首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
基于物理和常规变形特性分析,认为某水电站坝基碎屑岩力学特性异常复杂,故采用岩石三轴伺服仪开展了系列的蠕变力学特性试验研究。首先,探讨了轴向、侧向及体积蠕变特性和速率变化规律;其次,分析了蠕变对偏应力-应变特性影响并开展了破坏岩样微细观电镜扫描试验;最后,在采用等时曲线簇法确定长期强度的基础上,以实际延性扩容为依据,认为岩石侧向体积扩容速率大于轴向压缩速率的临界点为快速蠕变破坏的标志,提出确定长期强度的新方法。结果表明,碎屑岩表现出显著的蠕变特性,蠕变曲线主要分为初始衰减和稳态蠕变两阶段,且最后一级应力施加后呈现加速蠕变现象;应力增加导致蠕变变形加剧,最终破坏表现出轴向压缩变形过大、体积延性扩容明显、稳态蠕变速率较大等特点,且蠕变速率与应力符合指数函数关系。岩样长期强度与三向稳态蠕变速率交点和侧向体积扩容应力阀值基本一致,为常规强度的54%~80%。试验结果旨在为相关岩石工程长期稳定分析及蠕变模型构建提供可靠的依据。  相似文献   

2.
本文对取自雅砻江锦屏二级电站的砂岩开展三轴压缩流变实验,并分析了实验数据,得到不同偏应力条件下砂岩轴向应变、侧向应变、轴向应变率和侧向应变率随时间的变化规律。并用Burgers体来反映瞬态蠕变阶段、稳态蠕变阶段的蠕变,进行了参数辨识,为工程围岩长期稳定性分析提供理论基础。  相似文献   

3.
利用室内试验研究土体蠕变特性时,因受试验条件限制较少开展土体的排水蠕变特性试验研究。对于先还原土体的先期固结条件,然后再开展土体的三轴排水蠕变特性试验的研究更少。为此,以淤泥土为研究对象,通过 固结三轴排水蠕变试验探讨了饱和淤泥土在轴向加载和侧向减载条件下的排水蠕变特性。由试验数据可知:排水条件下,两种应力路径的轴向蠕变规律基本一致,体积应变明显小于轴向应变,且随时间的延长呈现一定程度的剪缩与剪胀交替性。首次利用三单元力学模型推测出淤泥土的蠕变起始时间为施加偏应力荷载后的100~200 min之间。提出淤泥土蠕变系数的概念并总结其变化规律,得知淤泥土的蠕变系数与偏应力水平密切相关,即不论围压及加载方式如何,蠕变系数均随应力水平增大而增大,且基本呈直线关系,而与前期固结围压大小、蠕变荷载施加方式关系不大。最后提出了淤泥土蠕变本构模型建立的思路,即用南水双屈服面模型描述瞬时变形量和用蠕变经验公式描述蠕变变形量相结合的方式来建立蠕变本构模型。  相似文献   

4.
The altered granite gneiss is a special rock with loosely-structured and well-developed pores and cavities. The microstructure and mineral composition of the rock were analysed by SEM-EDS and creep triaxial tests were carried out and the axial and lateral deformations over time were discussed. Both the axial and the lateral creep curves show the typical three distinct creep stages (decay creep, steady state creep, accelerated creep). At a low stress level, the axial creep strain is unnoticeable, and only when loaded at a high stress level will the creep strain increase at an increasing rate until the rock specimen fails. The lateral creep strain is smaller than the axial creep strain, but the creep rate (dε/dt) in the lateral direction is higher than that in the axial direction at all stress levels. The failure pattern, which is affected by many factors, shows a shear failure with rather broken and rough failure surfaces.  相似文献   

5.
在锦屏二级水电站辅助洞绿片岩的双轴压缩蠕变试验结果的基础上,研究了应力路径对双轴压缩蠕变变形的影响。结果表明:当侧向应力相同时,随着轴向应力的增加,轴向稳态蠕变阶段的变形速率逐渐增加;当轴向应力相同时,随着侧向应力的增加,轴向稳态蠕变阶段的变形速率逐渐减小。  相似文献   

6.
对石英云母片岩进行三轴压缩蠕变试验,研究丹巴水电站石英云母片岩的三轴蠕变特性及其各向异性特性。按轴向荷载与层理面关系加工成平行组和垂直组2组试件,开展分级加载方式进行不同围压条件下的蠕变试验。试验研究表明,石英云母片岩具有蠕变特性,包括瞬时变形、衰减蠕变、稳定蠕变和加速蠕变阶段;采用带Kachanov蠕变损伤律的蠕变模型来描述石英云母片岩的蠕变特性,并进行蠕变参数辨识,拟合结果显示此模型能很好地描述石英云母片岩的蠕变特性;根据试验结果获得2组试件的长期屈服强度、破坏形态、瞬时变形参数和稳定蠕变速率,分析表明石英云母片岩的蠕变力学特性具有明显的各向异性特性。层理面与轴向荷载垂直的试件较层理面与轴向荷载平行的试件的强度、弹性剪切模量、体积模量和黏性系数相对较大,表现出较高的抗变形和抗破坏能力;平行组以剪切破坏为主,垂直组破坏时出现侧向鼓胀现象,显示出延性破坏的特点;2组石英云母片岩试件的瞬时应变量和稳定蠕变速率都随着应力水平的提高而增大。  相似文献   

7.
为研究深部巷道围岩在地下水作用下的长期蠕变力学特性,采用自主研制的深部软岩五联流变试验系统,开展不同含水率(0%、0.8%、1.6%、2.4%、3.3%)下砂岩吸水软化单轴压缩试验及单轴蠕变试验。通过试验结果研究表明:砂岩的单轴抗压强度、弹性模量和蠕变破坏应力与含水率呈指数下降关系,蠕变破坏应力与单轴抗压强度的比值在0.76~0.84之间;砂岩衰减蠕变阶段时间随着含水率的增加而减少,随应力水平的增加而增加。径向应变比轴向应变先进入稳态蠕变阶段,破坏应力下径向应变的加速蠕变阶段开始时间要先于轴向应变;基于稳态蠕变速率曲线确定了砂岩的长期强度,径向稳态蠕变速率确定的值略小于轴向,长期强度与含水率之间满足负指数关系;将蠕变试验中径向应变与轴向应变之比定义为μc,提出了基于μc值的岩石长期强度确定方法且μc值与含水率无关,对于本次砂岩样品可以认为μc值大于0.3时样品会在一定时间内发生加速蠕变破坏;随着含水率的增加,样品破坏形态由单斜面剪切破坏逐渐演变至X状共轭斜面剪切破坏。研究结果为地下水作用下巷道长期稳...  相似文献   

8.
In the each loading stage, strain and creep strain occurs instantaneously on the axial and lateral of fractured. Instantaneous strain leads to the 80% overall specimen deformation. The axial strain is about 2–3 times larger than the lateral strain. Instantaneous strain completed time and deformations under each loading stage decrease when the loading time increases. With the increasing of loading, axial strain and lateral strain of fractured phyllite present the approximate linear curve growth change. With increasing of axial stress, the relationship between the lateral strain and axial strain transform from the linear increased trend to the index increased trend. With the increasing of moisture content, the axial deformation and lateral deformation of fractured phyllite increase. The curves of axial strain and lateral strain under soaked for 10 and 15 days condition are similar. The modified Burgers model can describe each creep stage of fractured phyllite which have high fitting precision, less fluctuation and high reliability. Therefore, modified Burgers model can provide an effective way to analyze the creep characteristics of fractured phyllite.  相似文献   

9.
Microstructures in naturally deformed rocks in the upper crust demonstrate that creep strain in nature may be accommodated by a combination of dislocation creep, diffusion/dissolution processes and microcracking. A theoretical approach towards deriving an aggregate flow law is presented, where the strain in the constituent phases is assumed to occur by simultaneous operation of diffusive mass transfer and crystal plastic mechanisms (dislocation creep). Both uniform stress and uniform strain rate situations are considered.  相似文献   

10.
Rock reinforcement systems, such as resin-grouted rock bolts, display complex creep behavior because both grouting materials and bolts show time-dependent behavior. In this paper, only the time-dependent behavior of grouting material was investigated, in which creep tests of grouting material was conducted in triaxial compression apparatus at room temperature. The test specimens were provided from the Araldite epoxy resin used in rock reinforcement. We attempt to predict long-term creep parameter using triaxial creep tests and to define time-dependent characteristics of the bounding material. In short-term creep tests, three different axial and confining stress levels were applied in steps to each specimen. The transient creep for all the stress levels were described by power function which fit properly to time–strain curves. The maximum difference between the proposed model and experimental long-term creep strain was less than 7.1 %. It was observed that the creep rate of a grouting material specimen directly depends on the deviator of stress (i.e., σ1–σ3).  相似文献   

11.
En echelon crack-arrays in potash salt rock   总被引:1,自引:0,他引:1  
Summary There are two types of fracture patterns in the yield pillars of the potash mines of Saskatchewan. The individual members of both patterns are tensile (extension) fractures that propagate parallel with the maximum principal stress trajectory (perpendicular to the minimum principal stress). The difference between the two patterns lies in the arrangement of the member fractures. In theen echelon tensile crack-array, the macroscopic fracture consists of individual tensile cracks that are slightly offset from each other. They have only a small overlap and the child crack seems to form randomly on either side of its parent. Consequently, the en echelon tensile crack-array inherits the axial orientation of its members. In contrast, the tensile cracks of anen echelon shear crack-array, have a larger overlap and their lateral displacement from each other is biased in one direction. Therefore, the crack-array is no longer axial but inclined 20–25 degrees from the maximum principal stress direction. With increasing stress, the shear crack-array often collapses, forming theenvelope orhourglass structures of the potash mines.  相似文献   

12.
王康宇  庄妍  耿雪玉 《岩土力学》2020,41(6):1865-1873
粗粒土填料被广泛应用于铁路基床填料中,直接承受轨道结构传递的列车动循环荷载的长期作用,研究其在列车动荷载作用下的动力行为特征及塑性变形特性可为路基状态评估、沉降控制提供思路。采用GDS动三轴试验系统对铁路基床表层的粗粒土填料动力响应开展研究,通过引入塑性应变率和安定理论,将不同频率、围压、循环动应力比等条件下路基填料的轴向塑性应变的发展规律划分为塑性安定、塑性蠕变和增量塑性破坏3种类型,并确定了塑性安定和塑性蠕变状态的临界动应力水平。研究表明:粗粒土填料的临界循环应力比随着围压的增大而增大,随着荷载频率的增加而减小。通过对试验结果的拟合分析,提出了以围压为变量的临界动应力经验公式,为合理评估列车荷载作用下路基任意深度的动力稳定提供了理论依据。  相似文献   

13.
软硬相接岩层在长时间跨度内的蠕变变形可能极为不协调,这对开挖工程安全稳定造成严重威胁。对某水电站引水隧洞同一开挖断面内砂质泥岩和泥质砂岩两种软硬相差较大的岩石进行卸荷条件下的蠕变试验和数值模拟,结果表明:在卸围压条件下,试样侧向蠕变变形较轴向发展更为迅速,呈现出显著的侧向扩容;初始围压水平较高时,试样卸荷蠕变破坏的侧向扩容效应更加显著;泥质砂岩在稳态蠕变阶段变形速率比砂质泥岩更慢,蠕变破坏时的应变值均比砂质泥岩蠕变破坏时的应变值要小,征兆性更弱。基于Burgers模型,引入损伤变量,建立带损伤的蠕变本构模型,模型曲线较好地描述了岩石破坏偏应力水平之前的线性蠕变特征和破坏偏应力水平下的非线性加速蠕变特征;软硬相接岩层蠕变数值模拟表明,蠕变变形初期,软硬相接点变形差别幅度不大,随着时间增长,在交接面处发生层间错动,对围岩整体稳定十分不利,工程实践中应予以足够关注。  相似文献   

14.
李晓照  班力壬  戚承志 《岩土力学》2020,41(12):3987-3995
高渗透压对深部地下工程脆性岩石蠕变力学特性有着重要影响。然而,能够解释高渗透压作用脆性岩石完整减速、稳态及加速三级蠕变过程中,细观裂纹扩展与宏观变形关系的宏细观力学模型研究很少。基于考虑含有初始裂纹与新生成翼型裂纹影响的裂纹尖端应力强度模型,引入渗透水压与初始裂纹及新生成翼型裂纹之间的力学关系,建立了考虑渗透水压作用的裂纹尖端应力强度模型;然后结合亚临界裂纹扩展法则,与裂纹及应变损伤关系模型,推出了考虑渗透水压影响的脆性岩石蠕变裂纹扩展与宏观变形关系的宏细观力学模型。当施加轴向应力小于岩石裂纹启裂应力时,岩石近似表现为线弹性变形;当施加轴向应力大于裂纹启裂应力且小于岩石峰值强度,岩石表现为塑性蠕变变形。研究了不同渗透压作用下,分级轴向应力加载岩石蠕变应变时间演化曲线,并通过试验结果验证了模型的合理性。分别讨论了恒定渗透压与分级渗透压,对脆性岩石蠕变过程中裂纹长度、裂纹扩展速率、轴向应变及轴向应变率的影响。该模型为高渗透压深部地下工程围岩稳定性评价提供了重要理论依据。  相似文献   

15.
A series of triaxial creep tests were conducted on warm frozen silts extracted from Qinghai–Tibet Plateau at temperature of ?1.5 °C under confining pressures of 0.5, 1.0, and 2.0 MPa, respectively. The applied test stress levels were 30, 50, 60, and 70% of triaxial shear strength, respectively. The test results indicate that the creep strain increases with the increase in applied stress level and there is a stress threshold, based on which the test results can be classified into two types of creep strain curves. The creep strain curve only includes primary and secondary creep stages when the stress level is less than the threshold value. When the stress level exceeds the threshold value, the creep strain velocity gradually increases and the specimen quickly fails in tertiary creep stage. Based on the creep test results, a fractional order rheological element model is established for warm frozen silt, which is also generalized from uniaxial stress state to the three-dimensional stress state. From the analysis on the features of the stress threshold, a creep strength criterion is also proposed simultaneously. Comparing the calculated results of the warm frozen silt with the tested ones, it is found that the predicted results of the proposed model are in good agreement with the test results. In the proposed fractional order model, the relationship between the damage factor and time is established to describe the damage degree of the specimen. Compared with the existing creep constitutive model of frozen soil, the proposed fractional order model has advantages of fewer model parameters, higher simulation precision and wider applicability in analyzing the mechanical properties of warm frozen silt.  相似文献   

16.
冻结砂土在动荷载下的蠕变特征   总被引:9,自引:3,他引:6  
通过分析不同试验条件下的蠕变过程曲线,探讨了冻结砂土在动荷载下的蠕变模型,分析了最大加载应力,温度及加载频率对冻土蠕变破坏应变,破坏时间和最小蠕变速率的影响.结果表明,当最大加载应力变大时,破坏应变增加,破坏时间缩短,最小蠕变速率变快;加载条件相同时,温度越低,破坏应变越小,破坏时间越长,最小蠕变速率越小;加载频率变化时,最小蠕变速率的变化无明显规律,都在一个量级范围内,当频率变大时,最小蠕变速率略有变小的趋势.频率增加,破坏时间缩短,破坏应变减小.频率小于7Hz时,频率对破坏应变和破坏时间影响较大,而当频率大于7Hz时,随频率加快,破坏时间和破坏应变只略有减小.  相似文献   

17.
主应力旋转将加速孔压和塑性应变的累积,影响土体的力学特性。为研究主应力轴循环旋转对 固结饱和粉质黏土孔压和变形的影响,利用GDS-HCA试验系统开展了不同应力路径的 固结饱和粉质黏土不排水循环三轴试验和循环扭剪试验,研究了主应力轴循环旋转对 固结饱和粉质黏土累积塑性应变、孔压等动力特性的影响。结果表明:动剪应力幅值、心形应力路径所包围的面积、循环偏应力幅值等均随循环剪应力比和循环动应力比的增大而增大。试样未发生破坏时, 固结饱和粉质黏土的孔压比随着振动荷载作用次数的增加而增大;当试样发生破坏时,孔隙压力迅速消散,孔压比急剧下降。循环扭剪试验时试件产生的轴向累积塑性应变始终大于循环三轴试验产生的累积塑性应变,说明主应力轴循环旋转会加速试件轴向应变的累积。试件的累积塑性应变随循环剪应力比和循环动应力比的增大而增大。循环动应力比越大时,主应力轴旋转造成的轴向累积塑性应变差异越显著。在Monismith幂次函数模型的基础上,建立了主应力轴循环旋转条件时K0固结饱和粉质黏土累积塑性应变方程,并对模型的可靠性进行了分析和验证。  相似文献   

18.
岩石蠕变是其内部硬化效应和损伤效应共同作用演化的结果。通过分级加载下贫煤单轴压缩蠕变试验,基于试验中瞬时弹性模量增大和黏滞系数减小的现象,分析贫煤蠕变中的硬化-损伤机制。结果表明,较低应力下煤样的变形仅为瞬时应变,煤样仅有硬化效应;当应力达到蠕变起始应力阈值时煤样逐渐出现损伤,次生裂纹出现并扩展,硬化效应与损伤效应共同作用下煤样表现出衰减蠕变和稳定蠕变特征。长期蠕变过程中煤样强度经历先硬化再弱化的过程,最终因累计损伤过大而失稳破坏,依据各级应力下煤样的变形特征,构建了符合其变形规律的黏弹塑性组合模型,并引入了硬化函数和损伤函数,推导得到其蠕变本构方程。采用该模型描述分级加载下贫煤单轴压缩蠕变变形曲线,试验曲线和模型曲线吻合良好。该模型元件简单,物理意义明确,能很好地反映贫煤单轴压缩下的硬化–损伤蠕变特性。  相似文献   

19.
Rocks subjected to long-term loading have been known to suffer microcracking. The rate of cracking is sensitive to the type of the applied stress (tensile or compressive), and the magnitude of the stress relative to the instantaneous strength. In addition, crack growth is influenced by the environment (pressure and temperature) including the presence or absence of moisture.For tensile loading, the sensitivity of granite to time-dependent cracking is demonstrated through a fracture mechanics test known as double torsion. The crack velocity versus stress intensity function is established for two environments, room temperature and humidity and room temperature and 100 percent humidity.For compressive loading, time dependent cracking is evaluated from creep tests conducted in uniaxial compression in the same two environments. The rate of cracking is defined by finding the functional relationship between the rate of crack growth, expressed as the rate of crack volume strain, and uniaxial compressive stress.A variety of mathematical functions has been fitted to the obtained data. The traditionally-used power and exponential relationships give good correlation for both crack velocity and crack volume strain rate.The crack volume strain rate versus stress function can be integrated to obtain a lifetime estimate for Lac du Bonnet granite. After 1 000 years of loading in uniaxial compression at room temperature and 100 percent humidity, the strength of this granite could reduce from 225 MPa to 90–100 MPa.  相似文献   

20.
甘肃黑方台地区是中国滑坡预测预报研究和实践的热点地区,开展黄土时效特性试验是进行滑坡预测预报的基础.以黑方台原状黄土为研究对象,开展了2个含水量、4个围压、八级偏应力水平下的黄土三轴固结排水蠕变试验,研究了黑方台黄土的粘-弹-塑性变形破坏规律.蠕变试验结果表明,相同含水量和围压下,偏应力越大时,黄土的蠕变变形量越大;围压和偏应力水平一定时,含水量越高,蠕变越容易,蠕变量越大;黄土具有显著的非线性粘-弹-塑性变形特征.分析认为黑方台黄土普遍表现出稳定型和渐变型的变形特征,进行该地区滑坡预测预报是有科学基础的.以试验数据为基础,采用幂函数和对数函数分别拟合得到黄土的蠕变模型.建议采用对数型经验方程进行黑方台黄土斜坡长期稳定性分析和滑坡预测预报.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号