共查询到20条相似文献，搜索用时 78 毫秒
1.
Roman Pevzner Valeriya Shulakova Anton Kepic Milovan Urosevic 《Geophysical Prospecting》2011,59(1):66-77
Time‐lapse seismics is the methodology of choice for remotely monitoring changes in oil/gas reservoir depletion, reservoir stimulation or CO2 sequestration, due to good sensitivity and resolving power at depths up to several kilometres. This method is now routinely applied offshore, however, the use of time‐lapse methodology onshore is relatively rare. The main reason for this is the relatively high cost of commercial seismic acquisition on land. A widespread belief of a relatively poor repeatability of land seismic data prevents rapid growth in the number of land time‐lapse surveys. Considering that CO2 sequestration on land is becoming a necessity, there is a great need to evaluate the feasibility of time‐lapse seismics for monitoring. Therefore, an understanding of the factors influencing repeatability of land seismics and evaluating limitations of the method is crucially important for its application in many CO2 sequestration projects. We analyse several repeated 2D and 3D surveys acquired within the Otway CO2 sequestration pilot project (operated by the Cooperative Research Centre for Greenhouse Technologies, CO2CRC) in Australia, in order to determine the principal limitations of land time‐lapse seismic repeatability and investigate the influence of the main factors affecting it. Our findings are that the intrinsic signal‐to‐noise ratio (S/N, signal to coherent and background noise levels) and the normalized‐root‐mean‐square (NRMS) difference are controlled by the source strength and source type. However, the post‐stack S/N ratio and corresponding NRMS residuals are controlled mainly by the data fold. For very high‐fold data, the source strength and source type are less critical. 相似文献
2.
Two formulae are developed for estimating horizontal permeability directly from maps of 4D seismic signatures. The choice of the formula used depends on whether the seismic is dominated by changes of pressure or saturation. However, pressure derived from time‐lapse seismic, or seismic amplitudes controlled predominantly by pressure are to be preferred for optimal ‘illumination’ of the reservoir. The permeability is predicted to be dependent on porosity but weighted by a 4D term related to the magnitude and spatial gradient of the 4D signature. Tests performed on model‐based synthetic seismic data affirm the validity and accuracy of this approach. Application to field data from the UK continental shelf reveals a large‐scale permeability variation similar to the existing simulation model, but with additional fine‐scale detail. The technique thus has the potential of providing extra information with which to update the simulation model. The resultant permeability estimates have been successfully ground‐truthed against the results of two well tests. As non‐repeatable noise in the time‐lapse seismic data diminishes with improved 4D‐related acquisition, it will become increasingly possible to make robust permeability estimates using this approach. 相似文献
3.
Analysis of time‐lapse travel‐time and amplitude changes to assess reservoir compartmentalization 
下载免费PDF全文
下载免费PDF全文 Fluid depletion within a compacting reservoir can lead to significant stress and strain changes and potentially severe geomechanical issues, both inside and outside the reservoir. We extend previous research of time‐lapse seismic interpretation by incorporating synthetic near‐offset and full‐offset common‐midpoint reflection data using anisotropic ray tracing to investigate uncertainties in time‐lapse seismic observations. The time‐lapse seismic simulations use dynamic elasticity models built from hydro‐geomechanical simulation output and a stress‐dependent rock physics model. The reservoir model is a conceptual two‐fault graben reservoir, where we allow the fault fluid‐flow transmissibility to vary from high to low to simulate non‐compartmentalized and compartmentalized reservoirs, respectively. The results indicate time‐lapse seismic amplitude changes and travel‐time shifts can be used to qualitatively identify reservoir compartmentalization. Due to the high repeatability and good quality of the time‐lapse synthetic dataset, the estimated travel‐time shifts and amplitude changes for near‐offset data match the true model subsurface changes with minimal errors. A 1D velocity–strain relation was used to estimate the vertical velocity change for the reservoir bottom interface by applying zero‐offset time shifts from both the near‐offset and full‐offset measurements. For near‐offset data, the estimated P‐wave velocity changes were within 10% of the true value. However, for full‐offset data, time‐lapse attributes are quantitatively reliable using standard time‐lapse seismic methods when an updated velocity model is used rather than the baseline model. 相似文献
4.
Shiv N. Dasgupta 《Geophysical Prospecting》2005,53(2):215-227
Ghawar, the largest oilfield in the world, produces oil from the Upper Jurassic Arab‐D carbonate reservoir. The high rigidity of the limestone–dolomite reservoir rock matrix and the small contrast between the elastic properties of the pore fluids, i.e. oil and water, are responsible for the weak 4D seismic effect due to oil production. A feasibility study was recently completed to quantify the 4D seismic response of reservoir saturation changes as brine replaced oil. The study consisted of analysing reservoir rock physics, petro‐acoustic data and seismic modelling. A seismic model of flow simulation using fluid substitution concluded that time‐lapse surface seismic or conventional 4D seismic is unlikely to detect the floodfront within the repeatability of surface seismic measurements. Thus, an alternative approach to 4D seismic for reservoir fluid monitoring is proposed. Permanent seismic sensors could be installed in a borehole and on the surface for passive monitoring of microseismic activity from reservoir pore‐pressure perturbations. Reservoir production and injection operations create these pressure or stress perturbations. Reservoir heterogeneities affecting the fluid flow could be mapped by recording the distribution of epicentre locations of these microseisms or small earthquakes. The permanent borehole sensors could also record repeated offset vertical seismic profiling surveys using a surface source at a fixed location to ensure repeatability. The repeated vertical seismic profiling could image the change in reservoir properties with production. 相似文献
5.
The ultimate goal of reservoir simulation in reservoir surveillance technology is to estimate long-term production forecasting and to plan development and management of petroleum fields. However, maintaining reliable reservoir models which honour available static and dynamic data, involve inherent risks due to the uncertainties in space and time of the distribution of hydrocarbons inside reservoirs. Recent applications have shown that these uncertainties can be reduced by quantitative integration of seismic data into the reservoir modelling workflows to identify which areas and reservoir attributes of the model should be updated. This work aims using seismic data to reduce ambiguity in calibrating reservoir flow simulation model with an uncertain petro-elastic model, proposing a circular workflow of inverted seismic impedance (3D and 4D) and engineering studies, with emphasis on the interface between static and dynamic models. The main contribution is to develop an updating procedure for adjusting reservoir simulation response before using it in the production forecasting and enhance the interpretive capability of reservoir properties. Accordingly, the workflow evaluates consistency of reservoir simulation model and inverted seismic impedance, assisted by production history data, to close the loop between reservoir engineering and seismic domains. The methodology is evaluated in a complex, faulted, sandstone reservoir, the Norne benchmark field, where a significant reservoir behaviour understanding (about the static and dynamic reservoir properties) is obtained towards the quantitative integration of seismic impedance data. This leads to diagnosis of the reservoir flow simulation reliability and generation of an updated simulation model consistent with observed seismic and well production history data, as well as a calibrated petro-elastic model. Furthermore, as Norne Field is a benchmark case, this study can be considered to enrich the discussions over deterministic or probabilistic history matching studies. 相似文献
6.
Jean‐Paul van Gestel Kevin D. Best Olav I. Barkved Jan H. Kommedal 《Geophysical Prospecting》2011,59(4):673-681
The frequent time‐lapse observations from the life of field seismic system across the Valhall field provide a wealth of information. The responses from the production and injection wells can be observed through time‐shift and amplitude changes. These observations can be compared to modelled synthetic seismic responses from a reservoir simulation model of the Valhall Field. The observed differences between the observations and the modelling are used to update and improve the history match of the reservoir model. The uncertainty of the resulting model is reduced and a more confident prediction of future reservoir performance is provided. A workflow is presented to convert the reservoir model to a synthetic seismic response and compare the results to the observed time‐lapse responses for any time range and area of interest. Correlation based match quality factors are calculated to quantify the visual differences. This match quality factor allows us to quantitatively compare alternative reservoir models to help identify the parameters that best match the seismic observations. Three different case studies are shown where this workflow has helped to reduce the uncertainty range associated with specific reservoir parameters. By updating various reservoir model parameters we have been able to improve the match to the observations and thereby improve the overall reservoir model predictability. The examples show positive results in a range of different reservoir modelling issues, which indicates the flexibility of this workflow and the ability to have an impact in most reservoir modelling challenges. 相似文献
7.
An approach is developed to estimate pore‐pressure changes in a compacting chalk reservoir directly from time‐lapse seismic attributes. It is applied to data from the south‐east flank of the Valhall field. The time‐lapse seismic signal of the reservoir in this area is complex, despite the fact that saturation changes do not have an influence. This complexity reflects a combination of pressure depletion, compaction and stress re‐distribution throughout the reservoir and into the surrounding rocks. A simple relation is found to link the time‐lapse amplitude and time‐shift attributes to variations in the key controlling parameter of initial porosity. This relation is sufficient for an accurate estimation of pore‐pressure change in the inter‐well space. Although the time‐lapse seismic estimates mostly agree with reservoir simulation, unexplained mismatches are apparent at a small number of locations with lower porosities (less than 38%). The areas of difference between the observations and predictions suggest possibilities for simulation model updating or a better understanding of the physics of the reservoir. 相似文献
8.
We present an approach that creates the possibility of reservoir monitoring on a quasi‐continuous basis using surface seismic data. Current strategies and logistics for seismic data acquisition impose restrictions on the calendar‐time temporal resolution obtainable for a given surface‐seismic time‐lapse monitoring program. One factor that restricts the implementation of a quasi‐continuous monitoring program using conventional strategies is the time it takes to acquire a complete survey. Here quasi‐continuous monitoring describes the process of reservoir monitoring at short‐time intervals. Our approach circumvents the restriction by requiring only a subset of complete survey data each time an image of the reservoir is needed using surface seismic data. Ideally, the time interval between survey subset acquisitions should be short so that changes in the reservoir properties are small. The accumulated data acquired are used to estimate the unavailable data at the monitor survey time and the combined recorded and estimated data are used to produce an image of the subsurface for monitoring. We will illustrate the effectiveness of our approach using 2D and 3D synthetic seismic data and 3D field seismic data. We will explain the benefits and drawbacks of the proposed approach. 相似文献
9.
Time‐lapse seismic surveying has become an accepted tool for reservoir monitoring applications, thus placing a high premium on data repeatability. One factor affecting data repeatability is the influence of the rough sea‐surface on the ghost reflection and the resulting seismic wavelets of the sources and receivers. During data analysis, the sea‐surface is normally assumed to be stationary and, indeed, to be flat. The non‐flatness of the sea‐surface introduces amplitude and phase perturbations to the source and receiver responses and these can affect the time‐lapse image. We simulated the influence of rough sea‐surfaces on seismic data acquisition. For a typical seismic line with a 48‐fold stack, a 2‐m significant‐wave‐height sea introduces RMS errors of about 5–10% into the stacked data. This level of error is probably not important for structural imaging but could be significant for time‐lapse surveying when the expected difference anomaly is small. The errors are distributed differently for sources and receivers because of the different ways they are towed. Furthermore, the source wavelet is determined by the sea shape at the moment the shot is fired, whereas the receiver wavelet is time‐varying because the sea moves significantly during the seismic record. 相似文献
10.
Stephen A. Hall † Colin MacBeth Jan Stammeijer Mark Omerod 《Geophysical Prospecting》2006,54(1):63-73
In the Southern Gas Basin (SGB) of the North Sea there are many mature gas fields where time‐lapse monitoring could be very beneficial in extending production life. However, the conditions are not immediately attractive for time‐lapse seismic assessment. This is primarily because the main production effect to be assessed is a pore pressure reduction and frame stiffening because of gas production in tight sandstone reservoirs that also have no real seismic direct hydrocarbon indicators. Modelling, based on laboratory measurements, has shown that such an effect would be small and difficult to detect in seismic data. This paper makes two main contributions. Firstly, this is, to our knowledge, the first time‐lapse study in the SGB and involves a real‐data assessment of the viability for detecting production in such an environment. Secondly, the feasibility of using markedly different legacies of data in such a study is addressed, including an assessment of the factors influencing the crossmatching. From the latter, it is found that significant, spatially varying time shifts need to be, and are successfully, resolved through 3‐D warping. After the warping, the primary factors limiting the crossmatching appear to be residual local phase variations, possibly induced by the differing migration strategies, structure, reverberations and different coherencies of the volumes, caused by differences in acquisition‐structure azimuth and acquisition fold. Despite these differences, a time‐lapse amplitude signature is observed that is attributable to production. The character of the 4‐D amplitude anomalies may also indicate variations in stress sensitivity, e.g. because of zones of fracturing. Additionally, warping‐derived time attributes have been highlighted as a potential additional avenue for detection of pressure depletion in such reservoirs. Although the effects are subtle, they may indicate changes in stress/pressure in and around the reservoir because of production. However, to fully resolve the subtle time‐lapse effects in such a reservoir, the data differences need to be better addressed, which may be possible by full re‐processing and pre‐stack analysis, but more likely dedicated 4‐D acquisition would be required. 相似文献
11.
The possibility of using 4D seismic data for monitoring pressure depletion in the low‐porosity, tight gas‐bearing Rotliegende sandstones of the UK Southern Gas Basin is investigated. The focus here is on whether fractures in the upper part of the reservoir, known to enhance productivity, can also enhance the time‐lapse seismic response. The study uses laboratory data to evaluate core‐plug stress sensitivity, published data for the stress behaviour of the fractures, followed by petro‐elastic and 4D seismic modelling of both the fractured and unfractured formation. The magnitude of the resultant 4D signatures suggests that production‐induced changes in the unfractured sands are unlikely to be observed except perhaps with highly repeatable time‐lapse surveys. On the other hand, the presence of fractures could render production effects visible in dedicated 4D acquisition or prestack parallel processed data. If present however, the signature will be sporadic, as fractures in the area are known to exist in clusters. The 4D signature may be enhanced further by certain classes of vertical geological variability and also areas of high reservoir pressure. The strongest evidence of depletion is expected to be time‐shifts seen at the base of the Rotliegende reservoir. 相似文献
12.
With the increasing use of permanently installed seismic installations, many of the issues in time‐lapse seismic caused by the lack of repeatability can be reduced. However, a number of parameters still influence the degree of reliability of 4D seismic data. In this paper, the specific impact of seawater velocity variations on time‐lapse repeatability is investigated in a synthetic study. A zero‐lag time‐lapse seabed experiment with no change in the subsurface but with velocity changes in the water column is simulated. The velocity model in the water column is constant for the baseline survey while the model for the repeat survey is heterogeneous, designed from sea salinity and temperature measurements in the West of Shetlands. The difference section shows up to 80% of residual amplitude, which highlights the poor repeatability. A new dynamic correction which removes the effect of seawater velocity variations specifically for permanent installations is developed. When applied to the synthetic data, it reduces the difference residual amplitude to about 3%. This technique shows substantial improvement in repeatability beyond conventional time‐lapse cross‐equalization. 相似文献
13.
Combined time‐lapse reservoir simulation and seismic modelling has been performed on both 1D and 3D models of a channelized turbidite reservoir. The models have been built using core, log, laboratory and seismic data from the Nelson Field (central North Sea) as a template. Oil and water movement in the main channels, channel margins and interchannel regions is investigated, with a particular focus being the effect of poor net‐to‐gross. The analysis confirms that saturation effects dominate the response whilst stress‐sensitivity effects play a minor role. The trough–peak signature in the seismic difference volumes formed by the sweep of the water can be continued and mapped slightly further than the channel margins. This characteristic 4D signature remains roughly intact, despite the complicated depositional architecture, and accurately delineates the area of moved fluid, but it needs additional calibration to combat the detrimental influence of the low net‐to‐gross. Signal strength is largely dependent on reservoir quality, but is also compromised by the net‐to‐gross, fluid distribution and, more critically, by the exact timing of the seismic survey. For example, a region of bypassed oil zone remains undetected as it forms early during the production. This work demonstrates that to understand fully the 4D signature at a quantitative level requires adequate knowledge of the fluid properties, but also, more critically, the geology. 相似文献
14.
Overburden complexity and repeatability of seismic data: Impacts of positioning errors at the Oseberg field, North Sea 总被引：2，自引：0，他引：2
Repeatability of seismic data plays a crucial role in time‐lapse seismic analysis. There are several factors that can decrease the repeatability, such as positioning errors, varying tide, source variations, velocity changes in the water layer (marine data) and undesired effects of various processing steps. In this work, the complexity of overburden structure, as an inherent parameter that can affect the repeatability, is studied. A multi‐azimuth three‐dimensional vertical‐seismic‐profiling data set with 10 000 shots is used to study the relationship between overburden structure and repeatability of seismic data. In most repeatability studies, two data sets are compared, but here a single data set has been used because a significant proportion of the 10 000 shots are so close to each other that a repeatability versus positioning error is possible. We find that the repeatability decreases by a factor of approximately 2 under an overburden lens. Furthermore, we find that the X‐ and Y‐components have approximately the same sensitivity to positioning errors as the Z‐component (for the same events) in this three‐dimensional vertical‐seismic‐profiling experiment. This indicates that in an area with complex overburden, positioning errors between monitor and base seismic surveys are significantly more critical than outside such an area. This study is based on a three‐dimensional three‐component vertical‐seismic‐profiling data set from a North Sea reservoir and care should be taken when extrapolating these observations into a general four‐dimensional framework. 相似文献
15.
Seismic wave propagation through a fluid-saturated poroelastic layer might be strongly affected by media heterogeneities. Via incorporating controlled laboratory simulation experiments, we extend previous studies of time-lapse seismic effects to evaluate the wave scattering influence of the heterogeneous nature of porous permeable media and the associated amplification effects on 4D seismic response characteristics of reservoir fluid substitution. A physical model consisted of stratified thin layers of shale and porous sandstone reservoir with rock heterogeneities was built based on the geological data of a real hydrocarbon-saturated reservoir in Northeast China. Multi-surveys data of good quality were acquired by filling poroelastic reservoir layers with gas, water and oil in sequence. Experimental observations show that reservoir heterogeneity effect causes significantly magnified abnormal responses to the fluid-saturated media. Specifically, reflection signatures of the gas-filled reservoir are dramatically deviated from those of the liquid fluid-filled reservoir, compared with ones of the homogeneous media. By removing the influences unrelated to reservoir property alterations, 4D seismic estimates of travel-time and frequency-dependent characteristic are reasonably consistent with fluid variations. Nevertheless, strong 4D amplitude difference anomalies might not correspond to the regions where fluid variations occur. We also find that 4D seismic difference attributes are evident between oil- and water-filled models, whereas significant between oil- and gas-filled models. Meanwhile, rock physics modelling results reveal the predicted 4D seismic differences are obviously smaller than those calculated from seismic observations. The results in this paper, therefore, implicate that the effect of a reservoir's heterogeneous nature might be beneficial for hydrocarbons detection as well as monitoring small variations in pore fluids. 相似文献
16.
观测系统的重复性是时移地震的关键问题.而对于全面评价,多道重复性度量又是很有意义的.基于归一化均方根差异计算方法,地震多道数据的重复性一般为单道数据重复性的加权均方根.针对海上拖缆监测数据与基线数据多道匹配不确定的问题,采取了定向最佳匹配原则和失配虚拟技术方法.基于地震数据重复性与观测系统重复性的线性相关模型,研究了时移地震观测系统的多道加权均方根重复性特征.结合实际数据研究表明,基于面元的观测系统最佳定向匹配的多道加权均方根重复性基本反映全部观测系统的重复性和覆盖程度. 相似文献
17.
P‐wave data from a time‐lapse 3D OBC survey have been analysed to estimate and interpret azimuthal seismic anisotropy. This is achieved by careful processing to preserve the azimuthal signature. The survey images a major reservoir body in a channelized turbidite field in the Gulf of Mexico. Three distinct and significant anisotropy anomalies are discovered on or around this particular ‘4500‐ft sand’, all of which change intensity but not orientation with hydrocarbon production. These anomalies are distributed along the highest concentration of cumulative sand thickness, with their symmetry axes aligned with the main channel axis. We suspect that this time‐lapse anisotropy could be caused by the alignment of the depositional grain fabric. Theoretical calculation predicts that this mechanism, when combined with fluid‐saturation changes, can generate the observed pattern of behaviour. If further supported by other researchers, this result would indicate that appropriately designed seismic surveys could be a useful tool for palaeo‐direction studies in clastic reservoirs and also a useful constraint for directional permeability in the reservoir flow simulation model. 相似文献
18.
During the time taken for seismic data to be acquired, reservoir pressure may fluctuate as a consequence of field production and operational procedures and fluid fronts may move significantly. These variations prevent accurate quantitative measurement of the reservoir change using 4D seismic data. Modelling studies on the Norne field simulation model using acquisition data from ocean-bottom seismometer and towed streamer systems indicate that the pre-stack intra-survey reservoir fluctuations are important and cannot be neglected. Similarly, the time-lapse seismic image in the post-stack domain does not represent a difference between two states of the reservoir at a unique base and monitor time, but is a mixed version of reality that depends on the sequence and timing of seismic shooting. The outcome is a lack of accuracy in the measurement of reservoir changes using the resulting processed and stacked 4D seismic data. Even for perfect spatial repeatability between surveys, a spatially variant noise floor is still anticipated to remain. For our particular North Sea acquisition data, we find that towed streamer data are more affected than the ocean-bottom seismometer data. We think that this may be typical for towed streamers due to their restricted aperture compared to ocean-bottom seismometer acquisitions, even for a favourable time sequence of shooting and spatial repeatability. Importantly, the pressure signals on the near and far offset stacks commonly used in quantitative 4D seismic inversion are found to be inconsistent due to the acquisition timestamp. Saturation changes at the boundaries of fluid fronts appear to show a similar inconsistency across sub-stacks. We recommend that 4D data are shot in a consistent manner to optimize aerial time coverage, and that additionally, the timestamp of the acquisition should be used to optimize pre-stack quantitative reservoir analysis. 相似文献
19.
The cross‐calibration of different vintage data is an important prerequisite in attempting to determine the time‐lapse seismic effects induced by hydrocarbon production in a reservoir. This paper reports the preprocessing and cross‐calibration procedures adopted to modify the data of four seismic vintages (1982, 1989, 1992 and 1999) from the Oseberg field in the North Sea, for optimal conditions for a time‐lapse seismic amplitude analysis. The final results, in terms of time‐lapse variations, of acoustic impedance and of amplitude‐versus‐offset, are illustrated for selected data sets. The application of preprocessing to each individual vintage data set reduces the effects of the different acquisition and noise conditions, and leads to consistency in the amplitude response of the four vintages. This consistency facilitates the final amplitude cross‐calibration that is carried out using, as reference, the Cretaceous horizon reflections above the Brent reservoir. Such cross‐calibration can be considered as vintage‐consistent residual amplitude correction. Acoustic impedance sections, intercept and gradient amplitude‐versus‐offset attributes and coherent amplitude‐versus‐offset estimates are computed on the final cross‐calibrated data. The results, shown for three spatially coincident 2D lines selected from the 1982, 1989 and 1999 data sets, clearly indicate gas‐cap expansion resulting from oil production. Such expansion is manifested as a decrease in acoustic impedance and a modification of the amplitude‐versus‐offset trends in the apical part of the reservoir. 相似文献
20.
Bayesian inversion of time‐lapse seismic data for the estimation of static reservoir properties and dynamic property changes 下载免费PDF全文
下载免费PDF全文 Seismic conditioning of static reservoir model properties such as porosity and lithology has traditionally been faced as a solution of an inverse problem. Dynamic reservoir model properties have been constrained by time‐lapse seismic data. Here, we propose a methodology to jointly estimate rock properties (such as porosity) and dynamic property changes (such as pressure and saturation changes) from time‐lapse seismic data. The methodology is based on a full Bayesian approach to seismic inversion and can be divided into two steps. First we estimate the conditional probability of elastic properties and their relative changes; then we estimate the posterior probability of rock properties and dynamic property changes. We apply the proposed methodology to a synthetic reservoir study where we have created a synthetic seismic survey for a real dynamic reservoir model including pre‐production and production scenarios. The final result is a set of point‐wise probability distributions that allow us to predict the most probable reservoir models at each time step and to evaluate the associated uncertainty. Finally we also show an application to real field data from the Norwegian Sea, where we estimate changes in gas saturation and pressure from time‐lapse seismic amplitude differences. The inverted results show the hydrocarbon displacement at the times of two repeated seismic surveys. 相似文献