首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
DEMs as important input parameters of environmental risk assessment models are notable sources of uncertainties. To illustrate the effect of DEM grid size and source on model outputs, a widely used watershed management model, the Soil and Water Assessment Tool (SWAT), was applied with two newly available DEMs as inputs (i.e. ASTER GDEM Version 1, and SRTM Version 4.1). A DEM derived from 1:10,000 high resolution digital line graph (DLG) was used as a baseline for comparisons. Eleven resample resolutions, from 5 to 140?m, were considered to evaluate the impact of DEM resolution on SWAT outputs. Results from a case study in South-eastern China indicate that the SWAT predictions of total phosphorus and total nitrogen decreased substantially with coarser resample resolution. A slightly decreasing trend was found in the SWAT predicted sediment when DEMs were resampled to coarser resolutions. The SWAT predicted runoff was not sensitive to resample resolution. For different data sources, ASTER GDEM did not perform better than SRTM in SWAT simulations even it was provided with a smaller grid size and higher vertical accuracy. The predicted outputs based on ASTER GDEM and SRTM were similar, and much lower than the ones based on DLG. This study presents potential uncertainties introduced by DEM resolutions and data sources, and recommends strategies choosing DEMs based on research objects and maximum acceptable errors.  相似文献   

2.
Mt. Cameroon is one of the most active effusive volcanoes in Africa. About 500,000 people living or working around its fertile flanks are subject to significant threat from lava flow inundation. Lava flow hazard and risk were assessed by simulating probable lava flow paths using the DOWNFLOW code. The vent opening probability density function and lava flow length distribution were determined on the basis of available data from past eruptions at Mt. Cameroon volcano. Code calibration was performed through comparison with real lava flow paths. The topographic basis for simulations was the 90-m resolution SRTM DEM. Simulated lava flows from about 80,000 possible vents were used to produce a detailed lava flow hazard map. The lava flow risk in the area was mapped by combining the hazard map with digitized infrastructures (i.e., human settlements and roads). Results show that the risk of lava flow inundation is greatest in the most inhabited coastal areas comprising the town of Limbe, which constitutes the center of Cameroon’s oil industry and an important commercial port. Buea, the second most important town in the area, has a much lower risk although it is significantly closer to the summit of the volcano. Non-negligible risk characterizes many villages and most roads in the area surrounding the volcano. In addition to the conventional risk mapping described above, we also present (1) two reversed risk maps (one for buildings and one for roads), where each point on the volcano is classified according to the total damage expected as a consequence of vent opening at that point; (2) maps of the lava catchments for the two main towns of Limbe and Buea, illustrating the expected damage upon venting at any point in the catchment basin. The hazard and risk maps provided here represent valuable tools for both medium/long-term land-use planning and real-time volcanic risk management and decision making.  相似文献   

3.
Flood hazard maps used to inform and build resilience in remote communities in the Terai region of southern Nepal are based on outdated and static digital elevation models (DEMs), which do not reflect dynamic river configuration or hydrology. Episodic changes in river course, sediment dynamics, and the distribution of flow down large bifurcation nodes can modify the extent of flooding in this region, but these processes are rarely considered in flood hazard assessment. Here, we develop a 2D hydrodynamic flood model of the Karnali River in the Terai region of west Nepal. A number of scenarios are tested examining different DEMs, variable bed elevations to simulate bed aggradation and incision, and updating bed elevations at a large bifurcation node to reflect field observations. By changing the age of the DEM used in the model, a 9.5% increase in inundation extent was observed for a 20-year flood discharge. Reducing horizontal DEM resolution alone resulted in a <1% change. Uniformly varying the bed elevation led to a 36% change in inundation extent. Finally, changes in bed elevation at the main bifurcation to reflect observed conditions resulted in the diversion of the majority of flow into the west branch, consistent with measured discharge ratios between the two branches, and a 32% change in inundation extent. Although the total flood inundation area was reduced (−4%), there was increased inundation along the west bank. Our results suggest that regular field measurements of bed elevation and updated DEMs following large sediment-generating events, and at topographically sensitive areas such as large river bifurcations, could help improve model inputs in future flood prediction models. This is particularly important following flood events carrying large sediment loads out of mountainous regions that could promote bed aggradation and channel switching across densely populated alluvial river systems and floodplains further downstream. © 2020 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd  相似文献   

4.
The resolution and accuracy of digital elevation models (DEMs) can affect the hydraulic simulation results for predicting the effects of glacial lake outburst floods (GLOFs). However, for the Tibetan Plateau, high‐quality DEM data are often not available, leaving researchers with near‐global, freely available DEMs, such as the Advanced Spaceborne Thermal Emission and Reflection Radiometer Global Digital Elevation Model (ASTER GDEM) and the Shuttle Radar Topography Mission data (SRTM) for hydraulic modelling. This study explores the suitability of these two freely available DEMs for hydraulic modelling of GLOFs. Our study focused on the flood plain of a potentially dangerous glacial lake in southeastern Tibet, to evaluate the elevation accuracy of ASTER GDEM and SRTM, and their suitability for hydraulic modelling of GLOFs. The elevation accuracies of ASTER GDEM and SRTM were first validated against field global position system (GPS) survey points, and then evaluated with reference to the relatively high precision of 1:50 000 scale DEM (DEM5) constructed from aerial photography. Moreover, the DEM5, ASTER GDEM and SRTM were used as basic topographic data to simulate peak discharge propagation, as well as flood inundation extent and depth in the Hydrologic Engineering Center's River Analysis System one‐dimensional hydraulic model. Results of the three DEM predictions were compared to evaluate the suitability of ASTER GDEM and SRTM for GLOF hydraulic modelling. Comparisons of ASTER GDEM and SRTM each with DEM5 in the flood plain area show root‐mean‐square errors between the former two as ± 15·4 m and between the latter two as ± 13·5 m. Although SRTM overestimates and ASTER GDEM underestimates valley floor elevations, both DEMs can be used to extract the elevations of required geometric data, i.e. stream centre lines, bank lines and cross sections, for flood modelling. However, small errors still exist in the cross sections that may influence the propagation of peak discharge. The flood inundation extent and mean water depths derived from ASTER GDEM predictions are only 2·2% larger and 2·3‐m deeper than that of the DEM5 predictions, whereas the SRTM yields a flood zone extent 6·8% larger than the DEM5 prediction and a mean water depth 2·4‐m shallower than the DEM5 prediction. The modelling shows that, in the absence of high‐precision DEM data, ASTER GDEM or SRTM DEM can be relied on for simulating extreme GLOFs in southeast Tibet. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

5.
Assessments of pyroclastic flow (PF) hazards are commonly based on mapping of PF and surge deposits and estimations of inundation limits, and/or computer models of varying degrees of sophistication. In volcanic crises a PF hazard map may be sorely needed, but limited time, exposures, or safety aspects may preclude fieldwork, and insufficient time or baseline data may be available for reliable dynamic simulations. We have developed a statistically constrained simulation model for block-and-ash type PFs to estimate potential areas of inundation by adapting methodology from Iverson et al. (Geol Soc America Bull 110:972–984, 1998) for lahars. The predictive equations for block-and-ash PFs are calibrated with data from several volcanoes and given by A = (0.05 to 0.1)V 2/3, B = (35 to 40)V 2/3, where A is cross-sectional area of inundation, B is planimetric area and V is deposit volume. The proportionality coefficients were obtained from regression analyses and comparison of simulations to mapped deposits. The method embeds the predictive equations in a GIS program coupled with DEM topography, using the LAHARZ program of Schilling (1998). Although the method is objective and reproducible, any PF hazard zone so computed should be considered as an approximate guide only, due to uncertainties on the coefficients applicable to individual PFs, the authenticity of DEM details, and the volume of future collapses. The statistical uncertainty of the predictive equations, which imply a factor of two or more in predicting A or B for a specified V, is superposed on the uncertainty of forecasting V for the next PF to descend a particular valley. Multiple inundation zones, produced by simulations using a selected range of volumes, partly accommodate these uncertainties. The resulting maps show graphically that PF inundation potentials are highest nearest volcano sources and along valley thalwegs, and diminish with distance from source and lateral distance from thalweg. The model does not explicitly consider dynamic behavior, which can be important. Ash-cloud surge impact limits must be extended beyond PF hazard zones and we provide several approaches to do this. The method has been used to supply PF and surge hazard maps in two crises: Merapi 2006; and Montserrat 2006–2007.  相似文献   

6.
ABSTRACT

Flood risk management strongly relies on inundation models for river basin zoning in flood-prone and risk-free areas. Floodplain zoning is significantly affected by the diverse and concurrent uncertainties that characterize the modelling chain used for producing inundation maps. In order to quantify the relative impact of the uncertainties linked to a lumped hydrological (rainfall–runoff) model and a FLO-2D hydraulic model, a Monte Carlo procedure is proposed in this work. The hydrological uncertainty is associated with the design rainfall estimation method, while the hydraulic model uncertainty is associated with roughness parameterization. This uncertainty analysis is tested on the case study of the Marta coastal catchment in Italy, by comparing the different frequency, extent and depth of inundation simulations associated with varying rainfall forcing and/or hydraulic model roughness realizations. The results suggest a significant predominance of the hydrological uncertainty with respect to the hydraulic one on the overall uncertainty associated with the simulated inundation maps.  相似文献   

7.
Flood risk assessment is customarily performed using a design flood. Observed past flows are used to derive a flood frequency curve which forms the basis for a construction of a design flood. The simulation of a distributed model with the 1‐in‐T year design flood as an input gives information on the possible inundation areas, which are used to derive flood risk maps. The procedure is usually performed in a deterministic fashion, and its extension to take into account the design flood‐and flow routing model uncertainties is computer time consuming. In this study we propose a different approach to flood risk assessment which consists of the direct simulation of a distributed flow routing model for an observed series of annual maximum flows and the derivation of maps of probability of inundation of the desired return period directly from the obtained simulations of water levels at the model cross sections through an application of the Flood Level Frequency Analysis. The hydraulic model and water level quantile uncertainties are jointly taken into account in the flood risk uncertainty evaluation using the Generalized Likelihood Uncertainty Estimation (GLUE) approach. An additional advantage of the proposed approach lies in smaller uncertainty of inundation predictions for long return periods compared to the standard approach. The approach is illustrated using a design flood level and a steady‐state solution of a hydraulic model to derive maps of inundation probabilities. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

8.
Evaluation of on-line DEMs for flood inundation modeling   总被引：1，自引：0，他引：1  
Recent and highly accurate topographic data should be used for flood inundation modeling, but this is not always feasible given time and budget constraints so the utility of several on-line digital elevation models (DEMs) is examined with a set of steady and unsteady test problems. DEMs are used to parameterize a 2D hydrodynamic flood simulation algorithm and predictions are compared with published flood maps and observed flood conditions. DEMs based on airborne light detection and ranging (LiDAR) are preferred because of horizontal resolution, vertical accuracy (∼0.1 m) and the ability to separate bare-earth from built structures and vegetation. DEMs based on airborne interferometric synthetic aperture radar (IfSAR) have good horizontal resolution but gridded elevations reflect built structures and vegetation and therefore further processing may be required to permit flood modeling. IfSAR and shuttle radar topography mission (SRTM) DEMs suffer from radar speckle, or noise, so flood plains may appear with non-physical relief and predicted flood zones may include non-physical pools. DEMs based on national elevation data (NED) are remarkably smooth in comparison to IfSAR and SRTM but using NED, flood predictions overestimate flood extent in comparison to all other DEMs including LiDAR, the most accurate. This study highlights utility in SRTM as a global source of terrain data for flood modeling.  相似文献   

9.
This study is focused on the integration of bare earth lidar (Light Detection and Ranging) data into unstructured (triangular) finite element meshes and the implications on simulating storm surge inundation using a shallow water equations model. A methodology is developed to compute root mean square error (RMSE) and the 95th percentile of vertical elevation errors using four different interpolation methods (linear, inverse distance weighted, natural neighbor, and cell averaging) to resample bare earth lidar and lidar-derived digital elevation models (DEMs) onto unstructured meshes at different resolutions. The results are consolidated into a table of optimal interpolation methods that minimize the vertical elevation error of an unstructured mesh for a given mesh node density. The cell area averaging method performed most accurate when DEM grid cells within 0.25 times the ratio of local element size and DEM cell size were averaged. The methodology is applied to simulate inundation extent and maximum water levels in southern Mississippi due to Hurricane Katrina, which illustrates that local changes in topography such as adjusting element size and interpolation method drastically alter simulated storm surge locally and non-locally. The methods and results presented have utility and implications to any modeling application that uses bare earth lidar.  相似文献   

10.
The horizontal accuracy of topographic data represented by digital elevation model (DEM) resolution brings about uncertainties in landscape process modeling with raster GIS. This paper presents a study on the effect of topographic variability on cell-based empirical estimation of soil loss and sediment transport. An original DEM of 10m resolution for a case watershed was re-sampled to three realizations of higher grid sizes for a comparative examination. Equations based on the USLE are applied to the watershed to calculate soil loss from each cell and total sediment transport to streams. The study found that the calculated total soil loss from the watershed decreases with the increasing DEM resolution with a linear correlation as spatial variability is reduced by cell aggregation. The USLE topographic factors (LS) extracted from applied DEMs represent spatial variability, and determine the estimations as shown in the modeling results. The commonly used USGS 30m DEM appears to be able to reflect essential spatial variability and suitable for the empirical estimation. The appropriateness of a DEM resolution is dependent upon specific landscape characteristics, applied model and its parameterization. This work attempts to provide a general framework for the research in the DEM-based empirical modeling.  相似文献   

11.
To quantify landscape change resulting from processes of erosion and deposition and to establish spatially distributed sediment budgets, ‘models of change’ can be established from a time series of digital elevation models (DEMs). However, resolution effects and measurement errors in DEMs may propagate to these models. This study aimed to evaluate and to modify remotely‐sensed DEMs for an improved quantification of initial sediment mass changes in an artificially‐created catchment. DEMs were constructed from photogrammetry‐based, airborne (ALS) and ground‐based laser scanning (TLS) data. Regions of differing morphological characteristics and vegetation cover were delineated. Three‐dimensional (3D) models of volume change were established and mass change was derived from these models. DEMs were modified region‐by‐region for rill, interrill and alluvial areas, based on logical and hydro‐geomorphological principles. Additional DEMs were constructed by combining multi‐source, modified data. Models were evaluated by comparison with d‐GPS reference data and by considering sediment budget plausibility. Comprehensive evaluation showed that DEM usability depends on a relation between the technique used to obtain elevation data, surface morphology and vegetation cover characteristics. Photogrammetry‐based DEMs were suited to quantification of change in interrill areas but strongly underestimated surface lowering in erosion rills. TLS DEMs were best suited to rill areas, while ALS DEMs performed best in vegetation‐covered alluvial areas. Agreement with reference data and budget plausibility were improved by modifications to photogrammetry‐ and TLS‐based DEMs. Results suggest that artefacts in DEMs can be reduced and hydro‐geomorphic surface structures can be better represented by applying region‐specific modifications. Photogrammetry‐based DEMs can be improved by combining higher and lower resolution data in defined structural units and applying modifications based on principles given by characteristic hydro‐geomorphic evolution. Results of the critical comparative evaluation of remotely‐sensed elevation data can help to better interpret DEM‐based quantifications of earth‐surface processes. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

12.
Tools for accurately predicting environmental risks, such as the location and spatial extent of potential inundation, are not widely available. A dependence on calibration and a lack of available flood data have prevented the widespread application of existing hydrodynamic methods for predicting the extent of inundation. We use the height above the nearest drainage (HAND) terrain model to develop a simple static approach for mapping the potential extent of inundation that does not depend on flood observations and extends beyond methods for mapping low‐lying areas. While relying on the contour concept, the method utilizes drainage‐normalized topography and flowpaths to delineate the relative vertical distances (drop) to the nearest river. The HAND‐delineated relative drop is an effective distributed predictor of flood potential, which is directly related to the river stage height. We validated the new HAND contour approach using a flood event in Southern Brazil for which high‐resolution maps were available. The results indicated that the flood hazard‐mapping method accurately predicted the inundation extent of the channel carrying the flood wave and the channels influenced by flooding. For channels positioned outside of the flood‐wave area, the method overestimated the actual flood extent. As an original static assessment of floodwaters across the landscape, the HAND contour method could be used to map flood hazards in areas with poor information and could promote the development of new methods for predicting hydrological hazards. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

13.
Advances in remote sensing have enabled hydraulic models to run at fine scale resolutions, producing precise flood inundation predictions. However, running models at finer resolutions increase their computational expense, reducing the feasibility of running the multiple model realizations required to undertake uncertainty analysis. Furthermore, it is possible that precision gained by running fine scale models is smoothed out when treating models probabilistically. The aim of this paper is to determine the level of spatial complexity that is required when making probabilistic flood inundation predictions. The Imera basin, Sicily is used as a case study to assess how changing the spatial resolution of the hydraulic model LISFLOOD‐FP impacts on the skill of conditional probabilistic flood inundation maps given model parameter and boundary condition uncertainties. We find that model performance deteriorates at resolutions coarser than 50 m. This is predominantly caused by changes in flow pathways at coarser resolutions which lead to non‐stationarity in the optimum model parameters at different spatial resolutions. However, although it is still possible to produce probabilistic flood maps that contain a coherent outline of the flood extent at coarser resolutions, the reliability of these maps deteriorates at resolutions coarser than 100 m. Additionally, although the rejection of non‐behavioural models reduces the uncertainty in probabilistic flood maps the reliability of these maps is also reduced. Models with resolutions finer than 50 m offer little gain in performance yet are more than an order of magnitude computationally expensive which can become infeasible when undertaking probabilistic analysis. Furthermore, we show that using deterministic, high‐resolution flood maps can lead to a spurious precision that would be misleading and not representative of the overall uncertainties that are inherent in making inundation predictions. Copyright © 2015 The Authors Hydrological Processes Published by John Wiley & Sons Ltd.  相似文献   

14.
Flood hazard maps at trans‐national scale have potential for a large number of applications ranging from climate change studies, reinsurance products, aid to emergency operations for major flood crisis, among others. However, at continental scales, only few products are available, due to the difficulty of retrieving large consistent data sets. Moreover, these are produced at relatively coarse grid resolution, which limits their applications to qualitative assessments. At finer resolution, maps are often limited to country boundaries, due to limited data sharing at trans‐national level. The creation of a European flood hazard map would currently imply a collection of scattered regional maps, often lacking mutual consistency due to the variety of adopted approaches and quality of the underlying input data. In this work, we derive a pan‐European flood hazard map at 100 m resolution. The proposed approach is based on expanding a literature cascade model through a physically based approach. A combination of distributed hydrological and hydraulic models was set up for the European domain. Then, an observed meteorological data set is used to derive a long‐term streamflow simulation and subsequently coherent design flood hydrographs for a return period of 100 years along the pan‐European river network. Flood hydrographs are used to simulate areas at risk of flooding and output maps are merged into a pan‐European flood hazard map. The quality of this map is evaluated for selected areas in Germany and United Kingdom against national/regional hazard maps. Despite inherent limitations and model resolution issues, simulated maps are in good agreement with reference maps (hit rate between 59% and 78%, critical success index between 43% and 65%), suggesting strong potential for a number of applications at the European scale. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

15.
Surface elevations represented in MODFLOW head-dependent packages are usually derived from digital elevation models (DEMs) that are available at much high resolution. Conventional grid refinement techniques to simulate the model at DEM resolution increases computational time, input file size, and in many cases are not feasible for regional applications. This research aims at utilizing the increasingly available high resolution DEMs for effective simulation of evapotranspiration (ET) in MODFLOW as an alternative to grid refinement techniques. The source code of the evapotranspiration package is modified by considering for a fixed MODFLOW grid resolution and for different DEM resolutions, the effect of variability in elevation data on ET estimates. Piezometric head at each DEM cell location is corrected by considering the gradient along row and column directions. Applicability of the research is tested for the lower Rio Grande (LRG) Basin in southern New Mexico. The DEM at 10 m resolution is aggregated to resampled DEM grid resolutions which are integer multiples of MODFLOW grid resolution. Cumulative outflows and ET rates are compared at different coarse resolution grids. Results of the analysis conclude that variability in depth-to-groundwater within the MODFLOW cell is a major contributing parameter to ET outflows in shallow groundwater regions. DEM aggregation methods for the LRG Basin have resulted in decreased volumetric outflow due to the formation of a smoothing error, which lowered the position of water table to a level below the extinction depth.  相似文献   

16.
Delineation of flood risk hotspots can be considered as one of the first steps in an integrated methodology for urban flood risk management and mitigation. This paper presents a step-by-step methodology in a GIS-based framework for identifying flooding risk hotspots for residential buildings. This is done by overlaying a map of potentially flood-prone areas [estimated through the topographic wetness index (TWI)], a map of residential areas [extracted from a city-wide assessment of urban morphology types (UMT)], and a geo-spatial census dataset. The novelty of this paper consists in the fact that the flood-prone areas (the TWI thresholds) are identified through a maximum likelihood method (MLE) based both on inundation profiles calculated for a specific return period (TR), and on information about the extent of historical flooding in the area of interest. Furthermore, Bayesian parameter updating is employed in order to estimate the TWI threshold by employing the historical extent as prior information and the inundation map for calculating the likelihood function. For different statistics of the TWI threshold, the map of potentially flood-prone areas is overlaid with the map of residential urban morphology units in order to delineate the residential flooding risk urban hotspots. Overlaying the delineated urban hotspots with geo-spatial census datasets, the number of people affected by flooding is estimated. These kind of screening procedures are particularly useful for locations where there is a lack of detailed data or where it is difficult to perform accurate flood risk assessment. In fact, an application of the proposed procedure is demonstrated for the identification of urban flooding risk hotspots in the city of Ouagadougou, capital of Burkina Faso, a city for which the observed spatial extent of a major flood event in 2009 and a calculated inundation map for a return period of 300 years are both available.  相似文献   

17.
Previously we have detailed an application of the generalized likelihood uncertainty estimation (GLUE) procedure to estimate spatially distributed uncertainty in models conditioned against binary pattern data contained in flood inundation maps. This method was applied to two sites where a single consistent synoptic image of inundation extent was available to test the simulation performance of the method. In this paper, we extend this to examine the predictive performance of the method for a reach of the River Severn, west‐central England. Uniquely for this reach, consistent inundation images of two major floods have been acquired from spaceborne synthetic aperture radars, as well as a high‐resolution digital elevation model derived using laser altimetry. These data thus allow rigorous split sample testing of the previous GLUE application. To achieve this, Monte Carlo analyses of parameter uncertainty within the GLUE framework are conducted for a typical hydraulic model applied to each flood event. The best 10% of parameter sets identified in each analysis are then used to map uncertainty in flood extent predictions using the method previously proposed for both an independent validation data set and a design flood. Finally, methods for combining the likelihood information derived from each Monte Carlo ensemble are examined to determine whether this has the potential to reduce uncertainty in spatially distributed measures of flood risk for a design flood. The results show that for this reach and these events, the method previously established is able to produce sharply defined flood risk maps that compare well with observed inundation extent. More generally, we show that even single, poor‐quality inundation extent images are useful in constraining hydraulic model calibrations and that values of effective friction parameters are broadly stationary between the two events simulated, most probably reflecting their similar hydraulics. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

18.
This paper investigates the development of flood hazard and flood risk delineations that account for uncertainty as improvements to standard floodplain maps for coastal watersheds. Current regulatory floodplain maps for the Gulf Coastal United States present 1% flood hazards as polygon features developed using deterministic, steady‐state models that do not consider data uncertainty or natural variability of input parameters. Using the techniques presented here, a standard binary deterministic floodplain delineation is replaced with a flood inundation map showing the underlying flood hazard structure. Additionally, the hazard uncertainty is further transformed to show flood risk as a spatially distributed probable flood depth using concepts familiar to practicing engineers and software tools accepted and understood by regulators. A case study of the proposed hazard and risk assessment methodology is presented for a Gulf Coast watershed, which suggests that storm duration and stage boundary conditions are important variable parameters, whereas rainfall distribution, storm movement, and roughness coefficients contribute less variability. The floodplain with uncertainty for this coastal watershed showed the highest variability in the tidally influenced reaches and showed little variability in the inland riverine reaches. Additionally, comparison of flood hazard maps to flood risk maps shows that they are not directly correlated, as areas of high hazard do not always represent high risk. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

19.
Predicting and mapping high water table elevation in coastal landscapes is critical for both science application projects like inundation risk analysis and engineering projects like pond design and maintenance. Previous studies of water table mapping focused on the application of geostatistical methods, which cannot predict values beyond an observation spatial domain or generate an ideal pattern for regions with sparse measurements. In this study, we evaluated the multiple linear regression (MLR) and support vector machine (SVM) techniques for high water table prediction and mapping using fine spatial resolution lidar-derived Digital Elevation Model (DEM) data, and designed an application protocol of these two techniques for high water table mapping in a coastal landscape where groundwater, tide, and surface water are related. Testing results showed that SVM largely improved the high water table prediction with a mean absolute error (MAE) of 1.22 feet and root mean square error (RMSE) of 2.22 feet compared to the application of the ordinary Kriging method which could not generate a reasonable water table. MLR was also promising with a MAE of around 2 feet and RMSE of around 3 feet. The study suggests that both MLR and SVM are valuable alternatives to estimate high water table elevation in Florida. Fine resolution lidar DEMs are beneficial for high water table prediction and mapping.  相似文献   

20.
The capability of a simple kinematic‐storage model (KSM) is analysed to be used as a tool for a Decision Support System for the evaluation of probability inundation maps in near real time in poorly gauged areas. KSM simulates the floodplain as a storage and assumes no exchange of momentum with the channel. For the in‐bank flow, the storage is modified through a coefficient for taking the variations of channel cross sections into account. The generalized likelihood uncertainty estimation approach is used for addressing the probability flood maps along with their associated uncertainties. The model is tested on two river reaches along the Tiber River in Central Italy where observed inundation maps are available for two recent flood events. Despite the inherent uncertainties present in the input data and in the model structure, the results show that the model reproduces reasonably well, in terms of both precision and accuracy, the observed inundated areas. Tests were performed at different digital elevation model resolutions, showing a small effect of the geometry on the maximum performance obtained. The very low computational times, the parsimony of the model and its low sensitivity to the quality of the geometry representation of the channel and the floodplain makes KSM very appealing for flood forecasting and early warning system applications in poorly gauged and inaccessible areas. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号