首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 140 毫秒
1.
裂缝诱导HTI双孔隙介质中的裂缝参数分析   总被引：1，自引：0，他引：1       下载免费PDF全文
裂缝诱导HTI双孔隙介质模型是将一组垂直排列的裂缝系统嵌入到统计各向同性的孔隙岩石基质系统中而建立的.为了研究裂缝参数对地震波在该模型中传播规律的影响,本文分别对裂缝弱度、裂缝孔隙度和裂缝渗透率这三个主要的裂缝参数进行了分析研究.数值结果表明,裂缝诱导HTI双孔隙介质中,裂缝弱度越大,介质的各向异性强度越强;与基质孔隙系统相比,裂缝系统孔隙度对介质等效孔隙度的影响很小,而裂缝系统渗透率的增大则将显著提高介质在裂缝发育方向上的等效渗透率,这符合对裂缝系统"低孔"、"高渗"特性的认识.此外,裂缝系统渗透率的增大也使慢纵波的振幅显著增强.  相似文献   

2.
Variations in fluid density can greatly affect fluid flow and solute transport in the subsurface. Heterogeneities such as fractures play a major role for the migration of variable-density fluids. Earlier modeling studies of density effects in fractured media were restricted to orthogonal fracture networks, consisting of only vertical and horizontal fractures. The present study addresses the phenomenon of 3D variable-density flow and transport in fractured porous media, where fractures of an arbitrary incline can occur. A general formulation of the body force vector is derived, which accounts for variable-density flow and transport in fractures of any orientation. Simulation results are presented that show the verification of the new model formulation, for the porous matrix and for inclined fractures. Simulations of variable-density flow and solute transport are then conducted for a single fracture, embedded in a porous matrix. The simulations show that density-driven flow in the fracture causes convective flow within the porous matrix and that the high-permeability fracture acts as a barrier for convection. Other simulations were run to investigate the influence of fracture incline on plume migration. Finally, tabular data of the tracer breakthrough curve in the inclined fracture is given to facilitate the verification of other codes.  相似文献   

3.
In this article, the quadrupole method is implemented in order to simulate the effects of heterogeneities on one dimensional advective and diffusive transport of a passive solute in porous media. Theoretical studies of dispersion in heterogeneous stratified media can bring insight into transport artefacts linked to scale effects and apparent dispersion coefficients. The quadrupole method is an efficient method for the calculation of transient response of linear systems. It is based here on the Laplace transform technique. The analytical solutions that can be derived by this method assists understanding of upscaled parameters relevant to heterogeneous porous media.First, the method is developed for an infinite homogeneous porous medium. Then, it is adapted to a stratified medium where the fluid flow is perpendicular to the interfaces. The first heterogeneous medium studied is composed of two semi-infinite layers perpendicular to the flow direction each having different transport properties. The concentration response of the medium to a Dirac injection is evaluated. The case studied emphasises the importance in the choice of the boundary conditions.In the case of a periodic heterogeneous porous medium, the concentration response of the medium is evaluated for different numbers of unit-cells. When the number of unit cells is great enough, depending on the transport properties of each layer in the unit cell, an equivalent homogeneous behaviour is reached. An exact determination of the transport properties (equivalent dispersion coefficient) of the equivalent homogeneous porous medium is given.  相似文献   

4.
Computed tomography scan imaging techniques have been used on core samples to investigate the effect of natural open fractures on reservoir flow in the Snøhvit Gas Condensate Field. Firstly, computed tomography (CT) scanning was used to describe the 3D geometrical properties of the fracture network including orientation and fracture density. Two types of fractures were observed: F1 fractures are short and stylolite related and F2 fractures are longer, cross-cutting the core and without any obvious relationship to stylolites. Secondly, monitoring of single and two phase flow experiments on samples containing these two types of natural open fractures was performed under 10 and 80 bar net confining pressure while using CT scanning. 1-phase miscible flooding experiment shows approximately 3 times higher flooding velocity in an open F2 fracture than in the matrix. 2-phase flooding by gas injection into a 100% water saturated core gave early gas breakthrough due to flow in the fracture and thereafter very little water production. The flow experiments showed that the presence of open fractures has a significant local effect on fluid flow even in a case with relatively high matrix porosity (200–300 mD). The sample containing F1 fractures showed a complex flow pattern influenced both by open fractures and stylolites. The CT scan data enables an exact representation of the fracture network in core scale simulation models and therefore improves the understanding of fracture influence on flow in a fractured porous medium. CT scanning of core samples provides an effective tool for integrating geology and fluid flow properties of a porous fractured medium.  相似文献   

5.
Hu BX 《Ground water》2006,44(2):222-233
A Lagrangian stochastic approach is applied to develop a method of moment for solute transport in a physically and chemically nonstationary medium. Stochastic governing equations for mean solute flux and solute covariance are analytically obtained in the first-order accuracy of log conductivity and/or chemical sorption variances and solved numerically using the finite-difference method. The developed method, the numerical method of moments (NMM), is used to predict radionuclide solute transport processes in the saturated zone below the Yucca Mountain project area. The mean, variance, and upper bound of the radionuclide mass flux through a control plane 5 km downstream of the footprint of the repository are calculated. According to their chemical sorption capacities, the various radionuclear chemicals are grouped as nonreactive, weakly sorbing, and strongly sorbing chemicals. The NMM method is used to study their transport processes and influence factors. To verify the method of moments, a Monte Carlo simulation is conducted for nonreactive chemical transport. Results indicate the results from the two methods are consistent, but the NMM method is computationally more efficient than the Monte Carlo method. This study adds to the ongoing debate in the literature on the effect of heterogeneity on solute transport prediction, especially on prediction uncertainty, by showing that the standard derivation of solute flux is larger than the mean solute flux even when the hydraulic conductivity within each geological layer is mild. This study provides a method that may become an efficient calculation tool for many environmental projects.  相似文献   

6.
We study transport of a reactive solute in a chemically heterogeneous porous medium whose chemical properties are uncertain. The dissolved substance undergoes a heterogeneous chemical reaction with a solid phase in the presence of advection caused by extraction/injection from a point source. We present semi-analytical solutions for the probability density function of the solute concentration, which allows us to quantify predictive uncertainty associated with uncertain reaction rate constants for both linear and nonlinear reactions. This enables one to compute probabilities of rare events, which are required for quantitative risk analyses.  相似文献   

7.
The paper provides an introduction to fundamental concepts of mathematical modeling of mass transport in fractured porous heterogeneous rocks. Keeping aside many important factors that can affect mass transport in subsurface, our main concern is the multi-scale character of the rock formation, which is constituted by porous domains dissected by the network of fractures. Taking into account the well-documented fact that porous rocks can be considered as a fractal medium and assuming that sizes of pores vary significantly (i.e. have different characteristic scales), the fractional-order differential equations that model the anomalous diffusive mass transport in such type of domains are derived and justified analytically. Analytical solutions of some particular problems of anomalous diffusion in the fractal media of various geometries are obtained. Extending this approach to more complex situation when diffusion is accompanied by advection, solute transport in a fractured porous medium is modeled by the advection-dispersion equation with fractional time derivative. In the case of confined fractured porous aquifer, accounting for anomalous non-Fickian diffusion in the surrounding rock mass, the adopted approach leads to introduction of an additional fractional time derivative in the equation for solute transport. The closed-form solutions for concentrations in the aquifer and surrounding rocks are obtained for the arbitrary time-dependent source of contamination located in the inlet of the aquifer. Based on these solutions, different regimes of contamination of the aquifers with different physical properties can be readily modeled and analyzed.  相似文献   

8.
When modeling the fate and transport of chemicals in ground water, a common assumption is that sorption equilibrium is achieved rapidly. This local equilibrium assumption is valid when the rate of chemical sorption to soil particles is more rapid than the rate of aqueous chemical change by other processes. However, for some chemicals (e.g., weathered hydrocarbons) this assumption is not necessarily correct. As a result, an increasing body of knowledge related to the extent and rate of release (ROR) of hydrocarbons from soil has been generated.
When evaluating site remediation options, it is important to know when nonequilibrium sorption conditions may have a significant impact on such decisions. In this study, a tiered procedure was developed to consistently evaluate the importance of ROR information at a site. The procedure consists of three tiers, each requiring more information and computational effort than the previous one. The first tier employs three power-law relationships between site parameters and the importance of ROR kinetics to quickly and easily estimate the importance of ROR information at a site. The second tier involves running and evaluating the deterministic component of a ground water fate and transport model. The third tier involves running and evaluating the probabilistic component of the ground water model. Given the sequential nature of the procedure, it is not necessary to perform Tier II (or Tier III) unless the Tier I (or Tier II) evaluation indicates that ROR kinetics may be important at the specific site under consideration. An example of applying the Tier I analysis to a specific site is provided. The results illustrate the influence of the chemical removal processes (e.g., advection and biodegradation) on the predicted importance of ROR kinetics. For the site considered, ROR kinetics had an important impact on model predictions when the biodegradation rate was high.  相似文献   

9.
Large-scale advective transport through highly heterogeneous 3D formations is investigated using highly resolved numerical simulations and simple analytic models. Investigations are focused on impacts of two types of contaminant injection on transport through isotropic formations where flow conditions are uniform in the average. Transport is quantified by analyzing breakthrough curves for control planes at various distances from the injection zone. In flux-proportional injection mode local mass in injection zone is proportional to local groundwater flux; this setup models many practical cases such as contaminant injection through wells. In resident concentration mode local concentration in injection zone is constant. Results show that impacts of injection mode on breakthrough curves and their moments are strong and they persist for hundreds of correlation scales. The resident concentration mode leads to a fatter tails of the breakthrough curves, while the peaks are generally underpredicted. For a synthetic porous medium with logconductivity variance of 8, dispersivity computed using resident concentration mode at control plane 100 integral scales away from the injection zone was about 10 times larger than corresponding one for flux-proportional mode. Hence, injection mode impacts on transport through highly heterogeneous formations are strong and they persist for large distances from the injection zone.  相似文献   

10.
Vertical flow filters are containers filled with porous medium that are recharged from top and drained at the bottom, and are operated at partly saturated conditions. They have recently been suggested as treatment technology for groundwater containing volatile organic compounds (VOCs). Numerical reactive transport simulations were performed to investigate the relevance of different filter operation modes on biodegradation and/or volatilization of the contaminants and to evaluate the potential limitation of such remediation mean due to volatile emissions. On the basis of the data from a pilot‐scale vertical flow filter intermittently fed with domestic waste water, model predictions on the system’s performance for the treatment of contaminated groundwater were derived. These simulations considered the transport and aerobic degradation of ammonium and two VOCs, benzene and methyl tertiary butyl ether (MTBE). In addition, the advective‐diffusive gas‐phase transport of volatile compounds as well as oxygen was simulated. Model predictions addressed the influence of depth and frequency of the intermittent groundwater injection, degradation rate kinetics, and the composition of the filter material. Simulation results show that for unfavorable operation conditions significant VOC emissions have to be considered and that operation modes limiting VOC emissions may limit aerobic biodegradation. However, a suitable combination of injection depth and composition of the filter material does facilitate high biodegradation rates while only little VOC emissions take place. Using such optimized operation modes would allow using vertical flow filter systems as remediation technology suitable for groundwater contaminated with volatile compounds.  相似文献   

11.
Field characterization of a trichloroethene (TCE) source area in fractured mudstones produced a detailed understanding of the geology, contaminant distribution in fractures and the rock matrix, and hydraulic and transport properties. Groundwater flow and chemical transport modeling that synthesized the field characterization information proved critical for designing bioremediation of the source area. The planned bioremediation involved injecting emulsified vegetable oil and bacteria to enhance the naturally occurring biodegradation of TCE. The flow and transport modeling showed that injection will spread amendments widely over a zone of lower‐permeability fractures, with long residence times expected because of small velocities after injection and sorption of emulsified vegetable oil onto solids. Amendments transported out of this zone will be diluted by groundwater flux from other areas, limiting bioremediation effectiveness downgradient. At nearby pumping wells, further dilution is expected to make bioremediation effects undetectable in the pumped water. The results emphasize that in fracture‐dominated flow regimes, the extent of injected amendments cannot be conceptualized using simple homogeneous models of groundwater flow commonly adopted to design injections in unconsolidated porous media (e.g., radial diverging or dipole flow regimes). Instead, it is important to synthesize site characterization information using a groundwater flow model that includes discrete features representing high‐ and low‐permeability fractures. This type of model accounts for the highly heterogeneous hydraulic conductivity and groundwater fluxes in fractured‐rock aquifers, and facilitates designing injection strategies that target specific volumes of the aquifer and maximize the distribution of amendments over these volumes.  相似文献   

12.
We present a forward-modeling investigation of time-dependent ground magnetometric resistivity （MMR） anomalies associated with transient leachate transport in groundwater systems. Numerical geo-electrical models are constructed based on the hydrological simulation results of leachate plumes from a highly conceptualized landfill system and the resultant MMR responses are computed using a modified finite difference software MMR2DFD. Three transmitter configurations （i.e., single source, MMR-TE, and MMR-TM modes） and two hydrological models （i.e., uniform and faulted porous media） are considered. Our forward modeling results for the uniform porous medium indicates that the magnetic field components perpendicular to the dominant current flow contain the most information of the underground targets and the MMR-TE mode is an appropriate configuration for detecting contaminant plumes. The modeling experiments for the faulted porous medium also confirm that the MMR method is capable of mapping and monitoring the extent of contaminant plumes in aroundwater systems.  相似文献   

13.
Biodegradation is an important mechanism for contaminant reduction in groundwater environments; in fact, in situ bioremediation and bioaugmentation methods represent alternatives to traditional methods such as pump-and-treat. Microbial chemotaxis has been shown to significantly increase contaminant degradation in subsurface environments. In this work, the method of volume averaging is used to upscale the microscale chemotactic microbial transport equations in order to obtain the corresponding effective medium models for the mass balance of bacteria and the chemical attractant to which they respond. As a first approach, cellular growth/death and consumption of the attractant by chemical reaction are assumed to be negligible with respect to convective and diffusive transport mechanisms. For microorganisms, two effective coefficients are introduced, namely a total motility tensor and a total velocity vector. Our results show that, under certain conditions, these coefficients can differ considerably from the values corresponding to non-chemotactic transport. These transport coefficients show strong dependence of the microstructure of the porous medium, the fluid flow fields and the distribution of the attractant.  相似文献   

14.
Simulation of heat transport has its applications in geothermal exploitation of aquifers and the analysis of temperature dependent chemical reactions. Under homogeneous conditions and in the absence of a regional hydraulic gradient, groundwater flow and heat transport from or to a well exhibit radial symmetry, and governing equations are reduced by one dimension (1D) which increases computational efficiency importantly. Solute transport codes can simulate heat transport and input parameters may be modified such that the Cartesian geometry can handle radial flow. In this article, SEAWAT is evaluated as simulator for heat transport under radial flow conditions. The 1971, 1D analytical solution of Gelhar and Collins is used to compare axisymmetric transport with retardation (i.e., as a result of thermal equilibrium between fluid and solid) and a large diffusion (conduction). It is shown that an axisymmetric simulation compares well with a fully three dimensional (3D) simulation of an aquifer thermal energy storage systems. The influence of grid discretization, solver parameters, and advection solution is illustrated. Because of the high diffusion to simulate conduction, convergence criterion for heat transport must be set much smaller (10?10) than for solute transport (10?6). Grid discretization should be considered carefully, in particular the subdivision of the screen interval. On the other hand, different methods to calculate the pumping or injection rate distribution over different nodes of a multilayer well lead to small differences only.  相似文献   

15.
Delivery of dissolved chemicals to bioremediate oil from the Exxon Valdez oil spill was investigated at Beach EL056C of Eleanor Island, Prince William Sound, Alaska. The delivery technique was high pressure injection (HPI) of an inert tracer, lithium, at the approximate depth of 1.0 m into the beach near the mid‐tide line. The results revealed that the maximum injection flow rate was 3.0 L/min and the associated pressure was around 196 kPa. Therefore, exceeding any of these values would probably cause failure of the injection system. The injected tracer was monitored at multiple depths of four surrounding observation wells, and the results showed that the tracer plume occupied an area of 12 m2 within 24 h. The tracer plume traveled at the average speeds of 10 m/d in the seaward direction and 1.7 m/d in other directions. The rapid movement under HPI and the large diameter of influence (3.0 m) indicated that bioremediation of the Exxon Valdez oil on this beach via injection of chemicals is logistically feasible.  相似文献   

16.
This paper presents a study on suspended particle transport in porous medium with the aid of a sand layer transportation–deposition testing system to determine the kinetic characteristics of particles in porous medium under variable temperatures. Quartz sand and quartz powder were chosen as the porous medium and particle in the tests, respectively. Four size compositions and two operational modes, that is, temperature reduction mode (changing from 18°C to 5°C) and temperature increment mode (changing from 18°C to 35°C), were adopted. The turbidity and concentration of quartz powder were measured under various conditions. We observed a high temperature‐independent correlation between them. Breakthrough curves under different conditions were analysed using this testing system. The results showed that changes in temperature affected the particle transport process to some extent, and the degree of influence was closely related to the time moment of the temperature change onset. Moreover, we found a hysteresis phenomenon in the breakthrough curve under both temperature reduction and increment conditions. The results also indicated that the temperature effect was particularly significant for smaller particles. The typical curves to represent particle transport process under variable temperatures were put forward according to the results. To explain the test results, four factors, that is, water viscosity, adsorption effect, double layer force, and particle kinetic energy, were considered and categorized as promotion or constraining factors.  相似文献   

17.
This research was conducted to evaluate the combination of electromigration and potassium permanganate as a potential remediation method for low-permeability media (e.g., soil and sediment) contaminated with dissolved and sorbed organic contaminants. The experimental procedure was composed of two stages: determination of migration rates of permanganate through homogeneous cores and a primarily qualitative analysis of migration in more heterogeneous, two-dimensional scenarios. Results indicated that transport of permanganate through fine-grained porous media and clays can be undertaken using electromigration, and electromigration rates were found to be at least 400% faster than diffusion alone. In addition, the use of an applied electric field in a flushing scenario was shown to result in almost 100% sweep efficiency of a domain consisting of clay blocks interspersed in a glass bead medium. The results of the study show that there is potential for this method to be able to deliver permanganate and other potential remedial agents to treat contaminated zones within heterogeneous and low-permeability porous media through in situ chemical oxidation or other processes.  相似文献   

18.
A. Pistocchi 《水文研究》2008,22(13):2292-2314
  相似文献   

19.
Recreation or restoration of salt marsh through the deliberate removal of flood defences (managed realignment or de‐embankment) is a common practice across Europe and the USA, with potential to enhance delivery of ecosystem services. However, recent research suggests that physical, chemical and ecological processes may be impaired in recreated sites as a result of the modified morphology, sediment structure and hydrology associated with both the restoration process and historic land use. This paper compares physical sediment properties and subsurface water levels recorded in paired natural and de‐embanked (recreated) salt marshes in SE England. Using a combination of statistical and time‐series modelling, significant differences between the natural and recreated marshes are identified. Sediment properties (bulk density, moisture content and organic content) within each marsh were statistically different and imply that de‐embanked sediments are compacted, which may affect subsurface water movement. Analysis of hydrological time series reveals that the de‐embanked salt marsh is characterized by a damped response to tidal flooding with elevated and less variable water levels. This, combined with analysis of hydrographs and hysteresis patterns over individual tidal cycles, suggests that fast, horizontal near‐surface flows enhanced by the relict land surface may play a greater role in drainage of the de‐embanked salt marsh. The importance of hydrological functioning in governing many important physical and biogeochemical processes in salt marshes suggests any modifications would have significant implications for the delivery of ecosystem services. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

20.
Zhang J  Clare J  Guo J 《Ground water》2012,50(4):633-638
In the evaluation of potential risk from ingestion of groundwater near an impacted site, numerical simulation of fate and transport processes of chemicals of concern is often required. If there is potential concern about multiple chemicals, numerical simulation of each chemical separately is often needed. In this paper, a semi-analytical solution is presented based on a numerical solution of the transport of a conservative and nonreactive tracer. When multiple chemicals undergoing sorption and first-order degradation need to be modeled, we can avoid performing individual numerical simulations for each chemical by applying the semi-analytical solution. Numerical test runs were conducted to verify the semi-analytical solution; simulation results reveal that the concentrations derived from the semi-analytical solution are identical to those derived from the individual numerical fate and transport model simulations. The semi-analytical solution requires steady-state flow conditions, no continuing contaminant source, and similar initial source concentration distributions.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号