共查询到20条相似文献，搜索用时 27 毫秒
1.
地震断层作用下的埋地管道等效分析模型 总被引：2，自引：0，他引：2
地震作用下,活动断层附近的埋地管道易发生强度屈服、局部屈曲或整体失稳等形式的破坏,建立准确、高效的埋地管道在断层作用下的计算模型,对管道的抗震设计和震后安全状态评估具有重要的实用价值。本文采用非线性弹簧模拟远离断层处埋地管道的反应,基于管土之间小变形段管道处于强化阶段,提出一种改进的管土等效分析模型,进一步减小了管土之间大变形段的分析长度,从而提高了有限元分析效率。该模型采用ALA推荐的方法计算管土间的滑动摩擦力,可以考虑土体种类的影响;用Kennedy方法确定管道的计算长度。通过与精确模型比较,验证了管土等效模型的合理性和有效性。 相似文献
2.
The seismic response analysis of buried pipelines at fault crossings is a complex problem requiring nonlinear 3D soil-structure and large deformation analyses. Such analyses are computationally expensive and the results are hard to evaluate. Therefore, a simple numerical model is needed for engineering and design offices to determine the seismic demand of steel pipes at fault crossings. This paper presents a simplified numerical model for buried steel pipes crossing strike-slip faults and oriented perpendicular to the fault. Two pipes with different diameter to thickness (D/t) ratios and steel grades are used in the study. The proposed model permits plastic hinge formations in the pipe due to incrementally applied fault movements, allows determination of the critical length of the pipeline and measure strains developed on the tension and compression sides in the pipe. The model also considers the effect of bending as well as axial strains due to stretching. 相似文献
3.
海洋地震频繁且海底土体环境复杂,当地震导致断层土体发生永久变形后,穿越断层的海底埋地管道也将受迫发生变形。为确定变形后的管道能否正常工作,需根据实际工况对其进行应变响应预测。首先通过有限元计算软件ABAQUS建立管道与走滑断层的三维实体模型,模拟管-土间的接触作用并通过等效边界方法修正模型,得到管道局部屈曲破坏形式及应变分布情况。然后,通过调整有限元模型参数对断层交角、管道工作内压、管道径厚比对管道极限塑性应变的影响进行敏感性分析,定性分析不同敏感性因素对穿越走滑断层海底管道应变响应的影响。最后,在数值模拟数据的基础上通过MATLAB软件利用基于遗传算法优化的BP神经网络实现对管道应变响应的精确预测。结果表明:穿越走滑断层管道在发生局部屈曲时,可根据轴向压缩应变突变现象确定管道局部屈曲时对应的断层位移,并且断层交角、管道工作内压和管道径厚比都会对跨断层管道应变响应产生影响。 相似文献
4.
利用有限元软件ABAQUS,结合用户自定义Python程序,开展地震断层作用下深海管道局部变形和压溃过程的数值模拟。分析均质土体和随机分布土体模型的地震断层位移大小对管道局部变形的影响,并分析断层诱发的局部挤压变形对管道压溃压力的影响。研究表明:相比于断层走向与管道轴线方向垂直的走滑断层,断层走向与管道轴线方向夹角为45°的走滑断层作用下管道的压溃压力较小,且当断层走向为管道轴线方向逆时针旋转45°时,左旋走滑断层作用下管道的压溃压力低于右旋走滑断层作用下的管道压溃压力。断层位移相同时,管道径厚比越大,压溃压力越小。考虑土壤随机性时,由于APIX65钢制管道刚性较大,且管道两侧土体内聚力和摩擦角分散于均质土壤土体参数均值两侧,因此断层作用过程中管道受到的土压力在均质土壤模型中的土压力数值处上下波动。 相似文献
5.
Polynikis Vazouras Spyros A. Karamanos Panos Dakoulas 《Soil Dynamics and Earthquake Engineering》2010
The present paper investigates the mechanical behavior of buried steel pipelines, crossing an active strike-slip tectonic fault. The fault is normal to the pipeline direction and moves in the horizontal direction, causing stress and deformation in the pipeline. The interacting soil–pipeline system is modelled rigorously through finite elements, which account for large strains and displacements, nonlinear material behavior and special conditions of contact and friction on the soil–pipe interface. Considering steel pipelines of various diameter-to-thickness ratios, and typical steel material for pipeline applications (API 5L grades X65 and X80), the paper focuses on the effects of various soil and pipeline parameters on the structural response of the pipe, with particular emphasis on identifying pipeline failure (pipe wall wrinkling/local buckling or rupture). The effects of shear soil strength, soil stiffness, horizontal fault displacement, width of the fault slip zone are investigated. Furthermore, the influence of internal pressure on the structural response is examined. The results from the present investigation are aimed at determining the fault displacement at which the pipeline fails and can be used for pipeline design purposes. The results are presented in diagram form, which depicts the critical fault displacement, and the corresponding critical strain versus the pipe diameter-to-thickness ratio. A simplified analytical model is also developed to illustrate the counteracting effects of bending and axial stretching. The numerical results for the critical strain are also compared with the recent provisions of EN 1998-4 and ASCE MOP 119. 相似文献
6.
The present paper addresses the mechanical behavior of buried steel pipes crossing active strike-slip tectonic faults. The pipeline is assumed to cross the vertical fault plane at angles ranging between zero and 45 degrees. The fault moves in the horizontal direction, causing significant plastic deformation in the pipeline. The investigation is based on numerical simulation of the nonlinear response of the soil–pipeline system through finite elements, accounting for large strains and displacements, inelastic material behavior of the pipeline and the surrounding soil, as well as contact and friction on the soil–pipe interface. Steel pipes with D/t ratio and material grade typical for oil and gas pipelines are considered. The analysis is conducted through an incremental application of fault displacement. Appropriate performance criteria of the steel pipeline are defined and monitored throughout the analysis. The effects of various soil and line pipe parameters on the mechanical response of the pipeline are examined. The numerical results determine the fault displacement at which the specified performance criteria are reached, and are presented in diagram form, with respect to the crossing angle. The effects of internal pressure on pipeline performance are also investigated. In an attempt to explain the structural behavior of the pipeline with respect to local buckling, a simplified analytical model is also developed that illustrates the counteracting effects of pipeline bending and axial stretching for different crossing angles. The results from the present study can be used for the development of performance-based design methodologies for buried steel pipelines. 相似文献
7.
Tarek H. Abdoun Da Ha Michael J. O’Rourke Michael D. Symans Thomas D. O’Rourke Michael C. Palmer Harry E. Stewart 《Soil Dynamics and Earthquake Engineering》2009
Seismic ground faulting is a severe hazard for continuous buried pipelines. Over the years, researchers have attempted to understand pipe behavior, most frequently via numerical modeling and simulation. However, there has been little, if any, physical modeling and tests to verify the numerical modeling approaches and assumptions. This paper presents results of five pairs of centrifuge tests designed to investigate the influence of various factors on the behavior of buried high-density polyethylene (HDPE) pipelines subjected to strike-slip faulting. Parameters considered are the soil moisture content, fault offset rate, relative burial depth (H/D), and pipe diameter. The centrifuge test results show that pipe behavior, specifically pipe strain, is nominally not affected by the soil moisture content and fault offset rate when the pipe is subjected to strike-slip faulting. On the other hand, the burial depth ratio (H/D) and pipe diameter influence peak pipe strain, and in some cases, the ground soil failure pattern. 相似文献
8.
Shantanu Joshi Amit Prashant Arghya Deb Sudhir K. Jain 《Soil Dynamics and Earthquake Engineering》2011
Presently available simplified analytical methods and semi-empirical methods for the analysis of buried pipelines subjected to fault motion are suitable only for the strike-slip and the normal-slip type fault motions, and cannot be used for the reverse fault crossing case. A simple finite element model, which uses beam elements for the pipeline and discrete nonlinear springs for the soil, has been proposed to analyse buried pipeline subjected to reverse fault motion. The material nonlinearities associated with pipe-material and soil, and geometric nonlinearity associated with large deformations were incorporated in the analysis. Complex reverse fault motion was simulated using suitable constraints between pipe-nodes and ground ends of the soil spring. Results of the parametric study suggest that the pipeline's capacity to accommodate reverse fault offset can be increased significantly by choosing a near-parallel orientation in plan with respect to the fault line. Further improvement in the response of the pipeline is possible by adopting loose backfill, smooth and hard surface coating, and shallow burial depth in the fault crossing region. For normal or near normal orientations, pipeline is expected to fail due to beam buckling at very small fault offsets. 相似文献
9.
The performance of pipelines subjected to permanent strike–slip fault movement is investigated by combining detailed numerical simulations and closed-form solutions. First a closed-form solution for the force–displacement relationship of a buried pipeline subjected to tension is presented for pipelines of finite and infinite lengths. Subsequently the solution is used in the form of nonlinear springs at the two ends of the pipeline in a refined finite element model, allowing an efficient nonlinear analysis of the pipe–soil system at large strike–slip fault movements. The analysis accounts for large strains, inelastic material behavior of the pipeline and the surrounding soil, as well as contact and friction conditions on the soil–pipe interface. The numerical models consider infinite and finite length of the pipeline corresponding to various angles β between the pipeline axis and the normal to the fault plane. Using the proposed closed-form nonlinear force–displacement relationship for buried pipelines of finite and infinite length, axial strains are in excellent agreement with results obtained from detailed finite element models that employ beam elements and distributed springs along the pipeline length. Appropriate performance criteria of the steel pipeline are adopted and monitored throughout the analysis. It is shown that the end conditions of the pipeline have a significant influence on pipeline performance. For a strike–slip fault normal to the pipeline axis, local buckling occurs at relatively small fault displacements. As the angle between the fault normal and the pipeline axis increases, local buckling can be avoided due to longitudinal stretching, but the pipeline may fail due to excessive axial tensile strains or cross sectional flattening. Finally a simplified analytical model introduced elsewhere, is enhanced to account for end effects and illustrates the formation of local buckling for relative small values of crossing angle. 相似文献
10.
穿越逆冲断层的埋地管道非线性反应分析 总被引：2，自引：0，他引：2
穿越逆冲断层的埋地管道在地震作用下,容易发生局部屈曲或整体失稳等形式的破坏,研究逆冲断层作用下的埋地管道地震反应规律,对管道抗震设计及施工等具有重要的意义。本文将埋地管线及周围土体从半无限地球介质中取出,分别以空间薄壳单元和实体单元进行离散,采用非线性接触力学方法模拟管、土之间的滑移、分离及闭合现象;采用线性位移加载模拟断层的错动,考虑了系统初始应力状态的影响,对土体未开裂前的管土相互作用系统进行了拟静力数值分析;分析了位错量、土体刚度、埋设深度、径厚比及跨越角度对埋地管道反应的影响,得出了一些有益的结论。 相似文献
11.
The principal causes of earthquake-induced ground deformation are identified and their interaction with underground infrastructure, primarily pipelines and conduits, is described. The coupled forces normal and parallel to underground pipelines arising from earthquake-induced ground movement are evaluated, including a review of measured stresses on pipe surfaces during large-scale testing, evaluation of frictional forces related to soil-pipe interaction, and the resolution of interaction forces along and across pipelines. Methods for characterizing soil reaction to pipe lateral and vertical movements are presented. The maximum downward pipe force is only about one-third the maximum force determined with conventional bearing capacity equations, thus requiring changes in current analytical and design practice. The analytical results for pipeline response to strike-slip and normal fault rupture are shown to compare favorably with the results of both large-scale and centrifuge tests of soil-pipeline interaction simulating these types of severe ground deformation. 相似文献
12.
跨断层隔震管道管端与土体相互作用分析 总被引：1，自引：0，他引：1
断层错动是造成埋地管道破坏的重要因素之一,因此,跨断层埋地管道在断层错动下的破坏机制、模型设计与参数分析和管道抗断层措施一直是生命线工程的前沿问题。对跨断层管道内力分析取得的成果较多,比较经典的是Newm ark-Hall方法、Kennedy方法和王汝梁方法,后来又出现基于壳模型的有限元分析方法。现有的管道抗断层措施具有其优点的同时亦有其不足。本文基于壳模型的有限元动力数值模拟,对一种管道跨断层隔震措施进一步研究,考虑管端与土体相互作用计算隔震管段的断层错动响应。计算结果表明拉应变容易在土中的管段传递,相比较而言,压应变不容易在土中的管段传递;最大拉应变降低比较多,最大压应变降低比较少。根据分析结果,对跨断层隔震管段边界条件的选取提出建议。 相似文献
13.
基于ABAQUS软件平台,建立穿越断层的管道、有压液体及周围土体的三维有限元模型,分别在静力荷载作用和地震作用下,对不同运动形式断层（走滑断层、正断层、逆断层）中的管道进行模拟,并对管道内有无有压液体进行对比分析。分别得到管道在静力荷载作用下和地震作用下空管道与有压管道的变形特征,将其进行对比分析,得到管道内液体的质量和压力在静力荷载作用及地震荷载作用下对管道的不同影响。结果表明：在静力荷载作用下管道内液体的质量和压力提高了管道的抗变形能力,使管道更安全;而在地震作用下管道内液体的质量和压力削弱了管道的抗变形能力,使管道更容易被破坏。 相似文献
14.
Dimitrios K. Karamitros George D. Bouckovalas George P. Kouretzis 《Soil Dynamics and Earthquake Engineering》2007,27(3):200-211
Existing analytical methods for the stress analysis of buried steel pipelines at crossings with active strike-slip faults depend on a number of simplifications, which limit their applicability and may even lead to non-conservative results. The analytical methodology presented herein maintains the well-established assumptions of existing methodologies, but also introduces a number of refinements in order to achieve a more wide range of application without any major simplicity sacrifice. More specifically, it employs equations of equilibrium and compatibility of displacements to derive the axial force applied on the pipeline and adopts a combination of beam-on-elastic-foundation and elastic-beam theory to calculate the developing bending moment. Although indirectly, material and large-displacement non-linearities are also taken into account, while the actual distribution of stresses on the pipeline cross-section is considered for the calculation of the maximum design strain. The proposed methodology is evaluated against the results of a series of benchmark 3D non-linear analyses with the finite element method. It is shown that fairly accurate predictions of pipeline strains may be obtained for a wide range of crossing angles and fault movement magnitudes encountered in practice. 相似文献
15.
跨越断层埋地管线地震反应数值分析 总被引：9，自引：2，他引：7
跨越断层埋地管线在地震中的破坏是非常严重的,地震本身和管土相互作用体系中都存在很多不确定性因素,所以管线在断层运动过程中反应比较复杂。本文利用有限元理论和数值模拟手段,建立了管土作用模型,采用非线性接触问题研究方法详细地分析了管线由断层运动而产生的反应,对影响管线的各种因素进行了分析,包括位错量、跨越角度、断层运动形式、埋设深度、初始轴向力、断层裂缝宽度、填覆土质和管径。通过研究,得到一些初步结论。 相似文献
16.
沉陷区域埋地管线数值模拟分析 总被引：4，自引：0，他引：4
场地的不均匀沉陷是导致埋地管线破坏的重要原因之一。本文考虑了材料非线性、几何非线性以及管土接触非线性,将管线计算分析模型模拟为四节点薄壳单元结构,周围填覆土体采用八节点六面体单元划分。管土相互作用模拟为三维刚性与柔性的面面接触单元结构,并采用线性位移加载来模拟土体的沉陷作用,对三维薄壳有限元模型进行数值计算分析。通过比较不同参数,如沉陷长度、沉陷深度、埋深、管径、径厚比、土特性等对管线的反应影响,得出管线在沉陷情况下的应力和应变的关系,通过算例分析,说明了该方法能更好地模拟管线的破坏过程,该方法将为沉陷区域埋地管线数值模拟提供理论分析依据。 相似文献
17.
Mohammad Hossein Erami Masakatsu Miyajima Shogo Kaneko Toshio Toshima Shozo Kishi 《地震工程与结构动力学》2015,44(3):403-417
This paper describes an investigation of pipe–soil interaction equations suggested by currently used pipeline seismic design codes and the applicability of these equations to segmented pipelines. The results of computer‐aided analyses were compared to results obtained in full‐scale experiments on a segmented ductile iron pipeline 93 mm in diameter and 15 m in length. The pipeline was installed 600 mm below the ground surface in a sandy soil compacted to two different subgrade reaction values. The type of fault considered was a reverse fault with an intersection angle of 60° with the pipeline, and the fault movement was a total of 350 mm in three same steps in the fault trace direction. The findings of this study demonstrate the necessity of considering the nature of soil behavior in pipe–soil interaction equations and the effects of connection joints on the integrated response of pipelines to fault‐induced ground deformations. A new combination of equations constituting a direction‐wise selection from among the equations proposed by currently used guidelines is introduced as a new series to describe pipe–soil interaction for segmented pipelines and is verified using the results of full‐scale experiments. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
18.
Probabilistic permanent fault displacement hazard via Monte Carlo simulation and its consideration for the probabilistic risk assessment of buried continuous steel pipelines 
下载免费PDF全文
下载免费PDF全文 Permanent fault displacements (PFDs) because of fault ruptures emerging at the surface are critical for seismic design and risk assessment of continuous pipelines. They impose significant compressive and tensile strains to the pipe cross‐section at pipe‐fault crossings. The complexity of fault rupture, inaccurate mapping of fault location and uncertainties in fault‐pipe crossing geometries require probabilistic approaches for assessing the PFD hazard and mitigating pipeline failure risk against PFD. However, the probabilistic approaches are currently waived in seismic design of pipelines. Bearing on these facts, this paper first assesses the probabilistic PFD hazard by using Monte Carlo‐based stochastic simulations whose theory and implementation are given in detail. The computed hazard is then used in the probabilistic risk assessment approach to calculate the failure probability of continuous pipelines under different PFD levels as well as pipe cross‐section properties. Our probabilistic pipeline risk computations consider uncertainties arising from complex fault rupture and geomorphology that result in inaccurate mapping of fault location and fault‐pipe crossings. The results presented in this paper suggest the re‐evaluation of design provisions in current pipeline design guidelines to reduce the seismic risk of these geographically distributed structural systems. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
19.
In the present paper a semi-analytical methodology for a nonlinear stress–strain analysis of buried steel pipelines at active fault crossings is presented and verified. The developed model introduces a number of critical refinements to the existing methodologies which extend the application area of analytical models in pipeline design. In particular, a strike-slip and normal-slip fault crossings can be analyzed taking into account material and large displacement nonlinearities, nonlinear pipe–soil interaction. The proposed model is verified against the results by other authors and numerical results, obtained with the finite element method. 相似文献
20.
Seismic ground faulting is the greatest hazard for continuous buried pipelines.Over the years,researchers have attempted to understand pipeline behavior mostly via numerical modeling such as the finite element method.The lack of well-documented field case histories of pipeline failure from seismic ground faulting and the cost and complicated facilities needed for full-scale experimental simulation mean that a centrifuge-based method to determine the behavior of pipelines subjected to faulting is best to verify numerical approaches.This paper presents results from three centrifuge tests designed to investigate continuous buried steel pipeline behavior subjected to normal faulting.The experimental setup and procedure are described and the recorded axial and bending strains induced in a pipeline are presented and compared to those obtained via analytical methods.The influence of factors such as faulting offset,burial depth and pipe diameter on the axial and bending strains of pipes and on ground soil failure and pipeline deformation patterns are also investigated.Finally,the tensile rupture of a pipeline due to normal faulting is investigated. 相似文献