首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 515 毫秒
1.
High-pressure Raman studies of methane hydrate were performed using a diamond anvil cell in the pressure range of 0.1–86 GPa at room temperature. Raman spectra of the methane molecules revealed that new softened intramolecular vibration mode of ν 1 appeared at 17 GPa and that the splitting of vibration mode of ν 3 occurred at 15 GPa. The appearance of these two modes indicates that an intermolecular attractive interaction increases between the methane molecules and the host water molecules and between the neighboring methane molecules. These interactions might result in the exceptional stability of a high-pressure structure, a filled ice Ih structure (FIIhS) for methane hydrate, up to 40 GPa. At 40 GPa, a clear change in the slope of the Raman shift versus pressure occurred, and above 40 GPa the Raman shift of the vibration modes increased monotonously up to 86 GPa. A previous XRD study showed that the FIIhS transformed into another new high-pressure structure at 40 GPa. The change in the Raman spectra at 40 GPa may be induced by the transition of the structure.  相似文献   

2.
In situ Raman spectra of hydrous wadsleyite (β-Mg2SiO4) with ~1.5 wt% H2O, synthesized at 18 GPa and 1,400°C, have been measured in an externally heated diamond anvil cell up to 15.5 GPa and 673 K. With increasing pressure (at room temperature), the three most intense bands at ~549, 720 and 917 cm−1 shift continuously to higher frequencies, while with increasing temperature at 14.5 GPa, these bands generally shift to lower frequencies. The temperature-induced frequency shifts at 14.5 GPa are significantly different from those at ambient pressure. Moreover, two new bands at ~714 and ~550 cm−1 become progressively significant above 333 and 553 K, respectively, and disappear upon cooling to room temperature. No corresponding Raman modes of these two new bands were reported for wadsleyite at ambient conditions, and they are thus probably related to thermally activated processes (vibration modes) at high-pressure and temperature conditions.  相似文献   

3.
K-lingunite is a high-pressure modification of K-feldspar that possesses the tetragonal hollandite structure. Variations of the Raman spectra of K-lingunite were studied up to ~31.5 GPa at room temperature, and in the range 79–823 K at atmospheric pressure. The Raman frequencies of all bands were observed to increase with increasing pressure, and decrease with increasing temperature for K-lingunite. This behavior is in line with those observed for most of other materials. New sharp Raman bands appear at pressures greater than 13–15 GPa, suggesting a phase transition in K-lingunite with increasing pressure. The transition is reversible when pressure was released. The appearance of these new Raman bands may correspond to the phase transition revealed earlier at around 20 GPa by X-ray diffraction studies. Instead of transforming back to its stable minerals, such as orthoclase, microcline or sanidine, K-lingunite became amorphous in the temperature range 803–823 K at atmospheric pressure.  相似文献   

4.
The high-pressure behavior of the lattice elasticity of spodumene, LiAlSi2O6, was studied by static compression in a diamond-anvil cell up to 9.3 GPa. Investigations by means of single-crystal XRD and Raman spectroscopy within the hydrostatic limits of the pressure medium focus on the pressure ranges around ~3.2 and ~7.7 GPa, which have been reported previously to comprise two independent structural phase transitions. While our measurements confirm the well-established first-order C2/c–P21/c transformation at 3.19 GPa (with 1.2% volume discontinuity and a hysteresis between 0.02 and 0.06 GPa), both unit-cell dimensions and the spectral changes observed in high-pressure Raman spectra give no evidence for structural changes related to a second phase transition. Monoclinic lattice parameters and unit-cell volumes at in total 59 different pressure points have been used to re-calculate the lattice-related properties of spontaneous strain, volume strain, and the bulk moduli as a function of pressure across the transition. A modified Landau free energy expansion in terms of a one component order parameter has been developed and tested against these experimentally determined data. The Landau solution provides a much better reproduction of the observed anomalies than any equation-of-state fit to data sets truncated below and above P tr, thus giving Landau parameters of K 0 = 138.3(2) GPa, K′ = 7.46(5), λ V  = 33.6(2) GPa, a = 0.486(3), b = −29.4(6) GPa and c = 551(11) GPa.  相似文献   

5.
 The Raman spectra of synthetic α-Co2SiO4 and α-Ni2SiO4 olivines have been studied at room temperature and various pressures. All the Raman frequencies of the two olivines increase with increasing pressure, and most of the frequency–pressure plots obtained under both quasi- and nonhydrostatic conditions are nonlinear. It has been found that the average pressure derivative of Raman frequencies of the lattice modes in both Co- and Ni-olivines is smaller than that of the internal modes of SiO4, indicating that the distortion of SiO4 tetrahedra under static compression may be more severe than that of MO6 octahedra. In addition, four new Raman bands were observed in Ni-olivine under nonhydrostatic compression and above 30 GPa. This result suggests that a new phase of Ni-olivine should be formed at 30 GPa or amorphization may occur at still higher pressure. Received: 11 July 2000 / Accepted: 19 December 2000  相似文献   

6.
A neutron powder diffraction study of hydrogenated and deuterated brucite was conducted at ambient temperature and at pressures up to 9 GPa, using a Paris–Edinburgh high-pressure cell at the WAND instrument of the ORNL High Flux Isotope Reactor. The two materials were synthesized by the same method and companion measurements of neutron diffraction were conducted under the same conditions. Our refinement results show that the lattice-parameters of the a axis, parallel to the sheets of Mg–O octahedra, decrease only slightly with pressure with no effect of H–D substitution. However, the c axis of Mg(OD)2 is shorter and may exhibit greater compressibility with pressure than that of Mg(OH)2. Consequently, the unit-cell volume of deuterated brucite is slightly, but systematically smaller than that of hydrogenated brucite. When fitted to a third-order Birch–Murnaghan equation in terms of the normalized unit-cell volume, values of the bulk modulus for hydrogenated and deuterated brucite (K 0 = 39.0 ± 2.8 and 40.4 ± 1.3 GPa, respectively) are, however, indistinguishable from each other within the experimental errors. The measured effect of H–D substitution on the unit-cell volume also demonstrates that brucite (and other hydrous minerals) preferentially incorporate deuterium over hydrogen under pressure, suggesting that the distribution of hydrogen isotopes in deep-earth conditions may differ significantly from that in near-surface environments.  相似文献   

7.
The infrared spectrum of CaAl2Si2O7 · H2O-lawsonite, has been characterized to pressures of 20 GPa at 300 K. Our results constrain the response to compression of the silicate tetrahedra, hydroxyl units, and water molecules in this material. The asymmetric and symmetric stretching and bending vibrations of the Si2O7 groups (at zero pressure frequencies between 600 and 1000 cm−1) increase in frequency with pressure at rates between 3.6 and 5.9 cm−1/GPa. All silicate modes appear to shift continuously with pressure to 20 GPa, although the lowest frequency stretching vibration becomes unresolvable above 18 GPa, and a splitting of the main bending vibration is observed near this pressure. The O-H stretches of the hydroxyl units exhibit a discontinuity in their mode shifts at ∼8–9 GPa, which we interpret to be produced by a pressure-induced change in hydrogen bonding. The stretching and bending vibrations of the water molecule are relatively unaffected by compression to 20 GPa, thus demonstrating that the structural cavities in which water molecules reside are relatively rigid. Significant changes in the amplitude of the O-H stretches of the hydroxyl and water units are observed at this pressure as well; nevertheless, our results demonstrate that the dominant structural units in lawsonite persist metastably at 300 K with only modest structural modifications well beyond the known stability field of this phase. Received: 10 July 1998 / Revised, accepted: 23 October 1998  相似文献   

8.
The effects of pressure on the dehydration of gypsum materials were investigated up to 633 K and 25 GPa by using Raman spectroscopy and synchrotron X-ray diffraction with an externally heated diamond anvil cell. At 2.5 GPa, gypsum starts to dehydrate around 428 K, by forming bassanite, CaSO4 hemihydrate, which completely dehydrates to γ-anhydrite at 488 K. All the sulphate modes decrease linearly between 293 and 427 K with temperature coefficients ranging from −0.119 to −0.021 cm−1 K−1, where an abrupt change in the ν3 mode and in the OH-stretching region indicates the beginning of dehydration. Increasing the temperature to 488 K, the OH-stretching modes completely disappear, marking the complete dehydration and formation of γ-anhydrite. Moreover, the sample changes from transparent to opaque to transparent again during the dehydration sequence gypsum-bassanite-γ-anhydrite, which irreversibly transforms to β-anhydrite form at 593 K. These data compared with the dehydration temperature at room pressure indicate that the dehydration temperature increases with pressure with a ΔP/ΔT slope equal to 230 bar/K. Synchrotron X-ray diffraction experiments show similar values of temperature and pressure for the first appearance of bassanite. Evidence of phase transition from β-anhydrite structure to the monazite type was observed at about 2 GPa under cold compression. On the other hand at the same pressure (2 GPa and 633 K), β-anhydrite was found, indicating a positive Clausis-Clayperon slope of the transition. This transformation is completely reversible as showed by the Raman spectra on the sample recovered after phase transition.  相似文献   

9.
Raman spectra of monoclinic Fo90 hydrous wadsleyite with 2.4 wt% H2O have been measured in a diamond-anvil cell with helium as a pressure-transmitting medium to 58.4 GPa at room temperature. The most intense, characteristic wadsleyite modes, the Si–O–Si symmetric stretch at 721 cm−1 and the symmetric stretch of the SiO3 unit at 918 cm−1, shift continuously to 58.4 GPa showing no evidence of a first order change in the crystal structure despite compression well beyond the stability field of wadsleyite in terms of pressure. The pressure dependence of these two modes is nearly identical for Fo90 hydrous and Fo100 anhydrous wadsleyite. A striking feature in the high-pressure Raman spectra of Fo90 hydrous wadsleyite is the appearance of new Raman modes above 9 GPa in the mid-frequency range (300–650 cm−1 at 1-bar and shifted to 500–850 cm−1 at 58.4 GPa) accompanied by a significant growth in their intensities under further compression. In the OH stretching frequency range Fo90 hydrous wadsleyite exhibits a larger number of modes than the Mg end-member phase. The higher number of modes may be due to either additional protonation sites or simply that we observe a different subset of all possible OH modes for each sample. The high-pressure behaviour of the OH stretching modes of Fo90 and Fo100 hydrous wadsleyite is consistent: OH stretching modes with frequencies <3,530 cm−1 decrease with increasing pressure whereas the higher-frequency OH modes show a close to constant pressure dependence to at least 13.2 GPa. The approximately constant pressure dependence of the OH modes above 3,530 cm−1 is consistent with protons being located at the O1···O edges around M3.  相似文献   

10.
We predict the IR-TO, IR-LO and Raman modes (wave numbers and intensities) of magnesite (MgCO3) up to 50 GPa, at T = 0 K, using the density-functional perturbation theory up to a third order perturbation, under the harmonic assumption. The predicted IR-TO and Raman mode wave numbers, the mode Grüneisen parameters and the Davydov splittings are systematically compared with experimental data for all modes up to the pressures of 10–30 GPa and for some modes up to 50 GPa. Existing experiments allow extending this comparison only to IR-LO wave numbers of the E u (ν3) asymmetric-stretch mode, confirming the odd experimental behavior of this mode at very high pressures. Predicted IR-TO, IR-LO and Raman intensities up to 50 GPa are just tabulated, but data are missing for their comparison with precise experiments. However, the generally good agreement observed between numerical results and experimental data, when their comparison is possible, suggests that first-principles methods are a major help to predict the entire spectrum up to very high pressures.  相似文献   

11.
 Raman spectra of a single-crystal fragment of hydrous γ-Mg2SiO4, synthesized in a multianvil press, have been measured in a diamond-anvil cell with helium as pressure-transmitting medium to 56.5 GPa at room temperature. All five characteristic spinel Raman modes shift continuously up to the highest pressure, showing no evidence for a major change in the crystal structure despite compression well beyond the stability field of ringwoodite in terms of pressure. At pressures above ∼30 GPa a new mode on the low-frequency site of the two silicate-stretching modes is clearly identifiable, indicating a modification in the spinel structure which is reversible on pressure release. The frequency of the new mode (802 cm−1 extrapolated to 1 bar) suggests the presence of Si–O–Si linkages and/or a partial increase in the coordination of Si. Direct determination of the subtle structural change causing the new Raman mode would require high-pressure, single-crystal synchrotron X-ray diffraction experiments. The Raman modes of hydrous and anhydrous Mg-end-member ringwoodite are nearly identical up to 20 GPa, suggesting that protonation has only minor effect on the lattice dynamics over the entire pressure stability range for ringwoodite in the mantle. Received: 7 December 2001 / Accepted: 16 April 2002  相似文献   

12.
The pressure responses of portlandite and the isotope effect on the phase transition were investigated at room temperature from single-crystal Raman and IR spectra and from powder X-ray diffraction using diamond anvil cells under quasi-hydrostatic conditions in a helium pressure-transmitting medium. Phase transformation and subsequent peak broadening (partial amorphization) observed from the Raman and IR spectra of Ca(OH)2 occurred at lower pressures than those of Ca(OD)2. In contrast, no isotope effect was found on the volume and axial compressions observed from powder X-ray diffraction patterns. X-ray diffraction lines attributable to the high-pressure phase remained up to 28.5 GPa, suggesting no total amorphization in a helium pressure medium within the examined pressure region. These results suggest that the H–D isotope effect is engendered in the local environment surrounding H(D) atoms. Moreover, the ratio of sample-to-methanol–ethanol pressure medium (i.e., packing density) in the sample chamber had a significant effect on the increase in the half widths of the diffraction lines, even at pressures below the hydrostatic limit of the pressure medium.  相似文献   

13.
 We present Raman and infrared spectra of gypsum to 21 GPa at 300 K. Our measurements encompass the internal modes of the (SO4)−4 group that lie between 400 and 1150 cm−1, hydroxyl-stretching vibrations between 3200 and 3600 cm−1, and a libration and bending vibrations of the molecular H2O group. All vibrations of the sulfate group have positive pressure shifts, while the hydroxyl-stretching and -bending vibrations have a mixture of positive and negative pressure shifts: the effect of pressure on the hydrogen bonding of the water molecule thus appears to be complex. Near 5 GPa, the two infrared-active bending vibrations of the water molecule coalesce, and the morphology of the hydroxyl-stretching region of the spectrum shifts dramatically. This behavior is consistent with a pressure-induced phase transition in gypsum in the vicinity of 5–6 GPa, which is observed to be reversible on decompression to zero pressure. The spectral observations are consistent with the onset of increased disorder in the position of the water molecule in gypsum: the sulfate vibrations are largely unaffected by this transition. The Raman-active symmetric stretch of the sulfate group undergoes an apparent splitting near 4 GPa, which is interpreted to be produced by Fermi resonance with an overtone of the symmetric bending vibration. The average mode Grüneisen parameter of the 20 vibrational modes we sample is less than 0.05, in contrast to the bulk thermal Grüneisen parameter of 1.20. Accordingly, the vibrations of both water and sulfate units within gypsum are highly insensitive to volumetric compaction. Therefore, in spite of the changes in the bonding of the water unit near 5 GPa, metastably compressed gypsum maintains strongly bound molecular-like units to over 20 GPa at 300 K. Received: 31 July 2000 / Accepted: 5 April 2001  相似文献   

14.
Phase relations of phlogopite with magnesite from 4 to 8 GPa   总被引：2，自引：2，他引：0  
To evaluate the stability of phlogopite in the presence of carbonate in the Earth’s mantle, we conducted a series of experiments in the KMAS–H2O–CO2 system. A mixture consisting of synthetic phlogopite (phl) and natural magnesite (mag) was prepared (phl90-mag10; wt%) and run at pressures from 4 to 8 GPa at temperatures ranging from 1,150 to 1,550°C. We bracketed the solidus between 1,200 and 1,250°C at pressures of 4, 5 and 6 GPa and between 1,150 and 1,200°C at a pressure of 7 GPa. Below the solidus, phlogopite coexists with magnesite, pyrope and a fluid. At the solidus, magnesite is the first phase to react out, and enstatite and olivine appear. Phlogopite melts over a temperature range of ~150°C. The amount of garnet increases above solidus from ~10 to ~30 modal% to higher pressures and temperatures. A dramatic change in the composition of quench phlogopite is observed with increasing pressure from similar to primary phlogopite at 4 GPa to hypersilicic at pressures ≥5 GPa. Relative to CO2-free systems, the solidus is lowered such, that, if carbonation reactions and phlogopite metasomatism take place above a subducting slab in a very hot (Cascadia-type) subduction environment, phlogopite will melt at a pressure of ~7.5 GPa. In a cold (40 mWm−2) subcontinental lithospheric mantle, phlogopite is stable to a depth of 200 km in the presence of carbonate and can coexist with a fluid that becomes Si-rich with increasing pressure. Ascending kimberlitic melts that are produced at greater depths could react with peridotite at the base of the subcontinental lithospheric mantle, crystallizing phlogopite and carbonate at a depth of 180–200 km.  相似文献   

15.
To examine the effect of KCl-bearing fluids on the melting behavior of the Earth’s mantle, we conducted experiments in the Mg2SiO4–MgSiO3–H2O and Mg2SiO4–MgSiO3–KCl–H2O systems at 5 GPa. In the Mg2SiO4–MgSiO3–H2O system, the temperature of the fluid-saturated solidus is bracketed between 1,200–1,250°C, and both forsterite and enstatite coexist with the liquid under supersolidus conditions. In the Mg2SiO4–MgSiO3–KCl–H2O systems with molar Cl/(Cl + H2O) ratios of 0.2, 0.4, and 0.6, the temperatures of the fluid-saturated solidus are bracketed between 1,400–1,450°C, 1,550–1,600°C, and 1,600–1,650°C, respectively, and only forsterite coexists with liquid under supersolidus conditions. This increase in the temperature of the solidus demonstrates the significant effect of KCl on reducing the activity of H2O in the fluid in the Mg2SiO4–MgSiO3–H2O system. The change in the melting residues indicates that the incongruent melting of enstatite (enstatite = forsterite + silica-rich melt) could extend to pressures above 5 GPa in KCl-bearing systems, in contrast to the behavior in the KCl-free system.  相似文献   

16.
 We carried out a series of melting experiments with hydrous primitive mantle compositions to determine the stability of dense hydrous phases under high pressures. Phase relations in the CaO–MgO–Al2O3–SiO2 pyrolite with ˜2 wt% of water have been determined in the pressure range of 10–25 GPa and in the temperature range between 800 and 1400 °C. We have found that phase E coexisting with olivine is stable at 10–12 GPa and below 1050 °C. Phase E coexisting with wadsleyite is stable at 14–16 GPa and below 900 °C. A superhydrous phase B is stable in pyrolite below 1100 °C at 18.5 GPa and below 1300 °C at 25 GPa. No hydrous phases other than wadsleyite are stable in pyrolite at 14–17 GPa and 900–1100 °C, suggesting a gap in the stability of dense hydrous magnesium silicates (DHMS). We detected an expansion in the stability field of wadsleyite to lower pressures (12 GPa and 1000 °C). The H2O content of wadsleyite was found to decrease not only with increasing temperature but also with increasing pressure. The DHMS phases could exist in a pyrolitic composition only under the conditions present in the subducting slabs descending into the lower mantle. Under the normal mantle and hot plume conditions, wadsleyite and ringwoodite are the major H2O-bearing phases. The top of the transition zone could be enriched in H2O in accordance with the observed increase in water solubility in wadsleyite with decreasing pressure. As a consequence of the thermal equilibration between the subducting slabs and the ambient mantle, the uppermost lower mantle could be an important zone of dehydration, providing fluid for the rising plumes. Received: 9 September 2002 / Accepted: 11 January 2003 Acknowledgements The authors are thankful to Y. Ito for the assistance with the EPMA measurement, A. Suzuki, T. Kubo and T. Kondo for technical help with the high-pressure experiments and Raman and X-ray diffraction measurements and C.R. Menako for technical support. K. Litasov thanks H. Taniguchi for his continuous encouragement and the Center for Northeast Asian Studies of Tohoku University and the Japanese Society for the Promotion of Science for the research fellowships. This work was partially supported by the Grant-in-Aid of Scientific Research of the Priority Area (B) of the Ministry of Education, Science, Sport, and Culture of the Japanese government (no. 12126201) to E. Ohtani.  相似文献   

17.
The density of liquid Fe–S was measured at 4 GPa and 1,923 K using a sink/float method with a composite density marker. The density marker consisted of a Pt rod core and an Al2O3 tube surrounding. The uncertainty in the density of the composite marker is much smaller than that of the composite sphere, which had been used in previous density measurements. The density of liquid Fe–S decreases nonlinearly with increasing sulfur content at 4 GPa and 1,923 K. This tendency is consistent with the results measured at ambient pressure. The molar volume of FeS calculated from the measured density gradually increases with sulfur content. The excess molar volume from ideal mixing of Fe and S at 4 GPa was negative value. The new method proposed here is applicable to the density measurement of other Fe alloys at high pressure. The tendency of the molar volume and the excess molar volume with sulfur content at ambient pressure is consistent with these at high pressure at least up to 4 GPa. The excess molar volume at high pressure is essential for estimating the amount of light elements in the outer core.  相似文献   

18.
Piston cylinder experiments were performed to constrain the pressure and temperature conditions for two high-pressure antigorite dehydration reactions found in silica-enriched serpentinites from Cerro del Almirez (Nevado–Filábride Complex, Betic Cordillera, southern Spain). At 630–660°C and pressures greater than 1.6 GPa, antigorite first reacts with talc to form orthopyroxene ± chlorite + fluid. We show that orthopyroxene + antigorite is restricted to high-pressure metamorphism of silica-enriched serpentinite. This uncommon assemblage is helpful in constraining metamorphic conditions in cold subduction environments, where antigorite serpentinites have no diagnostic assemblages over a large pressure and temperature range. The second dehydration reaction leads to the breakdown of antigorite to olivine + orthopyroxene + chlorite + fluid. The maximum stability of antigorite is found at 680°C at 1.9 GPa, which also corresponds to the maximum pressure limit for tremolite coexisting with olivine + orthopyroxene. The high aluminium (3.70 wt% Al2O3) and chromium contents (0.59 wt% Cr2O3) of antigorite in the investigated starting material is responsible for the expansion of the serpentinite stability to 60–70°C higher temperatures at 1.8 GPa than the antigorite stability calculated in the Al-free system. The antigorite from our study has the highest Al–Cr contents among all experimental studies and therefore likely constraints the maximum stability of antigorite in natural systems. Comparison of experimental results with olivine–orthopyroxene–chlorite–tremolite assemblages outcropping in Cerro del Almirez indicates that peak metamorphic conditions were 680–710°C and 1.6–1.9 GPa.  相似文献   

19.
The solubility of water in coexisting enstatite and forsterite was investigated by simultaneously synthesizing the two phases in a series of high pressure and temperature piston cylinder experiments. Experiments were performed at 1.0 and 2.0 GPa at temperatures between 1,100 and 1,420°C. Integrated OH absorbances were determined using polarized infrared spectroscopy on orientated single crystals of each phase. Phase water contents were estimated using the calibration of Libowitzky and Rossman (Am Mineral 82:1111–1115, 1997). Enstatite crystals, synthesized in equilibrium with forsterite and an aqueous phase at 1,350°C and 2.0 GPa, contain 114 ppm H2O. This is reduced to 59 ppm at 1,100°C, under otherwise identical conditions, suggesting a strong temperature dependence. At 1,350°C and 1.0 GPa water solubility in enstatite is 89 ppm, significantly lower than that at 2.0 GPa. In contrast water solubility in forsterite is essentially constant, being in the range 36–41 ppm for all conditions studied. These data give partition coefficients in the range 2.28–3.31 for all experiments at 1,350°C and 1.34 for one experiment at 1,100°C. The incorporation of Al2O3 in enstatite modifies the OH stretching spectrum in a systematic way, and slightly increases the water solubility.  相似文献   

20.
A simplest equation within the framework of the Mie-Grüneisen–Einstein approach is considered. Pressure estimation values are presented that are derived by conventional arithmetic and algebraic calculations as a function of temperature and volume. The equation under consideration complies with the Mie-Grüneisen–Debye model at high temperature. Different versions of an equation of state (EoS) of MgO proposed by Speziale et al. (J Geophys Res 106B:515–528, 2001) as a pressure standard at high temperatures are subject to analyses. In the literature, at least four versions of Speziale et al. EoS of MgO are discussed; the discrepancy between them reaching a few GPa at T > 2,000 K and P > 100 GPa. Our analyses of these equations suggest that the volume dependence of the Debye temperature is accepted arbitrarily and does not agree with the definition of the Grüneisen parameter, γ = −(∂lnΘ/∂lnV) T . Pressure as a function of temperature and volume in the Mie-Grüneisen–Einstein approach or the Gao pressure calculator can be used to estimate true pressure at compression x = V/V 0 < 1 with the Speziale et al. EoS of MgO.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号