共查询到20条相似文献，搜索用时 437 毫秒
1.
Vertical plate anchors provide an economical solution to safely resist the large horizontal forces experienced by the foundation of different structures such as bulkheads, sheet piles, retaining walls and so forth. This paper develops a multivariate adaptive regression spline (MARS) model-based approach for the determination of horizontal pullout capacity (P u ) of vertical plate anchors buried in cohesionless soil by utilizing experimental results reported by different researchers. Based on the collection of forty different pullout experimental test results reported in the literature for anchors buried in loose to dense cohesionless soil with an embedment ratio ranges from 1 to 5, a predictive approach for P u of vertical plate anchors has been developed in terms of non-dimensional pullout coefficient (M γq ). The capability of the proposed MARS model for estimating the values of M γq is examined by comparing the results obtained in the present study with those methods available in the literature. Using different statistical error measure criteria, this study indicates that the present approach is efficient in estimating the horizontal pullout capacity of vertical plate anchors as compared to other methods. The sensitivity analysis indicates that the embedment ratio (H/h, where H = embedment depth of anchor, and h = height of anchor) and internal friction angle (?) of soil mass are the two most important parameters for the evaluation of non-dimensional pullout coefficient (M γq ) using the proposed MARS model. 相似文献
2.
Plate anchors, such as suction embedded plate anchors and vertically driven plate anchors, offer economically attractive anchoring solutions for deep/ultra-deep water offshore developments. The rotation/keying processes of plate anchors will cause embedment losses, which lead to decreases of the uplift resistances of the anchors in normally consolidated soil. In the present paper, the keying processes of vertically installed strip and square plate anchors are simulated using the 3-D large deformation finite element method. The effects of loading eccentricity and pullout angle on the embedment loss during keying are investigated. Both the development of the uplift resistance and the soil flow mechanisms are presented. The numerical results show that the loading eccentricity e/B has a much larger effect on the embedment loss than the pullout angle does. The anchor shape has a minimal effect on the loss in anchor embedment. The shape factors (square/strip) are 1.05–1.09 for loss of embedment and 1.10–1.19 for capacity. 相似文献
3.
Ahmed M. Fahmy John R. de Bruyn T. A. Newson 《Geotechnical and Geological Engineering》2013,31(5):1525-1542
Two-dimensional plane strain finite element analysis has been used to simulate the inclined pullout behavior of strip anchors embedded in cohesive soil. Previous studies by other researchers were mainly concerned with plate anchors subjected to loads perpendicular to their longest axis and applied through the centre of mass. This paper investigates the behavior of vertical anchors subjected to pullout forces applied at various inclinations with respect to the longest anchor axis, and applied at the anchor top and through the centre of mass. The effects on the pullout behavior of embedment depth, overburden pressure, soil–anchor interface strength, anchor thickness, rate of clay strength increase, anchor inclination, load inclination and soil disturbance due to anchor installation were all studied. Anchor capacity is shown to increase with load inclination angle for anchors loaded through the centre of mass; greater effects are found for higher embedments. The results also show that anchor capacity improves at a decreasing rate with higher rates of increase of soil shear strength with depth. In addition, the capacity of vertically loaded anchors is shown to approximately double when the soil–anchor interface condition changes from fully separated to fully bonded. Similarly, disturbed clay strengths adjacent to the anchor following installation cause a significant reduction in anchor capacity. The results showed a significant effect of the point of load application for anchors inclined and normally loaded. The effects of other parameters, such as anchor thickness, were found to be less significant. 相似文献
4.
当结构在土体中运动时,往往导致土体发生较大的变形,此类问题采用大变形数值分析方法更为恰当。耦合欧拉-拉格朗日（Coupled Eulerian-Lagrangian, 简称CEL）法是大变形数值分析方法中的一种,在分析大变形问题时具有很强的适用性,但在国内尚未开展CEL法分析锚板承载力的研究。以方形锚板在均质土及线性土中的拔出试验为原型,基于CEL法建立数值模型,对锚板的极限承载力及破坏机制进行研究,并通过用户自定义子程序,实现了线性土的强度分布随锚板拔出而变化。计算结果表明,土体杨氏模量越大,锚板的极限承载力越大;随着位移增大,锚板的抗拔力先增大,后降低;当埋深小于临界埋深时,土体发生整体破坏;当埋深大于等于临界埋深时,土体发生局部破坏。数值计算反映的规律与试验结果基本吻合,体现了CEL法模拟锚板在海床中大位移响应的出色能力。 相似文献
5.
The ultimate uplift resistance of a group of multiple strip anchors placed in sand and subjected to equal magnitudes of vertical
upward pullout loads has been determined by means of model experiments. Instead of using a number of anchor plates in the
experiments, a single anchor plate was used by simulating the boundary conditions along the planes of symmetry on both the
sides of the anchor plate. The effect of clear spacing (s) between the anchors, for different combinations of embedment ratio (λ) of anchors and friction angle (ϕ) of soil mass, was examined in detail. The results were presented in terms of a non-dimensional efficiency factor (ξγ), which was defined as the ratio of the failure load for an intervening strip anchor of a given width (B) to that of a single strip anchor plate having the same width. It was clearly noted that the magnitude of ξγ reduces quite extensively with a decrease in the spacing between the anchors. The magnitude of ξγ for a given s/B was found to vary only marginally with respect to changes in λ and ϕ. The experimental results presented in this study compare reasonably well with the theoretical and experimental data available
in literature. 相似文献
6.
Three-dimensional numerical and analytical study of horizontal group of square anchor plates in sand
Hicham Mokhbi Mekki Mellas Abdelhak Mabrouki Jean-Michel Pereira 《Acta Geotechnica》2018,13(1):159-174
In this paper, numerical and analytical methods are used to evaluate the ultimate pullout capacity of a group of square anchor plates in row or square configurations, installed horizontally in dense sand. The elasto-plastic numerical study of square anchor plates is carried out using three-dimensional finite element analysis. The soil is modeled by an elasto-plastic model with a Mohr–Coulomb yield criterion. An analytical method based on a simplified three-dimensional failure mechanism is developed in this study. The interference effect is evaluated by group efficiency η, defined as the ratio of the ultimate pullout capacity of group of N anchor plates to that of a single isolated plate multiplied by number of plates. The variation of the group efficiency η was computed with respect to change in the spacing between plates. Results of the analyses show that the spacing between the plates, the internal friction angle of soil and the installation depth are the most important parameters influencing the group efficiency. New equations are developed in this study to evaluate the group efficiency of square anchor plates embedded horizontally in sand at shallow depth (H = 4B). The results obtained by numerical and analytical solutions are in excellent agreement. 相似文献
7.
By using the lower bound finite elements limit analysis, the pullout capacity of an inclined strip anchor plate embedded in a cohesionless soil medium has been computed with an inclusion of pseudo-static horizontal earthquake body forces. The variation of the pullout capacity factor (F γ ) with changes in horizontal earthquake acceleration co-efficient (α h ) has been computed by varying the inclination angle (β) of the anchor plate between 0° and 90°. The results clearly reveal that the pullout capacity factor (F γ ) decreases significantly with an increase in the value of α h . The reduction in the pullout resistance due to seismic forces (1) becomes much more extensive for a vertical anchor plate as compared to the horizontal anchor, (2) decreases generally with increases in the soil friction angle (?) and (3) increases with an increase in friction angle between soil and anchor plate (δ). The developments of the failure zone around the anchor plate were also examined by varying α h and β. The results obtained from the analysis compare well with the solutions reported in literature. 相似文献
8.
均质黏土中圆形平板锚的抗拉承载力分析 总被引：2，自引：1，他引：1
基于网格重新生成和场变量映射的大变形有限元模型,探索了立即脱离和无脱离两种典型条件下均质黏土中圆形平板锚的抗拉承载力。与小变形有限元比较,大变形分析克服了锚周围土体初始网格畸变的不利影响,能够追踪平板锚整个拔出过程中抗拉力的变化。通过具体算例,考察平板锚表面摩擦性质和上覆土重等因素对立即脱离工况承载力的影响程度,指出有重土中深锚的承载力小于无重土中对应的承载力与上覆土重之和,其上限是无脱离条件下的承载力。计算结果表明：土重对无脱离条件下的承载力影响很小,进而给出了无脱离承载力系数与初始埋深的关系曲线。 相似文献
9.
Priyanka Ghosh 《Computers and Geotechnics》2009,36(1-2):342-351
This paper presents the pseudo-dynamic analysis to determine the seismic vertical uplift capacity of a horizontal strip anchor using upper bound limit analysis. However, in the literature, the pseudo-static approach was used by few researchers to compute the seismic vertical pullout resistance, where the real dynamic nature of earthquake accelerations cannot be considered. Under the seismic conditions, the values of the unit weight component of uplift factor fγE are determined for different magnitudes of soil friction angle, soil amplification, embedment ratio and seismic acceleration coefficients both in the horizontal and vertical directions. It is observed that the uplift factor fγE decreases significantly with the increase in seismic accelerations and amplification but increases with the increase in embedment ratio. The results are compared with the existing values in the literature and the significance of the present methodology for designing the horizontal strip anchor is discussed. In presence of vertical earthquake acceleration and amplification of vibration, the present values of fγE compare reasonably well with the existing pseudo-static values obtained by modifying the horizontal acceleration coefficient. 相似文献
10.
The horizontal pullout capacity of a group of two rigid strip plate anchors embedded along the same vertical plane in clays, under undrained condition, has been determined. An increase of cohesion with depth has also been incorporated. The analysis has been performed by using an upper bound finite element limit analysis in combination with linear optimization. For different clear spacing (S) between the anchors, the efficiency factor (ηcγ) has been determined to evaluate the group failure load for different values of (1) embedment ratio (H/B), (2) the normalized rate (m) which accounts for a linear increase of cohesion with depth, and (3) normalized unit weight (γH/co). The magnitude of the group failure load (1) becomes maximum corresponding to a certain spacing (Scr) between the anchors, and (2) increases with an increase in the γH/co up to a certain value before attaining a certain maximum magnitude. The value of Scr/B has been found to vary generally between 0.7 and 1.2. The maximum magnitude of ηcγ, associated with the critical spacing, (1) increases generally with increases in H/B, and (2) decreases with an increase in m. For a greater spacing between the anchors, the analysis reveals the development of a local shear zone around the lower anchor plate. The numerical results developed are expected to be useful for purpose of design. 相似文献
11.
In the present analysis, an attempt is made to explore the seismic response of two nearby horizontal strip anchors embedded in non-homogenous c-? soil deposit at different depths. The analysis is performed by using two-dimensional finite-element software PLAXIS 2D. Each anchor carries equal static safe-working load without violating the ultimate uplift capacity under static condition. The soil is assumed to obey the Mohr?CCoulomb failure criterion. The behavior of single isolated anchor subjected to an earthquake loading is determined first to study the interference effect between two anchors. The horizontal acceleration response obtained from the Loma Prieta Gilroy Earthquake (1989) is considered as the input excitation in the analysis. A parametric study is performed by varying the clear spacing (S) between the anchors at different embedment ratios (??). The magnitude of vertical displacement, shear stress, and shear strain developed at different locations of the failure domain is determined for different clear spacings between the anchors. 相似文献
12.
砂土中扩体锚杆承载特性模型试验研究 总被引：1，自引：0，他引：1
在25个室内模型试验基础上,研究了均质砂土中竖向拉拔扩体锚杆的几何尺寸及埋深对其承载特性的影响。试验结果表明,根据深径比的不同,扩体锚杆可以分为浅埋与深埋扩体锚杆2种形式,它们在拉拔过程中均经历了土体弹性变形阶段、非扩体锚固段-土界面剪切破坏阶段、土体弹塑性变形阶段以及剪切破坏阶段,破坏特征分别表现为整体剪切破坏与局部剪切破坏。通过扩体锚杆与普通拉力型锚杆模型试验对比发现：与普通拉力型锚杆相比,扩体锚杆极限承载力、承载比与安全性均有大幅度提高。而通过增大扩体锚固段直径的方式提高扩体锚杆承载力的优势较为明显。此外,根据承载比分析,扩体锚杆存在最优扩体锚固段直径,因此,在实际工程中应寻找一个满足需要的最优扩体锚固段尺寸以取得较好的经济效益。 相似文献
13.
Seyyed Mohammad Mousavi Amir Hossein Alavi Ali Mollahasani Amir Hossein Gandomi 《Engineering Geology》2011,123(4):324
In this study, new empirical equations were developed to predict the soil deformation moduli utilizing a hybrid method coupling genetic programming and simulated annealing, called GP/SA. The proposed models relate secant (Es), unloading (Eu) and reloading (Er) moduli obtained from plate load–settlement curves to the basic soil physical properties. Several models with different combinations of the influencing parameters were developed and checked to select the best GP/SA models. The database used for developing the models was established upon a series of plate load tests (PLT) conducted on different soil types at various depths. The validity of the models was tested using parts of the test results that were not included in the analysis. The validation of the models was further verified using several statistical criteria. A traditional GP analysis was performed to benchmark the GP/SA models. The contributions of the parameters affecting Es, Eu and Er were analyzed through a sensitivity analysis. The proposed models are able to estimate the soil deformation moduli with an acceptable degree of accuracy. The Es prediction model has a remarkably better performance than the models developed for predicting Eu and Er. The simplified formulations for Es, Eu and Er provide significantly better results than the GP-based models and empirical models found in the literature. 相似文献
14.
Soil anchors are commonly used as foundation systems for structures requiring uplift resistance such as transmission towers, or for structures requiring lateral resistance, such as sheet pile walls. Anchors commonly have more than one plate or bearing element and therefore there is a complex interaction between adjacent plates due to overlapping stress zones. This interaction will affect the failure mode and ultimate capacity. However, no thorough numerical analyses have been performed to determine the ultimate pullout loads of multi-plate anchors. By far the majority of the research has been directed toward the tensile uplift behaviour of single anchors (only one plate). The primary aim of this research paper is to use numerical modelling techniques to better understand plane strain multi-plate anchor foundation behaviour in clay soils. A practical design framework for multi-plate anchor foundations will be established to replace existing semi-empirical design methods that are inadequate and have been found to be excessively under or over conservative. This framework can then be used by design engineers to more confidently estimate the pullout capacity of multi-plate anchors under tension loading. 相似文献
15.
New empirical models were developed to predict the soil deformation moduli using gene expression programming (GEP). The principal soil deformation parameters formulated were secant (Es) and reloading (Er) moduli. The proposed models relate Es and Er obtained from plate load-settlement curves to the basic soil physical properties. The best GEP models were selected after developing and controlling several models with different combinations of the influencing parameters. The experimental database used for developing the models was established upon a series of plate load tests conducted on different soil types at depths of 1–24 m. To verify the applicability of the derived models, they were employed to estimate the soil moduli of a part of test results that were not included in the analysis. The external validation of the models was further verified using several statistical criteria recommended by researchers. A sensitivity analysis was carried out to determine the contributions of the parameters affecting Es and Er. The proposed models give precise estimates of the soil deformation moduli. The Es prediction model provides considerably better results in comparison with the model developed for Er. The simplified formulation for Es significantly outperforms the empirical equations found in the literature. The derived models can reliably be employed for pre-design purposes. 相似文献
16.
锚板在正常固结黏土中的承载力 总被引：5，自引：0，他引：5
在岩土工程中,锚板通常被用来提供竖直或水平抗拔力,比如发射塔的基础、板桩墙结构和悬浮式海洋平台的基础。采用弹-塑性有限元方法对正常固结不排水黏土中的条形锚板进行数值分析,以图表形式给出了不同埋深率、不同上拔倾角、不同锚-土黏结形式下条形锚板的承载力系数和周围土体的流动机构,分析了土体自重对锚板承载力的影响,并给出了不同情况下锚板的极限承载力系数。采用基于重新划分网格并插值状态变量的大变形分析方法（RITSS）,分析了正常固结黏土中锚板在连续拔出过程中的承载力变化以及土重对锚-土分离模式的影响。 相似文献
17.
《Geomechanics and Geoengineering》2013,8(4):267-275
Pseudo-static approach is adopted in this paper to determine the seismic uplift capacity of an inclined strip anchor using upper bound limit analysis. Two different failure mechanisms are considered to obtain the magnitudes of unit weight component of uplift factor fγE for different values of soil friction angle, interface friction of anchor plate, anchor inclination, embedment ratio and horizontal seismic acceleration coefficient. The failure mechanism 1 consists of a triangular and quadrilateral rigid blocks; whereas the failure mechanism 2 comprises a logarithmic spiral failure zone with varied focus, sandwiched between a triangular and quadrilateral rigid blocks. It is observed that the magnitude of uplift factor fγE decreases significantly with the increase in seismic acceleration but increases with the increase in embedment ratio and roughness of the anchor surface. However, a mixed trend in the values of fγE can be observed for different inclination of the anchor, which is clearly discussed in this paper. The results are compared with the existing values in the literature and the significance of the present methodology for designing the inclined strip anchor is discussed. 相似文献
18.
随着建筑物地下室的埋深增加、地下水位升高以及极端恶劣天气的影响,对抗浮锚杆的性能提出了更高的要求,传统抗浮锚杆的局限性日益明显。为了解决建筑物因不同区域结构自重和地下室底板埋深差异带来的抗浮难题,本文通过精细分区抗浮设计,采用精轧螺纹钢筋代替普通钢筋的高强度扩大头抗浮锚杆解决了抗浮问题,其单根抗浮锚杆的抗拔承载力为560 kN,在最大试验荷载840 kN作用下锚头最大位移仅为5.25~9.97 mm,平均值为7.91 mm,卸荷后回弹率为18.09%~46.26%,未出现破坏,展现了优越的性能。高强度扩大头抗浮锚杆存在3种类型的应力-应变模式,（压密）-预应力抵消-扩大头端压是抗浮锚杆的理想应力-应变模式,其在1120 kN荷载作用下仍能保持正常维持收敛,且抗拔承载力为560 kN时仅处于预应力抵消阶段,仍具有很大的承载潜力。 相似文献
19.
The undrained shear strength (s u) of cohesive soils is a crucial parameter for many geotechnical engineering applications. Due to the complexities and uncertainties associated with laboratory and in situ tests, it is a challenging task to obtain the undrained shear strength in a reliable and economical manner. In this study, a probabilistic model for the s u of moderately overconsolidated clays is developed using the Bayesian model class selection approach. The model is based on a comprehensive geotechnical database compiled for this study with field measurements of field vane strength (s u), plastic limit (PL), natural water content (W n), liquid limit (LL), vertical effective overburden stress (\(\sigma_{\nu }^{\prime }\)), preconsolidation pressure (\(\sigma_{\text{p}}^{\prime }\)) and overconsolidated ratio (OCR). Comparison study shows that the proposed model is superior to some well-known empirical relationships for OC clays. The proposed probabilistic model not only provides reliable and economical estimation of s u but also facilitates reliability-based analysis and design for performance-based engineering applications. 相似文献
20.
为了确定软土中张紧式吸力锚的破坏标准,采用自主研发的电动伺服加载装置,在荷载和位移控制方式下进行了张紧式吸力锚在最佳系泊点受静荷载作用的承载力模型试验。结果表明：不同的破坏模式,锚破坏时对应的位移也不同。当锚为竖向破坏时,对应锚沿系泊方向的位移约为0.6倍的锚径;当锚为水平破坏时,对应锚沿系泊方向的位移约为0.3倍的锚径。同时,按照模型试验所得的破坏标准确定的吸力锚的极限承载力与极限分析法的预测结果吻合较好。对足尺锚进行了有限元分析,将分析结果与极限分析法的预测结果进行比较,验证了模型试验所得位移破坏标准的合理性。 相似文献