共查询到20条相似文献，搜索用时 187 毫秒
1.
利用有限元软件ABAQUS,结合用户自定义Python程序,开展地震断层作用下深海管道局部变形和压溃过程的数值模拟。分析均质土体和随机分布土体模型的地震断层位移大小对管道局部变形的影响,并分析断层诱发的局部挤压变形对管道压溃压力的影响。研究表明:相比于断层走向与管道轴线方向垂直的走滑断层,断层走向与管道轴线方向夹角为45°的走滑断层作用下管道的压溃压力较小,且当断层走向为管道轴线方向逆时针旋转45°时,左旋走滑断层作用下管道的压溃压力低于右旋走滑断层作用下的管道压溃压力。断层位移相同时,管道径厚比越大,压溃压力越小。考虑土壤随机性时,由于APIX65钢制管道刚性较大,且管道两侧土体内聚力和摩擦角分散于均质土壤土体参数均值两侧,因此断层作用过程中管道受到的土压力在均质土壤模型中的土压力数值处上下波动。 相似文献
2.
海洋地震频繁且海底土体环境复杂,当地震导致断层土体发生永久变形后,穿越断层的海底埋地管道也将受迫发生变形。为确定变形后的管道能否正常工作,需根据实际工况对其进行应变响应预测。首先通过有限元计算软件ABAQUS建立管道与走滑断层的三维实体模型,模拟管-土间的接触作用并通过等效边界方法修正模型,得到管道局部屈曲破坏形式及应变分布情况。然后,通过调整有限元模型参数对断层交角、管道工作内压、管道径厚比对管道极限塑性应变的影响进行敏感性分析,定性分析不同敏感性因素对穿越走滑断层海底管道应变响应的影响。最后,在数值模拟数据的基础上通过MATLAB软件利用基于遗传算法优化的BP神经网络实现对管道应变响应的精确预测。结果表明:穿越走滑断层管道在发生局部屈曲时,可根据轴向压缩应变突变现象确定管道局部屈曲时对应的断层位移,并且断层交角、管道工作内压和管道径厚比都会对跨断层管道应变响应产生影响。 相似文献
3.
分析钢筋混凝土(RC)梁与柱基于不同地震作用下的变形限值,对钢筋混凝土梁与柱进行低周往复循环加载拟静力试验。然后对试验进行仿真模拟,将试验结果与仿真模拟结果进行对比分析,发现二者结果相近,从而验证仿真模拟的可行性。在构件的荷载-位移曲线上获取屈服点、峰值点和极限点,分别计算这3个状态点对应的侧向位移值与构件计算长度的比值,则可得出构件在小震、中震和大震时对应的位移角值。改变梁、柱构件的剪跨比、配筋形式以及柱构件的轴压比等,来得到更多构件的荷载-位移曲线,将所有结果进行统计分析,得到钢筋混凝土构件在不同地震作用下的位移角限值。 相似文献
4.
5.
编制完全耦合的三维排水有效应力动力反应分析程序，对可液化地基进行三维地震响应分析，探讨了不同土性参数、不同土层构成和不同附加压重等因素对可液化地基抗液化性能的影响。结果表明：在地震荷载作用下，天然饱和砂土地基中的超孔隙水压力随深度的增大而增大；在不同深度处，超孔压峰值到达的时刻比地震加速度峰值到达的时刻要晚；随输入地震加速度的减弱，深层处的超孔压开始消散或基本保持不变，浅层处的超孔压保持不变或略有上升，这一现象与土性参数、输入地震荷载的情况等因素有关；土性参数对土体本身的抗液化性能有重要影响，初始孔隙比越小，相对密度越大，土体的抗液化能力越强；附加压重有利于地基抗液化能力的提高；随着附加压重的增大，超孔压比减小；附加压重对地基中超孔隙水压力的增长有明显的抑制作用。 相似文献
6.
PCCP（预应力钢筒混凝土管）因其优良性能被广泛应用于我国水利水电及市政给排水等生命线工程的建设中。现有研究多为静力分析,少有学者对PCCP管内流体的动力相互作用开展研究。本文利用ABAQUS对PCCP结构及其管内流体在地震荷载下的双向流固耦合作用进行分析,开展了考虑流固耦合与未耦合条件下管道各个结构层的动力响应。进一步计算了考虑内水压力、地震荷载大小和管内水流速度等条件变化对管道受力变形特性的影响。结果表明:流固耦合模型能更加真实地还原和模拟在役PCCP的工作状态;内水压力显著影响管道的受力状态,PCCP结构随着输水压力的增大逐步由受压状态向受拉过渡,且受拉区域和拉应力峰值逐渐增大;管内水流速对应力场影响很微弱。 相似文献
7.
近断层地震作用下基础隔震层组合限位振动台实验研究 总被引：1，自引：0，他引：1
近断层脉冲型地震作用下,基础隔震结构隔震层会产生过大变形,导致隔震支座侧倾失稳,隔震体系破坏。设计制作了3层基础隔震钢框架实验模型和11种U型钢板I型铅棒组合限位器,进行了U型钢板静力加载实验和近断层脉冲型地震作用下基础隔震层软碰撞限位振动台模型实验。实验表明：①静力加载时,U型钢板具有很好的弹性性能;②动力作用下,组合限位器残余变形较小,仍具有良好限位复位能力;③近断层地震作用下,基础隔震层软限位效果良好,同时控制上部结构层间变形在允许范围内。 相似文献
8.
9.
埋地管道地震作用下的破坏因素源于地震引起的永久地面变形(PGD),其中管道-土体间相互作用决定土体位移作用到管体的大小。利用离心机试验技术模拟埋地管道在逆断层大位移下的反应特性,重点讨论断层与管道的交角、断层位移大小、管土相互作用、管径和埋深五个参数对管道破坏的影响水平。实验结果表明:上述参数对管道断层作用的反应均有明显影响,其中断层的位移量、管土相互作用、埋深和管径的影响更为显著。本文的研究结果对于管道经过断层区的抗震设计有十分重要的意义。 相似文献
10.
鉴于穿越地震活动带逆断层的铁路山岭隧道易受逆断层滑动的影响,且目前铁路隧道穿越多条活动性断层可供借鉴经验较少的现状。文章采用数值分析方法,对活动逆断层错动下的铰链式衬砌隧道在地震荷载作用下围岩加固方式、超挖设计结构的动力响应进行对比分析。结果表明逆断层错动时,对浅部地层变形的影响范围大于深部,但最大附加变形出现在深部断层面附近,且错距越大其最大附加变形值越大,断层活动对隧道结构安全影响较为显著。注浆加固并不改变衬砌在地震中的震动频谱特性,宜采用施作单层衬砌预留修复空间的设计方案。对于是否超挖设计的两种工况下,衬砌位移变化规律一致,衬砌的震动频谱特性一致。经过监控量测发现支护压应力在埋设2个月左右后趋于稳定。所得结论可为今后类似工程结构设计与施工提供参考。 相似文献
11.
地震断层作用下的埋地管道等效分析模型 总被引：2，自引：0，他引：2
地震作用下,活动断层附近的埋地管道易发生强度屈服、局部屈曲或整体失稳等形式的破坏,建立准确、高效的埋地管道在断层作用下的计算模型,对管道的抗震设计和震后安全状态评估具有重要的实用价值。本文采用非线性弹簧模拟远离断层处埋地管道的反应,基于管土之间小变形段管道处于强化阶段,提出一种改进的管土等效分析模型,进一步减小了管土之间大变形段的分析长度,从而提高了有限元分析效率。该模型采用ALA推荐的方法计算管土间的滑动摩擦力,可以考虑土体种类的影响;用Kennedy方法确定管道的计算长度。通过与精确模型比较,验证了管土等效模型的合理性和有效性。 相似文献
12.
跨越断层埋地管线地震反应数值分析 总被引：7，自引：2，他引：7
跨越断层埋地管线在地震中的破坏是非常严重的,地震本身和管土相互作用体系中都存在很多不确定性因素,所以管线在断层运动过程中反应比较复杂。本文利用有限元理论和数值模拟手段,建立了管土作用模型,采用非线性接触问题研究方法详细地分析了管线由断层运动而产生的反应,对影响管线的各种因素进行了分析,包括位错量、跨越角度、断层运动形式、埋设深度、初始轴向力、断层裂缝宽度、填覆土质和管径。通过研究,得到一些初步结论。 相似文献
13.
Probabilistic permanent fault displacement hazard via Monte Carlo simulation and its consideration for the probabilistic risk assessment of buried continuous steel pipelines 
下载免费PDF全文
下载免费PDF全文 Permanent fault displacements (PFDs) because of fault ruptures emerging at the surface are critical for seismic design and risk assessment of continuous pipelines. They impose significant compressive and tensile strains to the pipe cross‐section at pipe‐fault crossings. The complexity of fault rupture, inaccurate mapping of fault location and uncertainties in fault‐pipe crossing geometries require probabilistic approaches for assessing the PFD hazard and mitigating pipeline failure risk against PFD. However, the probabilistic approaches are currently waived in seismic design of pipelines. Bearing on these facts, this paper first assesses the probabilistic PFD hazard by using Monte Carlo‐based stochastic simulations whose theory and implementation are given in detail. The computed hazard is then used in the probabilistic risk assessment approach to calculate the failure probability of continuous pipelines under different PFD levels as well as pipe cross‐section properties. Our probabilistic pipeline risk computations consider uncertainties arising from complex fault rupture and geomorphology that result in inaccurate mapping of fault location and fault‐pipe crossings. The results presented in this paper suggest the re‐evaluation of design provisions in current pipeline design guidelines to reduce the seismic risk of these geographically distributed structural systems. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
14.
Flexible pipelines are often used to connect hard pipes from a foundation to a superstructure to accommodate large deformation in the base isolation layer during an earthquake. Although Chinese seismic design guidelines suggest several configurations, they are different from the designs that have been proven in practice, e.g., Japanese styles, and extensive experimental investigation into their seismic performance is required. Three types of seals, rubber-, metal- and asbestine-based, were tested quasi-statically with infilled pressurized water at 2.5 MPa. The asbestine-based seal leaked at a smaller deformation than the other two types of seals. Based on the test results, three damage states were defined and the deformation capacity was estimated. To evaluate their performance, a three-dimensional model of a base-isolated medical building was developed using OpenSees, with the flexible pipelines simulated by a mechanical model calibrated from the experimental data. A probabilistic seismic demand model and the fragility function of the flexible pipelines were then developed to evaluate the seismic performance.
相似文献15.
Mohammad Hossein Erami Masakatsu Miyajima Shogo Kaneko Toshio Toshima Shozo Kishi 《地震工程与结构动力学》2015,44(3):403-417
This paper describes an investigation of pipe–soil interaction equations suggested by currently used pipeline seismic design codes and the applicability of these equations to segmented pipelines. The results of computer‐aided analyses were compared to results obtained in full‐scale experiments on a segmented ductile iron pipeline 93 mm in diameter and 15 m in length. The pipeline was installed 600 mm below the ground surface in a sandy soil compacted to two different subgrade reaction values. The type of fault considered was a reverse fault with an intersection angle of 60° with the pipeline, and the fault movement was a total of 350 mm in three same steps in the fault trace direction. The findings of this study demonstrate the necessity of considering the nature of soil behavior in pipe–soil interaction equations and the effects of connection joints on the integrated response of pipelines to fault‐induced ground deformations. A new combination of equations constituting a direction‐wise selection from among the equations proposed by currently used guidelines is introduced as a new series to describe pipe–soil interaction for segmented pipelines and is verified using the results of full‐scale experiments. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
16.
Permanent earthquake‐induced actions in buried pipelines: Numerical modeling and experimental verification 下载免费PDF全文
下载免费PDF全文 《地震工程与结构动力学》2018,47(4):966-987
Buried pipelines are often constructed in seismic and other geohazard areas, where severe ground deformations may induce severe strains in the pipeline. Calculation of those strains is essential for assessing pipeline integrity, and therefore, the development of efficient models accounting for soil‐pipe interaction is required. The present paper is aiming at developing efficient tools for calculating ground‐induced deformation on buried pipelines, often triggered by earthquake action, in the form of fault rupture, liquefaction‐induced lateral spreading, soil subsidence, or landslide. Soil‐pipe interaction is investigated by using advanced numerical tools, which employ solid elements for the soil, shell elements for the pipe, and account for soil‐pipe interaction, supported by large‐scale experiments. Soil‐pipe interaction in axial and transverse directions is evaluated first, using results from special‐purpose experiments and finite element simulations. The comparison between experimental and numerical results offers valuable information on key material parameters, necessary for accurate simulation of soil‐pipe interaction. Furthermore, reference is made to relevant provisions of design recommendations. Using the finite element models, calibrated from these experiments, pipeline performance at seismic‐fault crossings is analyzed, emphasizing on soil‐pipe interaction effects in the axial direction. The second part refers to full‐scale experiments, performed on a unique testing device. These experiments are modeled with the finite element tools to verify their efficiency in simulating soil‐pipe response under landslide or strike‐slip fault movement. The large‐scale experimental results compare very well with the numerical predictions, verifying the capability of the finite element models for accurate prediction of pipeline response under permanent earthquake‐induced ground deformations. 相似文献
17.
输气管道作为1种薄壁壳体结构,逆冲断层引起的管道压缩变形容易使其破坏。本文以大北南疆输气管道工程为例,探讨了穿越克孜尔逆冲断层的输气管道地震安全问题。在确定管道穿越处的断层倾角、设防断层位错量、表征管土相互作用的土弹簧参数以及钢管容许应变等参数后,采用壳有限元方法,分析了穿越克孜尔逆冲断层的输气管道变形反应。分析结果显示,管道在逆冲断层作用下以压缩应变为主,管道内的最大轴向压缩应变的幅值随着交角的减小而减小。在通过探槽等方法确定断层活动位置后,该管道若以小于或等于11°的交角通过克孜尔断裂,断层引起的最大轴向压缩应变和拉伸应变均在管道相应的容许应变范围内,满足相关规范的抗震要求。 相似文献
18.
Abstract The seismic slip that occurred during the 1999 Chi-Chi earthquake in Taiwan showed contrastive behaviors in different regions along the Chelungpu Fault: A large and smooth slip occurred in the north, while a relatively small slip associated with high-frequency seismic wave radiation occurred in the south. The core samples from shallow boreholes at northern (Fengyuan) and southern (Nantou) sites penetrating the seismic Chelungpu Fault were analyzed. The fault zones at the northern site are characterized by soft clayey material associated with clayey injection veins. This suggests that the fault zones were pressurized during ancient seismic slip events, and hence the elastohydrodynamic lubrication occurred effectively. In contrast, the fault rock from the southern site is old pseudotachylyte that has been shattered by repeated ancient seismic slip events. Statistical analysis of many pseudotachylyte fragments reveals that the degree of frictional melting tended to be low. In this case, the seismic slip is restrained by the mechanical barrier of a highly viscous melt layer. These contrastive fault rocks were produced by repeated ancient seismic slip events, but the two corresponding mechanisms of friction are likely to have also occurred during the 1999 Chi-Chi earthquake, thus causing the contrastive slip behaviors in the north and south. 相似文献
19.
The seismic response analysis of buried pipelines at fault crossings is a complex problem requiring nonlinear 3D soil-structure and large deformation analyses. Such analyses are computationally expensive and the results are hard to evaluate. Therefore, a simple numerical model is needed for engineering and design offices to determine the seismic demand of steel pipes at fault crossings. This paper presents a simplified numerical model for buried steel pipes crossing strike-slip faults and oriented perpendicular to the fault. Two pipes with different diameter to thickness (D/t) ratios and steel grades are used in the study. The proposed model permits plastic hinge formations in the pipe due to incrementally applied fault movements, allows determination of the critical length of the pipeline and measure strains developed on the tension and compression sides in the pipe. The model also considers the effect of bending as well as axial strains due to stretching. 相似文献
20.
为研究埋地管道在地震激励时管-土相互作用的动力响应问题,研发双向层状剪切连续体模型土箱,建立管G土相互作用有限元分析模型,对横向非一致地震激励下埋地管道地震响应进行数值模拟分析,并与试验结果进行对比.结果表明:数值模拟和振动台试验结果中的管道应变峰值均呈现出沿管道中间大两端小的现象,管道中间应变峰值最小达到两端的1．6倍左右;管道加速度、 土体加速度峰值均随着加载等级的提高而增大,涨幅愈加明显,多峰频率由0~10Hz逐渐向10~ 20Hz频域扩散,管道运动更为自由;土体位移随着加载等级的提高呈现逐级增大的现象,在加载等级增加到0．4g 时位移曲线斜率减小,土体非线性表现明显.数值模拟和振动台试验对比分析的结论表明数值模拟分析的合理性和试验结果的可靠性,为研究横向非一致激励对埋地管道地震响应的影响提供了依据. 相似文献