共查询到20条相似文献，搜索用时 62 毫秒
1.
Shear behaviour of the joints formed by the interface of two different material types, such as rock and cemented paste backfill, rock and concrete or two different rock types, have practical importance in many rock engineering activities. This paper presents the results of an experimental investigation into the shear behaviour of these special joints under pseudo-static shear velocity. Direct shear tests on concrete–plaster interfaces were carried out under boundary conditions of constant normal load and constant normal stiffness. Shearing velocities of the performed tests were in the range of 0.3–30 mm/min. The results of the shear tests conducted on the planar and rough artificial prepared joints showed that the shearing velocity has a significant influence on the shear strength, friction angle and shear stiffness of the hard–soft material interface. So that, these parameters were decreased when shear velocity was increased. Also, comparison of the tests results that performed on the concrete–plaster joints with those from tests on the plaster–plaster and concrete–concrete interfaces showed that the shear behaviour of concrete–plaster interface is governed mainly by the shear parameters of the plaster block (namely softer material). 相似文献
2.
The variation of the shear strength of infilled rock joints under cyclic loading and constant normal stiffness conditions is studied. To simulate the joints, triangular asperities inclined at angles of 9.5° and 18.5° to the shear movement were cast using high-strength gypsum plaster and infilled with clayey sand. These joints were sheared cyclically under constant normal stiffness conditions. It was found that, for a particular normal stiffness, the shear strength is a function of the initial normal stress, initial asperity angle, joint surface friction angle, infill thickness, infill friction angle, loading direction and number of loading cycles. Based on the experimental results, a mathematical model is proposed to evaluate the shear strength of infilled rock joints in cyclic loading conditions. The proposed model takes into consideration different initial asperity angles, initial normal stresses and ratios of infill thickness to asperity height. 相似文献
3.
Shear behaviour of regular sawtooth rock joints produced from casting plaster are investigated under constant normal stiffness (CNS) conditions. Test results obtained in this investigation are also compared with the constant normal load (CNL) tests. It is observed that the peak shear stress obtained under CNL conditions always underestimates the peak shear stress corresponding to the CNS condition. Plots of shear stress against normal stress show that a nonlinear (curved) strength envelope is acceptable for soft rock joints subjected to a CNS condition, in comparison with the linear or bilinear envelopes often proposed for a CNL condition. Models proposed by Patton (1966) and Barton (1973) have also been considered for the predictions of peak shear stress of soft joints under CNS conditions. Although Patton's model is appropriate for low asperity angles, it overestimates the shear strength in the low to medium normal stress range at higher asperity angles. In contrast, while Barton's model is realistic for the CNL condition, it seems to be inappropriate for modelling the shear behaviour of soft joints under CNS conditions. The effect of infill material on the shear behaviour of the model joints is also investigated, and it is found that a small thickness of bentonite infill reduces the peak stress significantly. The peak shear stress almost approached that of the shear strength of infill when the infill thickness to asperity height ratio (t/a) reached 1.40. This paper also introduces an original, empirical shear strength envelope to account for the change in normal stress and surface degradation during CNS shearing. © Rapid Science Ltd. 1998 相似文献
4.
微震、工程爆破等低应力循环剪切荷载作用对节理岩体工程失稳破坏具有重要影响。为研究峰前循环剪切加卸载作用下岩石节理剪切力学特性,采用RDS-200型岩石节理剪切试验系统对人工劈裂黄砂岩节理进行了峰前循环剪切下的直剪试验。通过与未进行峰前循环剪切加卸载时岩石节理力学参数预测值对比,得到峰前循环剪切加卸载作用对峰前剪切刚度、峰值剪切强度、峰值剪切位移与残余剪切强度的影响。结果表明：（1）峰前循环剪切加卸载后,当法向应力为2 MPa时,岩石节理峰前剪切刚度增大,当法向应力为4～10 MPa时,岩石节理峰前剪切刚度在循环剪切应力幅值范围内增大,在超出循环剪切应力幅值时减小;（2）峰前循环剪切加卸载后,峰值剪切强度降低了10%～20%,降低百分比随法向应力增大整体呈对数函数增大;峰值剪切位移增加了2%～40%,增加百分比随法向应力增大整体呈对数函数减小;（3）峰前循环剪切加卸载后,岩石节理残余剪切强度无明显变化,峰值剪切强度与残余剪切强度差值减小,峰后剪切应力做功损失百分比降低。 相似文献
5.
The subject under investigation is the strength of a single shear plane which exhibits a regular, asymmetric roughness pattern. In the shear direction the asperities are so steeply inclined that the joint becomes mechanically non-effective with the result that the asperities are sheared off. Against the shear direction the asperities are only gently inclined. It is shown that this particular roughness pattern is of some general importance in geomechanics (examples: unconfined compression test; shear plane with secondary fractures). Simple analytical considerations allow the formulation of a shear criterion, which is dependent on friction angle øm and cohesioncm of the intact rock and on the inclination γ of the gently inclined parts of the asperities which are dipping against the shear direction. In the Mohr-diagram the criterion results in envelopes which converge at high normal stresses against the envelope of intact rock. Furthermore, the criterion expresses that both the slope of the envelopes and the dilation angle continuously decrease with increasing normal stress. Therefore the criterion adequately describes features which are regarded as most important when shearing rough joints or compound shear surfaces. 相似文献
6.
Numerous studies have been made to improve Barton's shear strength model for the quantification of rock joints. However, in these previous studies, the roughness and shear strength of the rock joint have been underestimated especially for relatively high undulated profiles (joint roughness coefficient (JRC) >14). The main factors of roughness underestimation in rough rock joints are investigated for the proper quantification of rock joint roughness. The aliasing effect and the roughness characteristics are analyzed by using artificial joint profiles and natural rock joint profiles. A 3D camera scanner is adopted to verify the main source of underestimation when using conventional measurement methods. Shear strength tests are carried out by using two types of shear apparatus to study the roughness mobilization characteristics, which may also affect the roughness underestimation. The results of joint roughness assessment, such as aliasing and undulation of waviness, show that the roughness can be underestimated in relatively rough joint profiles (JRC>14). At least two components of roughness parameters are needed to properly represent the joint roughness, for example, the amplitude and the inclination angle of joint asperity. Roughness mobilization is affected by both the normal stress and the asperity scale. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
7.
节理在固定法向压力刚度（CNS）条件下的剪切过程比较复杂,剪切中由于剪胀的存在使得法向压力增大,而法向压力的增加又限制了剪胀的发生。根据CNS剪切过程中某一瞬时状态下法向压应力大小,以节理在该法向压应力下法向剪胀位移与剪切位移的关系为基础,建立一个楔形物理模型。通过循环迭代求得CNS剪切过程中每一步的法向压应力值,进而得到整个过程的剪切应力值。通过该模型,讨论了节理各参数对CNS剪切过程的影响,结果表明,其剪切应力值受法向压应力刚度与节理法向变形参数共同协调控制（包括单轴压缩变形及剪胀角的磨损）,节理在剪切过程中越不易发生压缩变形,其剪切应力值越大。 相似文献
8.
The present study explores the degradation characteristics and scale of unevenness (small-scale roughness) on sheared rock joint surfaces at a low-stress regime. While the degradation characteristics of unevenness and the normal stress are mutually interrelated, an understanding of the degradation patterns of the three-dimensional roughness of rock joints is one of the important components needed to identify asperity failure characteristics and to quantify the role of damaged unevenness in establishing a shear strength model. A series of direct shear tests was performed on three-dimensional artificial rock joint surfaces at different normal stress levels. After shearing, the spatial distributions and statistical parameters of degraded roughness were analysed for the different normal stress levels. The length and area of the degraded zones showed bell-shaped distributions in a logarithmic scale, and the dominant scale (or the most frequently occurring scale) of the damaged asperities (i.e., unevenness) ranged from approximately, 0.5 to 5.0 mm in length and 0.1–10 mm 2 in area. This scale of the damaged unevenness was consistent regardless of the level of normal stress. It was also found that the relative area of damaged unevenness on a given joint area, and thus the contribution of the mechanical asperity failure component to shear strength increased as normal stress increased. 相似文献
9.
Shear failure of rockmass along a weak plane occurs frequently in rock slopes and in underground tunnels. To study the shear behaviour and acoustic emission (AE) characteristics of joints under different experimental conditions (asperity height, shear rate, and normal load), irregular artificial saw-tooth joints with different asperity heights were sheared in the laboratory, and the AE signals were detected and analysed. The results demonstrated that the strength of the joints increased with increases in normal load and asperity height, while the strength of the joints first increased and then decreased when the shear rate was elevated. The ideal curve of the cumulative hits could be divided into a quiet period, a slow rise period, and a sharp growth period, which could be used to monitor and predict the potential shear failure of the joints. The higher the asperity was, the higher the peak energy rate and the lower the peak hit rate, and cumulative hits at failure were because of differences in asperity size and number. The peak hit rate and cumulative energy tended to increase gradually with the decrease in shear rate, and the minimum peak hit rate and energy rate at failure were both attained at the maximum shear rate. In addition, curves of the energy rate and hit rate showed large fluctuations at higher shear rates. The peak energy rate and cumulative energy under low normal stress could be greater than the peak energy rate and cumulative energy under high normal stress, and the peak hit rate and cumulative hit number under high normal stress could be larger than that of under low normal stress. 相似文献
10.
为研究不同边界条件下剪切速率对岩石节理剪切力学特性的影响,采用RDS-200型岩石节理剪切试验系统对人工浇筑的具有相同节理形貌的不规则水泥节理试样进行了常法向应力和常法向刚度2种边界条件下5种剪切速率的直剪试验。结果表明：（1）常法向应力边界条件下,随剪切速率增大,相同法向应力下的类岩石节理峰前剪切刚度减速增大,峰值剪切强度和残余剪切强度呈对数降低;随剪切速率增大,类岩石节理黏聚力减速增大,内摩擦角呈对数降低。（2）常法向刚度边界条件下,随剪切速率增大,相同法向应力的类岩石节理峰前剪切刚度减速增大,峰值剪切强度呈对数降低,较高法向应力下的残余剪切强度先增大后减小;随剪切速率增大,类岩石节理黏聚力呈对数降低,内摩擦角减速增大。（3）与常法向应力边界条件相比,常法向刚度条件下,节理黏聚力平均增加了115.85%,内摩擦角平均降低了8.44%;相同初始法向应力和剪切速率下,峰前剪切刚度、峰值剪切强度和残余剪切强度分别平均增加了11.96%、19.47%和32.32%,峰值法向位移平均降低了40.12%。该研究结论可为不同剪切速率下地表和地下工程岩体节理的剪切失稳评价提供一定参考。 相似文献
11.
Barton, N., 1973. Review of a new shear-strength criterion for rock joints. Eng. Geol., 7: 287–332. The surface roughness of rock joints depends on their mode of origin, and on the mineralogy of the rock. Amongst the roughest joints will be those that formed in intrusive rocks in a tensile brittle manner, and amongst the smoothest the planar cleavage surface in slates. The range of friction angles exhibited by this spectrum will vary from about 75° or 80° down to 20° or 25°, the maximum values being very dependent on the normal stress, due to the strongly curved nature of the peak strength envelopes for rough unfilled joints. Direct shear tests performed on model tension fractures have provided a very realistic picture of the behaviour of unfilled joints at the roughest end of the joint spectrum. The peak shear strength of rough—undulating joints such as tension surfaces can now be predicted with acceptable accuracy from a knowledge of only one parameter, namely the effective joint wall compressive strength or JCS value. For an unweathered joint this will be simply the unconfined compression strength of the unweathered rock. However in most cases joint walls will be weathered to some degree. Methods of estimating the strength of the weathered rock are discussed. The predicted values of shear strength compare favourably with experimental results reported in the literature, both for weathered and unweathered rough joints. The shear strength of unfilled joints of intermediate roughness presents a problem since at present there is insufficient detailed reporting of test results. In an effort to remedy this situation, a simple roughness classification method has been devised which has a sliding scale of roughness. The curvature of the proposed strength envelopes reduces as the roughness coefficient reduces, and also varies with the strength of the weathered joint wall or unweathered rock, whichever is relevant. Values of the Coulomb parameters c and Φ fitted to the curves between the commonly used normal stress range of 5–20 kg/cm2 appear to agree quite closely with experimental results. The presence of water is found in practice to reduce the shear strength of rough unfilled joints but hardly to affect the strength of planar surfaces. This surprising experimental result is also predicted by the proposed criterion for peak strength. The shear strength depends on the compressive strength which is itself reduced by the presence of water. The sliding scale of roughness incorporates a reduced contribution from the compressive strength as the joint roughness reduces. Based on the same model, it is possible to draw an interesting analogy between the effects of weathering, saturation, time to failure, and scale, on the shear strength of non-planar joints. Increasing these parameters causes a reduction in the compressive strength of the rock, and hence a reduction in the peak shear strength. Rough—undulating joints are most affected and smooth—nearly planar joints least of all. 相似文献
12.
Summary A conceptual model for the behaviour of rock joints during cyclic shear and under constant normal stresses was proposed according to results from shear tests with 50 concrete replicas of rock joints. The shear strength and deformability of joint samples were found to be both anisotropic and stress dependent. Based on these experimental results, a two-dimensional constitutive model was developed for rock joints undergoing monotonic or cyclic loading sequences. The joint model was formulated in the framework of non-associated plasticity, coupled with empirical relations representing the surface roughness degradation, appearance of peak and residual shear stresses, different rates of dilatancy and contraction, variable normal stiffness with normal deformation, and dependence of shear strength and deformability on the normal stress. The second law of thermodynamics was represented by an inequality and used to restrict the values of some of the material parameters in the joint model. The new joint model was implemented into a two-dimensional Distinct Element Method Code, UDEC, and its predictions agreed well with some well-known test results. 相似文献
13.
Most natural rock masses contain a large number of random joints and fissures, and most of the rock masses at the rock engineering are commonly in both compression and shear stress environment. However, the research on the failure characteristics of complex random jointed rock mass under compressive-shear loading is still limited. To address this gap, this paper uses the particle flow code 2D to establish a discrete fractured rock mass model and carry out a series of numerical tests with different compressive-shear angles (α) and different joint geometric parameters. The effects of compressive-shear angle and joint geometric parameters on the strength and failure characteristics of fractured rock masses are studied. The results indicate that with the increase of α, the peak strength of the specimen decreases gradually, and the failure mode changes from the composite shear failure mode (Mode-I) to a plane shear failure mode (Mode-II) and then to intact shear failure mode (Mode-III). Specifically, the three failure modes occur in the specimens with α?=?15°, 30° or 45°, 60°, respectively. The existence of joints affects stress distribution on rock mass during the loading process. Furthermore, the stress at the joint tip is relatively concentrated, while on both sides of the joint is smaller. Three kinds of crack coalescence patterns are observed: tensile, shear, and tensile-shear mixed coalescence. The inclination angle of the rock bridge between adjacent joints affects the specific type of coalescence. 相似文献
14.
The paper presents a new microplane constitutive model for the inelastic behavior of jointed rock masses that takes into account the mechanical behavior and geometric characteristics of cracks and joints. The basic idea is that the microplane modeling of rock masses under general triaxial loading, including compression, requires the isotropic rock matrix and the joints to be considered as two distinct phases coupled in parallel. A joint continuity factor is defined as a microplane damage variable to represent the stress‐carrying area fraction of the joint phase. Based on the assumption of parallel coupling between the rock joint and the rock matrix, the overall mechanical behavior of the rock is characterized by microplane constitutive laws for the rock matrix and for the rock joints, along with an evolution law for the microplane joint continuity factor. The inelastic response of the rock matrix and the rock joints is controlled on the microplane level by the stress–strain boundaries. Based on the arguments enunciated in developing the new microplane model M7 for concrete, the previously used volumetric–deviatoric splits of the elastic strains and of the tensile boundary are avoided. The boundaries are tensile normal, compressive normal, and shear. The numerical simulations demonstrate satisfactory fits of published triaxial test data on sandstone and on jointed plaster mortar, including quintessential features such as the strain softening and dilatancy under low confining pressure, as well as the brittle–ductile transition under higher confining pressure, and the decrease of jointed rock strength and Young's modulus with an increasing dip angle of the joint. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
15.
通过RMT－150C电伺服试验机,利用人工浇注素混凝土节理试样进行了不同剪切变形速率、法向应力和起伏角情况下的剪切试验,研究了节理破坏模式和刚度特征及其与起伏角、剪切变形速率和法向应力之间的关系。研究结果表明,试样破坏模式主要受起伏角控制,小起伏角情况下节理呈现磨损破坏模式,大起伏角情况下节理呈现剪断破坏模式,法向应力和剪切变形速率对节理破坏模式有一定的影响;节理的剪切刚度随剪切变形速率和起伏角的增大而增大,增大幅度随变形速率的增大有减小趋势;节理的剪切刚度随法向应力的增大而增大,基本呈线性关系。提出了考虑剪切速率和起伏角度影响的节理剪切刚度公式,并根据试验结果对剪切刚度公式进行了拟合。 相似文献
16.
The morpho‐mechanical behaviour of one artificial granite joint with hammered surfaces, one artificial regularly undulated joint and one natural schist joint was studied. The hammered granite joints underwent 5 cycles of direct shear under 3 normal stress levels ranging between 0.3 and 4 MPa. The regularly undulated joint underwent 10 cycles of shear under 6 normal stress levels ranging between 0.5 and 5 MPa and the natural schist replicas underwent a monotonics shear under 5 normal stress levels ranging between 0.4 and 2.4 MPa. These direct shear tests were performed using a new computer‐controlled 3D‐shear apparatus. To characterize the morphology evolution of the sheared joints, a laser sensor profilometer was used to perform surface data measurements prior to and after each shear test. Based on a new characterization of joint surface roughness viewed as a combination of primary and secondary roughness and termed by the joint surface roughness, SR s, one parameter termed ‘joint surface degradation’, Dw, has been defined to quantify the degradation of the sheared joints. Examinations of SR s and Dw prior to and after shearing indicate that the hammered surfaces are more damaged than the two other surfaces. The peak strength of hammered joint with zero‐dilatancy, therefore, significantly differs from the classical formulation of dilatant joint strength. An attempt has been made to model the peak strength of hammered joint surfaces and dilatant joints with regard to their surface degradation in the course of shearing and two peak strength criteria are proposed. Input parameters are initial morphology and initial surface roughness. For the hammered surfaces, the degradation mechanism is dominant over the phenomenon of dilatancy, whereas for a dilatant joint both mechanisms are present. A comparison between the proposed models and the experimental results indicates a relatively good agreement. In particular, compared to the well‐known shear strength criteria of Ladanyi and Archambault or Saeb, these classical criteria significantly underestimate and overestimate the observed peak strength, respectively, under low and high normal stress levels. In addition and based on our experimental investigations, we put forward a model to predict the evolution of joint morphology and the degree of degradation during the course of shearing. Degradations of the artificial undulated joint and the natural schist joint enable us to verify the proposed model with a relatively good agreement. Finally, the model of Ladanyi and Archambault dealing with the proportion of total joint area sheared through asperities, as, once again, tends to underestimate the observed degradation. Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
17.
利用规则的小尺寸锯齿构造二阶起伏体,对不同二阶起伏体高度的人工节理进行常法向应力下的直剪试验,研究了节理剪切力学特性。对节理的剪切强度、变形特征进行了分析,并对破坏特征做出解释。试验结果表明：二阶起伏体对节理剪切力学特性有重要影响,含二阶起伏体节理的剪切力学特性与只含有一阶起伏体节理的剪切力学特性不同,只含一阶起伏体的节理剪应力只有一个峰值,含二阶起伏体的节理会出现波浪状的剪胀曲线和多峰值剪应力,且峰值剪应力随剪切位移增大依次出现并逐个减小;随着二阶起伏体高度增大,节理峰值剪切强度增大,节理依次出现磨损破坏、多次性剪断破坏、一次性剪断破坏。 相似文献
18.
A new constitutive model to describe the shear behavior of rock joints under constant normal stiffness (CNS) and constant normal load (CNL) conditions is proposed. The model was developed using an empirical approach based on the results of a total of 362 direct shear tests on tensile fractured rock joints and replicas of tensile joints and on a new quantitative roughness parameter. This parameter, the active roughness coefficient C r, is derived from the features of the effective roughness mobilized at the contact areas during shearing. The model involves a shear strength criterion and the relations between stresses and displacements in the normal and shear directions, where the effects of the boundary conditions and joint properties are considered by the shape indices C d and C f. The model can be used to predict the shear behavior under CNS as well as CNL conditions. The shear behavior obtained from the experimental results is generally in good agreement with that estimated by the proposed model, and the effects of joint roughness, initial normal stress, and normal stiffness are reasonably reflected in the model. 相似文献
19.
An intensive investigation was set up to study the mechanical response of discontinuities with different joint wall compressive strengths. Physical models were employed in order to perform the planned studies. Models were designed to contain profiles of regular artificial joints molded by five types of plaster mortars each of which representing a distinct uniaxial compressive strength. The compressive strengths of plaster specimens ranged from 5.9 to 19.5 MPa. These specimens were prepared considering to have discontinuities of regular triangular asperity profile and were so designed to achieve joint walls of different strength material combinations. Direct shear tests were carried out on joints, and variations of shear stiffness, normal stiffness, and residual friction angle were investigated in various states. Details of the experiments, obtained data, the performed analyses, and the results are presented in this paper. 相似文献
20.
An elasto-plastic constitutive model is introduced for rock joints under cyclic loading, considering the additional shear resistance generated by the asperity damage in the first forward shear cycle and sliding mechanism for further shearing. A series of cyclic loading direct shear tests was conducted on artificial joints with triangular asperities and replicas of a real rock asperity surface under constant normal stiffness (CNS) conditions. The model was calibrated and then validated using selected data sets from the experimental results. Model simulations were found to be in good agreement with the rock joints behaviour under cyclic loading and CNS conditions both in stress prediction and dilation behaviour. In addition, dynamic stability analysis of an underground structure was carried out, using Universal Distinct Element Code and the proposed constitutive model. 相似文献
|
