共查询到20条相似文献，搜索用时 187 毫秒
1.
为研究不同设计参数对曲线梁桥地震响应的影响以指导结构抗震设计,对不同支承约束曲线梁桥地震响应及地震需求敏感性进行分析。采用增量动力分析（IDA）方法对比分析了不同支承约束曲线梁桥的结构地震响应变化趋势;采用Tornado图形法对不同结构参数影响程度进行了排序,找出了对结构地震需求影响显著的参数。结果表明:采用板式橡胶支座桥梁因支座易发生滑移而导致上部结构位移较大,但降低了下部结构响应,设置固定墩后,下部结构损伤显著增加;对于采用板式橡胶支座和铅芯橡胶支座的曲线梁桥,墩高及跨径对墩底曲率需求影响较大,而对于固定墩为墩梁固结形式和采用盆式橡胶支座的曲线梁桥,跨径及跨数对墩底曲率需求影响较大;对于采用不同支承约束的曲线梁桥,墩高和曲率半径对桥台位移需求影响较大,仅次于地震动参数PGA。 相似文献
2.
建立双向地震作用下层间隔震双向偏心结构侧扭耦联分析模型;考虑上部结构及下部结构的弹塑性模型,隔震支座采用双向耦合非线性Bouc-wen模型模拟;分析偏心参数对层间隔震双向偏心结构的影响规律;评价双向地震作用下我国抗震规范给出的扭转影响系数静力预测值的准确性。结果表明,双向地震作用下设置中间柔性隔震层可以减小上\,下部结构扭转的耦连效应;下部结构存在双向偏心会对隔震层和下部结构扭转反应带来不利影响;LRB耦合效应对层间隔震地震响应影响较小;当下部结构偏心率较大时现行规范计算扭转系数偏于不安全。 相似文献
3.
为研究设计地震作用下铁路梁桥支座水平地震力按静力法计算的准确性和适用性,以一墩高为5～20 m、跨径为32 m的简支梁桥圆端形重力式桥墩为研究对象,建立单墩抗震模型,采用反应谱法分析不同场地条件下支座的水平地震力,探讨设计地震作用下桥墩截面的合理刚度取值。分析结果表明设计地震下桥墩均处于开裂状态,应以开裂截面刚度作为反应谱计算的截面刚度;静力法计算支座水平地震力会造成设计值偏大或偏小;桥墩越矮,场地条件越差,动力效应越明显,建议支座水平地震力采用动力法进行分析。 相似文献
4.
强震作用下隔震曲线梁桥会产生较大的弹塑性变形,需要采取一定的控制措施以保证其安全性。采用经典的Bouc-Wen模型,建立考虑上部结构偏心的隔震曲线梁桥的非线性动力方程,求解罕遇地震作用下结构的动力响应。针对隔震曲线梁桥罕遇地震作用下产生的较大弹塑性变形,建立隔震曲线梁桥的非线性振动控制方程,将该方程等效线性化后采用序列最优控制算法(SOC)和经典线性最优控制(COC)对桥梁进行振动控制研究。结果表明：在罕遇地震下,隔震曲线梁桥的下部结构与隔震层都已屈服进入塑性阶段,且有少量的残余位移产生;序列最优控制算法和经典线性最优控制都能有效地减小隔震曲线梁桥弹塑性状态下的平动位移与残余位移,并有效抑制曲线桥的扭转效应,其中序列最优控制算法较经典最优控制更能显著削减隔震曲线梁桥的峰值响应。 相似文献
5.
采用反应位移法进行地下结构抗震计算时,关键是确定土体的弹簧系数,弹簧系数的取值直接影响计算结果。在现有的静力有限元求解弹簧系数方法的基础上,通过不同的施力方式共设计了6种静力有限元求解弹簧弹簧系数的方法,并对这6种计算方法进行对比分析计算。结果表明,整体和整体同时求解径向和切向弹簧系数这两种方法的计算结果偏于危险;单独和单独同时求解水平和垂直向弹簧系数这两种方法的计算精度最好;整体和整体同时求解水平和垂直向弹簧系数这两种方法的计算结果偏于安全。 相似文献
6.
采用反应位移法进行地下结构抗震计算时,关键是确定土体的弹簧系数,弹簧系数的取值直接影响计算结果。在现有的静力有限元求解弹簧系数方法的基础上,通过不同的施力方式共设计了6种静力有限元求解弹簧弹簧系数的方法,并对这6种计算方法进行对比分析计算。结果表明,整体和整体同时求解径向和切向弹簧系数这两种方法的计算结果偏于危险;单独和单独同时求解水平和垂直向弹簧系数这两种方法的计算精度最好;整体和整体同时求解水平和垂直向弹簧系数这两种方法的计算结果偏于安全。 相似文献
7.
曲线桥梁在役期间可能面临地震灾害,导致结构损坏甚至坍塌,为了评估在役桥梁的抗震性能,提出基于损伤分析的曲线梁桥抗震性能评估方法。建立旧曲线梁桥有限元模型,基于损伤分析的原理,提出适合曲线梁桥地震响应特性的构件损伤模型,在全桥有限元模型中输入不同类型地震动,计算各构件的损伤指数,并结合旧桥检算系数,由各构件损伤指数综合得到桥梁的整体损伤指数。结果表明:不同地震动下主梁会发生碰撞破坏,桥梁两端的支座容易发生移位,桥墩沿横桥向或顺桥向均会产生位移;不同地震动对主梁、支座、桥墩等构件造成的损害程度有较大差异,各构件的地震响应会影响桥梁整体结构的抗震性能,其中桥墩对桥梁整体抗震性能的影响最大,桥墩位移超过极限值可能导致倒塌;主梁反复碰撞会加剧桥梁的破坏程度,桥梁两端支座在地震作用下更容易发生损坏。 相似文献
8.
9.
碰撞作用直接影响到桥梁不同构件的地震响应,是桥梁抗震研究中一直关注的问题。针对地震作用下曲线梁桥因主梁面内转动而发生主梁与切向桥台和径向挡块碰撞的现象,以1座3跨预应力混凝土连续梁桥为例,采用非线性时程分析方法,对曲线连续梁桥的双向碰撞作用影响进行研究,并分析了不同减撞措施的效果。结果表明:考虑双向碰撞作用后,下部结构响应有明显增加,主梁转动现象变得复杂,曲线梁桥地震响应分析中应通过建立精细化模型来考虑主梁双向碰撞作用的影响;在切向桥台处设置限位拉锁装置能起到较好的减轻双向碰撞作用的影响,以及采用减隔震设计后,减撞效果更明显,桥梁抗震性能明显改善,但合理减撞措施设计参数应结合曲线梁桥约束体系及结构设计参数进行体系分析确定。 相似文献
10.
11.
利用CHAMP数据恢复重力场的解算方法分为时域法和空域法.本文首先介绍了这两种方法恢复CHAMP重力场的基本原理和算法,分析了它们的优缺点.针对空域法中的延拓误差和格网化误差进行了讨论.计算表明:延拓误差中的截断误差部分影响量级约0.001 m2·s-2(均方误差意义下),最大误差仅为0.11 m2·s-2,可完全忽略;延拓误差中的参考重力场模型误差影响随参考场选取的不同而有所差异,整体而言小于0.1 m2·s-2,但最大误差可达1.3 m2·s-2,采用高精度的参考重力场模型能大大减小延拓误差影响.目前最常用的格网化方法包括加权平均方法和最小二乘配置方法,计算表明,利用30天的CHAMP数据进行2°×2°格网化处理,加权平均法的格网化误差在0.13 m2·s-2量级,最大误差可达1.58 m2·s-2,而最小二乘配置法的格网化误差在0.006 m2·s-2量级,最大误差仅为0.15 m2·s-2,明显优于加权平均法.文章最后对时域法和以快速最小二乘配置(FSC)为代表的空域法恢复60阶次的CHAMP重力场的精度进行了比较,结果表明:两种方法的得到的重力场模型精度相差不大,整体而言,时域法略优于空域法. 相似文献
12.
Effect of ground motion selection methods on seismic collapse fragility of RC frame buildings 总被引：1，自引：0，他引：1 
下载免费PDF全文
下载免费PDF全文 Variation in the seismic collapse fragility of reinforced concrete frame buildings predicted using different ground motion (GM) selection methods is investigated in this paper. To simulate the structural collapse, a fiber‐element modelling approach with path‐dependent cyclic nonlinear material models that account for concrete confinement and crushing, reinforcement buckling as well as low cycle fatigue is used. The adopted fiber analysis approach has been found to reliably predict the loss in vertical load carrying capacity of structural components in addition to the sidesway mode of collapse due to destabilizing P–Δ moments at large inelastic deflections. Multiple stripe analysis is performed by conducting response history analyses at various hazard levels to generate the collapse fragility curves. To select GMs at various hazard levels, two alternatives of uniform hazard spectrum (UHS), conditional mean spectrum (CMS) and generalized conditional intensity measure (GCIM) are used. Collapse analyses are repeated based on structural periods corresponding to initial un‐cracked stiffness and cracked stiffness of the frame members. A return period‐based intensity measure is then introduced and applied in estimating collapse fragility of frame buildings. In line with the results of previous research, it is shown that the choice of structural period significantly affects the collapse fragility predictions. Among the GM selection methods used in this study, GCIM and CMS methods predict similar collapse fragilities for the case study building investigated herein, and UHS provides the most conservative prediction of the collapse capacity, with approximately 40% smaller median collapse capacity compared to the CMS method. The results confirm that collapse probability prediction of buildings using UHS offers a higher level of conservatism in comparison to the other selection methods. Copyright © 2017 John Wiley & Sons, Ltd. 相似文献
13.
声波时差测井数据的精度直接关系到油气层评价、油气储量计算和合成地震记录等的质量.本文通过数值模拟首次讨论了扩径段厚度对双发双收声系时差记录的影响程度.在径向扩径量一定条件下,当井轴方向的扩径厚度达到某一个特定数值时,时差测量误差最大;而大于或者小于该扩径厚度特定值时,测量误差都会变小.当井径大于或者等于扩径临界值时,接收探头记录的首波走时中将含有扩径段泥浆波走时的贡献.首次发现使扩径临界值取得最大值的井轴方向扩径厚度特征值.远离该厚度特征值,接收含有扩径段泥浆波走时的首波径向扩径临界值都会变小.第一次给出有关接收扩径段泥浆波走时的扩径临界值图版. 相似文献
14.
The performance of force-based and displacement-based seismic assessment methods for the life-safety limit state check of out-of-plane loaded unreinforced masonry walls is evaluated on the basis of refined numerical simulations. For this purpose, a discrete element model of a vertically spanning wall is built and validated against experimental results from static and dynamic test conditions. The model is then analysed for a large range of wall configurations. For each configuration, a static pushover analysis and a series of incremental dynamic analyses are run, the latter permitting to determine the capacity of the wall under dynamic loading. The accuracy of the assessment methods in predicting the acceleration at which the walls collapse is evaluated. It is found that the displacement-based method is more accurate, robust, and safe than the force-based method. The comparison also shows that for walls characterised by a relatively high ratio of axial load to Euler's critical load, both assessment methods lead to an overestimation of the wall capacity. As a remedy, a modification to the methods based on a recently developed mechanical model is put forward and tested. For the force-based method, it is additionally suggested to set for walls with relatively high overburden ratios the behaviour factor equal to 1. To ensure reproducibility of this study, all input and output files of the numerical simulations are made publicly available. 相似文献
15.
反馈迭代法压制表面多次波效果分析 总被引：3，自引：0，他引：3
地震数据处理通常假定反射数据仅由一次波组成,地震勘探资料中的表面多次波通常被视为相干噪音予以压制.基于波动方程预测的反馈迭代法为数据驱动的方法,可有效压制复杂地下介质的表面多次波,通常可由级数展开法和迭代法两种方法实现.文中分别从理论阐述以及应用效果分析方面对基于波动方程预测的反馈迭代法的两种实现途径进行研究,并采用GPU/CPU协同并行加速计算预测表面多次波,改善以往CPU计算效率低的状况.文中对含表面多次波的炮数据和复杂的SMAART模型进行了计算,并将利用级数展开法与迭代法压制表面多次波的效果进行对比分析,结果表明,迭代形式反馈迭代法压制表面多次波的方法效果更佳.由于实现迭代法和级数展开法需要完成的自适应匹配相减的次数不同,迭代法的计算成本略高于级数展开法. 相似文献
16.
重力卫星可以在相同误差尺度下对全球质量变化进行连续重复观测,并在近十余年来取得了巨大成功,探索重力卫星数据精化处理方法和相关应用研究具有重要意义.本文基于三维加速度点质量模型法的基本原理,进一步发展建立了时变重力场模型球谐位系数的变化和地面点质量变化的关系,可有效考虑地表质量变化导致的负荷形变的影响;引入等权形式、线性形式、指数形式和高斯形式的空间约束方法处理南北条带噪声和向下延拓导致的病态问题,并与零阶Tikhonov正则化方法进行对比分析.采用模拟数据和一个月的实测GRACE时变重力场模型计算全球质量变化,对三维加速度点质量模型法和几种空间约束方法进行对比分析验证.计算结果表明,对于3°等面积的全球格网质量点,高斯和指数形式空间约束方法的最优相关距离约为500km,等权和线性形式空间约束方法的最优相关距离约为600km,各方法均可有效处理条带噪声的影响,四种空间约束方法的计算效果优于零阶Tikhonov正则化方法,本文的相关方法为进一步利用三维加速度点质量模型法监测全球质量变化提供了借鉴. 相似文献
17.
表面多次波是一种相干干扰，在海洋地球物理勘探中表面多次波尤为明显.本文给出了表面多次波衰减方法的研究现状的系统阐述，并分析了表面多次波衰减研究的发展趋势.表面多次波衰减主要有滤波法和波动理论方法.对于滤波法给出了广泛应用的抛物Radon变换法的实例，指出了抛物Radon 变换法存在滤波时能量泄漏的问题.同时本文分析了基于波动理论的处理优势和存在的问题，该方法可以处理任意介质的情形，但是对于数据的采集要求比较严格，另外在进行表面多次波衰减处理以前，要进行一系列的预处理，这些预处理的误差直接决定着多次波衰减的效果.最后，本文给出了表面多次波衰减的发展趋势——将滤波法和波动理论法结合来实现多次波的衰减.两类方法如何有效地结合是该类方法一个重要的研究方向. 相似文献
18.
In endurance time(ET) method structures are subjected to a set of predesigned intensifying excitations. These excitations are produced in a way that their response spectrum, while complying with a specifi ed spectrum, intensifi es with time so they can be used approximately to simulate the average effects of several ground motions scaled to different intensities. In this paper applicability of the ET method for evaluating collapse potential of buildings is investigated. A set of four steel moment frames is used for collapse assessment. The process of using ET method in collapse evaluation is explained and the results are compared with incremental dynamic analysis(IDA) results. It is shown that although the computational effort using the ET method is much less than the IDA analysis, the results of both methods are consistent. Finally collapse fragility curves using ET and IDA methods are produced and it is shown that the probabilities of collapse in different hazard levels are also consistent. 相似文献
19.
Earthquake-induced building collapse and progressive collapse due to accidental local failure of vertical components are the two most common failure modes of reinforced concrete (RC) frame structures. Conventional design methods usually focus on the design requirements of a specific hazard but neglect the interactions between different designs. For example, the progressive collapse design of an RC frame often yields increased reinforcement and flexural strength of the beams. As a result, the seismic design principle of “strong-column-weak-beam” may be violated, which may lead to unfavorable failure modes and weaken the seismic performance. To avoid these adverse effects of the progressive collapse design on the seismic resistance of RC frames, a novel structural detailing is proposed in this study. The proposed detailing technique intends to concurrently improve the seismic and progressive collapse performances of an RC frame by changing the layout of the newly added longitudinal reinforcement against progressive collapse without introducing any additional reinforcement. A six-story RC frame is used as the prototype building for this investigation. Both cyclic and progressive collapse tests are conducted to validate the performance of the proposed structural detailing. Based on the experimental results, detailed finite element (FE) models of the RC frame with different reinforcement layouts are established. The seismic and progressive collapse resistances of different models are compared based on the incremental dynamic analysis (IDA) and nonlinear dynamic alternate path (AP) methods, respectively. The results indicate that the proposed structural detailing can effectively resolve the conflict between the seismic and progressive collapse designs. 相似文献