共查询到20条相似文献，搜索用时 62 毫秒
1.
钱塘江河口围涂对杭州湾风暴潮影响数值模拟 总被引：1，自引：1，他引：1
应用二维水动力模式Mike21对钱塘江河口治江围涂对杭州湾风暴潮的影响进行了数值模拟。首先采用概化地形做了围涂对风暴潮影响的主要因素分析,然后采用实际地形计算极端工况和百年一遇工况条件下已有围涂前后风暴潮的变化,最后对今后规划围涂所造成的影响进行了预测。结果表明,围涂引起的平面边界改变是影响杭州湾风暴潮的主要因素,围涂引起的地形抬升的影响是次要因素;已有围涂使杭州湾极端风暴高潮位抬升1.85~0.09 m,抬升幅度由湾顶向湾口递减;规划围涂后,杭州湾风暴高潮位总体抬升,抬升值最大的湾中部为0.25 m。 相似文献
2.
杭州湾跨海大桥对钱塘江河口水流的影响 总被引：1，自引：0，他引：1
通过河工模型试验,研究建设在潮汐河口的特大型桥梁——杭州湾跨海大桥对水环境产生的影响。杭州湾跨海大桥河工模型上边界选在老盐仓,下边界定在金山,平面比尺为1000,铅直比尺为100,模拟总水域面积约2200km2;模型运用2000年9月杭州湾实测水下地形及大范围同步水文测验资料进行了验证,其精度较高。在此基础上,结合实测资料分析,运用定床模型试验对杭州湾跨海大桥建成后附近水域流态的变化及对钱塘江涌潮、上游行洪等的影响进行了分析和预测。建桥前后潮位、流速流向、潮流量以及涌潮高度等试验数据的变化表明,杭州湾跨海大桥建成后对钱塘江河口水流的影响主要在桥位近区,对涌潮、上游行洪基本没有影响。 相似文献
3.
本文根据钱塘江河口和杭州湾内滩涂演变特性和初步确定的尖山河段治导线,提出促淤围涂70万亩的规划方案。总投资8.74亿元,平均1200元/亩。初步分析表明,经济效益较好。 相似文献
4.
5.
近50 a来杭州湾冲淤变化规律与机制研究 总被引：6，自引：4，他引：2
使用杭州湾1959-2010年的水下地形图, 结合过去数十年来长江入海水沙量和钱塘江河口段冲淤变化状况, 分析了近50 a来杭州湾在长江入海泥沙量锐减和治江围涂等人类活动作用下的冲淤变化规律及其物理机理。结果表明, 乍浦以上区域近50 a来处于较显著的淤积状态, 且有自上向下发展的趋势, 这种淤积主要是由于钱塘江河口治江缩窄工程所引起的;湾内地形发生了局部调整, 部分小型潮流槽脊系统趋于消亡, 地形趋于平坦化, 湾口北部2003年以后有转淤为冲的趋势, 这与长江入海泥沙量锐减和该区域围垦工程等因素有关;1959-2003和2003-2010年两个时段, 湾内泥沙淤积的年平均值分别为0.91×108和1.66×108 m3。对于整个钱塘江河口系统而言, 即自杭州湾湾口至钱塘江河口段的闸口断面, 长江入海泥沙量减少所产生的影响尚不明显, 2003年以后泥沙淤积速率甚至有所上升。杭州湾近50 a的冲淤变化是人为强烈干预下的大流域-河口系统响应与中小流域-河口系统响应的调整结果。 相似文献
6.
杭州湾潮汐特征时空变化及原因分析 总被引：2，自引：2，他引：0
杭州湾是世界著名的强潮河口湾,一直是研究的热点。基于杭州湾口内外实测潮汐资料,对杭州湾潮汐特征及时空变化进行了系统分析,包括高潮位、低潮位、平均潮位、潮差、涨潮历时以及天文潮变化,同时分析了20世纪80年代以来潮汐特征变化的原因。结果表明:最近50年来,杭州湾年平均高潮位和海平面抬高,潮差增大;澉浦年平均低潮位抬高,涨潮历时缩短,浅海分潮增大;钱塘江河口治江缩窄是造成杭州湾潮汐变化的主要因素;浙江和邻近海域的涉海工程可能是造成浙江沿海海平面上升的主要原因之一。 相似文献
7.
利用水龄理论的新方法,借助环境水动力学模型定量讨论了多年平均径流条件下长江河口径流和潮汐作用对河口水流输运时间的影响。研究给出了长江河口水流输运时间的时空格局:多年平均流量条件下,水流从徐六泾输出至河口(122.5°E)大约需要24d,南、北槽分流口以上河段水流输运时间主要由径流控制,水流输运时间为8d,向下至拦门沙滩顶水域由径流和潮汐共同控制,水龄为16d,说明最大浑浊带区域的水流输运速度较上下游为慢,从一个侧面阐述了最大浑浊带区域水动力的特征;长江河口水流输运时间存在明显的层化现象,表底层相差最大值可达6d。数值模拟试验结果表明长江河口的潮汐作用是影响河口水流输运时间的关键要素,河口巨大的进潮量增强河口水流交换能力并减小水流输运时间,从而显著影响随水体运动的物质输运格局。水流输运时间研究,不仅可以成功应用于河口水动力环境的量化研究,而且可以为泥沙输运及污染物输运等环境变化研究提供动力的基础。 相似文献
8.
杭州湾的三维水流数值模拟 总被引：2，自引：1，他引：2
建立了一个基于σ变换和内外模式分裂技术三维水流数学模型，采用有限节点法（平面）和变步长差分法（σ向）对方程进行了离散；通过风生流和环岛水流两个理论模式对所建模型进行了校验，并将该模型应用到杭州湾的三维水流数值模拟中，效果良好，所建模型垂向分辨率高，简单实用，可应用于河口，海岸，湖泊等大范围水域的水流数值计算。 相似文献
9.
钱塘江河口及杭州湾总面积5000多平方公里,位居浙江省北部。其开发治理对浙江经济发展影响颇大。为适应对外开放形势,今后钱塘江和杭州湾的开发治理将密切注意港口航道资源开发,适度围垦滩涂作为发展港口工业和创汇农业用地。同时仍需注意加固沿岸堤防和改善泄洪,排涝条件,以保障两岸生命财产安全和稳定现有工农业生产发展。从而,对于钱塘江河口及杭州湾开发治理将由单一的防御型转向综合开发型,并以取得社会、经济和环境三者的最大综合效益作为目标。 相似文献
10.
采用实测资料分析、潮浪水槽试验、定床模型试验以及已建桥梁对涌潮影响的现场观测等手段,研究了钱塘江下游尖山河段建桥对涌潮景观的影响。研究结果表明,钱塘江河口的喇叭形河湾和庞大的水下沙坎使潮波能量积聚、潮差增大,水深急剧变浅、潮波剧烈变形是形成钱塘江涌潮的主要原因。影响涌潮的主要因素是潮汐、江道地形和治江围涂工程,而建桥不会影响涌潮产生的条件,但由于桥墩的阻水作用,对桥上游500 m范围内的涌潮形态有所影响;当采用合理的桥台设计方案,即阻水面积较小时,对上游涌潮高度的影响仅3 cm左右,故不会影响涌潮的景观。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
13.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
14.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
20.