‐state being exceeded to assess the candidate designs is compared with the use of deterministic criteria. Both formulations take into consideration the structural response for a number of limit‐states, from serviceability to collapse prevention. The proposed design procedure is specifically tailored to the design of RC structures, where a preliminary design step of generating tables of concrete sections is introduced. In order to handle the large size of the tables, the concept of multi‐database cascade optimization is implemented. The final design has to comply with the provisions of European design codes. The proposed methodology allows for a significant reduction of the direct construction cost combined with improved control of the seismic performance under earthquake loading. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
4.
The assessment of seismic design codes has been the subject of intensive research work in an effort to reveal weak points that originated from the limitations in predicting with acceptable precision the response of the structures under moderate or severe earthquakes. The objective of this work is to evaluate the European seismic design code, i.e. the Eurocode 8 (EC8), when used for the design of 3D reinforced concrete buildings, versus a performance‐based design (PBD) procedure, in the framework of a multi‐objective optimization concept. The initial construction cost and the maximum interstorey drift for the 10/50 hazard level are the two objectives considered for the formulation of the multi‐objective optimization problem. The solution of such optimization problems is represented by the Pareto front curve which is the geometric locus of all Pareto optimum solutions. Limit‐state fragility curves for selected designs, taken from the Pareto front curves of the EC8 and PBD formulations, are developed for assessing the two seismic design procedures. Through this comparison it was found that a linear analysis in conjunction with the behaviour factor q of EC8 cannot capture the nonlinear behaviour of an RC structure. Consequently the corrected EC8 Pareto front curve, using the nonlinear static procedure, differs significantly with regard to the corresponding Pareto front obtained according to EC8. Furthermore, similar designs, with respect to the initial construction cost, obtained through the EC8 and PBD formulations were found to exhibit different maximum interstorey drift and limit‐state fragility curves. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
5.
Passive structural control techniques are generally used as seismic rehabilitation and retrofit methodologies for existing structures. A poorly explored and exciting opportunity within structural seismic control research is represented by the possibility to design new structural forms and configurations, such as slender buildings, without compromising the structural performance through an integrated design approach. In this paper, with reference to viscous dampers, an integrated seismic design procedure of the elastic stiffness resources and viscoelastic properties of a dissipative bracing‐damper system is proposed and developed to ensure a seismic design performance, within the displacement‐based seismic design, explicitly taking into account the dynamic behaviour both of the structural and control systems. The optimal integrated seismic design is defined as the combination of the variables that minimizes a suitable index, representing an optimized objective function. Numerical examples of the proposed integrated cost‐effectiveness seismic design approach both on an equivalent SDOF system and a proportionally damped MDOF integrated system are developed defining the design variables, which minimize the cost index. Validation of the effectiveness of the proposed integrated design procedure is carried out by evaluating the average displacement of the time‐history responses to seven unscaled acceleration records selected according to EC8 provisions. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
6.
A risk‐based life cycle cost strategy for optimal design and evaluation of control methods for nonlinear structures 
下载免费PDF全文
下载免费PDF全文 The lack of direct correspondence between control objectives and hazard risks over the lifetime of systems is a key shortcoming of current control techniques. This along with the inability to objectively analyze the benefits and costs of control solutions compared with conventional methods has hindered widespread application of control systems in seismic regions. To address these gaps, this paper offers 2 new contributions. First, it introduces risk‐based life cycle–cost (LCC) optimal control algorithms, where LCC is incorporated as the performance objective in the control design. Two strategies called risk‐based linear quadratic regulator and unconstrained risk‐based regulator are subsequently proposed. The considered costs include the initial cost of the structure and control system, LCC of maintenance, and probabilistically derived estimates of seismic‐induced repair costs and losses associated with downtime, injuries, and casualties throughout the life of the structure. This risk‐based framework accounts for uncertainties in both system properties and hazard excitations and uses outcrossing rate theory to estimate fragilities for various damage states. The second contribution of this work is a risk‐based probabilistic framework for LCC analysis of existing and proposed control strategies. The proposed control designs are applied to the nonlinear model of a 4‐story building subjected to seismic excitations. Results show that these control methods reduce the LCC of the structure significantly compared with the status quo option (benefits of up to $1 351 000). The advancements offered in this paper enhance the cost‐effectiveness of control systems and objectively showcase their benefits for risk‐informed decision making. 相似文献
7.
Existing loading protocols for quasi-static cyclic testing of structures are based on recordings from regions of high seismicity. For regions of low to moderate seismicity they overestimate imposed cumulative damage demands. Since structural capacities are a function of demand, existing loading protocols applied to specimens representative of structures in low to moderate seismicity regions might underestimate structural strength and deformation capacity. To overcome this problem, this paper deals with the development of cyclic loading protocols for European regions of low to moderate seismicity. Cumulative damage demands imposed by a set of 60 ground motion records are evaluated for a wide variety of SDOF systems that reflect the fundamental properties of a large portion of the existing building stock. The ground motions are representative of the seismic hazard level corresponding to a 2 % probability of exceedance in 50 years in a European moderate seismicity region. To meet the calculated cumulative damage demands, loading protocols for different structural types and vibration periods are developed. For comparison, cumulative seismic demands are also calculated for existing protocols and a set of records that was used in a previous study on loading protocols for regions of high seismicity. The median cumulative demands for regions of low to moderate seismicity are significantly less than those of existing protocols and records of high seismicity regions. For regions of low to moderate seismicity the new protocols might therefore result in larger strength and deformation capacities and hence in more cost-effective structural configurations or less expensive retrofit measures. 相似文献
8.
Conventional design methodology for the earthquake‐resistant structures is based on the concept of ensuring ‘no collapse’ during the most severe earthquake event. This methodology does not envisage the possibility of continuous damage accumulation during several not‐so‐severe earthquake events, as may be the case in the areas of moderate to high seismicity, particularly when it is economically infeasible to carry out repairs after damaging events. As a result, the structure may collapse or may necessitate large scale repairs much before the design life of the structure is over. This study considers the use of design force ratio (DFR) spectrum for taking an informed decision on the extent to which yield strength levels should be raised to avoid such a scenario. DFR spectrum gives the ratios by which the yield strength levels of single‐degree‐of‐freedom oscillators of different initial periods should be increased in order to limit the total damage caused by all earthquake events during the lifetime to a specified level. The DFR spectra are compared for three different seismicity models in case of elasto‐plastic oscillators: one corresponding to the exponential distribution for return periods of large events and the other two corresponding to the lognormal and Weibull distributions. It is shown through numerical study for a hypothetical seismic region that the use of simple exponential model may be acceptable only for small values of the seismic gap length. For moderately large to large seismic gap lengths, it may be conservative to use the lognormal model, while the Weibull model may be assumed for very large seismic gap lengths. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
9.
Performance‐based seismic design (PBSD) can be considered as the coupling of expected levels of ground motion with desired levels of structural performance, with the objective of achieving greater control over earthquake‐induced losses. Eurocode 8 (EC8) already envisages two design levels of motion, for no collapse and damage limitation performance targets, anchored to recommended return periods of 475 and 95 years, respectively. For PBSD the earthquake actions need to be presented in ways that are appropriate to the estimation of inelastic displacements, since these provide an effective control on damage at different limit states. The adequacy of current earthquake actions in EC8 are reviewed from this perspective and areas requiring additional development are identified. The implications of these representations of the seismic loads, in terms of mapping and zonation, are discussed. The current practice of defining the loading levels on the basis of the pre‐selected return periods is challenged, and ideas are discussed for calibrating the loading‐performance levels for design on the basis of quantitative earthquake loss estimation. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
10.
Past earthquake experiences indicate that most buildings designed in accordance with modern seismic design codes could survive moderate‐to‐strong earthquakes; however, the financial loss due to repairing cost and the subsequent business interruption can be unacceptable. Designing building structures to meet desired performance targets has become a clear direction in future seismic design practice. As a matter of fact, the performance of buildings is affected by structural as well as non‐structural components, and involves numerous uncertainties. Therefore, appropriate probabilistic approach taking into account structural and non‐structural damages is required. This paper presents a fuzzy–random model for the performance reliability analysis of RC framed structures considering both structural and non‐structural damages. The limit state for each performance level is defined as an interval of inter‐storey drift ratios concerning, respectively, the non‐structural and structural damage with a membership function, while the relative importance of the two aspects is reflected through the use of an appropriate cost function. To illustrate the methodology, herein the non‐structural damage is represented by infill masonry walls. The probabilistic drift limits for RC components and masonry walls from the associated studies are employed to facilitate the demonstration of the proposed model in an example case study. The results are compared with those obtained using classical reliability model based on single‐threshold performance definition. The proposed model provides a good basis for incorporating different aspects into the performance assessment of a building system. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
11.
A new methodology for seismic design is proposed based on structural optimization with performance‐based constraints. Performance‐based criteria are introduced for the seismic design of new buildings. These criteria are derived from the National Guidelines for Seismic Rehabilitation of Buildings (Reference [19], Federal Emergency Management Agency (FEMA), ‘NHERP Guidelines for seismic rehabilitation of buildings’, Report Nos 273 and 274, Washington, DC, 1997) for retrofitting existing structures. The proposed design methodology takes into account the non‐linear behaviour of the structure. The goal is to incorporate in the design the actual performance levels of the structure, i.e. how much reserve capacity the structure has in an earthquake of a given magnitude. The optimal design of the structure minimizes the structural cost subjected to performance constraints on plastic rotations of beams and columns, as well as behavioural constraints for reinforced concrete frames. Uncertainties in the structural period and in the earthquake excitation are taken into account using convex models. The optimization routine incorporates a non‐linear analysis program and the procedure is automated. The proposed methodology leads to a structural design for which the levels of reliability (performance levels) are assumed to be quantifiable. Furthermore, the entire behaviour of the structure well into the non‐linear range is investigated in the design process. Copyright © 2000 John Wiley & Sons, Ltd. 相似文献
12.
Development and assessment of damage‐to‐loss models for moment‐frame reinforced concrete buildings 下载免费PDF全文
下载免费PDF全文 Luís Martins Vítor Silva Mário Marques Helen Crowley Raimundo Delgado 《地震工程与结构动力学》2016,45(5):797-817
The assessment of earthquake loss often requires the definition of a relation between a measure of damage and a quantity of loss, usually achieved through the employment of a damage‐to‐loss model. These models are frequently characterized by a large variability, which inevitably increases the uncertainty in the vulnerability assessment and earthquake loss estimation. This study provides an insight on the development of damage‐to‐loss functions for moment‐frame reinforced concrete buildings through an analytical methodology. Tri‐dimensional finite element models of existing reinforced concrete buildings were subjected to a number of ground motion records compatible with the seismicity in the region of interest, through nonlinear dynamic analysis. These results were used to assess, for a number of damage states, the probability distribution of loss ratio, taking into consideration member damage and different repair techniques, as well as to derive sets of fragility functions. Then, a vulnerability model (in terms of the ratio of cost of repair to cost of replacement, conditional on the level of ground shaking intensity) was derived and compared with the vulnerability functions obtained through the combination of various damage‐to‐loss models with the set of fragility functions developed herein. In order to provide realistic estimates of economic losses due to seismic action, a comprehensive study on repair costs using current Portuguese market values was also carried out. The results of this study highlight important issues in the derivation of vulnerability functions, which are a fundamental component for an adequate seismic risk assessment. © 2015 The Authors. Earthquake Engineering & Structural Dynamics published by John Wiley & Sons Ltd. 相似文献
13.
Design spectrum (DS) model is typically specified in a seismic code of practice for structural design. In a region of low-to-moderate seismicity where seismic code does not exist, a DS model in a well established code of practice is usually adopted, while the suitability of such model has seldom been evaluated. In this article, the elastic DS models for reference (rock) site stipulated in six major codes of practice (AS1170.4–2007, EN1998-1:2004, GB50011–2010, IBC–2012, NBCC–2010 and NZS1170.5:2004) have been compared and scrutinized. Three cities of low-to-moderate seismicity, namely, Melbourne (Australia), Hong Kong (China) and Karlsruhe (Germany), have been selected for illustrative purposes. Particular emphasis has been put on the parameterization scheme for DS model. It is found that huge discrepancies (over 100%) exist among the models, especially at the long period range, due to differences in spectral shapes and the recommended corner periods, which would lead to undesirable effects on the use of the displacement-based seismic design approach. It is urged that the values of corner periods should be determined specifically and cautiously based on the regional seismicity pattern and local geological conditions. 相似文献
14.
For the first time after the finalisation of the European Norm for seismic design of buildings (Eurocode 8 – EC8),the performance of RC buildings designed with this code is evaluated through systematic nonlinear analyses. Regular 4-, 8- or 12-storey RC frames are designed for a PGA of 0.2 or 0.4 g and to one of the three alternative ductility classes in EC8. As the Eurocodes are meant to replace soon existing national codes, design and performance is also compared to that of similar frames designed with the 2000 Greek national codes. The performance of alternative designs under the life-safety (475 years) and the damage limitation (95 years) earthquakes is evaluated through nonlinear seismic response analyses. The large difference in material quantities and detailing of the alternative designs does not translate into large differences in performance. Design for either Ductility Class High (H) or Medium (M) of EC8 is much more cost-effective than design for Ductility Class Low (L), even in moderate seismicity. It is also much more cost-effective than design to the 2000 Greek national codes. 相似文献
15.
The local design and construction practices in the United Arab Emirates(UAE),together with Dubai’s unique rate of development,warrant special attention to the selection of Lateral Force-Resisting Systems(LFRS).This research proposes four different feasible solutions for the selection of the LFRS for tall buildings and quantifies the impact of these selections on seismic performance and cost.The systems considered are: Steel Special Moment-Resisting Frame(SMRF),Concrete SMRF,Steel Dual System(SMRF with Special Steel Plates Shear Wall,SPSW),and Concrete Dual System(SMRF with Special Concrete Shear Wall,SCSW).The LFRS selection is driven by seismic setup as well as the adopted design and construction practices in Dubai.It is found that the concrete design alternatives are consistently less expensive than their steel counterparts.The steel dual system is expected to have the least damage based on its relatively lesser interstory drifts.However,this preferred performance comes at a higher initial construction cost.Conversely,the steel SMRF system is expected to have the most damage and associated repair cost due to its excessive flexibility.The two concrete alternatives are expected to have relatively moderate damage and repair costs in addition to their lesser initial construction cost. 相似文献
16.
It has been well documented that following a major earthquake a substantial percentage of economic loss results from downtime of essential lifelines in and out of major urban centres. This has thus led to an improvement of both performance‐based seismic design philosophies and to the development of cost‐effective seismic structural systems capable of guaranteeing a high level of protection, low structural damage and reduced downtime after a design‐level seismic event. An example of such technology is the development of unbonded post‐tensioned techniques in combination with rocking–dissipating connections. In this contribution, further advances in the development of high‐performance seismic‐resistant bridge piers are achieved through the experimental validation of unbonded post‐tensioned bridge piers with external, fully replaceable, mild steel hysteretic dissipaters. The experimental response of three 1 : 3 scale unbonded, post‐tensioned cantilever bridge piers, subjected to quasi‐static and pseudo‐dynamic loading protocols, are presented and compared with an equivalently reinforced monolithic benchmark. Minimal physical damage is observed for the post‐tensioned systems, which exhibit very stable energy dissipation and re‐centring properties. Furthermore, the external dissipaters can be easily replaced if severely damaged under a major (higher than expected) earthquake event. Thus, negligible residual deformations, limited repair costs and downtime can be achieved for critical lifeline components. Satisfactory analytical–experimental comparisons are also presented as a further confirmation of the reliability of the design procedure and of the modelling techniques. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
17.
While structural engineers have traditionally focused on individual components (bridges, for example) of transportation networks for design, retrofit, and analysis, it has become increasingly apparent that the economic costs to society after extreme earthquake events are caused at least as much from indirect costs as direct costs due to individual structures. This paper describes an improved methodology for developing probabilistic estimates of repair costs and repair times that can be used for evaluating the performance of new bridge design options and existing bridges in preparation for the next major earthquake. The proposed approach in this paper is an improvement on previous bridge loss modeling studies—it is based on the local linearization of the dependence between repair quantities and damage states so that the resulting model follows a linear relationship between damage states and repair points. The methodology uses the concept of performance groups (PGs) that account for damage and repair of individual bridge components and subassemblies. The method is validated using two simple examples that compare the proposed method to simulation and previous methods based on loss models using a power–law relationship between repair quantities and damage. In addition, an illustration of the method is provided for a complete study on the performance of a common five‐span overpass bridge structure in California. Intensity‐dependent repair cost ratios (RCRs) and repair times are calculated using the proposed approach, as well as plots that show the disaggregation of repair cost by repair quantity and by PG. This provides the decision maker with a higher fidelity of data when evaluating the contribution of different bridge components to the performance of the bridge system, where performance is evaluated in terms of repair costs and repair times rather than traditional engineering quantities such as displacements and stresses. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
18.
Probabilistic economic seismic loss estimation in steel buildings using post‐tensioned moment‐resisting frames and viscous dampers 下载免费PDF全文
下载免费PDF全文 Athanasios I. Dimopoulos Angelos S. Tzimas Theodore L. Karavasilis Dimitrios Vamvatsikos 《地震工程与结构动力学》2016,45(11):1725-1741
The potential of post‐tensioned self‐centering moment‐resisting frames (SC‐MRFs) and viscous dampers to reduce the economic seismic losses in steel buildings is evaluated. The evaluation is based on a prototype steel building designed using four different seismic‐resistant frames: (i) conventional moment resisting frames (MRFs); (ii) MRFs with viscous dampers; (iii) SC‐MRFs; or (iv) SC‐MRFs with viscous dampers. All frames are designed according to Eurocode 8 and have the same column/beam cross sections and similar periods of vibration. Viscous dampers are designed to reduce the peak story drift under the design basis earthquake (DBE) from 1.8% to 1.2%. Losses are estimated by developing vulnerability functions according to the FEMA P‐58 methodology, which considers uncertainties in earthquake ground motion, structural response, and repair costs. Both the probability of collapse and the probability of demolition because of excessive residual story drifts are taken into account. Incremental dynamic analyses are conducted using models capable to simulate all limit states up to collapse. A parametric study on the effect of the residual story drift threshold beyond which is less expensive to rebuild a structure than to repair is also conducted. It is shown that viscous dampers are more effective than post‐tensioning for seismic intensities equal or lower than the maximum considered earthquake (MCE). Post‐tensioning is effective in reducing repair costs only for seismic intensities higher than the DBE. The paper also highlights the effectiveness of combining post‐tensioning and supplemental viscous damping by showing that the SC‐MRF with viscous dampers achieves significant repair cost reductions compared to the conventional MRF. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
19.
A multi‐objective optimization procedure is presented for designing steel moment resisting frame buildings within a performance‐based seismic design framework. Life cycle costs are considered by treating the initial material costs and lifetime seismic damage costs as two separate objectives. Practical design/construction complexity, important but difficult to be included in initial cost analysis, is taken into due account by a proposed diversity index as another objective. Structural members are selected from a database of commercially available wide flange steel sections. Current seismic design criteria (AISC‐LRFD seismic provisions and 1997 NEHRP provisions) are used to check the validity of any design alternative. Seismic performance, in terms of the maximum inter‐storey drift ratio, of a code‐verified design is evaluated using an equivalent single‐degree‐of‐freedom system obtained through a static pushover analysis of the original multi‐degree‐of‐freedom frame building. A simple genetic algorithm code is used to find a Pareto optimal design set. A numerical example of designing a five‐storey perimeter steel frame building is provided using the proposed procedure. It is found that a wide range of valid design alternatives exists, from which a decision maker selects the one that balances different objectives in the most preferred way. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
20.
According to the most modern trend, performance‐based seismic design is aimed at the evaluation of the seismic structural reliability defined as the mean annual frequency (MAF) of exceeding a threshold level of damage, i.e. a limit state. The methodology for the evaluation of the MAF of exceeding a limit state is herein applied with reference to concentrically ‘V’‐braced steel frames designed according to different criteria. In particular, two design approaches are examined. The first approach corresponds to the provisions suggested by Eurocode 8 (prEN 1998—Eurocode 8: design of structures for earthquake resistance. Part 1: general rules, seismic actions and rules for buildings), while the second approach is based on a rigorous application of capacity design criteria aiming at the control of the failure mode (J. Earthquake Eng. 2008; 12 :1246–1266; J. Earthquake Eng. 2008; 12 :728–759). The aim of the presented work is to focus on the seismic reliability obtained through these design methodologies. The probabilistic performance evaluation is based on an appropriate combination of probabilistic seismic hazard analysis, probabilistic seismic demand analysis (PSDA) and probabilistic seismic capacity analysis. Regarding PSDA, nonlinear dynamic analyses have been carried out in order to obtain the parameters describing the probability distribution laws of demand, conditioned to given values of the earthquake intensity measure. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献