共查询到20条相似文献，搜索用时 15 毫秒
1.
Yannis F. Dafalias Majid T. Manzari Achilleas G. Papadimitriou 《国际地质力学数值与分析法杂志》2006,30(12):1231-1257
SANICLAY is a new simple anisotropic clay plasticity model that builds on a modification of an earlier model with an associated flow rule, in order to include simulations of softening response under undrained compression following Ko consolidation. Non‐associativity is introduced by adopting a yield surface different than the plastic potential surface. Besides, the isotropic hardening of the yield surface both surfaces evolve according to a combined distortional and rotational hardening rule, simulating the evolving anisotropy. Although built on the general premises of critical state soil mechanics, the model induces a critical state line in the void ratio–mean effective stress space, which is a function of anisotropy. To ease interpretation, the model formulation is presented firstly in the triaxial stress space and subsequently, its multiaxial generalization is developed systematically, in a form appropriate for implementation in numerical codes. The SANICLAY is shown to provide successful simulation of both undrained and drained rate‐independent behaviour of normally consolidated sensitive clays, and to a satisfactory degree of accuracy of overconsolidated clays. The new model requires merely three constants more than those of the modified Cam clay model, all of which are easily calibrated from well‐established laboratory tests following a meticulously presented procedure. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
2.
This paper presents a new generalized effective stress model, referred to as MIT-S1, which is capable of predicting the rate independent, effective stress–strain–strength behaviour of uncemented soils over a wide range of confining pressures and densities. Freshly deposited sand specimens compressed from different initial formation densities approach a unique condition at high stress levels, referred to as the limiting compression curve (LCC), which is linear in a double logarithmic void ratio, e, mean effective stress space, p′. The model describes irrecoverable, plastic strains which develop throughout first loading using a simple four-parameter elasto-plastic model. The shear stiffness and strength properties of sands in the LCC regime can be normalized by the effective confining pressure and hence can be unified qualitatively, with the well-known behaviour of clays that are normally consolidated from a slurry condition along the virgin consolidation line (VCL). At lower confining pressures, the model characterizes the effects of formation density and fabric on the shear behaviour of sands through a number of key features: (a) void ratio is treated as a separate state variable in the incrementally linearized elasto-plastic formulation: (b) kinematic hardening describing the evolution of anisotropic stress–strain properties: (c) an aperture hardening function controls dilation as a function of ‘formation density’; and (d) the use of a single lemniscate-shaped yield surface with non-associated flow. These features enable the model to describe characteristic transitions from dilative to contractive shear response of sands as the confining pressure increases. This paper summarizes the procedures used to select input parameters for clays and sands, while a companion paper compares model predictions with measured data to illustrate the model capability for describing the shear behaviour of clays and sands. Copyright © 1999 John Wiley & Sons, Ltd. 相似文献
3.
The objective of this study is to derive an effective stress‐based constitutive law capable of predicting rate‐dependent stress–strain, stress path and undrained shear strength and creep behavior. The flow rule used in the MIT‐E3 model and viscoplasticity theory is employed in the derivation. The model adopts the yield surface capable of representing the yield behavior of the Taipei silty clay and assumes that it is initially symmetric about the K0‐line. A method is then developed to compute the gyration and expansion of the loading surface to simulate the anisotropic behavior due to the principal stress rotation after shear. There are 11 parameters required for the model to describe the soil behavior and six of them are exactly the same as those used in the Modified Cam‐clay model. The five additional parameters can be obtained by parametric studies or conventional soil tests, such as consolidation tests, triaxial compression and extension tests. Finally, verification of the model for the anisotropic behavior, creep behavior and the rate‐dependent undrained stress–strain and shear strength of the Taipei silty clay is conducted. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
4.
5.
S. K. Ghosh 《Journal of Earth System Science》1995,104(3):373-383
During the refolding of an early non-isoclinal fold (say,F
1) we may find an offset or side-stepping of the axial surfaces of the later folds (say,F
2). The offsets can be seen in both type 2 and type 3 interference patterns. An analysis of the shear fold model shows that
there is a maximum limit for the magnitude of side-stepping. The side-stepping is larger for larger interlimb angles ofF
1. It decreases with progressive tightening ofF
2. By recognizing such side-stepping we can predict on which side the F1 hinge should lie even if the hinge is unexposed or lies outside the domain of observation. The general rule for the sense
of side-stepping is the same for shear folds, flexural slip folds and buckling folds. However, the side-stepping in buckling
folds should be used with caution, sinceF
2 folds on buckled single-layers may show an offset whose sense is opposite to that predicted by the general rule. 相似文献
6.
Non‐associated flow rule is essential when the popular Mohr–Coulomb model is used to model nonlinear behavior of soil. The global tangent stiffness matrix in nonlinear finite element analysis becomes non‐symmetric when this non‐associated flow rule is applied. Efficient solution of this large‐scale non‐symmetric linear system is of practical importance. The standard Krylov solver for a non‐symmetric solver is Bi‐CGSTAB. The Induced Dimension Reduction [IDR(s)] solver was proposed in the scientific computing literature relatively recently. Numerical studies of a drained strip footing problem on homogenous soil layer show that IDR(s = 6) is more efficient than Bi‐CGSTAB when the preconditioner is the incomplete factorization with zero fill‐in of global stiffness matrix Kep (ILU(0)‐Kep). Iteration time is reduced by 40% by using IDR(s = 6) with ILU(0)‐Kep. To further reduce computational cost, the global stiffness matrix Kep is divided into two parts. The first part is the linear elastic stiffness matrix Ke, which is formed only once at the beginning of solution step. The second part is a low‐rank matrix Δ, which is re‐formed at each Newton–Raphson iteration. Numerical studies show that IDR(s = 6) with this ILU(0)‐Ke preconditioner is more time effective than IDR(s = 6) with ILU(0)‐Kep when the percentage of yielded Gauss points in the mesh is less than 15%. The total computation time is reduced by 60% when all the recommended optimizing methods are used. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
7.
Determination of Shear Strength and Three-dimensional Yield Strength for the Hoek-Brown Criterion 总被引：1，自引：3，他引：1
S. D. Priest 《Rock Mechanics and Rock Engineering》2005,38(4):299-327
Summary. Most currently used techniques for analysing the stability of near surface structures, such as rock slopes, are based on the application of the effective Coulomb shear strength parameters cohesion c′, and the angle of friction φ′ on some known or anticipated shear surface subjected to an effective normal stress σ′n. The most widely used of these techniques are the variants of the method of slices and related upper bound techniques. If the Hoek-Brown criterion is to be used to model the strength of near surface fractured rocks, it is necessary to determine equivalent Coulomb shear strength parameters for the specified level of effective normal stress. Calculation of the equivalent Coulomb parameters for the Hoek-Brown criterion for cases when a ≠ 0.5 is not a straightforward matter. A simple procedure for calculating instantaneous values of c′i and φ′i has been developed based on spreadsheet calculations and the application of a numerical optimisation routine. This procedure can also be applied to calculating the Hoek-Brown envelope plotted in shear stress/normal stress space. A simple closed form solution for c′i and tan φ′i has also been developed for the special case when a = 1. A three-dimensional version of the Hoek-Brown criterion has been developed by combining it with the Drucker-Prager criterion. This new yield criterion has been implemented by numerical solution of the governing equations. A simplification of this three-dimensional yield criterion has been developed by introducing an intermediate principal stress weighting factor. Comparison with published results demonstrates that this simplified criterion has the capacity to model the results of true triaxial tests for a range of different rock types over a wide range of stress levels. The new three-dimensional yield criterion has the advantage that its input parameters can be determined from routine uniaxial compression tests and mineralogical examination. 相似文献
8.
9.
Analytical solutions for the steady‐state response of an infinite beam resting on a visco‐elastic foundation and subjected to a concentrated load moving with a constant velocity are developed in this paper. The beam responses investigated are deflection, bending moment, shear force and contact pressure. The mechanical resistance of the foundation is modeled using two parameters ks and ts — ks accounts for soil resistance due to compressive strains in the soil and ts accounts for the resistance due to shear strains. Since this model represents the ground behavior more accurately than the Winkler spring model, the developed solutions produce beam responses that are closer to reality than those obtained using the existing solutions for Winkler model. The dynamic beam responses depend on the damping present in the system and on the velocity of the moving load. Based on the study, dynamic amplification curves are developed for beam deflection. Such amplification curves for deflection, bending moment, shear force and contact pressure can be developed for any beam‐foundation system and can be used in design. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
10.
The implications of assuming isotropic elasto–plasticity to model the behaviour of soil under simple shear conditions are considered. For small strains, use of such a model implies the following three consequences: (1) strains and strain increments at any stage of shearing may be expressed as the sum of elastic and plastic components; (2) principal directions of stress and of plastic strain increment are collinear; (3) principal directions of stress increment and of elastic strain increment are collinear. These consequences are used in order to establish relationships between the stresses, stress increments and strains which develop in a simple shear test. No additional assumptions with regards the form of the yield function, the flow rule or the hardening function are required for this development. By defining the ratio of the plastic to the total shear strain increment on the horizontal plane (the plane of zero extension) as λ, it is possible to define the horizontal normal stress σx in terms of λ and other stresses and strains which are normally known during simple shear loading. As a result, all components of the stress tensor in the simple shear plane may be defined. Results of some direct simple shear tests on soft clay have been interpreted using the model and found to be generally consistent with some of the observations reported in the literature from tests in which boundary stresses were measured. 相似文献
11.
Numerous constitutive models built on coaxial theory and validated under axi‐symmetric condition often describe the stress–stain relationships and predict the inceptions of shear banding in sands inaccurately under true triaxial condition. By adopting an elaborated Mohr–Coulomb yield function and using non‐coaxial non‐associated flow rule, a 3D non‐coaxial elasto‐plasticity model is proposed and validated by a series of true triaxial tests on loose sands. The bifurcation analysis of true triaxial tests on dense sands predicts the influence of the intermediate principal stress ratio on the onset of shear band accurately. The failure of soils is shown to be related to the formation of shear band under most intermediate principal stress ratio conditions except for those which are close to the axi‐symmetric compression condition. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
12.
The paper presents a comparison between the behavior of slurry-consolidated Kaolin specimens tested under axisymmetric Conventional
Triaxial Compression (CTC) and Plane Strain (PS) loading conditions. The PS experiments were conducted on an instrumented
apparatus capable of capturing the onset of shear bands. The specimens were consolidated and then sheared under undrained
condition. The PS specimens failed via a well-defined shear band that began to develop during the hardening stress regime
whereas CTC specimens failed through a diffuse bulging mode. The undrained shear strength (S
u) of CTC experiments is smaller than the S
u of PS experiments. However, the normalized S
u of CTC experiments is very close to PS1, which was consolidated under similar K
o condition. 相似文献
13.
This article presents the development of a J2 small strain plasticity model based on bounding surface concept, along with numerical examples to demonstrate model behaviors and identification of model parameter using laboratory test data. The model is motivated by the need for simulating permanent deformation accumulation of asphalt concrete mixtures, which leads to rutting in flexible pavements under repeated traffic loading. The proposed model accounts for the observation that rutting is mostly caused by shearing and takes advantage of the fact that bounding surface concept allows for the progressive accumulation of plastic deformation under constant amplitude loading condition. Analytical solutions are given for typical laboratory testing conditions. The model can be calibrated using repeated simple shear test data that are typically available for asphalt concrete mixtures. It is shown that the model is easy to use and provides a promising alternative for modeling permanent deformation accumulation in materials subjected to repetitive (cyclic) loading. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
14.
15.
A three-dimensional kinematic limit analysis approach based on the radial point interpolation method (RPIM) has been used to compute collapse loads for rectangular foundations. The analysis is based on the Mohr-Coulomb yield criterion and the associated flow rule. It is understood that the internal plastic power dissipation function and flow rule constraints can be expressed entirely in terms of plastic strain rates without involving stresses. The optimization problem has been solved on basis of the semidefinite programming (SDP) by using highly efficient primal-dual interior point solver MOSEK in MATLAB. The results have been presented in terms of the variation of the shape factors with changes in the aspect ratio (L/B) of the footing for different values of soil internal friction angle (ϕ). Computations have revealed that the shape factors, sc and sq, due to effects of cohesion and surcharge increase continuously with (1) decrease in L/B and (2) increase in ϕ. On the other hand, the shape factor sγ, due to the effect of soil unit weight, increases very marginally with an increase in L/B up to (1) ϕ = 25° for a rough footing and (2) ϕ = 35° for a smooth footing. Thereafter, for greater values of ϕ, the variation of sγ with L/B has been found to be quite similar to that of the factors sc and sq. The variations of (1) nodal velocity patterns, (2) plastic power dissipation, and (3) maximum plastic shear strain rates have also been examined to interpret the associated failure mechanism. 相似文献
16.
In general, pile materials are assumed to be isotropic during the analysis of the load–deflection response of piles under lateral loads. However, commonly used materials such as reinforced concrete and timber as well as potentially promising new pile materials such as fiber reinforced polymers are typically transversely isotropic materials. Experimental studies have shown that transversely isotropic materials have a high ratio of section longitudinal modulus to the section in‐plane shear modulus (Ezz/Gxz) compared to the value for isotropic materials. The high modulus ratio leads to a more significant shear deformation effect in beam bending. To account for the shear deformation effect, the Timoshenko Beam Theory has been adopted in deriving the solutions for the load–deflection response of transversely isotropic piles under lateral loads instead of the Classical (Euler–Bernoulli) Beam Theory. The load–deflection responses depend on the shear effect coefficient, the lateral soil resistance, the embedment ratio, and the boundary conditions. The deflection of the pile, if the shear deformation effect is considered, is always larger than if it is neglected. Copyright © 2000 John Wiley & Sons, Ltd. 相似文献
17.
The yield vertex non‐coaxial theory is implemented into a critical state soil model, CASM (Int. J. Numer. Anal. Meth. Geomech. 1998; 22 :621–653) to investigate the non‐coaxial influences on the stress–strain simulations of real soil behaviour in the presence of principal stress rotations. The CASM is a unified clay and sand model, developed based on the soil critical state concept and the state parameter concept. Without loss of simplicity, it is capable of simulating the behaviour of sands and clays within a wide range of densities. The non‐coaxial CASM is employed to simulate the simple shear responses of Erksak sand and Weald clay under different densities and initial stress states. Dependence of the soil behaviour on the Lode angle and different plastic flow rules in the deviatoric plane are also considered in the study of non‐coaxial influences. All the predictions indicate that the use of the non‐coaxial model makes the orientations of the principal stress and the principal strain rate different during the early stage of shearing, and they approach the same ultimate values with an increase in loading. These ultimate orientations are dependent on the density of soils, and independent of their initial stress states. The use of the non‐coaxial model also softens the shear stress evolutions, compared with the coaxial model. It is also found that the ultimate shear strengths by using the coaxial and non‐coaxial models are dependent on the plastic flow rules in the deviatoric plane. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
18.
原型监测表明面板堆石坝一般存在比较显著的流变现象。针对不同文献给出的堆石料三维剪切流变速率计算式存在差异,笔者以3参数指数流变模型为例对堆石料三维流变速率进行了研究。假设体积流变和剪切流变变化规律不同,首先推导了三维体积流变速率计算公式,然后依据Prandtl-Reuss流动法则可以由Mises屈服函数作为塑性势函数推导获得。为此,采用关联流动法则,同时假设塑性势函数为Mises屈服函数,导出了堆石料三维剪切流变速率计算式。通过将三维流变速率计算式退化为单轴流变速率计算式进行合理性分析,分析表明,本文导出的三维流变速率计算式理论上是严谨的,由此指出相关文献给出的流变速率计算式理论上不严谨。 相似文献
19.
The main purpose of the paper is to present a relatively simple, yet realistic, constitutive model for simulations of structured sensitive clays. The proposed constitutive model can simulate 1‐D and isotropic consolidation, and drained and undrained shear response of sensitive structured clay. The proposed sensitive bounding surface model is based on concepts from the modified Cam clay model 8 and bounding surface plasticity 27 , with the addition of a simple degradation law. The key material parameters are M, λ, κ, and ν from the modified Cam clay framework, h from the bounding surface framework to model a smoothed elasto‐plastic transition, and ωv, ωq, and Ssr to model softening associated with destructuration. The model has separate parameters to model destructuration caused by volumetric strain and deviatoric strain. The model is capable of modeling unusual behavior of strain softening during 1‐D compression (i.e., a reduction of effective stress as void ratio decreases). A good match between test results and the model simulation is demonstrated. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
20.
Liquefaction resistance of granular soils is commonly characterized by the cyclic resistance ratio (CRR) in the simplified shear stress procedure of liquefaction potential assessment. This parameter is commonly estimated by cyclic tests on reconstituted samples or empirical correlations between liquefied/non-liquefied case histories. The current study employs results of cyclic triaxial tests on reconstituted soil specimens and presents a predictive equation for cyclic resistance ratio (CRR) of clean and silty sands. The CRR equation is a function of relative density, effective mean confining pressure, non-plastic fines content, number of harmonic cycles for liquefaction onset, and some other basic soil properties. It is demonstrated that the developed relationship obtains reasonable accuracy in the prediction of laboratory-based CRR. Based on the developed CRR model, new relationships are then presented for the coefficient of effective overburden pressure (Kσ) and magnitude scaling factor (MSF), two important modification factors in the simplified shear stress procedure. These new modification factors are then compared with those recommended by previous researchers. Finally, the possible application of the proposed CRR model in field condition is shown for a specific case. This study provides a preliminary insight into the liquefaction resistance of silty sands prior to the complementary laboratory studies. 相似文献