共查询到20条相似文献，搜索用时 52 毫秒
1.
水力压裂作为一种主要的地热能开采手段,其压裂效果除与岩体基本物理力学性质有关外,还与裂隙分布、地应力状态、压裂工程参数等密切相关.为了探究以上因素对水力压裂过程中裂缝扩展行为的影响,以冀中坳陷碳酸盐岩储层岩体为研究对象,基于扩展有限元法,建立裂缝扩展流固耦合模型,分析了水平应力差、射孔方位角、注入液排量和压裂液黏度等参数对裂缝扩展行为的影响.结果表明:单裂缝扩展时,射孔方位角越小、注入量越大、越有利于裂缝扩展;双裂缝扩展时,水平应力差增大,裂缝偏转程度变小;水力裂缝与天然裂缝相交时,较小水平应力差有利于天然裂缝开启. 相似文献
2.
裂隙的剪胀特性及扩展演化规律对岩体的渗流特性具有重要影响。为揭示裂隙剪胀及扩展演化对岩体渗流的影响,基于残余强度提出了一种能较好描述岩石硬化-软化特性的全剪切本构关系;结合剪切变形与裂隙开度的关系,利用最小势能原理和立方定律,建立了压剪作用下考虑裂隙剪胀特性的渗流应力耦合模型;假定压剪作用下裂隙发生Ⅰ型扩展,提出了伴有翼型裂纹的渗流模型,该模型不仅考虑了岩石的剪胀特性,更反映了裂隙扩展过程渗流的演化规律。对不同裂隙粗糙度的剪切应力-位移曲线进行分析,全剪切本构模型表现出较高的拟合精度。在剪切应力-位移关系基础上,通过剪切渗流试验数据对压剪作用下渗流模型进行验证,结果表明,该模型能较好地描述岩体剪胀阶段渗透性演化规律。利用等效裂隙简化裂隙网络,并通过试验数据进行验证,证实了裂隙扩展过程渗流-应力耦合模型的准确性与适用性。 相似文献
3.
利用自主研发的煤岩剪切细观试验装置,以砂岩为研究对象,开展了不同饱和度数条件下的岩石剪切细观开裂演化与贯通机制试验研究,分析了砂岩剪切细观开裂演化过程和贯通机制,探讨了饱水系数对细观开裂和裂纹形态特征的影响。研究结果表明：剪切过程中,伴随着应力降,裂纹一般首先出现在剪切面中部,几条裂纹间断分布,距离较近的裂纹相互连通形成大裂纹,在应力继续下降的一瞬间,各裂纹连通形成贯通面;水的弱化作用影响了岩石的强度,使得试件底部出现较大的次级裂纹;饱水系数越大,分叉裂纹越多,使得试件的表面裂纹形态更加复杂,断裂面弯折段的数目越多,下端部次级裂纹越发育,整体损伤范围越大;细观上,局部独立裂纹贯通过程伴随着胶结颗粒岩桥的梁式旋转和弯曲折断,水的弱化作用,使得岩桥内部和外部微裂纹增多;随着饱水系数的增加,岩石剪切过程中出现的独立和次级裂纹的数目均呈增加趋势。 相似文献
4.
坡体内不同部位结构面间岩桥断裂扩展导致了反倾层状岩坡的破坏。为研究坡体内非贯通性裂缝断裂扩展对坡体演化的控制作用,以苗尾水电站右坝肩倾倒变形体为地质原型,开展含多组非贯通性裂缝的反倾层状岩质边坡离心模型试验,分析反倾层状岩质边坡内非贯通性裂缝变形特性。结果表明:（1）坡体内含非贯通性裂缝的岩层断裂最终呈现为裂缝间岩桥贯通、缓倾裂缝与上岩层贯通、陡倾裂缝与下岩层贯通、陡倾裂缝与缓倾裂缝端口处贯通及非裂缝处岩层发生断裂等5类裂缝断裂模式,并以裂缝间岩桥贯通为主要断裂模式;（2）基于断裂力学并结合裂缝断裂叠加原理,主折断面处岩层的不稳定系数在坡高1/3处最小,并向坡脚和坡顶两侧逐渐变大,而应力强度因子由坡高1/3处向坡脚和坡顶处逐渐变小;（3）裂缝的断裂扩展控制着坡体演化,并受裂纹率及裂缝周围的尖端应力场影响较大。在坡体演化初期,以坡体后缘压缩沉降和局部岩层裂缝压剪破坏为主,岩层倾角发生较大变化,呈现由坡体上部往下逐级变大的趋势;演化中期,坡体后缘裂缝扩展形成主折断面,坡体中上部岩层角度变化较大,裂缝断裂数目的继续增加;演化末期,裂缝断裂数目保持平稳,主要以断裂岩层的位置重分布为主要变形特征,次级折断面形成,破碎岩层之间进一步被压缩,坡体进一步发生失稳破坏。 相似文献
5.
Open Fissure Folds hosted by high pressure/low temperature metamorphic rocks of south Evia (Greece) are introduced, their structural and microstructural record is analysed, and a mechanical model is proposed. Open Fissure Folds are preserved as at least two parallel folded quartz–feldspar veins separated by narrow buckled rock columns. The veins originated as tensile cracks that propagated in the middle crust driven by high differential stress. Features diagnostic for Open Fissure Folds indicate that the rock columns represented the layers of high viscosity, and not the veins as consistently reported in many previous studies on folded veins. This record is taken to indicate that buckling of the rock columns initiated after arrest of the fractures and terminated prior to complete vein sealing. Accordingly, mechanical decoupling by open fissures allowed for buckling of the rock columns in response to episodic creep of the host rocks according to stress relaxation, as expected for postseismic deformation in the earthquake cycle. I propose that the parental fractures propagated in response to quasi-instantaneous coseismic loading of the middle crust. Buckling was attributed to transient postseismic creep and stress relaxation. Complete sealing of the veins occurred when stresses were largely relaxed. Each Open Fissure Fold records the stress and strain history of a single earthquake. 相似文献
6.
We have examined microstructures, mineralogical composition, geochemical alteration, and texture of four selected fault rock samples from the Deep Geodynamical Laboratory (DGLab) Gulf of Corinth project using optical microscopy, cathodoluminescence microscopy (CL), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and synchrotron X-ray diffraction measurements. The fault core is composed of red and gray clayey gouge material and surrounded by a damage zone of brecciated limestones. Pressure solution features, calcite veins and calcite clasts in the breccia and gouge material attest the presence of paleo-fluids and fluid-driven mass transfer during deformation. Differences in CL-colors between the matrix and calcite vein cement and inside the vein cement suggest repeated infiltration of fluids with different composition from various sources (formation water and meteoric water). Twin lamellae densities estimated in calcite veins are used as paleo-piezometer. The deduced differential stress is ∼140 ± 70 MPa for the older vein generation and appears to be higher than stress for the youngest veins (45 ± 23 MPa). In spite of the relatively small clay content in both samples, newly formed clay minerals have been observed in gray as well as red clayey gouge material. Differences between gray and red clay gouge material are found in fault rock composition, porosity and clay fabric. The proportion of chlorite in the red gouge is significantly less than that in the gray gouge whereas the initial porosity is significantly higher than in the gray gouge material. The detection of a well-oriented clay fabric in red clay gouge samples is unique in comparison to other major fault zones. 相似文献
7.
在冻融条件下岩石微裂隙中的水发生相变,体积膨胀,对微裂隙产生很大的冻胀力,当冻胀力超过岩石的抗拉强度时,微裂隙扩展。温度升高时,水又进入新的微裂隙,如此反复循环造成了岩石的损伤。据此,将岩石中的微裂隙等效为扁平状椭圆裂隙,基于断裂力学建立了单条微裂隙下裂隙扩展长度与冻胀力的关系,考虑岩石中微裂隙的分布,将岩石冻融条件下的应变分解为初始损伤应变、附加损伤应变和塑性应变,建立了弹塑性冻融损伤本构模型。最后,通过岩石冻融试验对该模型的合理性进行了验证,结果表明,该模型能够较好地模拟岩石在不同冻融次数下的应力-应变关系曲线。 相似文献
8.
Fracturing of rocks is simulated using an electronic computer, on the assumption that when a stress acts on a model, the fracturing condition is determined according to Mohr's theory and that of Griffith. A rock body is regarded as an aggregate of a grid cell whose strength is expressed by a random number of Gaussian distribution functions and the layered fabric of the rock body is given by inserting layered parts with different strength and with various inclinations. The results displaying the fractures on the grid system suggest that some of the geologic structures such as the echelon or the zigzag pattern of fracture are ascribed to fracturing in a layered or heterogeneous body, and variation of strength and the presence of layered fabric in a rock have a significant influence on fracture patterns developed in the rock. 相似文献
9.
为了揭示薄层状岩体单层厚度对裂纹扩展路径的影响,利用ABAQUS软件进行数值模拟,对含预制裂纹的不同单层厚度的层状岩体进行三点弯曲数值试验,岩体试样长度和宽度一定（512 mm×128 mm）,分5种不同的单层厚度建模,单层厚度分别为:64 mm、32 mm、16 mm、8 mm、4 mm。提取破裂过程中的声发射信息及主裂纹路径参数,对比分析不同层理厚度时,岩体的峰值载荷、声发射事件数、累计声发射事件数、主裂纹长度等对单层厚度的变化规律。研究结果表明:（1）薄层状岩体的强度与单层厚度有一定关系,单层厚度越大,岩体的抗弯强度越小,并且这种变化是非线性的。（2）在不同层厚条件下,层理面均表现出了阻止裂纹向上扩展的效果。同时,裂纹在层状岩体中的扩展是不连续的,裂尖沿层理面发生了水平迁移,整体呈现阶梯状。（3）在三点弯曲条件下,随着单层厚度的减小,岩体破裂时的裂纹总长度先增大后减小。（4）裂纹在岩体层面扩展时破裂类型多为滑移与拉张破裂的组合,而在非层理面的岩体内部扩展时,以拉张破裂为主。（5）薄层状岩体在三点弯曲条件下,声发射事件在岩体的压密阶段几乎没有出现,直至接近峰值载荷时才大量涌现。到了载荷快速下降时,单位时间的声发射事件数也达到最大。研究结果将对预测层状岩石的裂缝演化提供依据。 相似文献
10.
岩石内部细观裂纹的存在,对压缩作用下岩石剪切断裂的宏观现象有着重要的影响。然而,能够通过解析解阐释细观裂纹几何特性、围压等影响因素对压缩作用下剪切断裂面角度变化趋势的研究很少。基于Ashby模型中提出的裂纹尖端应力强度因子,提出了一种改进的考虑裂纹角度影响的应力强度因子表达式。利用该改进的应力强度因子表达式,推出了一个可以预测岩石峰值强度的裂纹扩展、应变与应力之间的本构关系。结合本构关系的峰值强度与摩尔-库仑失效准则,得到了岩石损伤与内摩擦角、黏聚力、剪切强度及失效断裂面角度之间的理论关系;讨论了围压、裂纹尺寸、角度及摩擦系数对岩石宏观剪切断裂面角度的影响,通过试验结果验证了模型合理性。结果表明：随着损伤增大,内摩擦角、黏聚力及剪切强度不断减小;随着围压增大、摩擦系数增大和初始裂纹尺寸减小,剪切断裂面角度不断增大;随着裂纹角度增大,剪切断裂纹面角度先减小后增大。 相似文献
11.
Summary ?Cracks that initiate from pre-existing discontinuities can link with other cracks or with other discontinuities and produce
failure in a rock mass. The Displacement Discontinuity Method (DDM), FROCK, is used in this investigation to model experimental
observations on pre-cracked specimens of gypsum. In these experiments two fractures, which were either both open or closed,
were placed through the thickness of the specimens, and detailed observations of the cracking process were performed as the
specimens were loaded in uniaxial compression. The following aspects are studied for both open and closed fractures: 1) crack
initiation stress; 2) direction and propagation of the new cracks; 3) type of coalescence and stress at which it occurs. Modeling
is done considering the actual size of the specimens. Relations between the direction of initiation for each type of crack,
the orientation of the initial fractures, and the type and coalescence are established. In addition, comparisons between results
from experiments and predictions from the model are presented. The numerical results are in agreement with the experiments. 相似文献
12.
Three-dimensional surface crack initiation and propagation in two kinds of heterogeneous rocks were numerically investigated via parallel finite element analysis using a supercomputer. Numerically simulated rock specimens containing a pre-existing flaw were subjected to uniaxial compression until failure. The initiation and propagation of wing cracks, anti-wing cracks, and shell-like cracks were reproduced by numerical simulations. The numerically simulated results demonstrate that the further propagation of wing cracks and shell-like cracks stop due to their wrapping (curving) behavior in three-dimensional spaces, even if the applied loads continue to increase. Furthermore, rock heterogeneity could significantly influence crack propagation patterns and the peak uniaxial compressive strengths of rock specimens. Moreover, anti-wing cracks only appeared in relatively heterogeneous rocks, and the peak uniaxial compressive strengths of the specimens were observed to depend on the inclination of the pre-existing flaw. Finally, the mechanism of surface crack propagation is discussed in the context of numerically simulated anti-plane loading tests, wherein it was identified that Mode III loading (anti-plane loading) does not lead to Mode III fracture in rocks due to their high ratio of uniaxial compressive strength to tensile strength. This finding could explain the lateral growth of an existing flaw in its own plane, which is a phenomenon that has not been observed in laboratory experiments. 相似文献
13.
X. J. Li W. M. Yang L. G. Wang I. B. Butler 《Rock Mechanics and Rock Engineering》2014,47(6):2211-2223
Splitting failure, which is recognized as a special engineering geology phenomenon, occurs continually in the brittle rock mass of caverns during underground excavation. In this paper, a splitting model of linear slippage crack groups is built with fracture mechanics, energy analysis, and crack extension theories. Considering intrinsic cracks in rock mass and change of outer stress, intrinsic cracks propagate into macroscopical splitting cracks that are approximately parallel to the side wall of caverns. The splitting criterion of cavern rock mass and the method for predicting displacement in view of splitting opening displacement are proposed. In the end, the forecasting method is applied to the Jinping-I Hydropower Station, underground caverns engineering in China, the splitting failure zone and forecasting displacement are accordant with the monitoring data. The new forecasting displacement method is proven to contribute to the construction of similar underground caverns. 相似文献
14.
Life-time prediction for rocks under static compressive and tensile loads: a new simulation approach 总被引：2，自引：0，他引：2
The life time or time to failure of rocks under load is governed by microstructural defects, like microcracks, voids etc.
The life time can be predicted either by empirical exponential laws or physical laws based on damage and fracture mechanics.
The proposed numerical model is based on subcritical crack growth using the linear elastic fracture mechanical approach and
is implemented as a numerical cellular automate. The algorithm considers both tensile and shear fracturing. Each cell contains
a microcrack of random length according to a given probability function. Fracture growth is controlled by the Charles equation.
Macroscopic cracks are the results of the coalescence of growing microcracks. Within the numerical approach elasto-plastic
stress redistributions take place. If the stress intensity factors have reached the critical values or the microcrack has
reached the zone dimension, the zone is considered as fractured and residual strength values are assigned. The proposed approach
was applied to rock samples under uniaxial compressive and tensile loads (creep tests). Successful results were obtained in
respect to the predicted life time, damage evolution and the fracture pattern. Conclusions for further improvements and extensions
of this methodology were drawn. 相似文献
15.
岩体裂纹的水力劈裂是岩体开裂渗漏甚至施工涌水的重要影响因素之一,也是岩土工程界的研究热点。从断裂力学角度分析了爆破开挖对岩体含水裂纹扩展的扰动作用,结果表明,爆破开挖扰动下,岩体含水裂纹的扩展,与爆炸应力波强度及其入射角、地应力的大小与方向、孔隙水压大小、裂纹的倾角及断裂韧度等因素相关;爆炸应力波的作用,相当于增大了岩体裂纹中的孔隙水压力,每1 cm/s的峰值振动速度相当于增大100 kPa的孔隙水压力,爆破振动速度越大,所产生的爆破扰动荷载越大;岩体开挖引起的岩体裂纹近区地应力及其孔隙水压力的变化,对裂纹的失稳与扩展具有较复杂的影响,可改变裂纹的失稳扩展模式。 相似文献
16.
黏土岩作为高放废物地质处置库的备选介质,目前得到世界各国的高度重视。黏土岩地质处置库巷道施工过程中,一方面,围岩因开挖损伤生成裂隙使得渗透性增强,对核素的阻滞作用降低;另一方面,在应力和水的耦合作用下,黏土岩良好的裂隙渗透损伤自修复能力使得围岩的渗透性逐渐恢复接近于原始状态。基于电阻率测试,首先开展了黏土岩试样在不同条件下的饱和过程试验研究,得到了黏土岩试样饱和过程中等效电阻率的变化规律,分析了不同损伤程度试样、盐溶液对等效电阻率的影响,进而揭示黏土岩饱和过程中水分运移规律。试验结果表明：（1）等效电阻率随着含水率增加而逐渐减小,并逐渐趋于一个稳定值;（2）等效电阻率的大小不仅与含水率有关,试样内部裂隙的存在也会影响等效电阻率分布,这一发现为电阻率法可以探测试样中裂隙的存在提供了依据;（3）水流在黏土岩中扩散,内部裂隙成为优先通道,水流在裂隙中的快速扩散加快了黏土岩的饱和速度。同时,随着黏土岩中水分与黏土矿物的水化膨胀反应,内部裂隙有一定程度闭合,加深对裂隙闭合机制认识,通过电阻率测试可以有效地揭示这一过程。 相似文献
17.
干热岩水压致裂过程中低温诱导热应力与注入水压共同影响裂缝的萌生与扩展。首先通过THM耦合分析了低温压裂液注入过程中注入水压与热应力的相互作用及其对裂缝萌生的影响,随后建立描述岩石细观结构的THMD耦合模型对热应力影响下高温岩石水压致裂过程进行初探。结果表明：低温压裂液注入高温岩石产生的热应力包括岩石自身温度梯度形成的热应力与岩石颗粒非均匀膨胀导致的热应力,并在井筒周围呈现为拉应力。高注入压力将抑制热应力导致的多裂缝萌生,井筒附近热应力的存在对注入压力也具有削弱作用。基岩温度升高,裂缝萌生阶段更多裂缝在井筒附近起裂,缝网沿最大地应力方向的扩展速度减慢,但改造规模增加,同时多裂缝的存在也使得裂缝延伸压力增加。 相似文献
18.
影响高演化泥岩盖层封闭性的主控因素分析 总被引：2，自引：0，他引：2
一般认为泥岩盖层的封闭性随着成岩作用的加深而变差,但是大量油气藏发现和实验测试结果证明高演化泥岩仍具有较高的突破压力和较好的油气封闭性.影响高演化泥岩盖层封闭性的主要因素是什么？如何确定高演化泥岩盖层产生破裂的边界条件,一直是影响其有效性评价的重要基础问题,本文通过对野外泥岩中脉体的包裹体测温,结合地层埋藏史恢复,重建... 相似文献
19.
In this paper, a coupled constitutive model is proposed for anisotropic damage and permeability variation in brittle rocks under deviatoric compressive stresses. The formulation of the model is based on experimental evidences and main physical mechanisms involved in the scale of microcracks are taken into account. The proposed model is expressed in the macroscopic framework and can be easily implemented for engineering application. The macroscopic free enthalpy of cracked solid is first determined by approximating crack distribution by a second‐order damage tensor. The effective elastic properties of damaged material are then derived from the free enthalpy function. The damage evolution is related to the crack growth in multiple orientations. A pragmatic approach inspired from fracture mechanics is used for the formulation of the crack propagation criterion. Compressive stress induced crack opening is taken into account and leads to macroscopic volumetric dilatancy and permeability variation. The overall permeability tensor of cracked material is determined using a micro–macro averaging procedure. Darcy's law is used for fluid flow at the macroscopic scale whereas laminar flow is assumed at the microcrack scale. Hydraulic connectivity of cracks increases with crack growth. The proposed model is applied to the Lac du Bonnet granite. Generally, good agreement is observed between numerical simulations and experimental data. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
20.
用盒维数方法估计了受压岩石表面断裂带的分维值,研究了分维值随载荷、结构(平板伏试件合圆孔或与加载方向成不同角度的割缝)、岩性(大理岩、灰岩、砂岩)和粒度的变化特征,分析了统计自相似性成立的范围与岩性和粒度的关系。研究结果表明。在微裂纹发育未连通为宏观断裂带阶段,分维值随载荷上升而上升,当宏观断裂带形成之后,分维值保持为常数,且随岩性不同而不同。对于所测三种岩石,自相似性成立的尺度范围的上限为颗粒尺寸的Zyljlo倍。最后,结合岩石破裂过程的能量耗散机理,讨论了岩石分维断裂的物理意义。 相似文献